This patch adds basic ethtool support to the device to allow
for configuration.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With recent changes, need to bump the driver version to reflect the
changes.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the redundant 'igc_get_phy_id_base' method and use
the 'igc_get_phy_id' method directly instead.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the redundant 'igc_read_mac_addr_base' method and use
the 'igc_read_mac_addr' method directly instead.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.
[ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.174495] 8021q: 802.1Q VLAN Support v1.8
[ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 30.898564] netpoll: netconsole: local port 6666
[ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[ 30.898567] netpoll: netconsole: interface 'eth1'
[ 30.898568] netpoll: netconsole: remote port 6666
[ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[ 30.917747] console [netcon0] enabled
[ 30.917749] netconsole: network logging started
[ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the 'igc_get_link_up_info_base method' from igc_base.c file.
Use the 'igc_get_speed_and_duplex_copper' method directly and reduce
the code redundancy.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused igc_adv_data_desc definition from igc_base.h file.
Descriptors definition will be added per demand.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The change is based on the issue found by Kangjie Lu <kjlu@umn.edu> where
we not checking the return value of a register read/write which could result
in a NULL pointer dereference if the read/write fails.
Since we are only trying to disable the far-end loopback, if the read
and write of register fails, we do not want to bail out of the function.
We just want to log that it failed to disable and continue on.
CC: Sasha Neftin <sasha.neftin@intel.com>
CC: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function comment for fm10k_iov_msg_msix_pf has an extra space in
a sentence, which is unnecessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_reset_hw_82599() resets the value of hw->mac.num_rar_entries to
pre-defined value of 128. Let's get rid of that hardcoded literal, and use
IXGBE_82599_RAR_ENTRIES instead, the same way the normal initialization
path does.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant igc_check_for_link_base code and replace it with
an igc_check_for_copper_link method.
Fix duplication of IGC_ADVTXD_PAYLEN_SHIFT mask declaration.
Remove obsolete IGC_SCVPC register definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Address community comment.
Remove the unreachable code leads to the static checker warning.
PHY functionality will be added later per demand.
Reported by Dan Carpenter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e sets different WoL settings in system suspend callback and
runtime suspend callback.
The suspend direct complete optimization leaves e1000e in runtime
suspended state with wrong WoL setting during system suspend.
To fix this, we need to disable suspend direct complete optimization to
let e1000e always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In packets that need to be decaped the internal headers
have to be checked, not the external ones.
Fixes: bdd66ac0ae ("net/mlx5e: Disallow TC offloading of unsupported match/action combinations")
Signed-off-by: Guy Shattah <sguy@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The match level computed by the driver gets to be wrong for decap
rules with wildcarded inner packet match such as:
tc filter add dev vxlan_sys_4789 protocol all parent ffff: prio 2 flower
enc_dst_ip 192.168.0.9 enc_key_id 100 enc_dst_port 4789
action tunnel_key unset
action mirred egress redirect dev eth1
The FW errs for a missing matching meta-data indicator for the outer
headers (where we do have a match), and a wrong matching meta-data
indicator for the inner headers (where we don't have a match).
Fix that by taking into account the matching on the tunnel info and
relating the match level of the encapsulated packet to the firmware
inner headers indicator in case of decap.
As for vxlan we mandate a match on the tunnel udp dst port, and in general
we practically madndate a match on the source or dest ip for any IP tunnel,
the fix was done in a minimal manner around the tunnel match parsing code.
Fixes: d708f90298 ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Slava Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
At Innova IPsec TX offload data path a special software parser metadata
is used to pass some packet attributes to the hardware, this metadata
is passed using the Ethernet control segment of a WQE (a HW descriptor)
header.
The cited commit might nullify this header, hence the metadata is lost,
this caused a significant performance drop during hw offloading
operation.
Fix by restoring the metadata at the Ethernet control segment in case
it was nullified.
Fixes: 37fdffb217 ("net/mlx5: WQ, fixes for fragmented WQ buffers API")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Sven Auhagen reports that if he changes a SFP+ module for a SFP module
on the Macchiatobin Single Shot, the link does not come back up. For
Sven, it is as easy as:
- Insert a SFP+ module connected, and use ping6 to verify link is up.
- Remove SFP+ module
- Insert SFP 1000base-X module use ping6 to verify link is up: Link
up event did not trigger and the link is down
but that doesn't show the problem for me. Locally, this has been
reproduced by:
- Boot with no modules.
- Insert SFP+ module, confirm link is up.
- Replace module with 25000base-X module. Confirm link is up.
- Set remote end down, link is reported as dropped at both ends.
- Set remote end up, link is reported up at remote end, but not local
end due to lack of link interrupt.
Fix this by setting up both GMAC and XLG interrupts for port 0, but
only unmasking the appropriate interrupt according to the current mode
set in the mac_config() method. However, only do the mask/unmask
dance when we are really changing the link mode to avoid missing any
link interrupts.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phy_interface_mode_is_8023z() helper for detecting interface
modes that use 802.3z serial encoding. This is equivalent to testing
for both 1000base-X and 2500base-X.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fixed-link configurations to nixge driver.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make MDIO child optional and only instantiate the
MDIO bus if the child is actually present.
There are currently no (in-tree) users of this
binding; all (out-of-tree) users use overlays that
get shipped together with the FPGA images that contain
the IP.
This will significantly increase maintainabilty
of future revisions of this IP.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tab before '}' and keep the code style consistent.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7763 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7734 SoC manual describes the Ether MAC's RX checksum offload
the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (R8A77980) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Mobile A1 (R8A7740) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MAC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RZ/A1H (R7S721000) SoC manual describes the Ether MAC's RX checksum
offload the same way as it's implemented in the EtherAVB MACs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the RX checksum offload. This is enabled by default and
may be disabled and re-enabled using 'ethtool':
# ethtool -K eth0 rx off
# ethtool -K eth0 rx on
Some Ether MACs provide a simple checksumming scheme which appears to be
completely compatible with CHECKSUM_COMPLETE: sum of all packet data after
the L2 header is appended to packet data; this may be trivially read by
the driver and used to update the skb accordingly. The same checksumming
scheme is implemented in the EtherAVB MACs and now supported by the 'ravb'
driver.
In terms of performance, throughput is close to gigabit line rate with the
RX checksum offload both enabled and disabled. The 'perf' output, however,
appears to indicate that significantly less time is spent in do_csum() --
this is as expected.
Test results with RX checksum offload enabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 933.93
[ perf record: Woken up 8 times to write data ]
[ perf record: Captured and wrote 1.955 MB perf.data (41940 samples) ]
~/netperf-2.2pl4# perf report
Samples: 41K of event 'cycles:ppp', Event count (approx.): 9915302763
Overhead Command Shared Object Symbol
9.44% netperf [kernel.kallsyms] [k] __arch_copy_to_user
7.75% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
6.31% swapper [kernel.kallsyms] [k] default_idle_call
5.89% swapper [kernel.kallsyms] [k] arch_cpu_idle
4.37% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
4.02% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.52% netperf [kernel.kallsyms] [k] preempt_count_sub
1.81% netperf [kernel.kallsyms] [k] tcp_recvmsg
1.80% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irqres
1.78% netperf [kernel.kallsyms] [k] preempt_count_add
1.36% netperf [kernel.kallsyms] [k] __tcp_transmit_skb
1.20% netperf [kernel.kallsyms] [k] __local_bh_enable_ip
1.10% netperf [kernel.kallsyms] [k] sh_eth_start_xmit
Test results with RX checksum offload disabled:
~/netperf-2.2pl4# perf record -a ./netperf -t TCP_MAERTS -H 192.168.2.4
TCP MAERTS TEST to 192.168.2.4
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
131072 16384 16384 10.01 932.04
[ perf record: Woken up 14 times to write data ]
[ perf record: Captured and wrote 3.642 MB perf.data (78817 samples) ]
~/netperf-2.2pl4# perf report
Samples: 78K of event 'cycles:ppp', Event count (approx.): 18091442796
Overhead Command Shared Object Symbol
7.00% swapper [kernel.kallsyms] [k] do_csum
3.94% swapper [kernel.kallsyms] [k] sh_eth_poll
3.83% ksoftirqd/0 [kernel.kallsyms] [k] do_csum
3.23% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irq
2.87% netperf [kernel.kallsyms] [k] __arch_copy_to_user
2.86% swapper [kernel.kallsyms] [k] arch_cpu_idle
2.13% swapper [kernel.kallsyms] [k] default_idle_call
2.12% ksoftirqd/0 [kernel.kallsyms] [k] sh_eth_poll
2.02% swapper [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.84% swapper [kernel.kallsyms] [k] __softirqentry_text_start
1.64% swapper [kernel.kallsyms] [k] tick_nohz_idle_exit
1.53% netperf [kernel.kallsyms] [k] _raw_spin_unlock_irq
1.32% netperf [kernel.kallsyms] [k] preempt_count_sub
1.27% swapper [kernel.kallsyms] [k] __pi___inval_dcache_area
1.22% swapper [kernel.kallsyms] [k] check_preemption_disabled
1.01% ksoftirqd/0 [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
The above results collected on the R-Car V3H Starter Kit board.
Based on the commit 4d86d38186 ("ravb: RX checksum offload")...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 62e04b7e0e ("sh_eth: rename 'sh_eth_cpu_data::hw_crc'") renamed
the field to 'hw_checksum' for the Ether DMAC "intelligent checksum",
however some Ether MACs implement a simpler checksumming scheme, so that
name now seems misleading. Rename that field to 'csmr' as the "intelligent
checksum" is always controlled by the CSMR register.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom STB chips support a deep sleep mode where all register
contents are lost. Because we were stashing the MagicPacket password
into some of these registers a suspend into that deep sleep then a
resumption would not lead to being able to wake-up from MagicPacket with
password again.
Fix this by keeping a software copy of the password and program it
during suspend.
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{t4/t4_vf}_change_mac() API's were only doing additions to MPS_TCAM.
This will fail, when the number of tcam entries is limited particularly
in vf's.
This fix programs hash region with the mac address, when TCAM
addtion fails for {t4/t4vf}_change_mac(). Since the locally maintained
driver list for hash entries is shared across mac_{sync/unsync}(),
added an extra parameter if_mac to track the address added thorugh
{t4/t4vf}_change_mac()
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
A return statment is not indented correctly, fix this by adding an
extra tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An if statement is indented one level too deep, fix this by removing
the extra tabs. Also add some spaces to the dev_warn arguments to clean
up checkpatch warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to bfa_ioc_pf_failed is indented too far, fix this by
removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment to size is indented too far, fix this and join
two lines into one.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA engine is a separate entity altogether, and this allows the DMA
controller's address to float elsewhere in the FPGA's map.
Signed-off-by: Alex Williams <alex.williams@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_wol_pll_power_down() is used in only one place and removing it
makes the code simpler and better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating the available MAC VLAN table counts,
MAC VLAN table entry count function adds
operation 0 value protection measures.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to prevent the variable anomaly from being larger than desc_num,
the upper limit judgment condition becomes >=.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables vlan filter, and adds vlan device, it won't
notify the driver the update the vlan filter. In this case, when
user enables vlan filter again, the packets with new vlan tag
will be filtered by vlan filter.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple macros with the largest number of TCs in the system,
optimized to HCLGE_MAX_TC_NUM.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Run ethtool ethx when displaying device information in VF，
the supported port and link mode items will be empty.
This patch fixes it.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the TC is enabled, we need to check whether the buffer is enough,
otherwise it may lead to a wrong -ENOMEM case.
Fixes: 9ffe79a9c2 ("net: hns3: Support for dynamically assigning tx buffer to TC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not change the code logic. There are some same
set_bit statements called by add/rm_uc/mc_addr_common, and move
this statements into hclge_prepare_mac_addr to reduce duplicate
code.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For simplifying the code, this patch adds hclge_cmd_check_retval() to
check the return value of the command.
Also, according the IMP's description, when there are several descriptors
in a command, then the IMP will save the return value on the last
description, so hclge_cmd_check_retval() just check the last one for this
case.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four steps to calcuate the rx private buffer, each step
can be done in a function to avoid code duplication and aid code
readability.
This patch adds three separate functions do the job. Also, the
function name more or less make the comment redundant, so remove
some obvious comment.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second parameter to the hook function set_gro_en is always passed in
true/false, so modify it's type from int to bool.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 supports setting rx-usecs|tx-usecs as 0, but it will not
update dynamically when adaptive-tx or adaptive-rx is enable.
This patch removes the Redundant check.
Fixes: a95e1f8666 ("net: hns3: change the time interval of int_gl calculating")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same code style for rx_group and tx_group in the
hns3_update_new_int_gl().
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-02-01
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) introduce bpf_spin_lock, from Alexei.
2) convert xdp samples to libbpf, from Maciej.
3) skip verifier tests for unsupported program/map types, from Stanislav.
4) powerpc64 JIT support for BTF line info, from Sandipan.
5) assorted fixed, from Valdis, Jesper, Jiong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following ALU32 logic shift supports are missing:
BPF_ALU | BPF_LSH | BPF_X
BPF_ALU | BPF_RSH | BPF_X
BPF_ALU | BPF_RSH | BPF_K
For BPF_RSH | BPF_K, it could be implemented using NFP direct shift
instruction. For the other BPF_X shifts, NFP indirect shifts sequences need
to be used.
Separate code-gen hook is assigned to each instruction to make the
implementation clear.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Shifts by zero do nothing, and should be treated as nops.
Even though compiler is not supposed to generate such instructions and
manual written assembly is unlikely to have them, but they are legal
instructions and have defined behavior.
This patch correct existing shifts code-gen to make sure they do nothing
when shift amount is zero except when the instruction is ALU32 for which
high bits need to be cleared.
For shift amount bigger than type size, already, NFP JIT back-end errors
out for immediate shift and only low 5 bits will be taken into account for
indirect shift which is the same as x86.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Report versions of firmware components using the new NSP command.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the FW versions with the new command.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report information about the hardware.
RFCv2:
- add defines for board IDs which are likely to be reusable for
other drivers (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the basic info through new devlink info API.
RFCv2:
- add driver name;
- align serial to core changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kmalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is
finding the size of a structure that has a zero-sized array at
the end, along with memory for some number of elements for that
array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is
finding the size of a structure that has a zero-sized array at
the end, along with memory for some number of elements for that
array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does
not set skb->ip_summed. So IPv6 rx checksum is not offloaded.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should return -ENOMEM if the kcalloc() fails.
Fixes: d174ea75c9 ("net: hns3: add statistics for PFC frames and MAC control frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "p" buffer is 0x4000 bytes long. B3_RI_WTO_R1 is 0x190. The value
of "regs->len" is in the 1-0x4000 range. The bug here is that
"regs->len - B3_RI_WTO_R1" can be a negative value which would lead to
memory corruption and an abrupt crash.
Fixes: c3f8be9618 ("[PATCH] skge: expand ethtool debug register dump")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling firmware to allocate a CP ring or NQ, an interrupt associated
with that ring may be generated immediately before the doorbell is even
setup after the firmware call returns. When servicing the interrupt, the
driver may crash when trying to access the doorbell.
Fix it by disabling interrupt on that vector until the doorbell is
set up.
Fixes: 697197e5a1 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL handling for the RTL8168 family is a little bit tricky because of
different types of broken BIOS and/or chip quirks.
Two known issues:
1. Network properly resumes from suspend only if WoL is enabled in the chip.
2. Some notebooks wake up immediately if system is suspended and network
device is wakeup-enabled.
Few patches tried to deal with this:
7edf6d314c ("r8169: disable WOL per default")
18041b5236 ("r8169: restore previous behavior to accept BIOS WoL
settings")
Currently we have the situation that the chip WoL settings as set by
the BIOS are respected (to prevent issue 1), but the device doesn't get
wakeup-enabled (to prevent issue 2).
This leads to another issue:
If systemd is told to set WoL it first checks whether the requested
settings are active already (and does nothing if yes). Due to the chip
WoL flags being set properly systemd assumes that WoL is configured
properly in our case. Result is that device doesn't get wakeup-enabled
and WoL doesn't work (until it's set e.g. by ethtool).
This patch now:
- leaves the chip WoL settings as is (to prevent issue 1)
- keeps the behavior to not wakeup-enable the device initially
(to prevent issue 2)
- In addition we report WoL as being disabled in get_wol, matching
that device isn't wakeup-enabled. If systemd is told to enable WoL,
it will therefore detect that it has to do something and will
call set_wol.
Of course the user still has the option to override this with
e.g. ethtool.
v2:
- Don't just exclude __rtl8169_get_wol() from compiling, remove it.
v3:
- adjust commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In stmmac xmit callback we use a different flow for TSO packets but TSO
xmit callback is not disabling the EEE mode.
Fix this by disabling earlier the EEE mode, i.e. before calling the TSO
xmit callback.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of TSO enabled channels in HW can be different than the
number of total channels. There is no way to determined, at runtime, the
number of TSO capable channels and its safe to assume that if TSO is
enabled then at least channel 0 will be TSO capable.
Lets always send TSO packets from Queue 0.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.
This way we can still use the coalesce command in PCI based setups.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In orginal codes, driver always enables flow director when
intializing. When user disable flow director with command
ethtool -K, the flow director will be enabled again after
resetting.
This patch fixes it by only enabling it when first initialzing.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is resetting, it can't communicate to PF with mailbox msg.
This patch adds reset state checking before sending keep alive msg
to PF.
Fixes: a6d818e31d ("net: hns3: Add vport alive state checking support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 VF driver support NIC and Roce, hdev stores NIC
handle and Roce handle, should use correct parameter for
container_of.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hclge_init_umv_space() failed in the hclge_init_ae_dev(),
we should undo all the operation which has been done successfully,
the last success operation maybe hclge_mac_mdio_config(), so if
hclge_init_umv_space() failed, we also need to undo it.
Fixes: 288475b2ad01 ("{topost} net: hns3: refine umv space allocation")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rss result is more uniform when use recommended hash key from
microsoft, instead of the one generated by netdev_rss_key_fill().
Also using hash algorithm "xor" is better than "toeplitz".
This patch modifies the default hash key and hash algorithm.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is unloading, if a global reset occurs,
unmap_ring_from_vector() in the hns3_nic_uninit_vector_data() will
fail, and hns3_nic_uninit_vector_data() just return. There may be
some netif_napi_del() not be done.
Since hardware will unmap all ring while resetting, so
hns3_nic_uninit_vector_data() should ignore this error, and do the
rest uninitialization.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF shares the same TC config as PF, the business
running on PF and VF must have samiliar module.
For simplicity, we are not considering VF sharing the same tc
configuration as PF use case, so this patch removes the support
of TC configuration from VF and forcing VF to just use single
TC.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hnae3_register_ae_dev() may fail, and it should return a error code
to its caller, so change hnae3_register_ae_dev() return type to int.
Also, when hnae3_register_ae_dev() return error, hns3_probe() should
do some error handling and return the error code.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_close() stop the netdev and the service base on the netdev
will stop. But ndev->netdev_ops->ndo_stop() may only stop HW
and stack queue, the service base on the netdev can still work.
Fixes: 5668abda09 ("net: hns3: add support for set_ringparam")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the .get_regs_len and .get_regs were missed
assigned. This patch fixes it.
Fixes: 1600c3e5f2 ("net: hns3: Support "ethtool -d" for HNS3 VF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Union l3_hdr_info and l4_hdr_info have already been defined in
the hns3_enet.h, so it is unnecessary to define them elsewhere.
This patch removes the redundant definition, and reuses the one
defined in the hns3_enet.h.
Signed-off-by: liyongxin <liyongxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Mediatek MT7621 SoC contains the same ethernet hardware module as
used on a number of other MediaTek SoC parts. There are some minor
differences to deal with but we can use the same driver to support
them all.
This patch is based on work by Bjørn Mork <bjorn@mork.no>, and his
original patch is at:
3293bc63f5
There is an additional compatible devicetree type added, and the primary
change to the code required is to support a single interrupt (for both
RX and TX interrupts).
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[gerg@kernel.org: rebase to mainline and irq handler fix]
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.
Co-authored-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some visibility to the rule addition process and trace whenever rule
spilled into C-TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only ERP mask masked bits in key are considered for
the hashtable key. That leads to false negative collisions
and fallbacks to C-TCAM in case two keys differ only in delta bits.
Fix this by taking full encoded key as a hashtable key,
including delta bits.
Reported-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register devlink_port with devlink and create initial port params
table for bnxt_en. The table consists of a generic parameter:
wake_on_lan: Enables Wake on Lan for this port when magic packet
is received with this port's MAC address using ACPI pattern.
If enabled, the controller asserts a wake pin upon reception of
WoL packet. ACPI (Advanced Configuration and Power Interface) is
an industry specification for the efficient handling of power
consumption in desktop and mobile computers.
v2->v3:
- Modify bnxt_dl_wol_validate(), to throw error message when user gives
value other than DEVLINK_PARAM_WAKE_MAGIC ot to disable WOL.
- Use netdev_err() instead of netdev_warn(), when devlink_port_register()
and devlink_port_params_register() returns error. Also, don't log rc
in this message.
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb should be freed by dev_consume_skb_any() in b44_start_xmit()
when bounce_skb is used. The skb is be replaced by bounce_skb, so the
original skb should be consumed(not drop).
dev_consume_skb_irq() should be called in b44_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in cp_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that the basic port information could have
changed since we first read it.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler contains a workaround for RX hang applicable
to Zynq and AT91RM9200 only. Subsequent versions do not need this
workaround. This workaround unnecessarily resets RX whenever RX used
bit read is observed, which can be often under heavy traffic. There
is no other action performed on RX UBR interrupt. Hence introduce a
CAPS mask; enable this interrupt and workaround only on affected
versions.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the code that was incorrectly interpreting the rx checksum validation
status from hardware, and updating kernel that the packet arrived with
correct checksum though the packet arrived with incorrect checksum and
hardware also indicated checksum is not correct.
Signed-off-by: Veerasenareddy Burru <vburru@marvell.com>
Acked-by: Derek Chickles <dchickles@marvell.com>
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in cpmac_end_xmit() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in bmac_txdma_intr() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in amd8111e_tx() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in ace_tx_int() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-01-29
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Teach verifier dead code removal, this also allows for optimizing /
removing conditional branches around dead code and to shrink the
resulting image. Code store constrained architectures like nfp would
have hard time doing this at JIT level, from Jakub.
2) Add JMP32 instructions to BPF ISA in order to allow for optimizing
code generation for 32-bit sub-registers. Evaluation shows that this
can result in code reduction of ~5-20% compared to 64 bit-only code
generation. Also add implementation for most JITs, from Jiong.
3) Add support for __int128 types in BTF which is also needed for
vmlinux's BTF conversion to work, from Yonghong.
4) Add a new command to bpftool in order to dump a list of BPF-related
parameters from the system or for a specific network device e.g. in
terms of available prog/map types or helper functions, from Quentin.
5) Add AF_XDP sock_diag interface for querying sockets from user
space which provides information about the RX/TX/fill/completion
rings, umem, memory usage etc, from Björn.
6) Add skb context access for skb_shared_info->gso_segs field, from Eric.
7) Add support for testing flow dissector BPF programs by extending
existing BPF_PROG_TEST_RUN infrastructure, from Stanislav.
8) Split BPF kselftest's test_verifier into various subgroups of tests
in order better deal with merge conflicts in this area, from Jakub.
9) Add support for queue/stack manipulations in bpftool, from Stanislav.
10) Document BTF, from Yonghong.
11) Dump supported ELF section names in libbpf on program load
failure, from Taeung.
12) Silence a false positive compiler warning in verifier's BTF
handling, from Peter.
13) Fix help string in bpftool's feature probing, from Prashant.
14) Remove duplicate includes in BPF kselftests, from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache number of fragments in the skb locally as in case
of linear skb (with zero fragments), tx completion
(or freeing of skb) may happen before driver tries
to get number of frgaments from the skb which could
lead to stale access to an already freed skb.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.
In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF is always configured to drop control frames
(with reserved mac addresses) but to work LACP
on the VFs, it would require LACP control frames
to be forwarded or transmitted successfully.
This patch fixes this in such a way that trusted VFs
(marked through ndo_set_vf_trust) would be allowed to
pass the control frames such as LACP pdus.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running tx switched traffic between VNICs
created via a bridge(to which VFs are added),
adapter drops the unicast packets in tx flow due to
VNIC's ucast mac being unknown to it. But VF interfaces
being in promiscuous mode should have caused adapter
to accept all the unknown ucast packets. Later, it
was found that driver doesn't really configure tx
promiscuous mode settings to accept all unknown unicast macs.
This patch fixes tx promiscuous mode settings to accept all
unknown/unmatched unicast macs and works out the scenario.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_broadcast_packet() expands to compare_ether_addr() which doesn't
exist since commit 7367d0b573 ("drivers/net: Convert uses of
compare_ether_addr to ether_addr_equal"). It turns out it's actually not
used.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <albin_yang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more extack messages that let the user know why VXLAN offload
failed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the struct to the place where they belong, alongside with the rest
of the MR code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to pass ruleset/group and chunk pointers on action_replace call
path, nobody uses them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hns driver of earlier devices, when autoneg off, restart autoneg
will return -EINVAL, so make the hns driver for the latest devices
do the same.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns enet driver, we use of_parse_handle() to get hold of the
device node related to "ae-handle" but we have missed to put
the node reference using of_node_put() after we are done using
the node. This patch fixes it.
Note:
This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217
Fixes: 48189d6aaf ("net: hns: enet specifies a reference to dsaf")
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcS2rdAAoJEEg/ir3gV/o+CZ8IAMX4yWUWjzgrIDdOc1OEgHJQ
FDCMtTDm/I+m1UInAgoigRia2RyIL99N81Vrx+p+otCOml/U5IXPt5tuJfSNQYZ3
p9MibQSXtKJ9jhowOVZdYlTx9CXti75BS45wHKZPlL7V+gCC2Q7/8aviuRlkQKAN
4pQNDreNiiB8PznXG/yCyzEu0Kc9M/Bv89xdLynVpDTxBfEfI8xSv4PttUcAxaQ5
Fs/489wuODyhAczOquQj1dvn61zUamaPp6z0h+GbZOCQv0AO7ABRZl+7o5C5r+rA
i7R4ak6WIgW3snIzhCdpynPfas8kUIvxJjkNCZuoFsefrBRsNv5RvtfCkuzyms4=
=3epF
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-01-25
This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
Please pull and let me know if there is any problem.
For -stable v4.13
('net/mlx5e: Allow MAC invalidation while spoofchk is ON')
For -stable v4.18
('Revert "net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager"')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If fill_level was not zero and status was not BUSY,
result of "tx_prod - tx_cons - inuse" might be zero.
Subtracting 1 unconditionally results invalid negative return value
on this case.
Make sure not to return an negative value.
Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp>
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Reviewed-by: Dalon L Westergreen <dalon.westergreen@linux.intel.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atl2_xmit_frame() should call dev_consume_skb_any() when the
transmission is successful. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements code-gen for new JMP32 instructions on NFP.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The LAN743x includes on chip One-Time-Programmable (OTP) memory.
This patch extends the ethtool EEPROM read/write interface to
access OTP memory space.
The currently existing interface is limited, as it does not
allow OTP read, and OTP writes are restricted to
offset==0, length==512, and data[0]==0xF3.
This patch removes these restrictions and adds a private flag
called OTP_ACCESS, which is used to switch between EEPROM, and
OTP modes.
The private flag OTP_ACCESS is configurable through the
ethtool --set-priv-flags command.
And visible through the
ethtool --show-priv-flags command.
By default OTP_ACCESS is false, and there for previously existing
EEPROM commands will work exactly the same. However now access to
OTP requires one extra step of setting OTP_ACCESS to true. This
flag controls the read, write, and length reporting, functions
of ethtool.
EEPROM presence is not checked when setting or clearing this flag.
If the EEPROM is not present, the user, as before, will need to
diagnose that using existing read and write function of ethtool,
while OTP_ACCESS is false.
Updates for V2:
Added comments as to why this patch is needed.
Added comments explaining that EEPROM presence is not check
when setting or clearing the OTP_ACCESS flag.
Added length checking to all otp/eeprom read/write functions.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF can receive packets of other functions when in promisc
mode. It's not safe, so don't allow VF to enable promisc
mode.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds initialization for nic state, sets flag
HNS3_NIC_STATE_DOWN when initialize, clears it before
vectors and napi being enabled in the hns3_nic_net_up(),
and sets it back in the error handler.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single transmit packet can span up to 8 descriptors according
to the HW limit. If a skb has more than 8 frags, driver uses
skb_copy to get a new skb which has less frags.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns3_client_setup_tc in enet is for updating TC configuration to
stack, and hclge_setup_tc in hclge_dcb is mainly for setting the
configuration to hardware.
This patch removes the hns3_nic_set_real_num_queue from
hns3_setup_tc in enet, and call hclge_client_setup_tc to update
TC configuration to stack with netdev down, because the netdev
down operation is done in hclge_dcb now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After doing down/uninit/init/up in hclge_dcb, it is not necessary
to call dcb_ops->map_update in enet, so hclge_map_update can be
called directly in hclge_dcb.
This is for preparing to call hns3_nic_set_real_num_queue with
netdev down when user changes mqprio configuration.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user changes the mqprio configuration, enet need to be
uninited and inited besides down'ed and up'ed, because the queue
num may change when the TC num changes.
Also, it is more suitable to do the down/unint/init/up operation
in hclge module using hclge_notify_client, because this config
change may affect PF and its VF.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After setting the serdes loopback, you need to determine
the status of the MAC negotiation. If a status exception
is obtained after 200ms, a timeout error is returned.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, vlan filter is always bypassed when enable
broadcast promisc mode. In this case, broadcast packets with
any vlan id can be accpeted. We should disable broadcast promisc
mode until user want enable it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current code, it always return 0, even loopback mode setting failed.
It's incorrect. This patch fixes return value handle for loopback test.
Fixes: 0f29fc23b2 ("net: hns3: Fix for loopback selftest failed problem")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hclge_ieee_setets returns error directly when there is
error, which may cause netdev not up problem.
This patch adds some error handling when setting ETS configuration
fails.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unload hns3 driver, we should clear the pci private data.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet statistics for netdev should not include the packets dropped
by hardware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EEE support for RTL8168f to the recently added EEE handling
framework in the driver. This patch leaves the chip defaults, means
EEE typically is disabled initially and it's up to the user to enable
it via ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable EEE per default on chip versions from RTL8168g.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the general framework to deal with EEE in this driver
plus EEE support for chip versions from RTL8168g. We don't touch the
default chip settings, therefore EEE will usually be disabled and it's
up to the user to enable it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Representors software stats are basic, this patch is reusing the
mlx5e_fold_sw_stats in representors, which sums up the basic stats64 for a
mlx5e netdevice.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This behavior is already adopted for all other cases in the cited patch.
The representor's functions were missed, here we modify the them to
behave similarly.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5e_grp_sw_update_stats can be called from two threads,
1) ndo_get_stats64
2) get_ethtool_stats
For this reason and to minimize concurrency issue impact on 64bit machines
mlx5e_grp_sw_update_stats folds the software stats into a temporary
variable then copies it to the global driver stats, both ethtool and ndo
statistics callbacks will use the global software stats variable to report
whatever stats they need.
Actually ndo_get_stats64 doesn't need to fold the whole software stats
(mlx5e_grp_sw_update_stats), all it needs is five counters to fill the
rtnl_link_stats64 relevant stats parameter.
Hence this patch introduces a simpler helper function to fold software
stats for ndo_get_stats64 which will work directly on rtnl_link_stats64
stats parameter and not on the global or even temporary mlx5e_sw_stats
variable.
Since now mlx5e_grp_sw_update_stats is not called by ndo_get_stats64 we
can make it static and remove the temp var.
Unlike mlx5e_grp_sw_update_stats the new fold stats function doesn't
need to zero out the output statistics parameter since it is already
done by the stack @dev_get_stats().
This patch is fixing stack usage of mlx5e_grp_sw_update_stats on
x86 gcc-4.9 and higher, the concurrency issue between mlx5's
ndo_get_stats64 and get_ethtool_stats is resolved as well.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We were not tracking flow tables so far, add it up.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This confusing construction confuses the compiler which can't see
that flow is initialized if !err:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function `mlx5e_configure_flower`
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:2727:28: warning:
`flow` may be used uninitialized in this function
[-Wmaybe-uninitialized]
There is no reason for two function outputs, just return the
pointer directly and use ERR_PTR to encode a failure.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we have one cpu in XPS cpumask per tx queue, this is good
enough for default configuration where there is a tx queue per cpu.
However, once configuration changes to use less tx queues, part of the
cpus are not XPS-mapped and so the select queue decision falls back to
hash calculation and balancing is not guaranteed.
Expand XPS cpumask to enable using all cpus even when number of tx
queues is smaller than number of cpus.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Only the Receive CQ makes use of these fields. Take them
out into a separate struct and save space in the generic
CQ structure.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the non-linear SKB memory scheme of Striding RQ, a packet header
could cross page boundary. This requires special care in fast path
that costs LoC, additional runtime instructions and branches.
It could happen when the header (up to 256B) does not fit in
a single stride. Avoid this by working with a stride size that fits
the maximum possible header. Stride is increased form 64B to 256B.
Performance:
Tested packet rate for UDP streams, single ring, on ConnectX-5.
Configuration:
Set Striding RQ and LRO ON (to enabled the non-linear SKB scheme).
GRO OFF, early drop by TC rule.
64B: 4x worse memory utilization, no page-crossers headers
- No degradation (5,887,305 pps).
- The reduction in memory utilization is compensated by the saving of
branches tests.
192B: 1.33x worse memory utilization, avoid page-crossers headers
- Before: 5,727,252. After: 5,777,037. ~1% gain.
256B: Same memory util, no page-crossers
- Before: 5,691,885. After: 5,748,007. ~1% gain.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It turns out that libvirt uses 0-vid as a default if no vlan was
set for the guest (which is the case for switchdev mode) and errs
if we disallow that:
error: Failed to start domain vm75
error: Cannot set interface MAC/vlanid to 6a:66:2d:48:92:c2/0 \
for ifname enp59s0f0 vf 0: Operation not supported
So allow this in order not to break existing systems.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With VF LAG commit 491c37e49b "net/mlx5e: In case of LAG, one switch
parent id is used for all representors", both uplinks and all the VFs
(on both of them) get the same switchdev id.
This cause the provisioning system method to identify the rep of a given
VF from the parent PF PCI device using switchev id and physical port
name to break, since VFm of PF0 will have the (id, name) as VFm of PF1.
To fix that, we align to use the framework agreed upstream and set by
nfp commit 168c478e10 "nfp: wire get_phys_port_name on representors":
$ cat /sys/class/net/eth4_*/phys_port_name
p0
pf0vf0
pf0vf1
Now, the names will be different, e.g. pf0vf0 vs. pf1vf0.
Fixes: 491c37e49b ("net/mlx5e: In case of LAG, one switch parent id is used for all representors")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Waleed Musa <waleedm@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Prior to this patch the driver prohibited spoof checking on invalid MAC.
Now the user can set this configuration if it wishes to.
This is required since libvirt might invalidate the VF Mac by setting it
to zero, while spoofcheck is ON.
Fixes: 1ab2068a4c ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The lock in qp_table might be taken from process context or from
interrupt context. This may lead to a deadlock unless it is taken with
IRQs disabled.
Discovered by lockdep
================================
WARNING: inconsistent lock state
4.20.0-rc6
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W}
python/12572 [HC1[1]:SC0[0]:HE0:SE1] takes:
00000000052a4df4 (&(&table->lock)->rlock#2){?.+.}, /0x50 [mlx5_core]
{HARDIRQ-ON-W} state was registered at:
_raw_spin_lock+0x33/0x70
mlx5_get_rsc+0x1a/0x50 [mlx5_core]
mlx5_ib_eqe_pf_action+0x493/0x1be0 [mlx5_ib]
process_one_work+0x90c/0x1820
worker_thread+0x87/0xbb0
kthread+0x320/0x3e0
ret_from_fork+0x24/0x30
irq event stamp: 103928
hardirqs last enabled at (103927): [] nk+0x1a/0x1c
hardirqs last disabled at (103928): [] unk+0x1a/0x1c
softirqs last enabled at (103924): [] tcp_sendmsg+0x31/0x40
softirqs last disabled at (103922): [] 80
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&table->lock)->rlock#2);
lock(&(&table->lock)->rlock#2);
*** DEADLOCK ***
Fixes: 032080ab43 ("IB/mlx5: Lock QP during page fault handling")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5E_PFLAG_* definitions were changed from bitmask to enumerated
values. However, in mlx5e_open_rq(), the proper API (MLX5E_GET_PFLAG macro)
was not used to read the flag value of MLX5E_PFLAG_RX_NO_CSUM_COMPLETE.
Fixed it.
Fixes: 8ff57c18e9 ("net/mlx5e: Improve ethtool private-flags code structure")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit 5f5991f36d.
With the original commit, eswitch instance will not be initialized for
a function which is vport group manager but not eswitch manager such as
host PF on SmartNIC (BlueField) card. This will result in a kernel crash
when such a vport group manager is trying to access vports in its group.
E.g, PF vport manager (not eswitch manager) tries to configure the MAC
of its VF vport, a kernel trace will happen similar as bellow:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
...
RIP: 0010:mlx5_eswitch_get_vport_config+0xc/0x180 [mlx5_core]
...
Fixes: 5f5991f36d ("net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The IBM virtual ethernet driver's polling function continues
to process frames after rescheduling NAPI, resulting in a warning
if it exhausted its budget. Do not restart polling after calling
napi_reschedule. Instead let frames be processed in the following
instance.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few chip versions use the same sequence to adjust 10M and ALDPS, so
let's factor it out. This patch also fixes a (most likely) typo in
rtl8168g_1_hw_phy_config. There bit 8 in reg 0x14 on page 0x0bcc
was set and not cleared. According to the vendor driver this bit
needs to be cleared in all cases.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip versions from RTL8168g onward use the same sequence to disable
ALDPS (Advanced Link-Down Power Saving). So let's factor this out.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_clk_get() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Fixes: a7c30e62d4 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two statements are incorrecly indented, fix these by removing a space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A ternary match table is used for RFS. If multiple entries in the table
match, the entry with the lowest numerical values index is chosen as the
matching entry. Entries in the table are identified using an index
which takes a value from 0 to PRFSCAPR[NUM_RFS]-1 when accessed by the
PSI (PF).
Portions of the RFS table can be assigned to each SI by the PSI (PF)
driver in PSIaRFSCFGR. Assignments are cumulative, the entries assigned
to SIn start after those assigned to SIn-1. The total assignments to
all SIs must be equal to or less than the number available to the port
as found in PRFSCAPR.
For RSS, the Toeplitz hash function used requires two inputs, a 40B
random secret key that is supplied through the PRSSKR0-9 registers as well
as the relevant pieces of the packet header (n-tuple). The 6 LSB bits of
the hash function result will then be used as a pointer to obtain the tag
referenced in the 64 entry indirection table. The result will provide a
winning group which will be used to help route the received packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSIs (VFs) may send a message to the PSI (PF) for general notification
or to gain access to hardware resources which requires host inspection.
These messages may vary in size and are handled as a partition copy
between two memory regions owned by the respective participants.
The PSI will respond with fail or success and a 16-bit message code.
The patch implements the vf to pf messaging mechanism above and, as the
first application making use of this support, it enables the VF to
configure its own primary MAC address.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds most h/w statistics counters: non-privileged SI conters, as
well as privileged Port and MAC counters available only to the PF.
Per ring software stats are also included.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC is a multi-port virtualized Ethernet controller supporting GbE
designs and Time-Sensitive Networking (TSN) functionality.
ENETC is operating as an SR-IOV multi-PF capable Root Complex Integrated
Endpoint (RCIE). As such, it contains multiple physical (PF) and
virtual (VF) PCIe functions, discoverable by standard PCI Express.
Introduce basic PF and VF ENETC ethernet drivers. The PF has access to
the ENETC Port registers and resources and makes the required privileged
configurations for the underlying VF devices. Common functionality is
controlled through so called System Interface (SI) register blocks, PFs
and VFs own a SI each. Though SI register blocks are almost identical,
there are a few privileged SI level controls that are accessible only to
PFs, and so the distinction is made between PF SIs (PSI) and VF SIs (VSI).
As such, the bulk of the code, including datapath processing, basic h/w
offload support and generic pci related configuration, is shared between
the 2 drivers and is factored out in common source files (i.e. enetc.c).
Major functionalities included (for both drivers):
MSI-X support for Rx and Tx processing, assignment of Rx/Tx BD ring pairs
to MSI-X entries, multi-queue support, Rx S/G (Rx frame fragmentation) and
jumbo frame (up to 9600B) support, Rx paged allocation and reuse, Tx S/G
support (NETIF_F_SG), Rx and Tx checksum offload, PF MAC filtering and
initial control ring support, VLAN extraction/ insertion, PF Rx VLAN
CTAG filtering, VF mac address config support, VF VLAN isolation support,
etc.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soften the memory barrier call of mb() by a sufficient wmb() in the
consumer index update of the event queues.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Procedure mlx4_init_user_cqes() handles returns by copy_to_user
incorrectly. copy_to_user() returns the number of bytes not copied.
Thus, a non-zero return should be treated as a -EFAULT error
(as is done elsewhere in the kernel). However, mlx4_init_user_cqes()
error handling simply returns the number of bytes not copied
(instead of -EFAULT).
Note, though, that this is a harmless bug: procedure mlx4_alloc_cq()
(which is the only caller of mlx4_init_user_cqes()) treats any
non-zero return as an error, but that returned error value is processed
internally, and not passed further up the call stack.
In addition, fixes the following sparse warning:
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:1>*to
got void *buf
Fixes: e45678973d ("{net, IB}/mlx4: Initialize CQ buffers in the driver when possible")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned. In addition some reserved bits were wrongly read. Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.
Fixes: ab9c17a009 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654b ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling pci_enable_atomic_ops_to_root enables AtomicOp requests to pci
root port.
AtomicOp requests will be enabled only if the completer and all
intermediate pci bridges support PCI atomic operations.
This, together with appropriate settings in the NVCONFIG should enable
PCI atomic operations on the device.
PCI atomic operations were first introduced in PCI Express Base Specification
2.1. The Supported operations are Swap (Unconditional Swap), CAS (Compare and
Swap) and FetchAdd (Fetch and Add).
Unlike other atomic operation modes PCI atomic operations gives the user
the option to do atomic operations on local memory, without involving verbs
api, without it compromising the operation's atomicity.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
APIs that have deferred callbacks should have some kind of cleanup
function that callers can use to fence the callbacks. Otherwise things
like module unloading can lead to dangling function pointers, or worse.
The IB MR code is the only place that calls this function and had a
really poor attempt at creating this fence. Provide a good version in
the core code as future patches will add more places that need this
fence.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Add a verifier callback to the nfp JIT to remove the instructions
the verifier deemed to be dead.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Verifier will now optimize out branches to dead code, implement
the replace_insn callback to take advantage of that optimization.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instead of passing env->prog->len around, and trying to adjust
for optimized out instructions just save the initial number
of instructions in struct nfp_prog.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We fail program loading if jump lands on a skipped instruction.
This is for historical reasons, it used to be that we only skipped
instructions optimized out based on prior context, and therefore
the optimization would be buggy if we jumped directly to such
instruction (because the context would be skipped by the jump).
There are cases where instructions can be skipped without any
context, for example there is no point in generating code for:
r0 |= 0
We will also soon support dropping dead code, so make the skip
logic differentiate between "optimized with preceding context"
vs other skip types.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instruction number is meaningless at code gen phase. The target
of the instruction is overwritten by nfp_fixup_branches(). The
convention is to put the raw offset in target address as a place
holder. See cmp_* functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
So far member rtl_fw has three states:
- IS_ERR(rtl_fw): firmware not loaded
- !rtl_fw: no firmware available
- other: firmware loaded
This can be made simpler and clearer by adding the firmware name as
member fw_name to struct rtl8169_private. Then:
- !fw_name: no firmware available
- !rtl_fw: firmware not loaded
- rtl_fw: firmware loaded
This change also allows to easily merge rtl_request_uncached_firmware
into rtl_request_firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a bitmap to keep track of which partition types we've already seen;
for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
sfc NICs. Prior to this patch they cause sysfs_warn_dup errors because
they have the same name, causing us not to expose any MTDs at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFC enabling is based on user priority, currently it is
based on TC, which may cause PFC not setting correctly when pri
to TC mapping is not one to one relation.
This patch adds pfc_en in tm_info to fix it.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old firmware version, statistics acquisition of
PFC frames and MAC control frames is not supported.
Add command retrieves statistics for PFC frames and
MAC control frames from the firmware.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the TC weight in SSU module according to
info in tm_info.
Also, zero weight of TC weight in SSU ETS module means enabling
strict priority, so do not allow zero weight when in ETS mode.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GE MAC does not support PFC, when driver is initializing and MAC
is in GE Mode, ignore the fw not supported error, otherwise
initialization will fail.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to firmware error code definition, the error code of 2
means NOT_SUPPORTED, this patch changes it to NOT_SUPPORTED.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Param pending_buf and skb may be not NULL when free ring.
This patch clears them when free ring.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.
This patch fixes it.
Fixes: 849e460776 ("net: hns3: add ethtool_ops.get_channels support for VF")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shaper setting does not change currently, when TC num changes,
which may cause shaper parameter not setting problem.
This patch fixes it by setting the shaper parameter when TC num
changes.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rss configuration set by user will be lost when setting
channel.
This patch fixes it by not setting rss configuration to default
if user has configured the rss.
Fixes: 09f2af6405 ("net: hns3: add support to modify tqps number")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In origin codes, there are some statistics item are got from mac, which
also include the packets statistics of VF. It is unreasonable. This
patch fixes it by counting them in the rx/tx processing flow.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx multicast packets statistic for each ring.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds calling roce callback function when link status
change.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable VXLAN on Spectrum-2 as previous patches added the required
functionality.
Note that for now Spectrum-1 and Spectrum-2 use the same function to
determine whether the VXLAN configuration is valid or not. In the
future, when the driver will be extended to support features not present
in Spectrum-1, two different functions will be needed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-1 and Spectrum-2 are largely backward compatible with regards
to VXLAN. One difference - as explained in previous patch - is that an
underlay RIF needs to be specified instead of an underlay VR during NVE
initialization. This is accomplished by calling the relevant function
that returns the index of such a RIF based on the table ID
(RT_TABLE_MAIN) where underlay look up occurs.
The second difference is that VXLAN learning (snooping) is controlled
via a different register (TNPC).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of a VXLAN tunnel in Spectrum-1 and Spectrum-2 is
largely the same. To avoid code duplication, breakout the common parts
to a common function that can be invoked from the ASIC-specific code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, instead of providing the ID of the virtual router (VR)
where NVE underlay lookups will occur as in Spectrum-1, the ID of a
router interface (RIF) in this VR is required.
Expose functions to create and destroy such a RIF.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB may provide a checksum of packet data appended to packet data. In
order to allow this checksum to be received by the host descriptor data
needs to be enlarged by 2 bytes to accommodate the checksum.
In the case of MTU-sized packets without a VLAN tag the
checksum were already accommodated by virtue of the space reserved for the
VLAN tag. However, a packet of MTU-size with a VLAN tag consumed all
packet data space provided by a descriptor leaving no space for the
trailing checksum.
This was not detected by the driver which incorrectly used the last two
bytes of packet data as the checksum and truncate the packet by two bytes.
This resulted all such packets being dropped.
A work around is to disable RX checksum offload
# ethtool -K eth0 rx off
This patch resolves this problem by increasing the size available for
packet data in RX descriptors by two bytes.
Tested on R-Car E3 (r8a77990) ES1.0 based Ebisu-4D board
v2
* Use sizeof(__sum16) directly rather than adding a driver-local
#define for the size of the checksum provided by the hw (2 bytes).
Fixes: 4d86d38186 ("ravb: RX checksum offload")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/mellanox/mlx4/eq.c: In function ‘mlx4_eq_int’:
drivers/net/ethernet/mellanox/mlx4/mlx4.h:219:5: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (mlx4_debug_level) \
^
drivers/net/ethernet/mellanox/mlx4/eq.c:558:4: note: in expansion of macro ‘mlx4_dbg’
mlx4_dbg(dev, "%s: MLX4_EVENT_TYPE_SRQ_LIMIT. srq_no=0x%x, eq 0x%x\n",
^~~~~~~~
drivers/net/ethernet/mellanox/mlx4/eq.c:561:3: note: here
case MLX4_EVENT_TYPE_SRQ_CATAS_ERROR:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:2126:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:790:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/ethernet/brocade/bna/bfa_ioc.c:860:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c:6336:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2231:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/ethernet/broadcom/tg3.c:722:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/ethernet/broadcom/tg3.c:783:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/ethernet/3com/3c509.c:1265:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/ethernet/3com/3c509.c:1271:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, there were bunch of fixes to bnx2x driver, the code is now
aligned to out-of-box driver version 1.713.36. This patch updates
bnx2x driver version to 1.713.36.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the device tree binding the phy-supply property is
optional. Use the regulator_get_optional API accordingly. The
code already handles NULL just fine.
This gets rid of the following warning:
fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Speed should be supported by Physical Port Capabilities.
2) report Forward Error Correction mode which are available.
3) Added few comments.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add glue driver to support Qualcomm ETHQOS using stmmac driver.
This is based on downstream driver written by Siddarth Gupta, Sunil
Kumar Paidimarri, Rahul Ankushrao Kawadgave, Nisha Menon, Jagadeesh
Babu Challagundla, Chaitanya Pratapa, Lakshit Tyagi, Suraj Jaiswal,
Sneh Shah and Ventrapragada Ravi Kanth
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The connect_local_phy should return NULL (not negative errno) on
error, since its caller expects it.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converted to use "imply" instead of "select" for PTP_1588_CLOCK
driver selecting. This could break the hard dependency between
the PTP clock subsystem and ethernet drivers.
This patch also set "default y" for dpaa2 ptp driver building to
provide user an available ptp clock in default.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively.
Signed-off-by: Artem Panfilov <panfilov.artyom@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device IDs to support following cards:
1. Add device id 0x0205 for HINIC 100GE dual port mezz card.
2. Add device id 0x0210 for HINIC 25GE quad port mezz card.
3. Delete device id 0x0201 for HINIC 100GE dual port card, because
this is used by other product.
4. Macro of device id 0x200 is modified for HINIC 100GE dual port card.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old non-PCIe chip versions support PCI DAC, however this feature
seems to be fragile, see comment in the PCI error handler. Therefore
it's disabled per default. I think meanwhile it's time remove support
for this legacy feature. This helps to reduce complexity of the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8 years ago, as part of 6f0333b8fd ("r8169: use 50% less ram for RX
ring"), the alignment requirement for rx buffers was silently changed
from 8 bytes to 16 bytes. I found nothing explaining this, also the
chip specs I have only mention an 8 byte requirement.
AFAICS kmalloc_node() guarantees allocated memory to be at least
"long long" aligned, what is 8 bytes on a 32 bit machine.
So we can take this memory as-is and avoid some overhead by changing
the alignment requirement back to 8 bytes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-01-22
This series contains updates to i40e and xsk.
Jan exports xdp_get_umem_from_qid() for other drivers/modules to use.
Refactored the code use the netdev provided umems, instead of containing
them inside our i40e_vsi.
Aleksandr fixes an issue where RSS queues were misconfigured, so limit
the RSS queue number to the online CPU number.
Damian adds support for ethtool's setting and getting the FEC
configuration.
Grzegorz fixes a type mismatch, where the return value was not matching
the function declaration.
Sergey adds checks in the queue configuration handler to ensure the
number of queue pairs requested by the VF is less than maximum possible.
Lihong cleans up code left around from earlier silicon validation in the
i40e debugfs code.
Julia Lawall and Colin Ian King clean up white space indentation issues
found.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent addition of SPDX license identifiers to the files in
drivers/net/ethernet/sun created a licensing conflict.
The cassini driver files contain a proper license notice:
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
but the SPDX change added:
SPDX-License-Identifier: GPL-2.0
So the file got tagged GPL v2 only while in fact it is licensed under GPL
v2 or later.
It's nice that people care about the SPDX tags, but they need to be more
careful about it. Not everything under (the) sun belongs to ...
Fix up the SPDX identifier and remove the boiler plate text as it is
redundant.
Fixes: c861ef83d7 ("sun: Add SPDX license tags to Sun network drivers")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several statements that have incorrect levels of indentation,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert spaces to tabs to get correct alignment.
Found with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The tx_timeout command from debugfs was originally intended to support
early silicon validation efforts. It is no longer needed. Thus remove it to
avoid misuse of triggering tx_timeout through debugfs.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check if num_queue_pairs number requested by VF is less than
maximum possible value in VIRTCHNL_OP_CONFIG_VSI_QUEUES handler.
Also check if local_vf_id >= 0 in common handler since it is of
int type and can potentially be negative.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change of function declaration from int to u64 due to
return type mismatch (u64).
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for setting/getting FEC configuration
using ethtool options:
set/show-priv-flags rs-fec/base-r-fec
set/show-fec off/rs/baser/auto for kernels version >= 4.14
Signed-off-by: Damian Dybek <damian.dybek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Limiting RSS queues number to online CPUs number in order to
avoid issues with creating misconfigured RSS queues.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As current implementation of netdev already contains and provides
umems for us, we no longer have the need to contain these
structures in i40e_vsi.
Refactor the code to operate on netdev-provided umems.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Spectrum-2 GRE tunnel implementation requires a specific underlay RIF that
points to the virtual router used for forwarding the encapsulated packet.
Add Spectrum-2 specific loopback router interface creation methods which
may create or reuse the dedicated underlay RIF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 requires to specify the egress RIF when setting tunnel decap
properties. Add a method for accessing the underlay RIF index and then use
it when setting decap properties.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 underlay RIF is merely an auxiliary RIF that points to the
virtual router used for encapsulated packets lookup. It exists only when
its overlay RIF exists but may be shared with other overlay RIFs.
Hence it is undesired to mark any device as related to it.
Therefore allow usage of NULL device when allocating RIF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of Spectrum-2 GRE support, as ul_vr_id field is reserved for
Spectrum-2, Change mlxsw_sp_ipip_lb_ul_vr_id() implementation not to use
the reserved field.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 GRE tunnels underlay should be given not only the virtual router
information for an encapsulated packet lookup, but also an underlay RIF
object which belongs to a virtual router.
Therefore add ul_rif_id field in struct mlxsw_sp_rif_ipip_lb, to be used
later in Spectrum-2 underlay RIF implementation. This field complements
ul_vr_id field, already present and defined as reserved for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The presence of an allocated RIF in mlxsw_sp->router->rifs[rif_index] marks
that rif_index as taken.
Set the marking of a taken RIF to happen before calling ops->create in
order to allow creation of a GRE underlay RIF, which may be allocated and
created as part of an overlay RIF creation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, the underlay routing table is pointed by an underlay router
interface in contrary to Spectrum where only an underlay virtual router
should be set. That makes the underlay virtual router field in RITR
reserved for Spectrum-2.
Change loopback RIF creation function to support the new underlay RIF
field, however leave this field reserved for Spectrum-1 updates.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RIF ops array as member of mlxsw_sp in order to control which RIF
operations callbacks are called per ASIC type. This is needed to control
per ASIC handling of loopback RIF configurations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split RIF ops array for Spectrum-1 and Spectrum-2 callbacks in order to
support different sets of operations for loopback RIF handling, as
underlying implementation differs between the ASICs.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2 we need to specify the underlay egress router interface
when performing IP-in-IP and NVE packet decapsulation in the underlay
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fields relevant for Spectrum-2 Loopback IPinIP router interface
creation. Add additional Loopback RIF protocol value - Generic, used for
creation of an explicit underlay RIF, and also add a field named
underlay_rif used for specifying the underlay RIF of a tunnel.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_init_one() is complex enough, so we better factor out getting the
ether_clk.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing the phy_device indirectly via the netdevice causes few issues:
- Accessing the phy_device when it's not attached may cause a NPE.
- If we have to access the phy_device when it's not attached we have
to use mdiobus_get_phy() to get a reference to the phy_device.
Therefore store a phy_device reference in struct rtl8169_private directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Triggering an asynchronous reset is problematic for the following
reasons, therefore reset the chip synchronously.
- The reset routine resets registers and parameters behind our back
what may collide with code executed after triggering the reset.
- __rtl8169_resume() is called as part of pm_runtime_get_sync() and
callers expect that the chip is fully resumed afterwards.
In context of this driver triggering an asynchonous reset should be
considered an emergency procedure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for locking / unlocking the config registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All calls to this function have the enable parameter set to false.
So we can replace the function with a disable-only version.
v2:
- fixed copy & paste error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's sufficient to initialize the workqueue once, therefore remove the
additional initialization whenever rtl_open() is called.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_hw_reset() is called as part of the reset routine which is
scheduled in the line after. So we can remove the call to
rtl8169_hw_reset() here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper is used only once, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export detailed driver counters through debugfs.
Statistics already available in ethtool are presented in a
structured manner. Includes per-core, per-FQ and per-channel statistics.
Also transition from module_fsl_mc_driver to explicit module_init/exit
in order to create the debugfs directory besides registering the driver.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform dpaa2_eth_queue_count into a macro to follow the
the convention used by dpaa2_eth_fs_count and other functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcQmwjAAoJEEg/ir3gV/o+aBEIAIE8q3gEonMEPLnRoYSBlgUy
ZBl7/51yzC8CVdsdO7hx5dyyiI+gYq10Jp6TVpqA2i/V8P871T/u6+xRhP3T7dOc
Fq2YE70NdkCqFkpyc0QONzMC7ypwVqIEJrX7KnuLi5Ybsm9+tDia8AgC0NX/0H3U
bRgfzpupfK0TiLgtBe7kqC2WTo+bPzu0cEUu7xjQqUgZZie5QPyzW/6cEtn/V75+
A3btMNS5w0cfYK4mR4MMuc+UT4rSbsdyIZQrzICo75C2UnVMlojDf90+RuW4JFVw
tuOMA1LCB5l3lphgEEEerV2dZvs0ZJEuoYoFUkfgu2QEFSOMhod71t8/rurih0s=
=f23b
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-01-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-01-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')
The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.
Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.
Fixes: f5bc2c5de1 ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
