This is a bug fix for some versions of g200se cards while doing
mode-setting.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
Pull drm fixes from Dave Airlie:
"Just a few straggling fixes I hoovered up, and an intel fixes pull
from Daniel which fixes some regressions, and some mgag200 fixes from
Matrox."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/mgag200: Fix framebuffer base address programming
drm/mgag200: Convert counter delays to jiffies
drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
drm/mgag200: Don't change unrelated registers during modeset
drm: Only print a debug message when the polled connector has changed
drm: Make the HPD status updates debug logs more readable
drm: Use names of ioctls in debug traces
drm: Remove pointless '-' characters from drm_fb_helper documentation
drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
drm: refactor call to request_module
drm: Don't prune modes loudly when a connector is disconnected
drm: Add missing break in the command line mode parsing code
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The original line,
WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
On F19 testing, it was noticed we get a lot of errors in dmesg
about being unable to reserve the buffer when plymouth starts,
this is due to the buffer being in the process of migrating,
so it makes sense we can't reserve it.
In order to deal with it, this adds delayed updates for the dirty
updates, when the bo is unreservable, in the normal console case
this shouldn't ever happen, its just when plymouth or X is
pushing the console bo to system memory.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
These two variables are set again immediately in 'mgag200_modeset_init'
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This change properly enables the "requester" in G200ER cards that is
responsible for getting pixels out of memory and clocking them out to
the screen.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
While testing the mgag200 kms driver on the HP ProLiant Gen8, a
bug was seen. Once the bootloader would load the selected kernel,
the screen would go black. At first it was assumed that the
mgag200 kms driver was hanging. But after setting up the grub
serial output, it was seen that the driver was being loaded
properly. After trying serval monitors, one finaly displayed
the message "Frequency Out of Range". By comparing the kms pll
algorithm with the previous mgag200 xorg driver pll algorithm,
discrepencies were found. Once the kms pll algorithm was
modified, the expected pll values were produced. This fix was
tested on several monitors of varying native resolutions.
Signed-off-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Renesas boards were consistently defaulting to the 1024x768 resolution,
regardless of the native resolution of the monitor plugged in. It was
determined that the EDID of the monitor was not being read. Since the
DAC is a shared line, in order to read from or write to it we must take
control of the DAC clock. This can be done by setting the proper
register to one.
This bug fix sets the register MGA1064_GEN_IO_CTL2 to one. The DAC
control line can be used to determine whether or not a new monitor has
been plugged in. But since the hotplug feature is not one we will
support, it has been decided to simply leave the register set to one.
Signed-off-by: Julia Lemire <jlemire@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A monitor or a user could request a resolution greater than the
available VRAM for the backing framebuffer. This change checks the
required framebuffer size against the max VRAM size and rejects modes
if they are too big. This change can also remove a mode request passed
in via the video= parameter.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
The fb helper lost its support for reallocating an fb completely, so
no need to return special success values any more.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should be done in the drivers for two reasons:
- it gets in the way of fastboot efforts
- it links the fb helpers with the crtc helpers instead of going
through the real interface vfuncs, forcing i915 to fake all the
->disable callbacks used by the crtc helper to avoid ugly Oopsen
v2: Resolve conflicts since drivers still call
drm_fb_helper_single_add_all_connectors.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Dave Airlie <airlied@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have two classes of framebuffer
- Created by the driver (atm only for fbdev), and the driver holds
onto the last reference count until destruction.
- Created by userspace and associated with a given fd. These
framebuffers will be reaped when their assoiciated fb is closed.
Now these two cases are set up differently, the framebuffers are on
different lists and hence destruction needs to clean up different
things. Also, for userspace framebuffers we remove them from any
current usage, whereas for internal framebuffers it is assumed that
the driver has done this already.
Long story short, we need two different ways to cleanup such drivers.
Three functions are involved in total:
- drm_framebuffer_remove: Convenience function which removes the fb
from all active usage and then drops the passed-in reference.
- drm_framebuffer_unregister_private: Will remove driver-private
framebuffers from relevant lists and drop the corresponding
references. Should be called for driver-private framebuffers before
dropping the last reference (or like for a lot of the drivers where
the fbdev is embedded someplace else, before doing the cleanup
manually).
- drm_framebuffer_cleanup: Final cleanup for both classes of fbs,
should be called by the driver's ->destroy callback once the last
reference is gone.
This patch just rolls out the new interfaces and updates all drivers
(by adding calls to drm_framebuffer_unregister_private at all the
right places)- no functional changes yet. Follow-on patches will move
drm core code around and update the lifetime management for
framebuffers, so that we are no longer required to keep framebuffers
alive by locking mode_config.mutex.
I've also updated the kerneldoc already.
vmwgfx seems to again be a bit special, at least I haven't figured out
how the fbdev support in that driver works. It smells like it's
external though.
v2: The i915 driver creates another private framebuffer in the
load-detect code. Adjust its cleanup code, too.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some drivers don't have real ->create_handle callbacks.
- cirrus/ast/mga200: Returns either 0 or -EINVAL.
- udl: Didn't even bother with a callback, leading to a nice
userspace-triggerable OOPS.
- vmwgfx: This driver bothered with an implementation to return 0 as
the handle (which is the canonical no-obj gem handle).
All have in common that ->create_handle doesn't really make too much
sense for them - that ioctl is used only for seamless fb takeover in
the radeon/nouveau/i915 ddx drivers. So allow drivers to not implement
this and return a consistent -ENODEV.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With more fine-grained locking we can no longer rely on the big
mode_config lock to prevent concurrent access to mode resources
like framebuffers. Instead a framebuffer becomes accessible to
other threads as soon as it is added to the relevant lookup
structures. Hence it needs to be fully set up by the time drivers
call drm_framebuffer_init.
This patch here is the drivers part of that reorg. Nothing really fancy
going on safe for three special cases.
- exynos needs to be careful to properly unref all handles.
- nouveau gets a resource leak fixed for free: one of the error
cases didn't cleanup the framebuffer, which is now moot since
the framebuffer is only registered once it is fully set up.
- vmwgfx requires a slight reordering of operations, I'm hoping I didn't
break anything (but it's refcount management only, so should be safe).
v2: Split out exynos, since it's a bit more hairy than expected.
v3: Drop bogus cirrus hunk noticed by Richard Wilbur.
v4: Split out vmwgfx since there's a small change in return values.
Reviewed-by: Rob Clark <rob@ti.com> (core + omapdrm)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All items on the lru list are always reservable, so this is a stupid
thing to keep. Not only that, it is used in a way which would
guarantee deadlocks if it were ever to be set to block on reserve.
This is a lot of churn, but mostly because of the removal of the
argument which can be nested arbitrarily deeply in many places.
No change of code in this patch except removal of the no_wait_reserve
argument, the previous patch removed the use of no_wait_reserve.
v2:
- Warn if -EBUSY is returned on reservation, all objects on the list
should be reservable. Adjusted patch slightly due to conflicts.
v3:
- Focus on no_wait_reserve removal only.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
alloc_apertures() already does the assignment for us, so assigning the
count member after the alloc_apertures() call is not needed.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a memory leak by deallocating the memory we got from
alloc_apertures().
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check for alloc_apertures() memory allocation failure, and propagate an
error code in case the allocation failed.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers set it to 0 and nothing uses it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Remove redundant DRM UAPI header #inclusions from drivers/gpu/.
Remove redundant #inclusions of core DRM UAPI headers (drm.h, drm_mode.h and
drm_sarea.h). They are now #included via drmP.h and drm_crtc.h via a preceding
patch.
Without this patch and the patch to make include the UAPI headers from the core
headers, after the UAPI split, the DRM C sources cannot find these UAPI headers
because the DRM code relies on specific -I flags to make #include "..." work
on headers in include/drm/ - but that does not work after the UAPI split without
adding more -I flags.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of the DRM drivers appear to be missing the .compat_ioctl file
operation entry necessary for 32-bit application compatibility.
This patch uses drm_compat_ioctl for all drivers which don't have
their own, and which are using drm_ioctl for .unlocked_ioctl.
This leaves drivers/gpu/drm/psb/psb_drv.c unchanged; it has a custom
.unlocked_ioctl and will presumably need a custom .compat_ioctl as
well.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Neither the drm core nor any of the drivers really need the raw_edid field
of struct drm_display_info for anything. Instead of being useful, it
creates confusion about who is responsible for freeing the memory it points
to and setting the field to NULL afterwards, leading to memory leaks and
dangling pointers.
Remove the raw_edid field, and fix drivers as necessary.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The original code was misported from the X driver,
a) an int went to unsigned int, breaking the downward counting testm code
b) the port did the vco/computed clock bits completely wrong.
This fixes an infinite loop on modprobe on some Dell servers with the G200ER
chipset variant.
Found in internal testing.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
we are referencing the pointer after doing alloc_apertures,
as alloc_apertures kzallocs, the kzalloc may fail and we get a NULL.
so we need to check for NULL before we dereference this pointer
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The passed mode must not be modified by the operation, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It appears grub2 can pass framebuffer info via efifb, so
we need to kick it off earlier to reserve the vram allocation.
(just a fixup same as for cirrus)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a driver for the G200 server engines chips,
it doesn't driver any of the Matrix G series desktop cards.
It will bind to G200 SE A,B, G200EV, G200WB, G200EH and G200ER cards.
Its based on previous work done my Matthew Garrett but remodelled
to follow the same style and flow as the AST server driver. It also
works along the same lines as the AST server driver wrt memory management.
There is no userspace driver planned, xf86-video-modesetting should be used.
It also appears these GPUs have no ARGB hw cursors.
v2: add missing tagfifo reset + G200 SE memory bw setup pieces.
Signed-off-by: Dave Airlie <airlied@redhat.com>
