Linux 3.2-rc7
* tag 'v3.2-rc7': (1304 commits)
Linux 3.2-rc7
netfilter: xt_connbytes: handle negation correctly
Btrfs: call d_instantiate after all ops are setup
Btrfs: fix worker lock misuse in find_worker
net: relax rcvbuf limits
rps: fix insufficient bounds checking in store_rps_dev_flow_table_cnt()
net: introduce DST_NOPEER dst flag
mqprio: Avoid panic if no options are provided
bridge: provide a mtu() method for fake_dst_ops
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
sparc64: Fix MSIQ HV call ordering in pci_sun4v_msiq_build_irq().
pata_of_platform: Add missing CONFIG_OF_IRQ dependency.
ipv4: using prefetch requires including prefetch.h
VFS: Fix race between CPU hotplug and lglocks
vfs: __read_cache_page should use gfp argument rather than GFP_KERNEL
USB: Fix usb/isp1760 build on sparc
net: Add a flow_cache_flush_deferred function
...
Conflicts:
drivers/media/common/tuners/tda18218.c
drivers/media/video/omap3isp/ispccdc.c
drivers/staging/media/as102/as102_drv.h
The ati_remote driver currently uses 2-byte scancodes. However, one of
those bytes is actually a checksum and therefore shouldn't be considered
as part of the scancode.
Fix the driver to only use the actual data byte as a scancode and to
check the checksum itself. Update the bundled keymaps accordingly.
Since ati_remote was only migrated to the rc subsystem for 3.2, the
previous scancodes weren't emitted on any stable kernel.
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed submit urb logic so hardware doesn't hang trying to transmit
signal data
Removed unneeded enable/disable detector commands in
redrat3_transmit_ir (the hardware does this anyway) and converted
arguments to unsigned as per 5588dc2
Signed-off-by: Andrew Vincer <andrew@redrat.co.uk>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I get this error when compiling for_v3.3:
There is a include <linux/module.h> missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch to the IR RC6 decoder adds support for variable length
mode-6A frames which can range in size from 8 to 128 bits. Please refer
to the following link for a detailed explanation or RC6 frames:
http://slydiman.narod.ru/scr/kb/rc6.htm
This change removes the assumption that frames are fixed length
(currently either 24 or 32 data bits) and actually counts the number of
bits until an end of frame marker is seen.
[mchehab@redhat.com: Tested with a RC-6(0) IR - 16 bits]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.2-rc2': (3068 commits)
Linux 3.2-rc2
hfs: add sanity check for file name length
fsl-rio: fix compile error
blackfin: Fixup export.h includes
Blackfin: add serial TX IRQ in individual platform resource
virtio-pci: fix use after free
ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
drm/radeon/kms/combios: fix dynamic allocation of PM clock modes
[CPUFREQ] db8500: fix build error due to undeclared i variable
bma023: Add SFI translation for this device
vrtc: change its year offset from 1960 to 1972
ce4100: fix a build error
arm/imx: fix imx6q mmc error when mounting rootfs
arm/imx: fix AUTO_ZRELADDR selection
arm/imx: fix the references to ARCH_MX3
ARM: mx51/53: set pwm clock parent to ipg_perclk
btrfs: rename the option to nospace_cache
drm/radeon/kms/pm: switch to dynamically allocating clock mode array
drm/radeon/kms: optimize r600_pm_profile_init
drm/radeon/kms/pm: add a proper pm profile init function for fusion
...
Conflicts:
drivers/media/radio/Kconfig
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in clocksource
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two macros were in module.h but now module.h is no longer
sprayed across every source file imaginable, so the users need
to expicitly call out their use of them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix:
drivers/media/rc/ir-raw.c: In function 'init_decoders':
drivers/media/rc/ir-raw.c:354:2: error: implicit declaration of function 'request_module'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The code here treated user pointers correctly, but the __user tags
weren't used correctly so it caused Sparse warnings:
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts some ifdef'd wrapper functions from macros to static inline
functions to kill the following warnings issued by GCC:
CC [M] drivers/media/rc/ir-raw.o
drivers/media/rc/ir-raw.c: In function ‘init_decoders’:
drivers/media/rc/ir-raw.c:353:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:354:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:355:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:356:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:357:2: warning: statement with no effect [-Wunused-value]
drivers/media/rc/ir-raw.c:359:2: warning: statement with no effect [-Wunused-value]
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: <linux-media@vger.kernel.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The protocol differs by having two toggle bits in the scancode. Since
one of the bits is otherwise unused, we can safely handle the bits
unconditionally.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ati_remote_dump() function tries to not print "Weird byte" warning
for 1-byte responses that contain 0xff or 0x00, but it doesn't work
properly as it simply falls back to the "Weird data" warning in the else
clause.
Fix that by adding an inner if clause.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The keycode mangling algorithm is kept the same, so the new external
keymap has the same values as the old static table.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon devices have either 1 or 2 usb interfaces on them, each wired
up to its own urb callback. The interface 0 urb callback is wired up
before the imon context's rc_dev pointer is filled in, which is
necessary for imon 0xffdc device auto-detection to work properly, but we
need to make sure we don't actually run the callback routines until
we've entirely filled in the necessary bits for each given interface,
lest we wind up oopsing. Technically, any imon device could have hit
this, but the issue is exacerbated on the 0xffdc devices, which send a
constant stream of interrupts, even when they have no valid key data.
CC: Andy Walls <awalls@md.metrocast.net>
CC: Chris W <lkml@psychogeeks.com>
Reported-by: Chris W <lkml@psychogeeks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.1-rc6': (1902 commits)
Linux 3.1-rc6
ioctl: register LTTng ioctl
fuse: fix memory leak
fuse: fix flock breakage
Btrfs: add dummy extent if dst offset excceeds file end in
Btrfs: calc file extent num_bytes correctly in file clone
btrfs: xattr: fix attribute removal
Btrfs: fix wrong nbytes information of the inode
Btrfs: fix the file extent gap when doing direct IO
Btrfs: fix unclosed transaction handle in btrfs_cont_expand
Btrfs: fix misuse of trans block rsv
Btrfs: reset to appropriate block rsv after orphan operations
Btrfs: skip locking if searching the commit root in csum lookup
btrfs: fix warning in iput for bad-inode
Btrfs: fix an oops when deleting snapshots
[media] vp7045: fix buffer setup
[media] nuvoton-cir: simplify raw IR sample handling
[media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
[media] v4l2: Fix documentation of the codec device controls
[media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
...
The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add pr_fmt.
Convert ene_warn and ene_notice to pr_<level>.
Use pr_debug in __dbg macro and a little neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
The following patch adds the IR code for the missing "OK" key to the Pinnacle
PCTV HD map. This map is now used by the PCTV 290e DVB-T2 device, whose remote
control has 26 buttons.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add note about recent updates coming from Microsoft's publicly available
specs on Windows Media Center remotes and receivers/transmitters.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than dumping out hex values, lets print the actual calculated
frequency and period the hardware has been configured for. After this
[ 2643.276215] mceusb 3-1:1.0: tx data: 9f 07 (length=2)
[ 2643.276218] mceusb 3-1:1.0: Get carrier mode and freq
[ 2643.277206] mceusb 3-1:1.0: rx data: 9f 06 01 42 (length=4)
[ 2643.277209] mceusb 3-1:1.0: Got carrier of 37037 Hz (period 27us)
Matches up perfectly with the table in Microsoft's docs.
Of course, I've noticed on one of my devices that the MS-recommended
default value of 1 for carrier pre-scaler and 66 for carrier period was
butchered, and instead of converting 66 to hex (0x42 like above), they
put in 0x66, so the hardware reports a default carrier of 24390Hz.
Fortunately, I guess, this particular device is rx-only, but I wouldn't
put it past other hw to screw up here too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the specs, you can read the number of tx ports, number of
rx sensors, which tx ports have cables plugged into them, and which rx
sensors are active. In practice, most of my devices do seem to report
sane values for tx ports and rx sensors (but not all -- one without any
tx ports reports having them), and most report the active sensor
correctly, but only one of eight reports cabled tx ports correctly. So
for the most part, this is just for informational purposes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Supposedly, there are essentially three different classes of devices
that are compatible with Microsoft's specs. First are the "legacy"
devices, which are built using Microsoft-provided hardware specs and
firmware. Second are "emulator" devices, which are built using custom
hardware and firmware, written to emulate Microsoft's firmware. Third
are "port" devices, which have their own device driver and firmware,
which provides compatible data to higher levels of the stack.
>From what I can tell, things like nuvoton-cir and fintek-cir are
essentially "port" devices -- their raw IR buffer format is very similar
to that of the mceusb devices. Now, within the mceusb driver, we have
three different "generations", which at first, seemed like maybe they
mapped to emulator versions. Unfortuantely, every single device I have
responds "illegal command" to the query to get firmware emulator version
from the hardware, which means they're either all emulator version 1, or
they're legacy devices, and our different "generations" aren't at all
related here. Though in theory, its possible the gen1 devices are
"legacy" devices and the rest are emulator v1. There are some useful
features of the v2 interface I was hoping to play with, but alas...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to MS docs, the device firmware may halt after receiving an
unknown instruction, but that it should be possible to tell the firmware
to continue running by simply sending a device resume command. So lets
do that.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Its not uncommon for folks to force these bits enabled, because people
do want to wake their htpc kit via their remote. Lets just set the bits
for 'em.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes the init routine is blasting commands out to the hardware
faster than it can reply. Throw a brief delay in there to give the
hardware a chance to reply before we send the next command.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I was recently pointed to the document titled
Windows-Media-Center-RC-IR-Collection-Green-Button-Specification-03-08-2011-V2.pdf
which as of this writing, is publicly available from
download.microsoft.com. It covers a LOT of the gaps in the mceusb
driver, which to this point, was written almost entirely by
reverse-engineering. First up, I'm updating the defines for all the MCE
commands and responses to match their names in the spec. More to come...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are folks with flaky imon hardware out there that doesn't always
respond to requests to write to their displays for some reason, which
can flood logs quickly when something like lcdproc is trying to
constantly update the display, so lets rate-limit all that error spew.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc unregister logic were deadly broken, preventing some drivers to
be removed. Among the broken things, rc_dev_uevent() is being called
during device_del(), causing a data filling on an area that it is
not ready anymore.
Also, some drivers have a stop callback defined, that needs to be called
before data removal, as it stops data polling.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: warning: function declaration isn't a prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is admittedly a bit of a hack, but if we change our timeout value
to something longer and fudge our synthesized trailing space sample
based on the initial pulse sample, rc-core decode continues to work just
fine with both rc-6 and rc-5, and now lirc userspace decode shows proper
repeats for both of those protocols as well. Also tested NEC
successfully with both decode options.
We do still need a reset timer callback using the hardware's timeout
value to make sure we actually process samples correctly, regardless of
our somewhat hacky timeout and synthesized trailer above.
This also adds a missing del_timer_sync call to the module unload path.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trying to cap duration before multiplying it was obviously wrong.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already add a trailing space, this wasn't doing anything useful, and
actually confused lirc userspace a bit. Rip it out.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <andrew.vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Microsoft's Windows Media Center specification and requirements doc from
2011.03.18 now refers to the former Power Toggle button as the Sleep
Toggle, and recommends using a new moon sleep icon for it. Its the same
key, but its apparently always been meant to put the system to sleep,
not power it off. Adjust accordingly. While we're here, lets also remove
the duplicate KEY_PLAYPAUSE entry.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
