Consistency throughout the code base is good and remove some room for
mistakes (as explained in the "drm/i915: Use a pipe variable to cycle
through the pipes" commit)
So, let's replace the for_each_pipe(i) occurences by for_each_pipe(pipe)
when it's reasonable and practical to do so (eg. when there isn't another
pipe variable already).
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We capture error state not only when the GPU hangs but also on
other situations as in interrupt errors and in situations where
we can kick things forward without GPU reset. There will be log
entry on most of these cases. But as error state capture might be
only thing we have, if dmesg was not captured. Or as in GEN4 case,
interrupt error can trigger error state capture without log entry,
the exact reason why capture was made is hard to decipher.
v2: Split out the the error code stuff to separate patch (Ben)
References: https://bugs.freedesktop.org/show_bug.cgi?id=74193
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we've missed a few more than what Fengguang's 0-day tester
recently reported in i915_irq.c ... Makes sparse happy again (ignore
some spurious stuff about ksyms of exported functions).
Cc: kbuild test robot <fengguang.wu@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a bit of polish which I hope will help me with massaging some
internal patches to use Imre's reworked pipestat handling:
- Don't check for underrun reporting or enable pipestat interrupts
twice.
- Frob the comments a bit.
- Do the iir PIPE_EVENT to pipe mapping explicitly with a switch. We
only have one place which does this, so better to make it explicit.
v2: Ville noticed that I've broken the logic a bit with trying to
avoid checking whether we're interested in a given pipe twice. push
the PIPESTAT read down after we've computed the mask of interesting
bits first to avoid that duplication properly.
v3: Squash in fixups from Imre on irc.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call the handlers for pending pipestat interrupt events even if
they aren't explicitly enabled by i915_enable_pipestat(). This isn't an
issue for events other than the vblank start event, since those are
always enabled anyways. Otoh, we enable the vblank start event
on-demand, so we'll end up calling the vblank handler at times when they
are disabled.
I haven't checked if this causes any real problem, but for consistency
and to remove some overhead we should still fix this by clearing /
handling only the enabled interrupt events. Also this is a dependency
for the upcoming VLV power domain patchset where we need to disable all
the pipestat interrupts whenever the display power well is off.
v2:
- inline the status->enable mask mapping (Ville)
- don't check for invalid PSR bit on platforms other than VLV (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Frob conflict due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV we can't get at the pipestat status bits by simply right
shifting the corresponding enable bits. The mapping between enable and
status bits for the sprite0,1 flip done and the PSR events don't follow
this rule, so we need to map them separately.
The PSR enable for pipe A is DPFLIPSTAT[22], but I haven't added support
for this, since there is no user of it atm. Until support is added WARN
if someone tries to enable PSR interrupts, or tries to enable the same
(1 << 6) bit on pipe B, which MBZ.
v2:
- inline the status->enable mask mapping (Ville)
- fix bogus use of status bits in enable mask (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There isn't any PSR interrupt enable bit for pipe A, so we couldn't
enable it through the current API. Passing the corresponding status bits
solves this and also makes the mapping between enable and status bits
simpler on VLV (addressed in an upcoming patch).
Except of checking for invalid status bit arguments, no functional
change.
v2: split out the low level parts of i915_enable_pipestat accepting
separate enabled and status masks, to make the non-standard mapping
between those masks stand out more (added in the next patch)
(Jesse,Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we make sure that all the dev_priv->info usages are wrapped by
INTEL_INFO(), we can easily modify the ->info field to be structure and
not a pointer while keeping the const protection in the INTEL_INFO()
macro.
v2: Rebased onto latest drm-nightly
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
s/FLIPDONE/FLIP_DONE/ to make all FLIP_DONE macro names consistent.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be used by other platforms too, so factor it out.
The only functional change is the reordeing of gmbus_irq_handler() wrt.
the hotplug handling, but since it only schedules a work, it isn't an
issue.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Don't keep on using the private_t typedef.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec and the code suggests that the interrupt signaled by IIR[7,5]
(DISPLAY_PIPE_A/B_VBLANK) is a first level IRQ flag for the second
level PIPEA/BSTAT[2] (Start of Vertical Blank) interrupt. Measuring
the relative timings of when IIR[7] and PIPEASTAT[1,2] get set and
checking the effect of unmasking different pipestat and IIR events
shows that this isn't so:
First, ISR/IIR[7] gets set independently of PIPEASTAT[18] (Start of
Vertical Blank Enable) or any other pipestat enable bit, so it isn't
a first level IRQ bit showing the state of PIPEASTAT[2], but is
connected directly to the timing generator.
Second, setting only PIPEASTAT[18] and leaving all other pipestat events
disabled, IIR[6] (DISPLAY_PIPE_A_EVENT) gets set close to the moment when
PIPEASTAT[2] gets set, so the former is a first level interrupt flag for
the latter. The bspec is rather unclear about this, but I also assume
that IIR[6] signals all pipestat A events, except PIPEASTAT[31] (FIFO
Under-run Status).
Third, IIR[7] is set close to the moment when PIPEASTAT[1] (Framestart
Interrupt) gets set, in the mode I used about 12usec after PIPEASTAT[2]
and IIR[6] gets set. This means the IIR[7] isn't marking the start of
vblank, but rather signals the framestart event.
Based on the above, we don't need to unmask IIR[7] when waiting for
start of vblank events, but we can rely on IIR[6] being always unmasked,
which will signal when PIPEASTAT[2] gets set. Doing this will also get
rid of the overhead of getting an interrupt and servicing IIR[7], which
is atm raised always some time after IIR[6]/PIPEASTAT[2] is raised.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we enter RC6 and GFX Clocks are off, the voltage remains higher
than Vmin. When we try to set the freq to RPn, it might fail since the
Gfx clocks are down. So to fix this in Gfx idle, Bring the GFX clock up
and set the freq to RPn then move GFx down.
v2: remove vlv_update_rps_cur_delay function. Update commit message (Daniel)
v3: Fix the timeout during wait for gfx clock (Jesse)
v4: addressed comments on set freq and punit wait (Ville)
v5: use wait_for while waiting for GFX clk to be up. (Daniel)
update cur_delay before requesting min_delay. (Ville)
v6: use wait_for while waiting for punit. (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With full ppgtt using acthd is not enough to find guilty
batch buffer. We get multiple false positives as acthd is
per vm.
Instead of scanning which vm was running on a ring,
to find corressponding context, use a different, simpler,
strategy of finding batches that caused gpu hang:
If hangcheck has declared ring to be hung, find first non complete
request on that ring and claim it was guilty.
v2: Rebase
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73652
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When current delay is already at max delay, Let's disable the PM UP
THRESHOLD INTRRUPTS, so that we will not get further interrupts until
current delay is less than max delay, Also request for the PM DOWN
THRESHOLD INTRRUPTS to indicate the decrease in clock freq. and
viceversa for PM DOWN THRESHOLD INTRRUPTS.
v2: Use bool variables (Daniel)
v3: Fix Interrupt masking bit (Deepak)
v4: Use existing symbolic constants in i915_reg.h (Daniel)
v5: Add pm interrupt mask after new_delay calculation (Ville)
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Pass new_delay by value as suggested by Ville. Also appease
checkpatch.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to see these without having full debugs enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fix the gen8 irq handler as spotted by Paulo in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we print all pipe underruns on GMCH platforms. Hook up the
same logic we use on PCH platforms where we disable the underrun
reporting after the first underrun.
Underruns don't actually generate interrupts themselves on GMCH
platforms, we just can detect them whenever we service other
interrupts. So we don't have any enable bits to worry about. We just
need to remember to clear the underrun status when enabling underrun
reporting.
Note that the underrun handling needs to be moved to the non-locked
pipe_stats[] loop in the interrupt handlers to avoid having to rework
the locking in intel_set_cpu_fifo_underrun_reporting().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not sure anyone cares about this information. I suppose most people
would just look at /proc/interrupts instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
irq_received is used as a boolean in i965_irq_handler(), so make it
bool. This also makes i965_irq_handler() closer to i915_irq_handler().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewd-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add intel_hpd_irq_uninstall() which will cancel the hotplug re-enable
timer.
Also s/i915_reenable_hotplug_timer_func/intel_hpd_irq_reenable/
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we don't print these events for all platforms and for VLV/G4X we
also print them for DP AUX completion events which is unnecessary spam.
Fix both issues.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-PCH platforms ISR doesn't seem to be an actual ISR, at least as
far as display interrupts are concerned. Instead it sort of looks like
some ISR bits just directly reflect the corresponding bit from PIPESTAT.
The bit appears in the ISR only if the PIPESTAT interrupt is enabled. So
in that sense it sort of looks a bit like the south interrupt scheme on
PCH platforms. So it goes something a bit like this:
PIPESTAT.status & PIPESTAT.enable -> ISR -> IMR -> IIR -> IER -> actual
interrupt
In any case that means the intel_pipe_in_vblank_locked() doesn't actually
work for pre-PCH platforms. As a last resort, add a similar kludge as radeon
has that fixes things up if we got called from the vblank interrupt,
but the scanline counter value indicates that we're not quite there yet.
We know that the scanline counter increments at hsync but is otherwise
accurate, so we can limit the kludge to the line just prior to vblank
start, instead of the relative distance that radeon uses.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Preparation for moving the early vblank IRQ logic into
radeon_get_crtc_scanoutpos().
v2: Fix radeon_drv.c compile warning (Mario)
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The scanline counter counts lines in the current field, not the entire
frame. But the crtc_ timings are the values for the entire frame. Divide
the vertical timings by 2 to make them match the scanline counter.
The rounding was carefully chosen to make it do the right thing wrt. the
observed scanline counter and ISR vblank bit behaviour.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rather than using crtc->hwmode, just pass the relevant mode to
drm_calc_vbltimestamp_from_scanoutpos(). This removes the last hwmode
usage from core drm.
Reviewed-by: mario.kleiner.de@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Conflicts are getting out of hand, and now we have to shuffle even
more in -next which was also shuffled in -fixes (the call for
drm_mode_config_reset needs to move yet again).
So do a proper backmerge. I wanted to wait with this for the 3.13
relaese, but alas let's just do this now.
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_pm.c
Besides the conflict around the forcewake get/put (where we chaged the
called function in -fixes and added a new parameter in -next) code all
the current conflicts are of the adjacent lines changed type.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were apparently relying on the defaults on BDW, which resulted in no
hotplug or AUX interrupts. So be sure to call the ibx_irq_preinstall to
enable all interrupts.
v2: use preinstall instead of redundant SDIER write
References: https://bugs.freedesktop.org/show_bug.cgi?id=72834
References: https://bugs.freedesktop.org/show_bug.cgi?id=72833
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel thought that this was an opportune moment to include which pins
and bits ended up being stuck in the WARN.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disabling the hotplug IRQ is a two-step process. First, inside the IRQ
handler we mark the rogue hotplug pin for disabling. Then later in the
hotplug worker, we actually disable the hotplug pin. So we should not
WARN about the rogue hotplug IRQ being sent until after we have
completed disabling the pin.
References: https://bugzilla.redhat.com/show_bug.cgi?id=1051170
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that hardware that is broken enough to emit a hotplug IRQ even
though the pin is surposedly disable, will do so indefinitely.
Note: There's a good chance the underlying issue has been fixed with
commit 0ce99f749b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 26 11:27:49 2013 +0200
drm/i915: fix gen4 digital port hotplug definitions
References: https://bugzilla.redhat.com/show_bug.cgi?id=1051170
Link: https://bugzilla.redhat.com/attachment.cgi?id=847786
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about the potential fix.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We specifically exclude original gen4 (i.e. i965g/gm), so update the
naming for consistency. Spotted while reviewing related code due to a
report from Jesse about byt needing again different values.
v2: g4x, not gm45 since this also applies to the desktop version.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My OCD just couldn't let this slide. Spotted while reviewing Ville's
patch to only flip planes when we have FBC.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like 830M doesn't quite like it when you try to move a plane from
one pipe to another. It seems that the plane's old pipe has to be active
even if the plane is already disabled, otherwise the relevant register
just won't accept new values.
The following commit:
commit 1f1c2e2468
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Nov 28 17:30:01 2013 +0200
drm/i915: Swap primary planes on gen2 for FBC
caused a regression on 830M. It will attempt to swap the planes when the
driver is loaded, but at that time only pipe A might be active, so plane
A gets disabled, but plane B won't get enabled since pipe B is not
active when we try to move the plane over to pipe A.
There's no reason to swap planes on 830M since it doesn't support
FBC. Change the logic a bit to limit the plane swapping to platforms
which actually support FBC. This should avoid getting a black screen on
830M.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to merge PC8 and D3 into a single feature, and when we're
in D3 we won't get any hotplug interrupt anyway, so leaving them
enable doesn't make sense, and it also brings us a problem. The
problem is that we get a hotplug interrupt right when we we wake up
from D3, when we're still waking up everything. If we fully disable
interrupts we won't get this hotplug interrupt, so we won't have
problems.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only plane A is FBC capable on gen2 (like gen3), but the panel fitter
is hooked up to pipe B, so we want to prefer pipe B + plane A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add the code comment Chris requested in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we have this everywhere. Next up would be to wire up the DP
hotplug pin to speed up panel power sequencing for eDP panels ...
I've decided to leave the has_aux_irq logic in the code, it should
come handy for hw bringup.
For testing/fail-safety the dp aux code already has a timeout when
waiting for interrupts to signal completion and screams rather loud if
they don't arrive in time. Given that we need a real piece of hw to
talk to anyway this is probably as good as it gets.
v2: Don't check the dp aux channel bits on i965 machines, they have a
different meaning there. Yay for reusing bits at will! Spotted by
Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
reset_counter will be incremented twice per successful
reset. Odd values mean reset is in progress and even values
mean that reset has completed.
Reset status ioctl introduced in following commit
needs to deliver global reset count to userspace so
use reset_counter to derive the actual reset count
for the gpu
Note that reset in progress is enough to increment
the counter.
v2: wedged equals reset in progress (Daniel Vetter)
v3: Fixed stale comments (Damien Lespiau)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So here's the Broadwell pull request. From a kernel driver pov there's
two areas with big changes in Broadwell:
- Completely new enumerated interrupt bits. On the plus side it now looks
fairly unform and sane.
- Completely new pagetable layout.
To ensure minimal impact on existing platforms we've refactored both the
irq and low-level gtt handling code a lot in anticipation of the bdw push.
So now bdw enabling in these areas just plugs in a bunch of vfuncs.
Otherwise it's all fairly harmless adjusting of switch cases and
if-ladders to shovel bdw into the right blocks. So minimized impact on
existing platforms. I've also merged the bdw-stage1 branch into our
-nightly integration branch for the past week to make sure we don't break
anything.
Note that there's still quite a flurry or patches floating around, but
I've figured I'll push this out. I plan to keep the bdw fixes separate
from my usual -fixes stream so that you can reject them easily in case it
still looks like too much churn. Also, bdw is for now hidden behind the
preliminary hw enabling module option. So there's no real pressure to get
follow-up patches all into 3.13.
* tag 'bdw-stage1-2013-11-08-v2' of git://people.freedesktop.org/~danvet/drm-intel: (75 commits)
drm/i915: Mask the vblank interrupt on bdw by default
drm/i915: Wire up cpu fifo underrun reporting support for bdw
drm/i915: Optimize gen8_enable|disable_vblank functions
drm/i915: Wire up pipe CRC support for bdw
drm/i915: Wire up PCH interrupts for bdw
drm/i915: Wire up port A aux channel
drm/i915: Fix up the bdw pipe interrupt enable lists
drm/i915: Optimize pipe irq handling on bdw
drm/i915/bdw: Take render error interrupt out of the mask
drm/i915/bdw: Add BDW PCH check first
drm/i915: Use hsw_crt_get_config on BDW
drm/i915/bdw: Change dp aux timeout to 600us on DDIA
drm/i915/bdw: Enable trickle feed on Broadwell
drm/i915/bdw: WaSingleSubspanDispatchOnAALinesAndPoints
drm/i915/bdw: conservative SBE VUE cache mode
drm/i915/bdw: Limit SDE poly depth FIFO to 2
drm/i915/bdw: Sampler power bypass disable
ddrm/i915/bdw: Disable centroid pixel perf optimization
drm/i915/bdw: BWGTLB clock gate disable
drm/i915/bdw: Implement edp PSR workarounds
...
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HW engineers have listened and given us again a real interrupt with
masking and status regs. Yay!
For consistency with other platforms call the #define FIFO_UNDERRUN.
Eventually we also might need to have some enable/disable functions
for bdw display interrupts, but for now open-coding seems to be good
enough.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's cache the IMR value like on other platforms. This is needed to
implement the underrun reporting since then we'll have two places that
change the same register at runtime.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The layout of the CRC registers is the same as on hsw, only the
interrupt handling has changed a bit. So trivial to wire up, yay!
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gives us hotplug, gmbus, dp aux and south errors (underrun
reporting!).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Useful for dp aux to work better. Also stop enabling the port A
hotplug event - eDP panels are expected to fire that interupt and
we're not really ready to deal with them. This is consistent with how
we handle port A on ilk-hsw.
The more important bit is that we must delay the enabling of hotplug
interrupts until all the encoders are fully set up. But we need irq
support earlier than that, hence hotplug interrupts can only be
enabled in the ->hpd_irq_setup callback.
v2: Drop the _HOTPLUG, it isn't (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Pipe underrun can't just be enabled, we need some support code like
on ilk-hsw to make this happen. So drop it for now.
- CRC error is a special mode of the CRC hardware that we don't use,
so again drop it. Real CRC support for bdw will be added later.
- All the other error bits are about faults, so rename the #define and
adjust the output.
v2: Use pipe_name as pointed out by Ville. Ville's comment was on a
previous patch, but it was easier to squash in here.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a per-pipe bit in the master irq control register, so use it.
This allows us to drop the masks for aggregate interrupt bits and be a
bit more explicit in the code. It also removes one indentation level.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.
The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.
For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).
The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).
Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.
v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.
v3: fix DE_MISC IER offset
v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.
v5: Rebased on to of recent pch hotplug setup changes.
v6: Fixup on top of moving num_pipes to intel_info.
v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.
v8: Rebase on top of Jani's asle handling rework.
v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/
v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>
v11: Rebase on top of the interrupt cleanups in upstream.
v12: Rebase on top of Ben's DPF changes in upstream.
v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.
v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bikeshed
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
