For non-monitor interfaces, the syntax for alloc_ieee80211/free_80211
is wrong. Because alloc_ieee80211 only creates (wiphy_new) a wiphy, but
free_80211() does wiphy_unregister() also. This is only correct when
the later wiphy_register() is called successfully, which apparently
is not the case for your fw doesn't exist one.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before bringing up a sky2 interface up ethtool reports
"Link detected: yes". Do as ixgbe does and netif_carrier_off() on
probe().
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of PreMax ethernet pcmcia card,
and some Sierra Wireless serial card(AC555, AC7xx, AC8xx).
use PROD_ID for AC7xx, because MANF_ID of AC7xx and AC8xx are the same.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8169 card drop incoming VLAN tagged MTU byte large jumbo frames
It looks to compare current and maximal packet sizes hardware use
'<' operator, not '<='.
Bug introduced by commit fdd7b4c330
("r8169: fix crash when large packets are received")
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead. This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change in how PHYs are electrically isolated caused all PHYs to be
isolated followed by reverting that isolation for the selected PHY.
Unfortunately, isolating the selected PHY for even a short period of
time can result in DHCP negotiation taking more than 10 seconds on certain
embedded configurations delaying boot time as reported by Bernhard Kaindl.
This patch reverts the change to how PHYs are isolated yet still works
around the issue for 82552 needing the selected PHY's BMCR register to
be written after the unused PHYs are isolated. This code is moved below
the setting of nic->phy ID in order to do the 82552-specific workaround.
Cc: Bernhard Kaindl <bernhard.kaindl@gmx.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
net: Fix 'Re: PACKET_TX_RING: packet size is too long'
netdev: usb: dm9601.c can drive a device not supported yet, add support for it
qlge: Fix firmware mailbox command timeout.
qlge: Fix EEH handling.
AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl (v2)
bonding: fix a race condition in calls to slave MII ioctls
virtio-net: fix data corruption with OOM
sfc: Set ip_summed correctly for page buffers passed to GRO
cnic: Fix L2CTX_STATUSB_NUM offset in context memory.
MAINTAINERS: rt2x00 list is moderated
airo: Reorder tests, check bounds before element
mac80211: fix for incorrect sequence number on hostapd injected frames
libertas spi: fix sparse errors
mac80211: trivial: fix spelling in mesh_hwmp
cfg80211: sme: deauthenticate on assoc failure
mac80211: keep auth state when assoc fails
mac80211: fix ibss joining
b43: add 'struct b43_wl' missing declaration
b43: Fix Bugzilla #14181 and the bug from the previous 'fix'
rt2x00: Fix crypto in TX frame for rt2800usb
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: order used ring after used index read
virtio-pci: fix per-vq MSI-X request logic
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] zfcp: Flush SCSI registration work when adding unit
[SCSI] zfcp: Fix timer initialization for ct and els requests
[SCSI] zfcp: Warn about storage devices with broken PLOGI data
[SCSI] zfcp: Handle WWPN mismatch in PLOGI payload
[SCSI] zfcp: fix kfree handling in zfcp_init_device_setup
[SCSI] fix memory leak in initialization
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: fix kms/fbdev colormap support properly.
drm: Add the basic check for the detailed timing in EDID
drm/radeon/kms: ignore vga arbiter return.
I've not touched the other stuff here but the word "locking" comes to mind.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/ppc64: Use preempt_schedule_irq instead of preempt_schedule
powerpc: Minor cleanup to lib/Kconfig.debug
powerpc: Minor cleanup to sound/ppc/Kconfig
powerpc: Minor cleanup to init/Kconfig
powerpc: Limit memory hotplug support to PPC64 Book-3S machines
powerpc: Limit hugetlbfs support to PPC64 Book-3S machines
powerpc: Fix compile errors found by new ppc64e_defconfig
powerpc: Add a Book-3E 64-bit defconfig
powerpc/booke: Fix xmon single step on PowerPC Book-E
powerpc: Align vDSO base address
powerpc: Fix segment mapping in vdso32
powerpc/iseries: Remove compiler version dependent hack
powerpc/perf_events: Fix priority of MSR HV vs PR bits
powerpc/5200: Update defconfigs
drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEM
powerpc/boot/dts: drop obsolete 'fsl5200-clocking'
of: Remove nested function
mpc5200: support for the MAN mpc5200 based board mucmc52
mpc5200: support for the MAN mpc5200 based board uc101
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Do not dereference null pointer in twl4030 error path
mfd: Always initialise WM831x IRQ mutex
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Fix VID reading on IT8718F/IT8720F
hwmon: (dme1737) No vid attributes for SCH311x
hwmon: (fschmd) Fix check on unsigned in watchdog_write()
hwmon: (coretemp) Maintainer update
* 'urgent-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: do not load the pd6729 driver if io_base is NULL
pcmcia: Fix possible printk format warnings
pcmcia: do not try to store more than 4 version strings
pcmcia: pccard_read_tuple and TUPLE_RETURN_COMMON cleanup
pcmcia: properly close previous dev_printk if kzalloc fails in do_io_probe
pcmcia: fix controller printk format warnings
I have an HP HDX 18 laptop, and noted that the configuration of the
accelerometer needs to be x_inverted.
Signed-off-by: Ian E. Morgan <penguin.wrangler@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have learned that the 6730b and 6730s have different accelerometer
orientation, and have modified the driver accordingly (diff attached),
while dropping the wild guess for AMD based 6735 having the same
orientation as Intel based 6730 (this is not true for any other related
series/family, thus is not probable for 673x).
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the case where cpuidle_idle_call() returns before changing state due to
a need_resched(), it was returning with IRQs disabled.
The idle path assumes that the platform specific idle code returns with
interrupts enabled (although this too is undocumented AFAICT) and on ARM
we have a WARN_ON(!(irqs_disabled()) when returning from the idle loop, so
the user-visible effects were only a warning since interrupts were
eventually re-enabled later.
On x86, this same problem exists, but there is no WARN_ON() to detect it.
As on ARM, the interrupts are eventually re-enabled, so I'm not sure of
any actual bugs triggered by this. It's primarily a
correctness/consistency fix.
This patch ensures IRQs are (re)enabled before returning.
Reported-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Cc: <stable@kernel.org> [2.6.31.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow csrows to properly initialize when the topology only has active
channels on 2 and 3. This new check allows proper detection and
initialization in this topology. Only checking the first mrt that
represented channels 0 and 1 is not sufficient.
I also fixed up the related debug information path. I can submit as a 2nd
patch if needed.
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Acked-by: Aristeu Rozanski <aris@ruivo.org>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building without CONFIG_PCI the edac_pci_idx variable is unused,
causing a build-time warning. Wrap the variable in #ifdef CONFIG_PCI,
just like the rest of the PCI support.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5400 EDAC driver has several bugs with chip-select row computation
which most likely lead to bugs in detailed error reporting. Attempts to
contact the authors have gone mostly unanswered so I am presenting my diff
here. I do not subscribe to lkml and would appreciate being kept in the
cc.
The most egregious problem was miscalculating the addresses of MTR
registers after register 0 by assuming they are 32bit rather than 16.
This caused the driver to miss half of the memories. Most motherboards
tend to have only 8 dimm slots and not 16, so this may not have been
noticed before.
Further, the row calculations multiplied the number of dimms several
times, ultimately ending up with a maximum row of 32. The chipset only
supports 4 dimms in each of 4 channels, so csrow could not be higher than
4 unless you use a row per-rank with dual-rank dimms. I opted to
eliminate this behavior as it is confusing to the user and the error
reporting works by slot and not rank. This gives a much clearer view of
memory by slot and channel in /sys.
Signed-off-by: Jeff Roberson <jroberson@jroberson.net>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpio_twl4030_probe() function calls gpio_twl4030_remove(), and the
former has __devinit, so the latter cannot use __devexit. Otherwise we
hit the section mismatch warning:
WARNING: drivers/gpio/built-in.o(.devinit.text+0x71a): Section mismatch
in reference from the function _gpio_twl4030_probe() to the function
.devexit.text:_gpio_twl4030_remove()
The function __devinit _gpio_twl4030_probe() references a function
__devexit _gpio_twl4030_remove().
This is often seen when error handling in the init function uses
functionality in the exit path.
The fix is often to remove the __devexit annotation of
_gpio_twl4030_remove() so it may be used outside an exit section.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IBM Saturn serial card has only one port. Without that fixup,
the kernel thinks it has two, which confuses userland setup and
admin tools as well.
[akpm@linux-foundation.org: fix pci-ids.h layout]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Michael Reed <mreed10@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
is_power_of_2() appears not to be constant enough for BUILD_BUG_ON()
after the latest rework, so replace it with an open-coded test.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The missing probe handler hook will never probe the driver. Add it back.
Fixes broken MMC on OMAP.
We use platform_driver_probe() API since omap_hsmmc is not a hot-pluggable
device.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After copying uts->nodename to the static nodename array the static
version isn't necessarily zero termininated, since the size of the
array is one byte too short.
Afterwards doing strncat(data, nodename, strlen(nodename)); may copy
an arbitrary large amount of bytes.
Fix this by getting rid of the static array and using strncat with
proper length limit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix missing unregister_sysctl_table in case the SCLP doesn't provide
the requested feature. Also simplify the whole error handling while
at it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a suspended z/VM guest has been logged off before the resume the
'SET SMSG IUCV' CP command need to be repeated to reenable sending
message via SMSG. This fixes the following error:
HCPMFS057I H4214002 not receiving; SMSG off
Error: non-zero CP response for command 'SMSG H4214002 CMM SHRINK 5010': #57
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the size of the local buffer and use snprintf to prevent
further miscalculations. Also fix the usage of bitwise vs logic
operations.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.
Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2
- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
are corrupted, there are twiddled single bits 1->0 and some full 32-bit
words corrupted, sometimes commands fail (which switches /dev/hda to
PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.
This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up driver resources without touch the hardware. Add pci
save/restore state.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mii monitor mode, bond_check_dev_link() calls the the ioctl
handler of slave devices. It stores the ndo_do_ioctl function
pointer to a static (!) ioctl variable and later uses it to call the
handler with the IOCTL macro.
If another thread executes bond_check_dev_link() at the same time
(even with a different bond, which none of the locks prevent), a
race condition occurs. If the two racing slaves have different
drivers, this may result in one driver's ioctl handler being
called with a pointer to a net_device controlled with a different
driver, resulting in unpredictable breakage.
Unless I am overlooking something, the "static" must be a
copy'n'paste error (?).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SMP guests, reads from the ring might bypass used index reads. This
causes guest crashes because host writes to used index to signal ring
data readiness. Fix this by inserting rmb before used ring reads.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Commit f68d24082e
in 2.6.32-rc1 broke requesting IRQs for per-VQ MSI-X vectors:
- vector number was used instead of the vector itself
- we try to request an IRQ for VQ which does not
have a callback handler
This is a regression that causes warnings in kernel log,
potentially lower performance as we need to scan vq list,
and might cause system failure if the interrupt
requested is in fact needed by another system.
This was not noticed earlier because in most cases
we were falling back on shared interrupt for all vqs.
The warnings often look like this:
virtio-pci 0000:00:03.0: irq 26 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 27 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 28 for MSI/MSI-X
IRQ handler type mismatch for IRQ 1
current handler: i8042
Pid: 2400, comm: modprobe Tainted: G W
2.6.32-rc3-11952-gf3ed8d8-dirty #1
Call Trace:
[<ffffffff81072aed>] ? __setup_irq+0x299/0x304
[<ffffffff81072ff3>] ? request_threaded_irq+0x144/0x1c1
[<ffffffff813455af>] ? vring_interrupt+0x0/0x30
[<ffffffff81346598>] ? vp_try_to_find_vqs+0x583/0x5c7
[<ffffffffa0015188>] ? skb_recv_done+0x0/0x34 [virtio_net]
[<ffffffff81346609>] ? vp_find_vqs+0x2d/0x83
[<ffffffff81345d00>] ? vp_get+0x3c/0x4e
[<ffffffffa0016373>] ? virtnet_probe+0x2f1/0x428 [virtio_net]
[<ffffffffa0015188>] ? skb_recv_done+0x0/0x34 [virtio_net]
[<ffffffffa00150d8>] ? skb_xmit_done+0x0/0x39 [virtio_net]
[<ffffffff8110ab92>] ? sysfs_do_create_link+0xcb/0x116
[<ffffffff81345cc2>] ? vp_get_status+0x14/0x16
[<ffffffff81345464>] ? virtio_dev_probe+0xa9/0xc8
[<ffffffff8122b11c>] ? driver_probe_device+0x8d/0x128
[<ffffffff8122b206>] ? __driver_attach+0x4f/0x6f
[<ffffffff8122b1b7>] ? __driver_attach+0x0/0x6f
[<ffffffff8122a9f9>] ? bus_for_each_dev+0x43/0x74
[<ffffffff8122a374>] ? bus_add_driver+0xea/0x22d
[<ffffffff8122b4a3>] ? driver_register+0xa7/0x111
[<ffffffffa001a000>] ? init+0x0/0xc [virtio_net]
[<ffffffff81009051>] ? do_one_initcall+0x50/0x148
[<ffffffff8106e117>] ? sys_init_module+0xc5/0x21a
[<ffffffff8100af02>] ? system_call_fastpath+0x16/0x1b
virtio-pci 0000:00:03.0: irq 26 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 27 for MSI/MSI-X
Reported-by: Marcelo Tosatti <mtosatti@redhat.com>
Reported-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio net used to unlink skbs from send queues on error,
but ever since 48925e372f
we do not do this. This causes guest data corruption and crashes
with vhost since net core can requeue the skb or free it without
it being taken off the list.
This patch fixes this by queueing the skb after successful
transmit.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO. The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:
commit 078b073588
bnx2: Update firmware to 5.0.0.j3.
Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we will get the incorrect display modeline when parsing the detailed
timing in EDID. For example:
>hsync/vsync width is zero
>sync is beyond the blank.
So add the basic check for the detailed timing in EDID to avoid the incorrect
display modeline.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since we register all radeon devices, and the arbiter only cares about
VGA class ones, we will fail to startup on display controller class devices.
We don't gain anything by using the return value here.
this helps kms on sparc64 get started.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Test whether index is within bounds before reading the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'struct b43_wl' declaration is missing at 'leds.h'.
It should be declared to avoid getting some GCC warnings at 'b43_leds_unregister'.
Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"b43: Fix PPC crash in rfkill polling on unload" fixed the bug reported
in Bugzilla No. 14181; however, it introduced a new bug. Whenever the
radio switch was turned off, it was necessary to unload and reload
the driver for it to recognize the switch again.
This patch fixes both the original bug in #14181 and the bug introduced by
the previous patch. It must be stated, however, that if there is a BCM4306/3
with an rfkill switch (not yet proven), then the driver will need an
unload/reload cycle to turn the device back on.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 308cf8e13f. This
patch had trouble with transparent bridges, among other things. A more
readable and correct version should land in 2.6.33.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add include asm/cacheflush.h, because declaration of __flush_purge_region
moved to asm/cacheflush.h.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more careful about the state of pointers during tear-down.
The "pppoe_dev" field can only be looked at safely while holding socket locks.
This subsequently allows for the flush_lock to be killed.
We depend on the PPPOX_CONNECTED state to tell us that that those fields are
valid, so whoever clears that state (pppox_unbind_sock()) is responsible for
the dev_put() call.
We also have to ensure that we delete_item() on all sockets before they are
cleaned up.
The need for these changes has been exposed by scenarios wherein namespace
bindings of ethernet devices change while there are ongoing PPPoE sessions,
which resulted in oopses due to unusual socket connection termination paths,
exposing these issues.
Signed-off-by: Michal Ostrowski <mostrows@gmail.com>
Reviewed-by: Cyril Gorcunov <gorcunov@gmail.com>
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Tested-by: Denys Fedoryschenko <denys@visp.net.lb>
We are mistakenly dereferencing twl->client in the twl->client null checking
path.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This avoids crashes when running without interrupt support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to
hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses
in order to perform sw-driven PHY configuration during initialization to
workaround known hardware issues (see follow-on patch). This patch
provides new PHY read/write functions (and function pointers) that will
allow accessing the PHY registers assuming the swflag has already been
acquired. The actual PHY register access code has moved into helper
functions that are called with a flag indicating whether or not the swflag
has already been acquired and acquires/releases it if not.
The functions called from within the updated PHY access functions had to be
updated to assume the swflag was already acquired, and other functions that
called those functions were also updated to acquire/release the swflag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accesses to NVM and PHY/CSR registers on ICHx/PCH-based parts are protected
from concurrent accesses with a mutex that is acquired when the access is
initiated and released when the access has completed. However, the two
types of accesses should not be protected by the same mutex because the
driver may have to access the NVM while already holding the mutex over
several consecutive PHY/CSR accesses which would result in livelock.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike previous ICHx-based parts, the PCH-based parts (82577/82578) require
LPLU (Low Power Link Up, or "reverse auto-negotiation") to be configured in
the PHY rather than the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some conditions (e.g. when AMT is enabled on the system), it is possible
to take an extended period of time to for the driver to acquire the sw/fw/hw
hardware semaphore used to protect against concurrent access of a shared
resource (e.g. PHY registers). This could cause PHY registers to not get
configured properly resulting in link issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing a dummy read of the PHY Wakeup Control (WUC) register clears the
wakeup enable bit set by an PHY reset. If this bit remains set, link
problems may occur.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing ring sizes while the interface was down was causing a double
allocation of the receive and transmit rings. This issue is amplified when
there are multiple rings enabled. To prevent this we need to add an
additional check which will just update the ring counts when the interface
is not up and skip the allocation steps.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CL-PD6729 chip in some docking station is not initialized properly
under Linux. In that case, do not load the pd6729 driver.
[Dominik Brodowski <linux@dominikbrodowski.net>: spelling fixes, check for NULL not 0]
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.
The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000B revision ID is 0x1A, not 0x1B as set in the curernt
dm9000.h header.
Fix bug reported by Paolo Zebelloni.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8110SC rev d chip on our board shows a regression which the 8110SB chip
did not have. When inbound traffic is overflowing the receive descriptor queue,
"holes" in the ring buffer may occur which lead to a hangup until the buffer
is filled again. The packets are than completely processed, but the ring
remains porous and no packets are processed until the next overflow. Setting
the interface down and up can fix the problem temporary from userspace.
For some reason we don't know, this behaviour is not occuring if the RxVlan
bit for hardware VLAN untagging is set. There is another "Work around for
AMD plateform" in the current code which checks the VLAN status
word in receive descriptors, but does never come to effect when hardware
VLAN support is enabled. We assume that this is a bug in the chip.
The following patch fixes the problem. Without the patch we could reproduce
the hang within minutes (given other devices also generating lots of
interrupts), without we couldn't reproduce within a few days of long term
testing.
This version contains minor style adjustments and is sent with mutt which
will hopefully not destroy the formatting again.
Signed-off-by: Bernhard Schmidt <bernhard.schmidt@saxnet.de>
Signed-off-by: Simon Wunderlich <simon.wunderlich@saxnet.de>
Acked-by: Francois Romieu <romieu@zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing apples to bananas doesn't seem right. Consistently use the
chips enum for chip type comparisons, to avoid such bugs in the
future.
The bug has been there since support for the IT8718F was added, so
VID never worked for this chip nor for the similar IT8720F.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SCH311x chips do not have VID inputs, so the cpu0_vid and vrm
attributes shouldn't be created for them.
This fixes lm-sensors ticket #2353:
http://www.lm-sensors.org/ticket/2353
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Udo van den Heuvel <udovdh@xs4all.nl>
Cc: Juerg Haefliger <juergh@gmail.com>
If unsigned the watchdog_trigger() return value will not be
checked correctly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
At this point (ri_tasklet()), RTNL or dev_base_lock are not held,
we must use dev_get_by_index() instead of __dev_get_by_index()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes the following build failure:
CC drivers/net/au1000_eth.o
/drivers/net/au1000_eth.c: In function 'au1000_set_settings':
/drivers/net/au1000_eth.c:623: error: implicit declaration of function 'capable'
/drivers/net/au1000_eth.c:623: error: 'CAP_NET_ADMIN' undeclared (first use in this function)
/drivers/net/au1000_eth.c:623: error: (Each undeclared identifier is reported only once
/drivers/net/au1000_eth.c:623: error: for each function it appears in.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the reporting of myri10ge port type in ethtool,
and update for new boards.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx
state in order for the PHY write which disables gigabit speed to take
effect. Gigabit speed must be disabled in order for the PHY writes to
registers on page 800 (the wakeup control registers) to work as expected
otherwise the system might not wake via WoL.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a circular locking dependency:
---> isdn_net_get_locked_lp
--->lock &nd->queue_lock
--->lock &nd->queue->xmit_lock
.....................
---->unlock &nd->queue_lock
---> isdn_net_writebuf_skb (called with &nd->queue->xmit_lock locked)
---->isdn_net_inc_frame_cnt
---->isdn_net_device_busy
----> lock &nd->queue_lock
This will trigger lockdep warnings:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.32-rc4-testing #7
-------------------------------------------------------
ipppd/28379 is trying to acquire lock:
(&netdev->queue_lock){......}, at: [<e62ad0fd>] isdn_net_device_busy+0x2c/0x74 [isdn]
but task is already holding lock:
(&netdev->local->xmit_lock){+.....}, at: [<e62aefc2>] isdn_net_write_super+0x3f/0x6e [isdn]
which lock already depends on the new lock.
.......
We don't need to lock nd->queue->xmit_lock to protect single
isdn_net_lp_busy(). This can fix above lockdep warnings.
Reported-and-tested-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code assumed board config version in the flash to be 1.
When this will get changed by tools, driver just refuses to
attach. This is unnecessary since driver does not have to
parse board config structure directly (maintained by firmware).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
move virtrng_remove to .devexit.text
move virtballoon_remove to .devexit.text
virtio_blk: Revert serial number support
virtio: let header files include virtio_ids.h
virtio_blk: revert QUEUE_FLAG_VIRT addition
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
niu: VLAN_ETH_HLEN should be used to make sure that the whole MAC header was copied to the head buffer in the Vlan packets case
KS8851: Fix ks8851_set_rx_mode() for IFF_MULTICAST
KS8851: Fix MAC address write order
KS8851: Add soft reset at probe time
net: fix section mismatch in fec.c
net: Fix struct inet_timewait_sock bitfield annotation
tcp: Try to catch MSG_PEEK bug
net: Fix IP_MULTICAST_IF
bluetooth: static lock key fix
bluetooth: scheduling while atomic bug fix
tcp: fix TCP_DEFER_ACCEPT retrans calculation
tcp: reduce SYN-ACK retrans for TCP_DEFER_ACCEPT
tcp: accept socket after TCP_DEFER_ACCEPT period
Revert "tcp: fix tcp_defer_accept to consider the timeout"
AF_UNIX: Fix deadlock on connecting to shutdown socket
ethoc: clear only pending irqs
ethoc: inline regs access
vmxnet3: use dev_dbg, fix build for CONFIG_BLOCK=n
virtio_net: use dev_kfree_skb_any() in free_old_xmit_skbs()
be2net: fix support for PCI hot plug
...
OQO 01+ multimedia keys produce 6x on press, e0 6x upon release.
As a result, Linux thinks that another key has been pressed (or is
repeating), when it is actually a release of the same key. Mangle the
release scancode when running on OQO so that driver recognizes it as
such.
Since the device does not have external PS/2 ports mangling is safe
since there is no chance that an external keyboard is connected.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The function virtrng_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The function virtballoon_remove is used only wrapped by __devexit_p so
define it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This reverts "Add serial number support for virtio_blk, V4a".
Turns out that virtio_pci, lguest and s/390 all have an 8 bit limit
on virtio config space, so noone could ever use this.
This is coming back later in a cleaner form.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: john cooper <john.cooper@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Rusty,
commit 3ca4f5ca73
virtio: add virtio IDs file
moved all device IDs into a single file. While the change itself is
a very good one, it can break userspace applications. For example
if a userspace tool wanted to get the ID of virtio_net it used to
include virtio_net.h. This does no longer work, since virtio_net.h
does not include virtio_ids.h.
This patch moves all "#include <linux/virtio_ids.h>" from the C
files into the header files, making the header files compatible with
the old ones.
In addition, this patch exports virtio_ids.h to userspace.
CC: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It seems like the addition of QUEUE_FLAG_VIRT caueses major performance
regressions for Fedora users:
https://bugzilla.redhat.com/show_bug.cgi?id=509383https://bugzilla.redhat.com/show_bug.cgi?id=505695
while I can't reproduce those extreme regressions myself I think the flag
is wrong.
Rationale:
QUEUE_FLAG_VIRT expands to QUEUE_FLAG_NONROT which casus the queue
unplugged immediately. This is not a good behaviour for at least
qemu and kvm where we do have significant overhead for every
I/O operations. Even with all the latested speeups (native AIO,
MSI support, zero copy) we can only get native speed for up to 128kb
I/O requests we already are down to 66% of native performance for 4kb
requests even on my laptop running the Intel X25-M SSD for which the
QUEUE_FLAG_NONROT was designed.
If we ever get virtio-blk overhead low enough that this flag makes
sense it should only be set based on a feature flag set by the host.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When configuring a LUN for use in zfcp, flush the SCSI work to ensure
the SCSI device has been created before returning. This means that a
configuration procedure can run these commands in a script and the
SCSI device is available immediately after the unit_add:
echo 1 > /sys/bus/ccw/drivers/zfcp/0.0.181d/online
echo 0x401040C300000000 > \
/sys/bus/ccw/drivers/zfcp/0.0.181d/0x500507630313c562/unit_add
lsscsi
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add HZ since the start_timer function expects jiffies, not seconds.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After opening a remote port zfcp checks if the WWPN returned in the
PLOGI maches the WWPN of the port that should have been opened. On a
mismatch zfcp assumes that the DID just changed, queries the FC
nameserver and tries again. If the situation persists the erp will
give up.
With this strategy, if the remote port always returns the wrong PLOGI
data, the remote port will not be opened. Introduce a warning, so that
the system administrator knows why the remote port is not being opened
and to have a pointer to investigate the problem on the storage
system.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For ports, zfcp gets the DID from the FC nameserver and tries to open
the port. If the open succeeds, zfcp compares the WWPN from the
nameserver with the WWPN in the PLOGI payload. In case of a mismatch,
zfcp assumes that the DID of the port just changed and we opened the
wrong port. This means that zfcp has to forget the DID, lookup the DID
again and retry.
This error case had a problem that zfcp forgets the DID, but never
looks up a new one, stalling the ERP in this case. Fix this by
triggering the DID lookup and properly exit from the ERP. The DID
lookup will trigger a new ERP action.
Also ensure when trying to open the port again with the new DID, first
close the open port, even in the NOESC case.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
