Document the network device statistics counter that are exposed as sysfs
attributes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs documentation for the various attributes of a network
interface exposed in /sys/class/<iface>/queues/{rx,tx}-<queue>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for the phys_port_id sysfs attribute of a network
device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851 SPI ethernet wasn't documented, but we documented the
optional regulator supply for it under the mll based ethernet
chip. Furthermore, that compatible string needed another 'l'. Fix
all of this and document the optional vdd-io and reset-gpios
properties.
Cc: Nishanth Menon <nm@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
Mention the recently added test suite in the documentation file.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit 4266129964 ("[media] DocBook: Move all media docbook
stuff into its own directory") it was possible to build only a single
(or more) book(s) by calling, for example
make htmldocs DOCBOOKS=80211.xml
This now fails:
cp: target `.../Documentation/DocBook//media_api' is not a directory
Ignore errors from that copy to make this possible again.
Fixes: 4266129964 ("[media] DocBook: Move all media docbook stuff into its own directory")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 61b905da33 ("net: Rename skb->rxhash to skb->hash"), skb->rxhash
was renamed to skb->hash. Update references in Documentation
accordingly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Freescale TSEC PHY, Broadcom GENET & SYSTEMPORT Device Tree
binding documentation to refer to the fixed-link Device Tree binding in
fixed-link.txt.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the fixed-link Device Tree binding documentation to contain
information about the old and deprecated 5-digit 'fixed-link' property.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
regressions. As usual most fixes are for platform-specific clock
drivers, but there are also two fixes to the clk core after recent
changes to the way that clock unregistration is handled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=JwFU
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
As usual most fixes are for platform-specific clock drivers, but there
are also two fixes to the clk core after recent changes to the way
that clock unregistration is handled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: tegra: Fix wrong value written to PLLE_AUX
clk: shmobile: clk-mstp: change to using clock-indices
clk: Fix slab corruption in clk_unregister()
clk: Fix double free due to devm_clk_register()
clk: socfpga: fix clock driver for 3.15
clk: divider: Fix best div calculation for power-of-two and table dividers
clk: bcm281xx: don't use unnamed structs or unions
Pull x86 fixes from Peter Anvin.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, modify_ldt: Make support for 16-bit segments a runtime option
x86, mm, hugetlb: Add missing TLB page invalidation for hugetlb_cow()
x86, rdrand: When nordrand is specified, disable RDSEED as well
To benefit from special filters for single SFF or single EFF CAN identifier
subscriptions the CAN_EFF_FLAG bit and the CAN_RTR_FLAG bit has to be set
together with the CAN_(SFF|EFF)_MASK in can_filter.mask.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some Ethernet MACs have a "fixed link", and are not connected to a
normal MDIO-managed PHY device. For those situations, a Device Tree
binding allows to describe a "fixed link" using a special PHY node.
This patch adds:
* A documentation for the fixed PHY Device Tree binding.
* An of_phy_is_fixed_link() function that an Ethernet driver can call
on its PHY phandle to find out whether it's a fixed link PHY or
not. It should typically be used to know if
of_phy_register_fixed_link() should be called.
* An of_phy_register_fixed_link() function that instantiates the
fixed PHY into the PHY subsystem, so that when the driver calls
of_phy_connect(), the PHY device associated to the OF node will be
found.
These two additional functions also support the old fixed-link Device
Tree binding used on PowerPC platforms, so that ultimately, the
network device drivers for those platforms could be converted to use
of_phy_is_fixed_link() and of_phy_register_fixed_link() instead of
of_phy_connect_fixed_link(), while keeping compatibility with their
respective Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An initial attempt on describing some of the odd APIs
provided by this driver.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM43xx phy mode selection is similar to AM33xx platform, so adding only
the compatibility string to the driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dra7xx support for selecting the phy mode which is present in control
module of dra7xx SoC
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems like we've had more fixes than usual this release cycle, but
there's nothing in particular that we're doing differently. Perhaps it's
just one of those cycles where more people are finding more regressions
(and/or that the latency of when people actually test what's been in
the tree for a while is catching up so that we get the bug reports now).
The bigger changes here are are for TI and Marvell platforms:
* Timing changes for GPMC (generic localbus) on OMAP causing some largeish
DTS deltas.
* Fixes to window allocation on PCI for mvebu touching drivers/ stuff. Patches
have acks from subsystem maintainers where needed.
* A fix from Thomas for a botched DT conversion in drivers/edma.
There's a handful of other fixes for the above platforms as well as sunxi,
at91, i.MX. I also included a MAINTAINER update for Broadcom, and a trivial
move of a binding doc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTb4tkAAoJEIwa5zzehBx3BikP/jOrFb9MbjfBjtyiFe9iJtzt
37LCiCXXLpqvB1afdp8Zs4Tp5FLy5Mhc+s8rj/G+s16ijMvQyz4uV/XsyXwPGWHQ
v8gK9yXHja0vPyPZxMCTU9VRUMHHZW6rwUq55h2HI3NcEid+0nEqt7tC5lYjTAmp
v/5p9NAPgWQzDk+MOUwqgDVXVdg8Qui3OnWhWEvoMjDVUWg8c0ettDbu2ztPkf3R
TSJHIvWKoZ5Dyqykvb7RteYwDyZxoEzyPe77U80yrL3f4Y1c2Zj8eZhjKVjKYEOm
H1yJjkDNopkxlCUWKH9ntvmlfZ8fbHMkPW8hKNXWdd0tBNzkfDPbuQ05vnmK4N1o
8nYK6ZiYH9L3YrZ0bupFuf0nt3fL6RaouwofMNqA21v7CG0gkIpI3Or2pUT/lNR4
KuoPMNWR45lUZRWWZPj+3uOpf8WZmqSjG+6AbDJlGF7DBKN3j7N+HHEyrUYZk85o
SzBqIoJrxCPhOWxLyv1IhqLdAZiudDWXaZ3cznjKtLjYrv5I4ZYoArHx13FADic1
zgg4TuG1Rn+gcUZpa+/2+U0LGCg1z0nUtAFs1B+VqQeqOmIeAOpE8+x/4iXv79t/
vIq0jvboQFmv/dGM8f0jFxQqhu5fX0qGQ2OIZOxEiSY5m0ZwyyKWChThBdUklO4D
vlPQu7jhlniYTOxQfMTf
=76ry
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Seems like we've had more fixes than usual this release cycle, but
there's nothing in particular that we're doing differently. Perhaps
it's just one of those cycles where more people are finding more
regressions (and/or that the latency of when people actually test
what's been in the tree for a while is catching up so that we get the
bug reports now).
The bigger changes here are are for TI and Marvell platforms:
* Timing changes for GPMC (generic localbus) on OMAP causing some
largeish DTS deltas.
* Fixes to window allocation on PCI for mvebu touching drivers/
stuff. Patches have acks from subsystem maintainers where needed.
* A fix from Thomas for a botched DT conversion in drivers/edma.
There's a handful of other fixes for the above platforms as well as
sunxi, at91, i.MX. I also included a MAINTAINER update for Broadcom,
and a trivial move of a binding doc.
I know you said you'd be offline this week, but I might as well post
it for when you return. :)"
I'm not quite offline yet. Doing a few pulls in the last hour before my
internet goes away..
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
MAINTAINERS: update Broadcom ARM tree location and add an SoC family
ARM: dts: i.MX53: Fix ipu register space size
ARM: dts: kirkwood: fix mislocated pcie-controller nodes
ARM: sunxi: Enable GMAC in sunxi_defconfig
ARM: common: edma: Fix xbar mapping
ARM: sun7i: Fix i2c4 base address
ARM: Kirkwood: T5325: Fix double probe of Codec
ARM: mvebu: enable the SATA interface on Armada 375 DB
ARM: mvebu: specify I2C bus frequency on Armada 370 DB
ARM: mvebu: use qsgmii phy-mode for Armada XP GP interfaces
ARM: mvebu: fix NOR bus-width in Armada XP OpenBlocks AX3 Device Tree
ARM: mvebu: fix NOR bus-width in Armada XP DB Device Tree
ARM: mvebu: fix NOR bus-width in Armada XP GP Device Tree
ARM: dts: AM3517: Disable absent IPs inherited from OMAP3
ARM: dts: OMAP2: Fix interrupts for OMAP2420 mailbox
ARM: dts: OMAP5: Add mailbox dt node to fix boot warning
ARM: OMAP5: Switch to THUMB mode if needed on secondary CPU
ARM: dts: am437x-gp-evm: Do not reset gpio5
ARM: dts: omap3-igep0020: use SMSC9221 timings
PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
...
With the addition of clock-indices, we need to change the renesas
clock implementation to use these instead of the local definition
of "renesas,clock-indices".
Since this will break booting with older device trees, we add a
simple auto-detection of which properties are present.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
One can logically expect that when the user has specified "nordrand",
the user doesn't want any use of the CPU random number generator,
neither RDRAND nor RDSEED, so disable both.
Reported-by: Stephan Mueller <smueller@chronox.de>
Cc: Theodore Ts'o <tytso@mit.edu>
Link: http://lkml.kernel.org/r/21542339.0lFnPSyGRS@myon.chronox.de
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
make it work. The patch has been tagged for stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=eyxH
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Pull "DaVinci fixes for v3.15" from Sekhar Nori:
The patch fixes EDMA crossbar mapping to actually
make it work. The patch has been tagged for stable.
* tag 'davinci-fixes-for-v3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: common: edma: Fix xbar mapping
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix aliases syntax in device-tree binding example to avoid
copy-paste errors (the alias would be dropped silently).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few fixups to various drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - fix touchpad initialization on Gigabyte U2442
Input: tca8418 - fix loading this driver as a module from a device tree
Input: bma150 - extend chip detection for bma180
Input: atkbd - fix keyboard not working on some LG laptops
Input: synaptics - add min/max quirk for ThinkPad Edge E431
Renames micrel-ksz9021.txt to micrel-ksz90x1.txt and adds documentation for
the KSZ9031 binding from patch 1. Also adds step increment information, and
note about phy fixups.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
The hw_version 3 Elantech touchpad on the Gigabyte U2442 does not accept
0x0b as initialization value for r10, this stand-alone version of the
driver: http://planet76.com/drivers/elantech/psmouse-elantech-v6.tar.bz2
Uses 0x03 which does work, so this means not setting bit 3 of r10 which
sets: "Enable Real H/W Resolution In Absolute mode"
Which will result in half the x and y resolution we get with that bit set,
so simply not setting it everywhere is not a solution. We've been unable to
find a way to identify touchpads where setting the bit will fail, so this
patch uses a dmi based blacklist for this.
https://bugzilla.kernel.org/show_bug.cgi?id=61151
Cc: stable@vger.kernel.org
Reported-by: Philipp Wolfer <ph.wolfer@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
John W. Linville says:
====================
pull request: wireless-next 2014-05-02
Please pull this batch of updates intended for the 3.16 stream...
For the mac80211 bits, Johannes says:
"In this round we have a large number of small features and
improvements from people too numerous to list here. The only really
bit thing is Michał and Luca's CSA work (including changing how
interface combination verification is done)."
For the Bluetooth bits, Gustavo says:
"Here goes some patches for the -next release. There is nothing
really special for this pull request, just a bunch of refactors,
fixes and clean ups."
For the ath10k/ath6kl bits, Kalle says:
"For ath6kl Kalle fixed a bunch of checkpatch warnings.
In ath10k we had more changes, major ones being:
* fix memory allocation failures after a firmware crash (Michal)
* some rework of DFS configuration to enable it correctly in all cases
(Michal)
* add a new firmware crash option to make it possible to crash 10.1
firmware for testing purposes (Marek P)
* fix RTS/CTS protection in certain cases (Marek K)
* fix wrong RSSI and rate reporting in some cases (Janusz)
* fix firmware stats reporting (Chun, Ben & Bartosz)"
For the iwlwifi bits, Emmanuel says:
"I have here a bunch of unrelated things. I disabled support for
-7.ucode which means that I can removed a lot of code. Eliad has
a brand new feature: we reduce the Tx power when the link allows -
this reduces our power consumption. The regular changes in power and
scan area. One interesting thing though is the patches from Johannes,
we have now GRO which allows to increase our throughput in TCP Rx. The
main advantage is that it reduces the number of TCP Acks - these TCP
Acks are completely useless when we are using A-MPDU since the first
packet of the A-MPDU generates a TCP Ack which is made obsolete by
the next packets."
Along with that, there are a variety of updates to b43, mwifiex,
rtl8180 and wil6210 drivers and a handful of other updates here
and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, this patch tries to clarify internal BPF calling
convention and adds internal BPF examples, JIT guide, use cases.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arm64 move of of_clk_init() call in a previous commit
- Default DMA ops changed to non-coherent to preserve compatibility with
32-bit ARM DT files. The "dma-coherent" property can be used to
explicitly mark a device coherent. The Applied Micro DT file has been
updated to avoid DMA cache maintenance for the X-Gene SATA controller
(the only arm64 related driver with such assumption in -rc mainline)
- Fixmap correction for earlyprintk
- kern_addr_valid() fix for huge pages
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=kRLA
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"These are mostly arm64 fixes with an additional arm(64) platform fix
for the initialisation of vexpress clocks (the latter only affecting
arm64; the arch/arm64 code is SoC agnostic and does not rely on early
SoC-specific calls)
- vexpress platform clocks initialisation moved earlier following the
arm64 move of of_clk_init() call in a previous commit
- Default DMA ops changed to non-coherent to preserve compatibility
with 32-bit ARM DT files. The "dma-coherent" property can be used
to explicitly mark a device coherent. The Applied Micro DT file
has been updated to avoid DMA cache maintenance for the X-Gene SATA
controller (the only arm64 related driver with such assumption in
-rc mainline)
- Fixmap correction for earlyprintk
- kern_addr_valid() fix for huge pages"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
vexpress: Initialise the sysregs before setting up the clocks
arm64: Mark the Applied Micro X-Gene SATA controller as DMA coherent
arm64: Use bus notifiers to set per-device coherent DMA ops
arm64: Make default dma_ops to be noncoherent
arm64: fixmap: fix missing sub-page offset for earlyprintk
arm64: Fix for the arm64 kern_addr_valid() function
Since the default DMA ops for arm64 are non-coherent, mark the X-Gene
controller explicitly as dma-coherent to avoid additional cache
maintenance.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Loc Ho <lho@apm.com>
Pull timer fixes from Thomas Gleixner:
"This update brings along:
- Two fixes for long standing bugs in the hrtimer code, one which
prevents remote enqueuing and the other preventing arbitrary delays
after a interrupt hang was detected
- A fix in the timer wheel which prevents math overflow
- A fix for a long standing issue with the architected ARM timer
related to the C3STOP mechanism.
- A trivial compile fix for nspire SoC clocksource"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Prevent overflow in apply_slack
hrtimer: Prevent remote enqueue of leftmost timers
hrtimer: Prevent all reprogramming if hang detected
clocksource: nspire: Fix compiler warning
clocksource: arch_arm_timer: Fix age-old arch timer C3STOP detection issue
Add a resource managed devm_mdiobus_alloc[_size]()/devm_mdiobus_free()
to automatically clean up MDIO bus alocations made by MDIO drivers,
thus leading to simplified MDIO drivers code.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few collections of small eggs that have been gathered during
the Easter holidays. Mostly small ASoC fixes, with a HD-audio
quirk and a workaround for Nvidia controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=M31u
-----END PGP SIGNATURE-----
Merge tag 'sound-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few collections of small eggs that have been gathered during the
Easter holidays. Mostly small ASoC fixes, with a HD-audio quirk and a
workaround for Nvidia controller"
* tag 'sound-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Suppress CORBRP clear on Nvidia controller chips
ALSA: hda - add headset mic detect quirk for a Dell laptop
ASoC: jz4740: Remove Makefile entry for removed file
ASoC: Intel: Fix audio crash due to negative address offset
ASoC: dapm: Fix widget double free with auto-disable DAPM kcontrol
ASoC: Intel: Fix incorrect sizeof() in sst_hsw_stream_get_volume()
ASoC: Intel: some incorrect sizeof() usages
ASoC: cs42l73: Convert to use devm_gpio_request_one
ASoC: cs42l52: Convert to use devm_gpio_request_one
ASoC: tlv320aic31xx: document that the regulators are mandatory
ASoC: fsl_spdif: Fix wrong OFFSET of STC_SYSCLK_DIV
ASoC: alc5623: Fix regmap endianness
ASoC: tlv320aic3x: fix shared reset pin for DT
ASoC: rsnd: fix clock prepare/unprepare
clockevent fixes for 3.15 from Daniel Lezcano:
* Lorenzo Pieralizi fixed an issue with the arch_arm_timer where the
C3STOP flag for all the arch can cause some trouble by setting the
flag only if the power domain is not always on
* Alexander Shiyan fixed a compilation by changing the init function
to the right prototype
This is another great example of trainwreck engineering:
commit 2646a0e529 (ARM: edma: Add EDMA crossbar event mux support)
added support for using EDMA on peripherals which have no direct EDMA
event mapping.
The code compiles and does not explode in your face, but that's it.
1) Reading an u16 array from an u32 device tree array simply does not
work. Even if the function is named "edma_of_read_u32_to_s16_array".
It merily calls of_property_read_u16_array. So the resulting 16bit
array will have every other entry = 0.
2) The DT entry for the xbar registers related to xbar has length 0x10
instead of the real length: 0xfd0 - 0xf90 = 0x40.
Not a real problem as it does not cross a page boundary, but
wrong nevertheless.
3) But none of this matters as the mapping never happens:
After reading nonsense edma_of_read_u32_to_s16_array() invalidates
the first array entry pair, so nobody can ever notice the
braindamage by immediate explosion.
Seems the QA criteria for this code was solely not to explode when
someone adds edma-xbar-event-map entries to the DT. Goal achieved,
congratulations!
Not really helpful if someone wants to use edma on a device which
requires a xbar mapping.
Fix the issues by:
- annotating the device tree entry with "/bits/ 16" as documented in
the of_property_read_u16_array kernel doc
- make the size of the xbar register mapping correct
- invalidating the end of the array and not the start
This convoluted mess wants to be completely rewritten as there is no
point to keep the xbar_chan array memory and the iomapping of the xbar
regs around forever. Marking the xbar mapped channels as used should
be done right there.
But that's a different issue and this patch is small enough to make it
work and allows a simple backport for stable.
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
ARM arch timers are tightly coupled with the CPU logic and lose context
on platform implementing HW power management when cores are powered
down at run-time. Marking the arch timers as C3STOP regardless of power
management capabilities causes issues on platforms with no power management,
since in that case the arch timers cannot possibly enter states where the
timer loses context at runtime and therefore can always be used as a high
resolution clockevent device.
In order to fix the C3STOP issue in a way compliant with how real HW
works, this patch adds a boolean property to the arch timer bindings
to define if the arch timer is managed by an always-on power domain.
This power domain is present on all ARM platforms to date, and manages
HW that must not be turned off, whatever the state of other HW
components (eg power controller). On platforms with no power management
capabilities, it is the only power domain present, which encompasses
and manages power supply for all HW components in the system.
If the timer is powered by the always-on power domain, the always-on
property must be present in the bindings which means that the timer cannot
be shutdown at runtime, so it is not a C3STOP clockevent device.
If the timer binding does not contain the always-on property, the timer is
assumed to be power-gateable, hence it must be defined as a C3STOP
clockevent device.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Magnus Damm <damm@opensource.se>
Cc: Marc Carino <marc.ceeeee@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Device Tree bindings documentation for the Broadcom SYSTEMPORT
Ethernet MAC controller hardware.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devicetree bindings for the at86rf230 IEEE 802.15.4 SPI
device driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- one little DT fix
- the use of proper directory for clock in include/dt-bindings
it allows to remove the now empty include/dt-bindings/clk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTUZz4AAoJEAf03oE53VmQ4CoH/iFAHAhgke2ZBCIXF+ol0xIX
fC9NInNfsejKZbCVcRiyi3HCjJ0TsRJq2QViF+7vnS6/xn0N6rrkDpvPWHNpC87W
fsA3dKlmhZtAv/pPUsUQyUm5BOeuj8lHf38ybt8kLH/UVwGjHnLMsMfTWwAGZEZ7
50wVT2NOm4LwEjqrhMlwPxLiuueXGg4j0x5qOy/akoNYrJGCJzBxyf/h8uSlAp8n
pGbNOpr2D+zzVyeyxjb4fzwfwK4ABSnsRY+Duyf7wcY5I1GVKEC54W2pDUDRBwW5
2Vq7b54hRgHwtmDPK9JkhMLAUOGa7O/S8A/Iu3fe+CkJRyxzXIuJ9Zdpj6eEve8=
=Yg6/
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
3.15 fixes for AT91
- one little DT fix
- the use of proper directory for clock in include/dt-bindings
it allows to remove the now empty include/dt-bindings/clk
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
dt-bindings: clock: Move at91.h to dt-bindigs/clock
ARM: at91: fix spi cs on sama5d3 Xplained board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.
The default value of the parameter is set to "1" mimicing the earlier
behavior.
Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -
netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920
Transactions per second:
Before change: 1,367.11
After change: 1,470.65
Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.
Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).
Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should make the driver usable with VIA/WonderMedia ARM-based
Systems-on-Chip integrated Rhine III adapters. Note that these
are always in MMIO mode, and don't have any known EEPROM.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
