If hlid was already removed, there is no need to remove
its key (it might cause a fw crash, as the key is invalid).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After adding a station, call wl12xx_cmd_set_peer_state().
This is required for 11n support.
Change wl12xx_cmd_set_peer_state() prototype to get hlid
as param.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Incorporate interface changes for HT support.
Add ba_bitmap field to the wl1271_link struct, to indicate
activate RX BA sessions (for AP mode).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Using hlid=0 in AP mode is a bug. Dynamically allocate HLIDs.
Set the "first sta hlid" as 3. This will have to be changed
when multiple vifs will be supported.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The BT coex params api have been changed.
Update it, and init coex for both sta and ap.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The ROC command asks the fw stay on the channel of the given
hlid. it currently has 2 primary functions:
1. Allow tx/rx from the device role.
In order to tx/rx packets while the stations is not associated
(e.g. auth req/resp), the device role has to be used, along
with ROC on its link.
Keep the logic similiar to the one used in dummy_join. However,
since we can't scan while we ROC, we add CROC before starting
a scan, and ROC again (if needed) on scan complete.
2. Keeping the antenna for a specific link.
We ROC until the connection was completed (after EAPOLs exchange)
in order to prevent BT coex operations from taking the antenna
and failing the connection (after this stage, psm can be used).
During association, we ROC on the station role, and then CROC
the device role, thus assuring being ROC during all the connection
process.
Delete the WL1271_FLAG_JOINED flag, and use a roc bitmap
to indicate what roles are currently ROCed.
Add wl12xx_roc/croc functions in order to wrap the roc/croc
commands while taking care of the roc bitmap.
The current ROC/CROC state-machine is a bit complicated. In
the future we'll probably want to use wpa_supplicant to control
the ROC during connection.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow handling of DUMMY_PACKET_EVENT_ID also in ap mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add structs and functions to support the ROC/CROC commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
system_hlid is a const hlid (always 0), used by the fw and driver
for packets which are not bound to specific role (e.g. dynamic
memory packets).
indicate it as always allocated.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use ACX_BEACON_FILTER_OPT for both station and ap roles
(use the generic wl1271_acx_beacon_filter_opt()
instead of wl1271_acx_set_ap_beacon_filter() ).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The max template size was increased in the new fw.
However, we should use the max size only when needed, as it
consumes some of the chip's memory.
Thus, by default initialize the templates to the default size.
Initialize to the maximum size only when required.
Use WL1271_CMD_TEMPL_DFLT_SIZE instead of some of the
predefined structs, as some of them didn't account
for additional IEs that might be added to the template.
Delete structs defintions not used after these changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the rx/tx descriptors according to the new fw api
(fw >= 6/7.3.0.0.75)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the scan command to use the new fw api
(fw 6/7.3.0.0.75).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The device role is a special role used for rx and tx frames
prior to association (as the STA role can get packets only
from its associated bssid)
Since this role is required for the sta association process,
we enable it when a new sta interface is created.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
According to the new multi-role flow, we have to enable the
role before using (starting) it, and disable it on cleanup
(after it's no longer needed).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Change the commands and events according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change is the replacement of JOIN/DISCONNECT commands,
with ROLE_START/ROLE_STOP commands.
The use of these commands should be preceded by the ROLE_ENABLE
command (allocating role resources), and followed by the
ROLE_DISABLE command (freeing role resources).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the acx commands according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change in most of the ACXs is the addition
of a new role_id/link_id field, which is required
for multi-role operation.
Currently, we don't really support multi-role, as
most of our data (inside wl) is global.
As the current fw doesn't support concurrent roles
yet, keep it this way and add wl->role_id and
wl->sta_hlid to save the active role/link.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the fw status struct according to the new fw api
(fw >= 6/7.0.0.35).
All the roles use the same struct now.
The memory accounting was changed a bit according to
the struct changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw doesn't support rx_filtering configuration (as a
stand-alone command. the rx filtering is done automatically
according to the active role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to keep to driver compiling during the patchset,
while avoiding one-huge-patch, temporarily disable some
advanced ap functions.
These changes will be reverted later in the patchset, as
part of the patches for advanced ap functions support.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This does not make sense in fw >= 6/7.3.0.0.75 (wl127x/wl128x) -
we don't use Tx blocks to measure FW occupancy anymore.
This reverts commit 9e374a37b6.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the value of PG version for 128x at sysfs, remove write permissions
from PG version (hw_pg_ver) in sysfs and add remove files
(hw_pg_ver,bt_coex_state) from sysfs while freeing hardware.
New macro names for register Fuse_data_2_1 depend on architecture.
Propagate chip id through wiphy in PLT mode which still not work of
a bug in ethtool.
Signed-off-by: Gery Kahn <geryk@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In case of QoS packets the packet payload isn't aligned to
4 bytes. In that case the mac80211 layer take care of that
via memmove() in ieee80211_deliver_skb().
Add support of copy packets from aggregation buffer to the
skbs with packet payload aligned care. In case of QoS packets
copy the packets in offset of 2 bytes guarantee payload aligned
to 4 bytes.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
the comments are obselete as the virtual wiphy support was removed from
the driver
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the ease of debugging, we display only the rate control statistics
for currently operating mode and bandwidth
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_FLAG_HT must be included when reporting MCS rates. Without
this, mac80211 ended up dropping any frame sent at MCS index 12
or higher and that resulted in oddly random looking errors in
mac80211_hwsim tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here
To fix this add ath6kl prefix to all public functions in htc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since kernel 3.0, the problems with controlling b43 devices that have
low-power (LP) PHYs have been fixed and the EXPERIMENTAL designation
can be fixed.
This patch also fixes a typo as the device supports 802.11b communications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always hit the goto and skip the printk(). The original code does
the right thing even though it looks messy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.
Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.
While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the driver no longer uses the raw r/w routines, remove their definitions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe driver used raw reads and writes on the PCIe hardware.
As all of these are only affecting the configuration space, all of
then can be converted to pci_{read,write}_config_XX calls.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add code to display driver version information in dmesg after
loading the driver successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO card is now fully powered down when the network interface is
brought down.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the driver so that it does not function when the interface is
down, in preparation for runtime power management.
No commands can be run while the interface is down, so the ndo_dev_stop
routine now directly does all necessary work (including asking the device
to disconnect from the network and disabling multicast functionality)
directly.
power_save and power_restore hooks are added meaning that card drivers
can take steps to turn the device off when the interface is down.
The MAC address can now only be changed when all interfaces are down;
the new address will be programmed when an interface gets brought up.
This matches mac80211 behaviour.
Also, some small cleanups/simplifications were made in the surrounding
device handling logic.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
