STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a new compatible string for stmpe mfd to support
stmpe1600 variant.
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset
This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.
For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to prepare the ground to STMPE1600,
as STMPE1600's SYS_CTRL register has the same layout as
STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI
bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On STMPE801/1801 datasheets, it's mentionned writing
in interrupt status register has no effect, bits are
cleared when reading.
Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
By cross-checking STMPE 610/801/811/1601/2401/2403 datasheets,
it appears that edge detection and rising/falling edge detection
is not supported by all STMPE variant:
GPIO GPIO
Edge detection rising/falling
edge detection
610 | X | X |
801 | | |
811 | X | X |
1600 | | |
1601 | X | X |
1801 | | X |
2401 | X | X |
2403 | X | X |
Rework stmpe_dbg_show_one() and stmpe_gpio_irq to correctly
take these cases into account.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reset was only implemented for STMPE1801 variant despite
all variant have a SOFT_RESET bit.
For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7
of SYS_CTRL register.
For STMPE610/811 (which have the same variant id) SOFT_RESET
bit is bit 1 of SYS_CTRL register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly
This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 8d460f6156 ("powerpc/process: Add the function
flush_tmregs_to_thread") added flush_tmregs_to_thread() and included
the assumption that it would only be called for a task which is not
current.
Although this is correct for ptrace, when generating a core dump, some
of the routines which call flush_tmregs_to_thread() are called. This
leads to a WARNing such as:
Not expecting ptrace on self: TM regs may be incorrect
------------[ cut here ]------------
WARNING: CPU: 123 PID: 7727 at arch/powerpc/kernel/process.c:1088 flush_tmregs_to_thread+0x78/0x80
CPU: 123 PID: 7727 Comm: libvirtd Not tainted 4.8.0-rc1-gcc6x-g61e8a0d #1
task: c000000fe631b600 task.stack: c000000fe63b0000
NIP: c00000000001a1a8 LR: c00000000001a1a4 CTR: c000000000717780
REGS: c000000fe63b3420 TRAP: 0700 Not tainted (4.8.0-rc1-gcc6x-g61e8a0d)
MSR: 900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28004222 XER: 20000000
...
NIP [c00000000001a1a8] flush_tmregs_to_thread+0x78/0x80
LR [c00000000001a1a4] flush_tmregs_to_thread+0x74/0x80
Call Trace:
flush_tmregs_to_thread+0x74/0x80 (unreliable)
vsr_get+0x64/0x1a0
elf_core_dump+0x604/0x1430
do_coredump+0x5fc/0x1200
get_signal+0x398/0x740
do_signal+0x54/0x2b0
do_notify_resume+0x98/0xb0
ret_from_except_lite+0x70/0x74
So fix flush_tmregs_to_thread() to detect the case where it is called on
current, and a transaction is active, and in that case flush the TM regs
to the thread_struct.
This patch also moves flush_tmregs_to_thread() into ptrace.c as it is
only called from that file.
Fixes: 8d460f6156 ("powerpc/process: Add the function flush_tmregs_to_thread")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 7aef413656 ("powerpc32: rewrite csum_partial_copy_generic()
based on copy_tofrom_user()") introduced a bug when destination
address is odd and initial csum is not null
In that (rare) case the initial csum value has to be rotated one byte
as well as the resulting value is
This patch also fixes related comments
Fixes: 7aef413656 ("powerpc32: rewrite csum_partial_copy_generic() based on copy_tofrom_user()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch the setting of psl_fir_cntl from debug to production
environment recommended value. It mostly affects the PSL behavior when
an error is raised in psl_fir1/2.
Tested with cxlflash.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I've found funny live-lock between raid10 barriers during resync and
memory controller hard limits. Inside mpage_readpages() task holds on to
its plug bio which blocks the barrier in raid10. Its memory cgroup have
no free memory thus the task goes into reclaimer but all reclaimable
pages are dirty and cannot be written because raid10 is rebuilding and
stuck on the barrier.
Common flush of such IO in schedule() never happens, because the caller
doesn't go to sleep.
Lock is 'live' because changing memory limit or killing tasks which
holds that stuck bio unblock whole progress.
That was what happened in 3.18.x but I see no difference in upstream
logic. Theoretically this might happen even without memory cgroup.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@fb.com>
User visible fixes:
- Fix the lookup for a kernel module in 'perf probe', fixing for instance, the
erroneous return of "[raid10]" when looking for "[raid1]" (Konstantin Khlebnikov)
- Disable counters in a group before reading them in 'perf stat', to avoid skew (Mark Rutland)
- Fix adding probes to function aliases in systems using kaslr (Masami Hiramatsu)
- Trip libtraceevent trace_seq buffers, removing unnecessary memory usage that could
bring a system using tracepoint events with 'perf top' to a crawl, as the trace_seq
buffers start at a whooping 4 KB, which is very rarely used in perf's usecases,
so realloc it to the really used space as a last measure after using libtraceevent
functions to format the fields of tracepoint events (Arnaldo Carvalho de Melo)
- Fix 'perf probe' location when using DWARF on ppc64le (Ravi Bangoria)
Improvement:
- Allow specifying signedness casts to a 'perf probe' variable, to shorten
the number of steps to see signed values that otherwise would always appear
as hex values (Naohiro Aota)
Documentation fixes:
- Add 'bpf-output' field to 'perf script' usage message (Brendan Gregg)
Infrastructure fixes:
- Sync kernel header files: cpufeatures.h, {disabled,required}-features.h,
bpf.h and vmx.h, so that we get a clean build, without warnings about files
being different from the kernel counterparts.
A verification of the need or desirability of changes in tools/ based on what
was done in the kernel changesets was made and documented in the respective
file sync changesets (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/B7T
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-20160809' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
User visible fixes:
- Fix the lookup for a kernel module in 'perf probe', fixing for instance, the
erroneous return of "[raid10]" when looking for "[raid1]" (Konstantin Khlebnikov)
- Disable counters in a group before reading them in 'perf stat', to avoid skew (Mark Rutland)
- Fix adding probes to function aliases in systems using kaslr (Masami Hiramatsu)
- Trip libtraceevent trace_seq buffers, removing unnecessary memory usage that could
bring a system using tracepoint events with 'perf top' to a crawl, as the trace_seq
buffers start at a whooping 4 KB, which is very rarely used in perf's usecases,
so realloc it to the really used space as a last measure after using libtraceevent
functions to format the fields of tracepoint events (Arnaldo Carvalho de Melo)
- Fix 'perf probe' location when using DWARF on ppc64le (Ravi Bangoria)
- Allow specifying signedness casts to a 'perf probe' variable, to shorten
the number of steps to see signed values that otherwise would always appear
as hex values (Naohiro Aota)
Documentation fixes:
- Add 'bpf-output' field to 'perf script' usage message (Brendan Gregg)
Infrastructure fixes:
- Sync kernel header files: cpufeatures.h, {disabled,required}-features.h,
bpf.h and vmx.h, so that we get a clean build, without warnings about files
being different from the kernel counterparts.
A verification of the need or desirability of changes in tools/ based on what
was done in the kernel changesets was made and documented in the respective
file sync changesets (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit 874f9c7da9.
Geert Uytterhoeven reports:
"This change seems to have an (unintendent?) side-effect.
Before, pr_*() calls without a trailing newline characters would be
printed with a newline character appended, both on the console and in
the output of the dmesg command.
After this commit, no new line character is appended, and the output
of the next pr_*() call of the same type may be appended, like in:
- Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000
- Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)
+ Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)"
Joe Perches says:
"No, that is not intentional.
The newline handling code inside vprintk_emit is a bit involved and
for now I suggest a revert until this has all the same behavior as
earlier"
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Requested-by: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
properly by the tracing user space tools. This was due to the
TRACE_DEFINE_ENUM() being set to a define, when it should have been set
to the enum itself. The define was of the MASK that used the BIT to shift.
The BIT was the enum and by adding that, everything gets converted nicely.
The MASK is still kept just in case it gets converted to an enum in the
future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXqeA/AAoJEKKk/i67LK/8wLAH/0nD8L5pxtn+pZi3mQnWNwbn
qEBtfKK8cvnt0IWH2HlKmRKLAiIJfp8UrkGoPiLT7Nb83PlKaw3UT868t7eDmknu
b29SsZroMgvJ1MeeNH9Yzk7cK3/K213VO02P4ce8EWSELYCqFlxJDE3dhl52K9Lj
clJSoZbIGTLlx4pk6zZnPksTt3Z9WZXcVJITwxEiz/Cr+CKAWZpLoPPUaqJOmA4j
9oS6d++0DYZdz3cWCmYBBkphmc5IQkBNZWGMYLcAR+M+m5fsN+baWlP3Dhq4j7he
WknHwu4WDFMk6a2Kh0Ggi6yUWVUIkLNY2Z4QUF2gNmJT1g/FH5lZka4/kIxjvKw=
=rgBA
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix tick_stop tracepoint symbols for user export.
Luiz Capitulino noticed that the tick_stop tracepoint wasn't being
parsed properly by the tracing user space tools.
This was due to the TRACE_DEFINE_ENUM() being set to a define, when it
should have been set to the enum itself. The define was of the MASK
that used the BIT to shift. The BIT was the enum and by adding that,
everything gets converted nicely. The MASK is still kept just in case
it gets converted to an enum in the future"
* tag 'trace-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix tick_stop tracepoint symbols for user export
- Fixes a problem with gcc plugins interfering with cc-option tests.
- Aborts more gracefully when gcc plugin headers or compiler support is
missing.
- Improves the gcc plugin rule generation to be more dynamic, pass arguments,
and build from subdirectories.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=Jwmy
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugin-infrastructure-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin improvements from Kees Cook:
"Several fixes/improvements for the gcc plugin infrastructure:
- fix a problem with gcc plugins interfering with cc-option tests.
- abort more gracefully when gcc plugin headers or compiler support
is missing.
- improve the gcc plugin rule generation to be more dynamic, pass
arguments, and build from subdirectories"
* tag 'gcc-plugin-infrastructure-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Add support for plugin subdirectories
gcc-plugins: Automate make rule generation
gcc-plugins: Add support for passing plugin arguments
gcc-plugins: abort builds cleanly when not supported
kbuild: no gcc-plugins during cc-option tests
Pull drm fixes from Dave Airlie:
"This contains a bunch of amdgpu fixes, and some i915 regression fixes.
It also contains some fixes for an older regression with some EDID
changes and some 6bpc panels.
Then there are the lockdep, cirrus and rcar-du regression fixes from
this window"
* tag 'drm-fixes-for-4.8-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/cirrus: Fix NULL pointer dereference when registering the fbdev
drm/edid: Set 8 bpc color depth for displays with "DFP 1.x compliant TMDS".
drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"
drm/edid: Add 6 bpc quirk for display AEO model 0.
drm: Paper over locking inversion after registration rework
drm: rcar-du: Link HDMI encoder with bridge
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/i915/fbdev: Check for the framebuffer before use
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
Commit b195d5e2bf ("ipr: Wait to do async scan until scsi host is
initialized") fixed async scan for ipr, but broke sync scan for ipr.
This fixes sync scan back up.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To distinguish non-slab pages charged to kmemcg we mark them PageKmemcg,
which sets page->_mapcount to -512. Currently, we set/clear PageKmemcg
in __alloc_pages_nodemask()/free_pages_prepare() for any page allocated
with __GFP_ACCOUNT, including those that aren't actually charged to any
cgroup, i.e. allocated from the root cgroup context. To avoid overhead
in case cgroups are not used, we only do that if memcg_kmem_enabled() is
true. The latter is set iff there are kmem-enabled memory cgroups
(online or offline). The root cgroup is not considered kmem-enabled.
As a result, if a page is allocated with __GFP_ACCOUNT for the root
cgroup when there are kmem-enabled memory cgroups and is freed after all
kmem-enabled memory cgroups were removed, e.g.
# no memory cgroups has been created yet, create one
mkdir /sys/fs/cgroup/memory/test
# run something allocating pages with __GFP_ACCOUNT, e.g.
# a program using pipe
dmesg | tail
# remove the memory cgroup
rmdir /sys/fs/cgroup/memory/test
we'll get bad page state bug complaining about page->_mapcount != -1:
BUG: Bad page state in process swapper/0 pfn:1fd945c
page:ffffea007f651700 count:0 mapcount:-511 mapping: (null) index:0x0
flags: 0x1000000000000000()
To avoid that, let's mark with PageKmemcg only those pages that are
actually charged to and hence pin a non-root memory cgroup.
Fixes: 4949148ad4 ("mm: charge/uncharge kmemcg from generic page allocator paths")
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch 19a469a587 ("drivers/perf: arm-pmu: Handle per-interrupt
affinity mask") added support for partitionned PPI setups, but
inadvertently broke setups using SPIs without the "interrupt-affinity"
property (which is the case for UP platforms).
This patch restore the broken functionnality by testing whether the
interrupt is percpu or not instead of relying on the using_spi flag
that really means "SPI *and* interrupt-affinity property".
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 19a469a587 ("drivers/perf: arm-pmu: Handle per-interrupt affinity mask")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
arm_pmu_mutex is never held long and we don't want to sleep while the
lock is being held as it's executed in the context of hotplug notifiers.
So it can be converted to a simple spinlock instead.
Without this patch we get the following warning:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/2
no locks held by swapper/2/0.
irq event stamp: 381314
hardirqs last enabled at (381313): _raw_spin_unlock_irqrestore+0x7c/0x88
hardirqs last disabled at (381314): cpu_die+0x28/0x48
softirqs last enabled at (381294): _local_bh_enable+0x28/0x50
softirqs last disabled at (381293): irq_enter+0x58/0x78
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.7.0 #12
Call trace:
dump_backtrace+0x0/0x220
show_stack+0x24/0x30
dump_stack+0xb4/0xf0
___might_sleep+0x1d8/0x1f0
__might_sleep+0x5c/0x98
mutex_lock_nested+0x54/0x400
arm_perf_starting_cpu+0x34/0xb0
cpuhp_invoke_callback+0x88/0x3d8
notify_cpu_starting+0x78/0x98
secondary_start_kernel+0x108/0x1a8
This patch converts the mutex to spinlock to eliminate the above
warnings. This constraints pmu->reset to be non-blocking call which is
the case with all the ARM PMU backends.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Fixes: 37b502f121 ("arm/perf: Fix hotplug state machine conversion")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
pathbase is the base inode; set it to 0 if we've got no path.
Coverity-id: 146348
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
ceph_file_layout::pool_id is now s64. rbd_add_get_pool_id() and
ceph_pg_poolid_by_name() both return an int, so it's bogus anyway.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Powerpc has Global Entry Point and Local Entry Point for functions. LEP
catches call from both the GEP and the LEP. Symbol table of ELF contains
GEP and Offset from which we can calculate LEP, but debuginfo does not
have LEP info.
Currently, perf prioritize symbol table over dwarf to probe on LEP for
ppc64le. But when user tries to probe with function parameter, we fall
back to using dwarf(i.e. GEP) and when function called via LEP, probe
will never hit.
For example:
$ objdump -d vmlinux
...
do_sys_open():
c0000000002eb4a0: e8 00 4c 3c addis r2,r12,232
c0000000002eb4a4: 60 00 42 38 addi r2,r2,96
c0000000002eb4a8: a6 02 08 7c mflr r0
c0000000002eb4ac: d0 ff 41 fb std r26,-48(r1)
$ sudo ./perf probe do_sys_open
$ sudo cat /sys/kernel/debug/tracing/kprobe_events
p:probe/do_sys_open _text+3060904
$ sudo ./perf probe 'do_sys_open filename:string'
$ sudo cat /sys/kernel/debug/tracing/kprobe_events
p:probe/do_sys_open _text+3060896 filename_string=+0(%gpr4):string
For second case, perf probed on GEP. So when function will be called via
LEP, probe won't hit.
$ sudo ./perf record -a -e probe:do_sys_open ls
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.195 MB perf.data ]
To resolve this issue, let's not prioritize symbol table, let perf
decide what it wants to use. Perf is already converting GEP to LEP when
it uses symbol table. When perf uses debuginfo, let it find LEP offset
form symbol table. This way we fall back to probe on LEP for all cases.
After patch:
$ sudo ./perf probe 'do_sys_open filename:string'
$ sudo cat /sys/kernel/debug/tracing/kprobe_events
p:probe/do_sys_open _text+3060904 filename_string=+0(%gpr4):string
$ sudo ./perf record -a -e probe:do_sys_open ls
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.197 MB perf.data (11 samples) ]
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1470723805-5081-2-git-send-email-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Instead of inline code, introduce function to post process kernel
probe trace events.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1470723805-5081-1-git-send-email-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Due to:
1e61f78baf ("x86/cpufeature: Make sure DISABLED/REQUIRED macros are updated")
No changes to tools using those headers (tools/arch/x86/lib/mem{set,cpu}_64.S)
seems necessary.
Detected by the tools build header drift checker:
$ make -C tools/perf O=/tmp/build/perf
make: Entering directory '/home/acme/git/linux/tools/perf'
BUILD: Doing 'make -j4' parallel build
GEN /tmp/build/perf/common-cmds.h
Warning: tools/arch/x86/include/asm/disabled-features.h differs from kernel
Warning: tools/arch/x86/include/asm/required-features.h differs from kernel
Warning: tools/arch/x86/include/asm/cpufeatures.h differs from kernel
CC /tmp/build/perf/util/probe-finder.o
CC /tmp/build/perf/builtin-help.o
<SNIP>
^C$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-ja75m7zk8j0jkzmrv16i5ehw@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The way we're using kernel headers in tools/ now, with a copy that is
made to the same path prefixed by "tools/" plus checking if that copy
got stale, i.e. if the kernel counterpart changed, helps in keeping
track with new features that may be useful for tools to exploit.
For instance, looking at all the changes to bpf.h since it was last
copied to tools/include brings this to toolers' attention:
Need to investigate this one to check how to run a program via perf, setting up
a BPF event, that will take advantage of the way perf already calls clang/LLVM,
sets up the event and runs the workload in a single command line, helping in
debugging such semi cooperative programs:
96ae522795 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers")
This one needs further investigation about using the feature it improves
in 'perf trace' to do some tcpdumpin' mixed with syscalls, tracepoints,
probe points, callgraphs, etc:
555c8a8623 ("bpf: avoid stack copy and use skb ctx for event output")
Add tracing just packets that are related to some container to that mix:
4a482f34af ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
4ed8ec521e ("cgroup: bpf: Add BPF_MAP_TYPE_CGROUP_ARRAY")
Definetely needs to have example programs accessing task_struct from a bpf proggie
started from 'perf trace':
606274c5ab ("bpf: introduce bpf_get_current_task() helper")
Core networking related, XDP:
6ce96ca348 ("bpf: add XDP_TX xdp_action for direct forwarding")
6a773a15a1 ("bpf: add XDP prog type for early driver filter")
13c5c240f7 ("bpf: add bpf_get_hash_recalc helper")
d2485c4242 ("bpf: add bpf_skb_change_type helper")
6578171a7f ("bpf: add bpf_skb_change_proto helper")
Changes detected by the tools build system:
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/home/acme/git/linux/tools/perf'
BUILD: Doing 'make -j4' parallel build
Warning: tools/include/uapi/linux/bpf.h differs from kernel
INSTALL GTK UI
CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o
<SNIP>
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Brenden Blanco <bblanco@plumgrid.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Sargun Dhillon <sargun@sargun.me>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-difq4ts1xvww6eyfs9e7zlft@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There were changes related to the deprecation of the "pcommit"
instruction:
fd1d961dd6 ("x86/insn: remove pcommit")
dfa169bbee ("Revert "KVM: x86: add pcommit support"")
No need to update anything in the tools, as "pcommit" wasn't being
listed on the VMX_EXIT_REASONS in the tools/perf/arch/x86/util/kvm-stat.c
file.
Just grab fresh copies of these files to silence the file cache
coherency detector:
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/home/acme/git/linux/tools/perf'
BUILD: Doing 'make -j4' parallel build
Warning: tools/arch/x86/include/asm/cpufeatures.h differs from kernel
Warning: tools/arch/x86/include/uapi/asm/vmx.h differs from kernel
INSTALL GTK UI
<SNIP>
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-07pmcc1ysydhyyxbmp1vt0l4@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 'perf probe' tool detects a variable's type and use the detected
type to add a new probe. Then, kprobes prints its variable in
hexadecimal format if the variable is unsigned and prints in decimal if
it is signed.
We sometimes want to see unsigned variable in decimal format (i.e.
sector_t or size_t). In that case, we need to investigate the variable's
size manually to specify just signedness.
This patch add signedness casting support. By specifying "s" or "u" as a
type, perf-probe will investigate variable size as usual and use the
specified signedness.
E.g. without this:
$ perf probe -a 'submit_bio bio->bi_iter.bi_sector'
Added new event:
probe:submit_bio (on submit_bio with bi_sector=bio->bi_iter.bi_sector)
You can now use it in all perf tools, such as:
perf record -e probe:submit_bio -aR sleep 1
$ cat trace_pipe|head
dbench-9692 [003] d..1 971.096633: submit_bio: (submit_bio+0x0/0x140) bi_sector=0x3a3d00
dbench-9692 [003] d..1 971.096685: submit_bio: (submit_bio+0x0/0x140) bi_sector=0x1a3d80
dbench-9692 [003] d..1 971.096687: submit_bio: (submit_bio+0x0/0x140) bi_sector=0x3a3d80
...
// need to investigate the variable size
$ perf probe -a 'submit_bio bio->bi_iter.bi_sector:s64'
Added new event:
probe:submit_bio (on submit_bio with bi_sector=bio->bi_iter.bi_sector:s64)
You can now use it in all perf tools, such as:
perf record -e probe:submit_bio -aR sleep 1
With this:
// just use "s" to cast its signedness
$ perf probe -v -a 'submit_bio bio->bi_iter.bi_sector:s'
Added new event:
probe:submit_bio (on submit_bio with bi_sector=bio->bi_iter.bi_sector:s)
You can now use it in all perf tools, such as:
perf record -e probe:submit_bio -aR sleep 1
$ cat trace_pipe|head
dbench-9689 [001] d..1 1212.391237: submit_bio: (submit_bio+0x0/0x140) bi_sector=128
dbench-9689 [001] d..1 1212.391252: submit_bio: (submit_bio+0x0/0x140) bi_sector=131072
dbench-9697 [006] d..1 1212.398611: submit_bio: (submit_bio+0x0/0x140) bi_sector=30208
This commit also update perf-probe.txt to describe "types". Most parts
are based on existing documentation: Documentation/trace/kprobetrace.txt
Committer note:
Testing using 'perf trace':
# perf probe -a 'submit_bio bio->bi_iter.bi_sector'
Added new event:
probe:submit_bio (on submit_bio with bi_sector=bio->bi_iter.bi_sector)
You can now use it in all perf tools, such as:
perf record -e probe:submit_bio -aR sleep 1
# trace --no-syscalls --ev probe:submit_bio
0.000 probe:submit_bio:(ffffffffac3aee00) bi_sector=0xc133c0)
3181.861 probe:submit_bio:(ffffffffac3aee00) bi_sector=0x6cffb8)
3181.881 probe:submit_bio:(ffffffffac3aee00) bi_sector=0x6cffc0)
3184.488 probe:submit_bio:(ffffffffac3aee00) bi_sector=0x6cffc8)
<SNIP>
4717.927 probe:submit_bio:(ffffffffac3aee00) bi_sector=0x4dc7a88)
4717.970 probe:submit_bio:(ffffffffac3aee00) bi_sector=0x4dc7880)
^C[root@jouet ~]#
Now, using this new feature:
[root@jouet ~]# perf probe -a 'submit_bio bio->bi_iter.bi_sector:s'
Added new event:
probe:submit_bio (on submit_bio with bi_sector=bio->bi_iter.bi_sector:s)
You can now use it in all perf tools, such as:
perf record -e probe:submit_bio -aR sleep 1
[root@jouet ~]# trace --no-syscalls --ev probe:submit_bio
0.000 probe:submit_bio:(ffffffffac3aee00) bi_sector=7145704)
0.017 probe:submit_bio:(ffffffffac3aee00) bi_sector=7145712)
0.019 probe:submit_bio:(ffffffffac3aee00) bi_sector=7145720)
2.567 probe:submit_bio:(ffffffffac3aee00) bi_sector=7145728)
5631.919 probe:submit_bio:(ffffffffac3aee00) bi_sector=0)
5631.941 probe:submit_bio:(ffffffffac3aee00) bi_sector=8)
5631.945 probe:submit_bio:(ffffffffac3aee00) bi_sector=16)
5631.948 probe:submit_bio:(ffffffffac3aee00) bi_sector=24)
^C#
With callchains:
# trace --no-syscalls --ev probe:submit_bio/max-stack=10/
0.000 probe:submit_bio:(ffffffffac3aee00) bi_sector=50662544)
submit_bio+0xa8200001 ([kernel.kallsyms])
submit_bh+0xa8200013 ([kernel.kallsyms])
jbd2_journal_commit_transaction+0xa8200691 ([kernel.kallsyms])
kjournald2+0xa82000ca ([kernel.kallsyms])
kthread+0xa82000d8 ([kernel.kallsyms])
ret_from_fork+0xa820001f ([kernel.kallsyms])
0.023 probe:submit_bio:(ffffffffac3aee00) bi_sector=50662552)
submit_bio+0xa8200001 ([kernel.kallsyms])
submit_bh+0xa8200013 ([kernel.kallsyms])
jbd2_journal_commit_transaction+0xa8200691 ([kernel.kallsyms])
kjournald2+0xa82000ca ([kernel.kallsyms])
kthread+0xa82000d8 ([kernel.kallsyms])
ret_from_fork+0xa820001f ([kernel.kallsyms])
0.027 probe:submit_bio:(ffffffffac3aee00) bi_sector=50662560)
submit_bio+0xa8200001 ([kernel.kallsyms])
submit_bh+0xa8200013 ([kernel.kallsyms])
jbd2_journal_commit_transaction+0xa8200691 ([kernel.kallsyms])
kjournald2+0xa82000ca ([kernel.kallsyms])
kthread+0xa82000d8 ([kernel.kallsyms])
ret_from_fork+0xa820001f ([kernel.kallsyms])
2.593 probe:submit_bio:(ffffffffac3aee00) bi_sector=50662568)
submit_bio+0xa8200001 ([kernel.kallsyms])
submit_bh+0xa8200013 ([kernel.kallsyms])
journal_submit_commit_record+0xa82001ac ([kernel.kallsyms])
jbd2_journal_commit_transaction+0xa82012e8 ([kernel.kallsyms])
kjournald2+0xa82000ca ([kernel.kallsyms])
kthread+0xa82000d8 ([kernel.kallsyms])
ret_from_fork+0xa820001f ([kernel.kallsyms])
^C#
Signed-off-by: Naohiro Aota <naohiro.aota@hgst.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hemant Kumar <hemant@linux.vnet.ibm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1470710408-23515-1-git-send-email-naohiro.aota@hgst.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The symbols used in the tick_stop tracepoint were not being converted
properly into integers in the trace_stop format file. Instead we had this:
print fmt: "success=%d dependency=%s", REC->success,
__print_symbolic(REC->dependency, { 0, "NONE" },
{ (1 << TICK_DEP_BIT_POSIX_TIMER), "POSIX_TIMER" },
{ (1 << TICK_DEP_BIT_PERF_EVENTS), "PERF_EVENTS" },
{ (1 << TICK_DEP_BIT_SCHED), "SCHED" },
{ (1 << TICK_DEP_BIT_CLOCK_UNSTABLE), "CLOCK_UNSTABLE" })
User space tools have no idea how to parse "TICK_DEP_BIT_SCHED" or the other
symbols used to do the bit shifting. The reason is that the conversion was
done with using the TICK_DEP_MASK_* symbols which are just macros that
convert to the BIT shift itself (with the exception of NONE, which was
converted properly, because it doesn't use bits, and is defined as zero).
The TICK_DEP_BIT_* needs to be denoted by TRACE_DEFINE_ENUM() in order to
have this properly converted for user space tools to parse this event.
Cc: stable@vger.kernel.org
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes: e6e6cc22e0 ("nohz: Use enum code for tick stop failure tracing message")
Reported-by: Luiz Capitulino <lcapitulino@redhat.com>
Tested-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When we don't have a tracee (i.e. we're attaching to a task or CPU),
counters can still be running after our workload finishes, and can still
be running as we read their values. As we read events one-by-one, there
can be arbitrary skew between values of events, even within a group.
This means that ratios within an event group are not reliable.
This skew can be seen if measuring a group of identical events, e.g:
# perf stat -a -C0 -e '{cycles,cycles}' sleep 1
To avoid this, we must stop groups from counting before we read the
values of any constituent events. This patch adds and makes use of a new
disable_counters() helper, which disables group leaders (and thus each
group as a whole). This mirrors the use of enable_counters() for
starting event groups in the absence of a tracee.
Closing a group leader splits the group, and without a disabled group
leader the newly split events will begin counting. Thus to ensure counts
are reliable we must defer closing group leaders until all counts have
been read. To do so this patch removes the event closing logic from the
read_counters() helper, explicitly closes the events using
perf_evlist__close(), which also aids legibility.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1470747869-3567-1-git-send-email-mark.rutland@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If module is "module" then dso->short_name is "[module]". Substring
comparing is't enough: "raid10" matches to "[raid1]". This patch also
checks terminating zero in module name.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: http://lkml.kernel.org/r/147039975648.715620.12985971832789032159.stgit@buzz
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adjust map->reloc offset for the unmapped address when finding
alternative symbol address from map, because KASLR can relocate the
kernel symbol address.
The same adjustment has been done when finding appropriate kernel symbol
address from map which was introduced by commit f90acac757 ("perf
probe: Find given address from offline dwarf")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20160806192948.e366f3fbc4b194de600f8326@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When we use libtraceevent to format trace event fields into printable
strings to use in hist entries it is important to trim it from the
default 4 KiB it starts with to what is really used, to reduce the
memory footprint, so use realloc(seq.buffer, seq.len + 1) when returning
the seq.buffer formatted with the fields contents.
Reported-and-Tested-by: Wang Nan <wangnan0@huawei.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/n/tip-t3hl7uxmilrkigzmc90rlhk2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This adds the 'bpf-output' field to the perf script usage message, and docs.
Signed-off-by: Brendan Gregg <bgregg@netflix.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1470192469-11910-4-git-send-email-bgregg@netflix.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The recent commit 599d0c954f ("mm, vmscan: move LRU lists to node"),
changed memory management code so that show_mem() is no longer safe to
call prior to setup_per_cpu_pageset(), as pgdat->per_cpu_nodestats will
still be NULL. This causes an oops on metag due to the call to
show_mem() from mem_init():
node_page_state_snapshot(...) + 0x48
pgdat_reclaimable(struct pglist_data * pgdat = 0x402517a0)
show_free_areas(unsigned int filter = 0) + 0x2cc
show_mem(unsigned int filter = 0) + 0x18
mem_init()
mm_init()
start_kernel() + 0x204
This wasn't a problem before with zone_reclaimable() as zone_pcp_init()
was already setting zone->pageset to &boot_pageset, via setup_arch() and
paging_init(), which happens before mm_init():
zone_pcp_init(...)
free_area_init_core(...) + 0x138
free_area_init_node(int nid = 0, ...) + 0x1a0
free_area_init_nodes(...) + 0x440
paging_init(unsigned long mem_end = 0x4fe00000) + 0x378
setup_arch(char ** cmdline_p = 0x4024e038) + 0x2b8
start_kernel() + 0x54
No other arches appear to call show_mem() during boot, and it doesn't
really add much value to the log, so lets just drop it from mem_init().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-metag@vger.kernel.org
There only ever have been two host implementations of the old
s390-virtio (pre-ccw) transport: the experimental kuli userspace,
and qemu. As qemu switched its default to ccw with 2.4 (with most
users having used ccw well before that) and removed the old transport
entirely in 2.6, s390-virtio probably hasn't been in active use for
quite some time and is therefore likely to bitrot.
Let's start the slow march towards removing the code by deprecating
it.
Note that this also deprecates the early virtio console code, which
has been causing trouble in the guest without being wired up in any
relevant hypervisor code.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In case the registration of the hvc tty never happens AND the kernel
thinks that hvc0 is the preferred console we should keep the early
printk function to avoid a kernel panic due to code being removed.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We do a lot of memory allocation in function init_vq, and don't handle
the allocation failure properly. Then this function will return 0,
although initialization fails due to lacking memory. At that moment,
kernel will panic in guest machine, if virtio is used to drive disk.
To fix this bug, we should take care of allocation failure, and return
correct value to let caller know what happen.
Tested-by: Chao Fan <fanc.fnst@cn.fujitsu.com>
Signed-off-by: Minfei Huang <mnghuan@gmail.com>
Signed-off-by: Minfei Huang <minfei.hmf@alibaba-inc.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Stash the packet length in a local variable before handing over
ownership of the packet to virtio_transport_recv_pkt() or
virtio_transport_free_pkt().
This patch solves the use-after-free since pkt is no longer guaranteed
to be alive.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On error, virtqueue_add calls START_USE but not
END_USE. Thankfully that's normally empty anyway,
but might not be when debugging. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When using the indirect buffers feature, 'desc' is allocated in
virtqueue_add() but isn't freed before leaving on a ring full error,
causing a memory leak.
For example, it seems rather clear that this can trigger
with virtio net if mergeable buffers are not used.
Cc: stable@vger.kernel.org
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable the hard limit of cpu count by set boot options nr_cpus=x
on arm64, and make a minor change about message when total number
of cpu exceeds the limit.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reported-by: Shiyuan Hu <hushiyuan@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The generic allocation code may sometimes decide to assign a prefetchable
64-bit BAR to the M32 window. In fact it may also decide to allocate
a 64-bit non-prefetchable BAR to the M64 one ! So using the resource
flags as a test to decide which window was used for PE allocation is
just wrong and leads to insane PE numbers.
Instead, compare the addresses to figure it out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename the function as agreed by Ben & Gavin]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When machine check occurs with MSR(RI=0), it means MC interrupt is
unrecoverable and kernel goes down to panic path. But the console
message still shows it as recovered. This patch fixes the MCE console
messages.
Fixes: 36df96f8ac ("powerpc/book3s: Decode and save machine check event.")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The tick_nohz_stop_sched_tick() routine is not properly
canceling the sched timer when nothing is pending, because
get_next_timer_interrupt() is no longer returning KTIME_MAX in
that case. This causes periodic interrupts when none are needed.
When determining the next interrupt time, we first use
__next_timer_interrupt() to get the first expiring timer in the
timer wheel. If no timer is found, we return the base clock value
plus NEXT_TIMER_MAX_DELTA to indicate there is no timer in the
timer wheel.
Back in get_next_timer_interrupt(), we set the "expires" value
by converting the timer wheel expiry (in ticks) to a nsec value.
But we don't want to do this if the timer wheel expiry value
indicates no timer; we want to return KTIME_MAX.
Prior to commit 500462a9de ("timers: Switch to a non-cascading
wheel") we checked base->active_timers to see if any timers
were active, and if not, we didn't touch the expiry value and so
properly returned KTIME_MAX. Now we don't have active_timers.
To fix this, we now just check the timer wheel expiry value to
see if it is "now + NEXT_TIMER_MAX_DELTA", and if it is, we don't
try to compute a new value based on it, but instead simply let the
KTIME_MAX value in expires remain.
Fixes: 500462a9de "timers: Switch to a non-cascading wheel"
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1470688147-22287-1-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
