Since commit 654f2b937b ("crypto: caam - allow retrieving 'era' from
register") the CAAM driver is capable of obtaining the era version by
reading the appropriate CAAM registers, so let the CAAM driver discover
the era version in run-time instead of hardcoding such information in the
device tree.
According to Documentation/devicetree/bindings/crypto/fsl-sec4.txt the
'fsl,sec-era' is an optional property and this can be safely removed
now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change adds a number of basic peripherals found on i.MX31 SoC:
* GPIO controllers,
* I2C master controllers,
* SPI master controllers,
* ATA controller,
* SDHC controllers,
* RTC, watchdog and PWM contollers,
* SDMA,
* IRAM,
* NAND and WEIM controllers on EMI.
The added controller devices were tested on Freescale i.MX31 powered
LogicPD Lite SoM and baseboard.
DMA functionality was tested on SDHC and SPI controllers so far,
thus dmas properties are added to those device nodes only.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following DTC warnings are seen with W=1:
arch/arm/boot/dts/imx51-babbage.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dtb: Warning (unique_unit_address): /usbphy/usbphy@0: duplicate unit-address (also used in node /usbphy/usbh1phy@0)
Fix it by moving the USB PHY nodes outside of simple-bus and drop the
unneeded unit-address, which matches the bindings documentation
at Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
While at it rename the USB PHY node to usbphy1 for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The OPP properties, like "operating-points", should either be present
for all the CPUs of a cluster or none. If these are present only for a
subset of CPUs of a cluster then things will start falling apart as soon
as the CPUs are brought online in a different order. For example, this
will happen because the operating system looks for such properties in
the CPU node it is trying to bring up, so that it can create an OPP
table.
Add such missing properties.
Fix other missing properties (like clocks, supply, clock latency) as
well to make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to i.MX6 datasheet, the LDO_1P1's typical
programming operating range is 1.0V to 1.2V, and
the LDO_2P5's typical programming operating range
is 2.25V to 2.75V, correct LDO_1P1 and LDO_2P5's
regulator range settings for i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per Documentation/process/license-rules.rst the SPDX notation for
header file should be /* */ style, so fix it accordingly.
Fixes: 9f30b6b1a9 ("ARM: dts: imx: Add basic dtsi file for imx6sll")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6ULL has different operating ranges than i.MX6UL so add the
operating points for the i.MX6ULL and remove them from board device
trees. A 25mV offset is added to the minimum allowed values like for the
i.MX6UL.
The valid frequencies are now selected by the cpufreq driver according
to ratings stored in fuses since commit 0aa9abd4c2 ("cpufreq: imx6q:
check speed grades for i.MX6ULL")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This was fixed in
645a397, so correct the RDU1 DT to apply the inversion to the
correct axis.
Tested on Zii RDU1 00-5105-30 rev B
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This renames usbphy nodes 2 & 3, so that they follow the same
format as usbphy node 0 & 1 from imx53.dtsi.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add information about 3V3 power rail to avoid kernel warnings,
that dummy regulators have been added.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pinctrl_usbh1reg defines pinmux setting for reset GPIO used by
usbh1phy, but is not referenced by that node. Fix that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements power button control compatible with
the rave-sp-pwrbutton driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RAVE SP found on RDU2 implements backlight control compatible with the
rave-sp-backlight driver. Add a node to make it availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ZII's RDU1s come with up to 3 EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The hog pinctrl hog is meant for pins that do not have an
associated driver.
The MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK pin is the one that
provides the MCLK signal to the SGTL5000 codec, so a
better represenation is to move it under the codec node.
While at it, change the pinctrl value from 0x80000000 to the
POR reset value of register IOMUXC_SW_PAD_CTL_PAD_GPIO_0.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
iMX50 pin mux options for pads KEY_COL2 and KEY_COL3 allow muxing the same
KEY_COL instances as the pad name. Fix typos shifting KEY_COL instances.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently when trying to use the 'devmem' tool to read/write
registers the following bus error is observed:
[ 82.689185] Unhandled fault: external abort on non-linefetch (0x1018) at 0xb6ff10c4
[ 82.697071] pgd = (ptrval)
[ 82.699920] [b6ff10c4] *pgd=a87c5831, *pte=73fa8383, *ppte=73fa8a33
Bus error
Add the aipstz nodes, so that the following function from
imx51_dt_init() can work properly:
imx_aips_allow_unprivileged_access("fsl,imx51-aipstz");
After adding these nodes, 'devmem' tool can work correctly,
which is very useful for debugging purposes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was removed in commit 5eaeaccdae ("ARM: dts: imx7d-sdb: Pass
'enable-gpios' and 'power-supply' properties") with a note claiming that
GPIO1_IO01 is connected to a pin labeled as "PWREN" on the connector.
Despite that label this pin does actually work as a PWM controlling
brightness. So restore pwm functionality.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL uses same SRC module as i.MX51, add "fsl,imx51-src"
compatible string to enable SRC driver to support setting
CPU resume address for cpu-idle and suspend/resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RIoTboard debug uart is connected to serial1.
Add a chosen property in the DTS so OS knows what serial port to use for
the console.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two different regulators are defined with the same name and label but
distinct properties.
The first definition was added with the first board dts and the second
was added when upstream added flexcan support.
Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.
The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer
Added under i2cmux/i2c@1 because they're not otherwise accessible.
These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452
Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.
This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB OTG power is switched on when the GPIO is pulled low.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To match the convention, move regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To match the convention, move all regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure that MX51_PAD_GPIO1_1 does not remain configure as
ALT0/SD1_WP (it is out of reset). This is needed because of external
pull-up resistor attached to that pad that, when left unchanged, will
drive SD1_WP high preventing eSDHC1/eMMC from working correctly.
To fix that add a pinmux configuration line configureing the pad to
function as a GPIO. While we are at it, add a corresponding
output-high GPIO hog in an effort to minimize current consumption.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit provides support for HSC and DDC boards from
Kieback&Peter GmbH vendor.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
