The picodlp panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_generic_dpi_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The picodlp panel driver leaves gpio requests to the platform's board file.
These should happen in the panel driver itself.
A platform data struct called picodlp_panel_data already exists to hold gpio
numbers and other platform data. Request all the gpios in the panel driver so
that the board files which use the the panel don't need to do it.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The tpo-td043 panel driver now manages the gpios required to configure the panel.
This was previously done in omap_dss_device's platform_enable/disable callbacks
defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_tpo_td043_data struct, which is needed by the panel driver to
configure the gpios connected to the panel. Hence, the platform_enable/disable
ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The tpo-td043mtea1 panel driver leaves gpio configurations to the
platform_enable and disable calls in the platform's board file. These should
happen in the panel driver itself.
Create a platform data struct for the panel, this contains the reset gpio
number used by the panel driver, this struct will be passed to the panel driver
as platform data. The driver will request and configure the reset gpio rather
than leaving it to platform callbacks in board files.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The nec-nl8048 panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_nec_nl8048_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The nec-nl8048hl11-01 panel driver leaves gpio configurations to the
platform_enable and disable calls in the platform's board file. These should
happen in the panel driver itself.
Create a platform data struct for the panel, this contains the gpio numbers
used by the panel driver, this struct will be passed to the panel driver as
platform data. The driver will request and configure these gpios rather than
leaving it to platform callbacks in board files.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The acx565akm panel driver leaves gpio configurations to the platform_enable
and disable calls in the platform's board file. These should happen in the panel
driver itself.
Create a platform data struct for the panel, this contains the reset gpio number
used by the panel driver, this struct will be passed to the panel driver as
platform data. The driver will request and configure the reset gpio rather than
leaving it to platform callbacks in board files.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The sharp-ls panel driver now manages the gpios required to configure the panel.
This was previously done in omap_dss_device's platform_enable/disable callbacks
defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_sharp_ls037v7dw01_data struct, which is needed by the panel
driver to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
Move the GPIO handling from board file's platform callbacks to the panel
driver, which gets the gpios via platform data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The generic dpi panel driver now sets the gpios required to configure the panel.
This was previously done in platform_enable/disable callbacks in board files.
All the board files using generic dpi panel now correctly pass the gpio related
information as platform data, which is needed by the panel driver to configure
the panel. Hence, the platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The lgphilips panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.
All the board files using this panel now pass the gpio information as platform
data via the panel_generic_dpi_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>
The lgphilips panel driver leaves gpio configurations to the platform_enable
and disable calls in the platform's board file. These should happen in the
panel driver itself.
Use the platform data as defined for generic dpi panels to pass gpio information
to the lgphilips driver.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>
The generic dpi panel driver leaves gpio configurations to the platform_enable
and disable calls in the platform's board file. These should happen in the
panel driver itself.
Add a generic way of passing gpio information to the generic dpi panel driver
via it's platform_data. This information includes the number of gpios used by
the panel, the gpio number and logic level (active high/low) for each gpio. This
gpio data will be used by the driver to request and configure the gpios required
by the panel.
This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
The omap_dss_device structs's max_backlight_level is used to pass maximum
backlight level for the platform. However, no board file using this panel
populates this field. Therefore, we remove it's usage from the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Use devm_kzalloc instead of kzalloc to allocate driver data for the picodlp
panel driver. This simplifies the driver's probe and remove functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Use devm_kzalloc instead of kzalloc to allocate driver data for the lg phillips
panel driver. This simplifies the driver's probe and remove functions.
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Use devm_kzalloc instead of kzalloc to allocate driver data for the generic dpi
panel driver. This simplifies the driver's probe and remove functions.
Signed-off-by: Archit Taneja <archit@ti.com>
The n8x0 panel contains support to call platform backlight functions.
These are not used by any board, and can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
NEC-nl8048hl11 driver contains support to call platform backlight
functions. These are not used by any board, and can be removed.
Signed-off-by: Archit Taneja <archit@ti.com>
Sharp ls037v7dw01 driver contains support to call platform backlight
functions. These are not used by any board, and can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
acx565akm has support to call set_backlight/get_backlight in platform
code. They are not used by any board, and thus can be removed from the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Structs for platform data of omapdss panels are found in headers in the
'include/video/' path. Board files populate these structs with platform
specific values, and the panel driver uses these to configure the panel.
Currently, each panel has it's own header in the above path. Move all the
omapdss panel platform data structs to a single header omap-panel-data.h.
This is useful because:
- All other omapdss panel drivers will be modified to use platform data. This
would lead to a lot of panel headers usable only by omapdss. A lot of these
platform data structs are trivial, and don't really need a separate header.
- Platform data would be eventually removed, and platform information would be
passed via device tree. Therefore, omapdss panel platform data structs are
temporary, and will be easier to remove if they are all in the same header.
- All board files will have to include the same header to configure a panel's
platform data, that makes the board files more consistent.
Signed-off-by: Archit Taneja <archit@ti.com>
* OMAP display fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CIGs
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-3.9-rc4' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev fixes from Tomi Valkeinen:
"Since Florian is still away/inactive, I volunteered to collect fbdev
fixes for 3.9 and changes for 3.10. I didn't receive any other fbdev
fixes than OMAP yet, but I didn't want to delay this further as
there's a compilation fix for OMAP1. So there could be still some
fbdev fixes on the way a bit later.
This contains:
- Fix OMAP1 compilation
- OMAP display fixes"
* tag 'fbdev-fixes-3.9-rc4' of git://gitorious.org/linux-omap-dss2/linux:
omapdss: features: fix supported outputs for OMAP4
OMAPDSS: tpo-td043 panel: fix data passing between SPI/DSS parts
omapfb: fix broken build on OMAP1
Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email address.
He submitted the patch earlier, but nobody felt responsible to pick
it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that
leads to unbootable kernels on all other machines and that needs
to depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUVBQf2CrR//JCVInAQJwyRAA0qzt+jbn+ezvLpeWvrgdEVLikiAieVyt
HmSex/pEWh2ytIkrX2maHv5Oov9QmX7v4ZEU2WtdvMv5YERsT7/y1hjHaZTLcdmH
11ogfVwTRbrNVWOb41ofdd3rUVgZfgzCGQ0rfEua3wLRK6AetZJxkqsuGXRaqjdm
BBbmgKAmLsLeM3/aBzeuFint1+EDY74WBMxgqkwUretefKFMxzcBaqhoR+FNDIdV
YaYbOocq45LsOa44gxlF6pmJkZsOsB2pqAjoANm5KtZlphTEpDD1C/wXvBaVAOBh
8mCuk2mHEyZsyLrufh/ZywaPcDaUMDwpO1zidATwaRCf6qWOr3jtWiCtQo4FeNYS
o+kkYtELyAEvwDQuljghviq0p+z2vpnk52sYdXkYW8Pgz5TqhK+Gu2ywaeiqeT2B
cbLGG32lVgJnmWOOXI7Z6MjekgKx5arx7z6Br+1pTT/fE44DgE+CtabEsCdcpFWG
ftC7FdxZabDUhfynSaO43tgKhdVv2XpVobG3iW2RYJOWm2dJSxulZg9+jypdxITm
VX3kPar+mjvwyf3svsGIc65SVaayR6pfiLzV8qBtR3trFRbIlrI7vo21d2tFtuS8
PfAR+9VHkeOdjVKDbu1sl7YycWz03xq4cM9XPFhvrobeFXb5OFwDwLWn4DZR5ZWY
iJSMJkaBSww=
=F6UW
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
Commit be86781497 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The support outputs struct for overlay managers is incorrect for OMAP4. Make
these changes:
- DPI isn't supported via the LCD1 overlay manager, remove DPI as a supported
output.
- the TV manager can suppport DPI, but the omapdss driver doesn't support that
yet, we require some muxing at the DSS level, and we also need to configure
the hdmi pll in the DPI driver so that the TV manager has a pixel clock. We
don't support that yet.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This driver uses omap_dss_device that it gets from a board file through
SPI platfrom_data pointer to pass data from SPI to DSS portion of the
driver by using dev_set_drvdata(). However this trick no longer works,
as DSS core no longer uses omap_dss_device from a board file to create
the real device, so use a global pointer to accomplish this instead,
like other SPI panel drivers do.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix the following build regression in 3.9-rc1 by including
<mach/hardware.h>:
drivers/video/omap/omapfb_main.c: In function 'set_fb_var':
drivers/video/omap/omapfb_main.c:505:3: error: implicit declaration of function 'cpu_is_omap15xx' [-Werror=implicit-function-declaration]
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The issue fixed by this patch manifests only then using X11
with mxsfb driver. The X11 will display either shifted image
or otherwise distorted image on the LCD.
The problem is that the X11 tries to reconfigure the framebuffer
and along the way calls fb_ops.fb_set_par() with X11's desired
configuration values. The field of particular interest is
fb_info->var.sync which contains non-standard values if
configured by kernel. These are either FB_SYNC_DATA_ENABLE_HIGH_ACT,
FB_SYNC_DOTCLK_FAILING_ACT or both, depending on the platform
configuration. Both of these values are defined in the
include/linux/mxsfb.h file.
The driver interprets these values and configures the LCD controller
accordingly. Yet X11 only has access to the standard values for this
field defined in include/uapi/linux/fb.h and thus, unlike kernel,
omits these special values. This results in distorted image on the
LCD.
This patch moves these non-standard values into new field of the
mxsfb_platform_data structure so the driver can in turn check this
field instead of the video mode field for these specific portions.
Moreover, this patch prefixes these values with MXSFB_SYNC_ prefix
instead of FB_SYNC_ prefix to prevent confusion of subsequent users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM <linux-arm-kernel@lists.infradead.org>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Lothar Waßmann <LW@karo-electronics.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
These are part of a longer series that has been submitted some time
ago for the frame buffer tree, but it was never accepted there.
The first two of the five patches are bug fixes, so let's merge
this through arm-soc to get a working 3.9 kernel for at91.
* commit '67cf9c0a':
ARM: at91: fix LCD-wiring mode
atmel_lcdfb: fix 16-bpp modes on older SOCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.
Use SOC-type to determine the pixel layout.
Tested on at91sam9263 and at91sam9g45.
Cc: <stable@vger.kernel.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit 16559ae4 (kgdb: remove #include <linux/serial_8250.h> from kgdb.h)
had a side effect of breaking omap1_defconfig build as some headers
were included indirectly:
arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function)
...
This worked earlier as linux/serial_8250.h included linux/serial_core.h,
via linux/serial_8250.h from linux/kgdb.h. Fix this by including the
necessary headers directly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
dri= ver and current sinks. This patch enables LP8788 backlight module.
(Brightness mode)
The brightness is controlled by PWM input or I2C register.
All modes are supported in the driver.
(Platform data)
Configurable data can be defined in the platform side.
name : backlight driver name. (default: "lcd-backlight")
initial_brightness : initial value of backlight brightness
bl_mode : brightness control by PWM or lp8788 register
dim_mode : dimming mode selection
full_scale : full scale current setting
rise_time : brightness ramp up step time
fall_time : brightness ramp down step time
pwm_pol : PWM polarity setting when bl_mode is PWM based
period_ns : platform specific PWM period value. unit is nano.
The default values are set in case no platform data is defined.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes power_on() call optional. The voltage source can be
provided to some boards using ams369fg06 panel, thus in this case, power
on/off sequence is not necessary.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
A new driver has been added to support the PWM mode of the timer counter
blocks found on Atmel AT91 SoCs. The VT8500 driver now supports changing
the PWM signal polarity and the TI drivers (EHRPWM and ECAP) gained
suspend and resume functionality.
User drivers can now query the core for whether access to a PWM device
will sleep (if the PWM chip is on a slow bus such as I2C or SPI).
The pwm-backlight driver now handles the backlight BL_CORE_FBBLANK state
in addition to the FB layer's blanking states.
To round things off, a few fixes and cleanups are also included.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Fcxi
-----END PGP SIGNATURE-----
Merge tag 'for-3.9-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull PWM changes from Thierry Reding:
"A new driver has been added to support the PWM mode of the timer
counter blocks found on Atmel AT91 SoCs. The VT8500 driver now
supports changing the PWM signal polarity and the TI drivers (EHRPWM
and ECAP) gained suspend and resume functionality.
User drivers can now query the core for whether access to a PWM device
will sleep (if the PWM chip is on a slow bus such as I2C or SPI).
The pwm-backlight driver now handles the backlight BL_CORE_FBBLANK
state in addition to the FB layer's blanking states.
To round things off, a few fixes and cleanups are also included"
* tag 'for-3.9-rc1' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: twl: Use to_twl() instead of container_of()
pwm: tegra: assume CONFIG_OF
pwm_backlight: Validate dft_brightness in main probe function
pwm: Export pwm_{set,get}_chip_data()
pwm: Make Kconfig entries more consistent
pwm: Add can_sleep property to drivers
pwm: Add pwm_can_sleep() as exported API to users
pwm-backlight: handle BL_CORE_FBBLANK state
pwm: pwm-tiecap: Low power sleep support
pwm: pwm-tiehrpwm: Low power sleep support
pwm: pwm-tiehrpwm: Update the clock handling of pwm-tiehrpwm driver
pwm: vt8500: Add polarity support
pwm: vt8500: Register write busy test performed incorrectly
pwm: atmel: add Timer Counter Block PWM driver
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation,
OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee Jones. In
particular, the debugfs and the sysct interfaces got extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core
driver, with a much needed module id lookup code improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the palmas
GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and
Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based
devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a better
card detection code path and now also supports the RTS5227 chipset, thanks
to Wei Wang and Roger Tseng.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BhC1
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS updates from Samuel Ortiz:
"This is the MFD pull request for the 3.9 merge window.
No new drivers this time, but a bunch of fairly big cleanups:
- Roger Quadros worked on a OMAP USBHS and TLL platform data
consolidation, OMAP5 support and clock management code cleanup.
- The first step of a major sync for the ab8500 driver from Lee
Jones. In particular, the debugfs and the sysct interfaces got
extended and improved.
- Peter Ujfalusi sent a nice patchset for cleaning and fixing the
twl-core driver, with a much needed module id lookup code
improvement.
- The regular wm5102 and arizona cleanups and fixes from Mark Brown.
- Laxman Dewangan extended the palmas APIs in order to implement the
palmas GPIO and rt drivers.
- Laxman also added DT support for the tps65090 driver.
- The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra
and Darren Hart.
- Linus Walleij patchset for the ab8500 driver allowed ab8500 and
ab9540 based devices to switch to the new abx500 pin-ctrl driver.
- The max8925 now has device tree and irqdomain support thanks to
Qing Xu.
- The recently added rtsx driver got a few cleanups and fixes for a
better card detection code path and now also supports the RTS5227
chipset, thanks to Wei Wang and Roger Tseng."
* tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits)
mfd: lpc_ich: Use devres API to allocate private data
mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH
mfd: lpc_sch: Accomodate partial population of the MFD devices
mfd: da9052-i2c: Staticize da9052_i2c_fix()
mfd: syscon: Fix sparse warning
mfd: twl-core: Fix kernel panic on boot
mfd: rtsx: Fix issue that booting OS with SD card inserted
mfd: ab8500: Fix compile error
mfd: Add missing GENERIC_HARDIRQS dependecies
Documentation: Add docs for max8925 dt
mfd: max8925: Add dts
mfd: max8925: Support dt for backlight
mfd: max8925: Fix onkey driver irq base
mfd: max8925: Fix mfd device register failure
mfd: max8925: Add irqdomain for dt
mfd: vexpress: Allow vexpress-sysreg to self-initialise
mfd: rtsx: Support RTS5227
mfd: rtsx: Implement driving adjustment to device-dependent callbacks
mfd: vexpress: Add pseudo-GPIO based LEDs
mfd: ab8500: Rename ab8500 to abx500 for hwmon driver
...
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff90702: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
Merge misc patches from Andrew Morton:
- Florian has vanished so I appear to have become fbdev maintainer
again :(
- Joel and Mark are distracted to welcome to the new OCFS2 maintainer
- The backlight queue
- Small core kernel changes
- lib/ updates
- The rtc queue
- Various random bits
* akpm: (164 commits)
rtc: rtc-davinci: use devm_*() functions
rtc: rtc-max8997: use devm_request_threaded_irq()
rtc: rtc-max8907: use devm_request_threaded_irq()
rtc: rtc-da9052: use devm_request_threaded_irq()
rtc: rtc-wm831x: use devm_request_threaded_irq()
rtc: rtc-tps80031: use devm_request_threaded_irq()
rtc: rtc-lp8788: use devm_request_threaded_irq()
rtc: rtc-coh901331: use devm_clk_get()
rtc: rtc-vt8500: use devm_*() functions
rtc: rtc-tps6586x: use devm_request_threaded_irq()
rtc: rtc-imxdi: use devm_clk_get()
rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
rtc: rtc-pcf8583: use dev_warn() instead of printk()
rtc: rtc-sun4v: use pr_warn() instead of printk()
rtc: rtc-vr41xx: use dev_info() instead of printk()
rtc: rtc-rs5c313: use pr_err() instead of printk()
rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
rtc: rtc-ds2404: use dev_err() instead of printk()
rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
...
Getting the brightness value is not critical, no need to read the actual
register value. To simplify it, just return the 'bl->props.brightness'
value. Then, lp855x_read_byte() can be removed, not used any more.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.
Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END
And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At this moment, LP855x device driver has fixed register configuration.
For example, fixed register addresses and values are set on the device
initialization. But new device of LP855x family, LP8557 has different
register map and initialization sequence. To support new device
architecture, initialization process should be changed.
Introduce new structure: lp855x_device_config
=============================================
With lp855x_device_config, device specific features are configurable.
Use configurable function calls and register addresses rather than fixed values.
Change on device initialization
===============================
In old LP855x driver architecture, the device initialization was simple.
- Just update the brightness/device control register/ROM area(optional).
In new LP855x driver architecture, two more works are added - pre_init and
post_init.
Those init functions are optional, used for new device LP8557.
New device initialization flow: generic sequence
=================================================
1) pre_init_device()
2) update the brightness register
3) update the device control register
4) update ROM area if need
5) post_init_device()
Name change
===========
Use generic name 'lp855x_configure()' instead of 'lp855x_init_registers()'.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to return -EIO, because backlight_device_register()
already returns correct error values.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gamma_table has 3 arrays which each hold MAX_GAMMA_LEVEL pointers to int.
The current code sets ->gamma_table_count to 6 on 64bit arches and to 3 on
32 bit arches. It should be 3 on everything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC. Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage. Anyone wishing to use any of those modes
will have to modify the driver.
Tested on sh73a0-based kzm9g board. Only one mode has been tested and
is enabled. That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
