In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.
Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.
Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.
v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inspired by a recent regression that seems to confuse pch transcoder
state, let's be a bit more paranoid.
References: https://bugs.freedesktop.org/show_bug.cgi?id=49712
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Pimped commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables i915 driver to handle Haswell devices. It should go in
last, when things are working stable enough.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.
Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.
This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_hdmi data structure and support functions to a shared location,
to allow their usage from intel_ddi module.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This table is used for programming WR PLL clocks, used by HDMI and DVI outputs.
I split it into a separate patch to simplify the HDMI enabling patch which was
getting huge.
Note that this table is a temporary solution for WR PLL programming. It
will be reworked into a more exact algorithm at a later stage. But for
now, it provides the most accurate clock setting solution, so we use it
here.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those are driven by DDIs on Haswell architecture, so we need to keep track
of which DDI is being used on each output.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Digital port detection on Haswell is indicated by the presence of a bit in
DDI_BUF_CTL for port A, and by a different register for ports B, C and D.
So we check for those bits during the initialization time and let the hdmi
function know about those.
Note that this bit does not indicates whether the output is DP or HDMI.
However, the DDI buffers can be programmed in a way that is shared between
DP/HDMI and FDI/HDMI except for PORT E.
So for now, we detect those digital outputs as being HDMI, but proper DP
support is still pending.
Note that DDI A can only drive eDP, so we do not handle it here for hdmi
initialization.
v2: simplify Haswell handling logic
v3: use generic function for handling digital outputs.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The iCLKIP clock is used to drive the VGA pixel clock on the PCH. In order
to do so, it must be programmed to properly do the clock ticks according
to the divisor, phase direction, phase increments and a special auxiliary
divisor for 20MHz clock.
v2: calculate divisor values directly instead of relying on a table.
v3: merged a fix from Ben to properly check for invalid divider values.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The line time can be programmed according to the number of horizontal
pixels vs effective pixel rate ratio.
v2: improve comment as per Chris Wilson suggestion
v3: incorporate latest changes in specs.
v4: move into wm update routine, also mention that the same routine can
program IPS watermarks. We do not have their enablement code yet, nor
handle the required clock settings at the moment, so this patch won't
program those values for now.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, we simple reuse the Ivy Bridge routines here.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with Haswell, DDI ports can work in FDI mode to support
connectivity with the outputs located on the PCH.
This commit adds support for such connections in the intel_ddi module, and
provides Haswell-specific functionality to make it work.
v2: simplify the commit as per Daniel Vetter suggestion.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DDI is introduced starting with Haswell GPU generation. So to simplify its
management in the future, we also add intel_ddi.c to hold all the
DDI-related items.
Buffer translations for DDI links must be initialized prior to enablement.
For FDI and DP, first 9 pairs of values are used to select the connection
parameters. HDMI uses the last pair of values and ignores the first 9
pairs. So we program HDMI values in both cases, which allows HDMI to work
over both FDI and DP-friendly buffers.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, only one pipe can work in FDI mode, so this patch prevents
messing with wrong registers when FDI is being used by non-first pipe. And
to prevent this, we also specify that the VGA can only be used on pipe 0
for now in the crtc_mask value.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent bogus asserts on DDI-related paths.
Longer explanation from Eugeni by mail:
"For the asserts there are 3 paths where we hit them:
- in assert_fdi_tx (we don't have the FDI_TX_CTL anymore, backup plan
DDI_FUNC_CTL is used instead)
- in assert_fdi_tx_pll_enabled (we have the combination of iCLKIP and
DDI_FUNC_CTL, plus PORT_CLK_SEL and PIPE_CLK_SEL now to make things
work). We could use an assert here indeed - if we configure port to
use one clock, and pipe to use another, everything hangs. Right now,
we configure all of them in one place only; but yes, when DP code
lands it will get more funky.
- and in ironlake_fdi_pll_enable. I reuse part of this function (to
configure the TU sizes), but as in the 1st case, FDI_TX_CTL is gone
so I just ignore it here."
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Pasted Eugeni's explanation into the commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This attempts to enable all the available power wells during the
initialization.
Those power wells can be enabled in parallel or on-demand, and disabled
when no longer needed, but this is out of scope of this initial
enablement. Proper tracking of who uses which power well will require
a considerable rework of our display handling, so we just leave them all
enabled when the driver is loaded for now.
v2: use more generic and future-proof code
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, the recommended PCH-connected output is the one driven by DDI
E in FDI mode, used for VGA connection. All the others are handled by the
CPU.
Note that this does not accounts for Haswell/PPT combination yet, so if we
encounter such combination an error message is thrown to indicate that
things could go wrong.
v2: improve non-LPT detection warning per Daniel Vetter's suggestion.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should be already configured when FDI auto-negotiation is done.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will throw a BUG() message when an unknown sdvox register is
given to intel_hdmi_init. When this happens, things could going to be pretty
much broken afterwards, so we better detect this as soon as possible.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As suggested by Chris Wilson and Daniel Vetter, this chunk of code can be
simplified with a more simple check.
Also, as noticed by Jesse Barnes, it is worth mentioning that plane is an
enum and num_pipe is an int, so we could be more paranoid here about those
validation checks eventually.
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds proper support for calculating those watermarks, checking for
number of available pipes instead of specific GPU variants when deciding
if watermarks for 3rd pipe are necessary.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With Lynx Point, we need to use SBI to communicate with the display clock
control. This commit adds helper functions to access the registers via
SBI.
v2: de-inline the function and address changes in bits names
v3: protect operations with dpio_lock, increase timeout to 100 for
paranoia sake.
v4: decrease paranoia a bit, as noticed by Chris Wilson
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell interrupts are mostly similar with Ivy Bridge, so we share same
routines with it.
This patch also simplifies the vblank counter handling for all the Gen5+
architectures.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell has different DIP control registers and offsets which we need to
use for infoframes, which this patch adds.
Note that this does not adds full DIP frames support, but only the basic
functionality necessary for HDMI to work in early enablement.
v2: replace infoframe handling with a debug message, proper support will
be added via a patch from Paulo Zanoni later.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we call gen6_enable_rps() (which writes into the per-ring
register mmio space) from intel_modeset_init_hw() which is called before
we initialise the rings. If we defer intel_modeset_init_hw() until
afterwards (in the intel_modeset_gem_init() phase) all is well.
v2: Rectify ordering of gem vs display HW init upon resume. (Daniel)
v3: Fix up locking. (Paulo)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Smash Paulo's locking fix onto Chris' patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can take advantage that the PCH_IIR is a subordinate register to
reduce one of the required IIR reads, and that we only need to clear
interrupts handled to reduce the writes. And by simply tidying the code
we can reduce the line count and hopefully make it more readable.
v2: Split out the bugfix from the refactoring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inspired by the recent ppgtt regression report, where switching of
dmar only for the gpu seems to fix things completely, I've looked
again at the semaphores+vt-d situation.
Contrary to my earlier testing a few months back my system is now
stable with dmar disabled for the igd, and not only when disabling
dmar completely.
So I'm rather hopeful that all our recent fixes for snb have changed
things for code and it's time to try enabling semaphores again. We've
also had issues with enabling semaphores which are not vt-d related,
but I guess these are all fixed by the autoreport-disabling and lazy
request fix. And there's only one way to find out whether there are
still other issues ...
When I've tried to apply this patch I've noticed that semaphores on
gen6 have already silently been enabled in
commit 2911a35b2e
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Thu Apr 5 14:47:36 2012 -0700
drm/i915: use semaphores for the display plane
Fix this up by only checking whether dmar is enabled on the gfx (not
on the entire system).
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... given that I essentially run the show already, let's make this
official.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two functions are actually hw-specific and only valid for gm45
thru gen7. HSW completely changes how this works, so label them
accordingly.
v2: s/gm45/g4x/ like for the previous patch.
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Generally we call stuff with i9xx_ when it's valid for gen3+. But
gen3 and early gen4 only support hdmi with sdvo cards, and writing
infoframes works completely different there.
v2: Use g4x instead of gm45 - it applies to the desktop variant, too.
v3: Properly align the paramters of g4x_write_infoframe again, noticed
by Paulo Zanoni.
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simplifies things because for all the infoframes we care about,
we always send them on each vblank. Also, this gets rid of one
of the hw specific functions mislabelled with the intel_ prefix -
hsw will completely change how this works!
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The principle of intel_mark_busy() is that we want to spot the
transition of when the display engine is being used in order to bump
powersaving modes and increase display clocks. As such it is only
important when the display is changing, i.e. when rendering to the
scanout or other sprite/plane, and these are characterised by being
pinned.
v2: Mark the whole device as busy on execbuffer and pageflips as well
and rebase against dinq for the minor bug fix to be immediately
applicable.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: fix compile fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_wait_for_vblank uses PIPESTAT, which does not exist on Ironlake
and newer, so now we use PIPEFRAME.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Ditch the check for disable pipe from the new ilk wait for
vblank function to keep it consisten with existing behaviour.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like Gen 4, IBX has a "Port Select" field on the DIP register,
but the ports are different.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IBX does not need the workaround used in cpt_write_infoframe that
requires the AVI frame to be enabled while being updated.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The registers are on the PCH, so use the PCH name instead of the CPU
name. Also, the way this function is implemented is really only for
CPT and PPT. For now, both functions have the same implementations:
the next patch will fix ibx_write_infoframe.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Better safe than sorry. Currently we never change the frequency and
use the same for every infoframe type, so the only way to reproduce a
bug would be with the BIOS doing something.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's what the VIDEO_DIP_CTL documentation says we need to do. Except
when it's the AVI InfoFrame and we're ironlake_write_infoframe.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will allow us to disable an infoframe without changing its
frequency.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should prevent bugs when changing the port.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we're doing the right thing, just like we do on gen5+.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't use intermediate variables, change the value of 'val' as we go
through the function. The new style looks more similar to the rest of
our code. IMHO, it's also easier to read and change.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen3+ is 13 bits (12:0), and on gen2 only 12 (11:0). For both the high
bits are marked reserved, read-only so continue to mask them. Bit 31
is not reserved and has a meaning.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge of drm-next to resolve a few ugly conflicts and to get a few
fixes from 3.4-rc6 (which drm-next has already merged). Note that this
merge also restricts the stencil cache lra evict policy workaround to
snb (as it should) - I had to frob the code anyway because the
CM0_MASK_SHIFT define died in the masked bit cleanups.
We need the backmerge to get Paulo Zanoni's infoframe regression fix
for gm45 - further bugfixes from him touch the same area and would
needlessly conflict.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
