The i211's one-time programmable (invm) version field is different than the
other fields contained in it. This patch adds a function to get the invm version
of it and store it for output from ethtool.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes a workaround that was needed on pre-release hardware.
Released hardware should not have this setting, but any devices that do
will get a warning message instead.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The q_vector->itr check in ixgbe_configure_tx_ring() was done prior to it
being set, which resulted in TXDCTL.WTHRESH always being set to 1 on driver
load, while consequent resets would set it to 8.
This patch moves the setting of q_vector->itr in ixgbe_alloc_q_vector() to
make sure that TXDCTL.WTHRESH is set to 8 by default.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug in ixgbe_ptp_check_pps_event where the type was
uninitialized and could cause unknown event outcomes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe, ixgbevf, igbvf, igb and
networking core (bridge). Most notably is the addition of support
for local link multicast addresses in SR-IOV mode to the networking
core.
Also note, the ixgbe patch "ixgbe: Add support for pipeline reset" and
"ixgbe: Fix return value from macvlan filter function" is revised based
on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following build failure on S390:
In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware doesn't support controlling pause frames autoneg, so
report that back correctly to userspace.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable retval is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the net device ops to manage the embedded
hardware bridge on ixgbe devices. With this patch the bridge
mode can be toggled between VEB and VEPA to support stacking
macvlan devices or using the embedded switch without any SW
component in 802.1Qbg/br environments.
Additionally, this adds source address pruning to the ixgbevf
driver to prune any frames sent back from a reflective relay on
the switch. This is required because the existing hardware does
not support this. Without it frames get pushed into the stack
with its own src mac which is invalid per 802.1Qbg VEPA
definition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes a sparse warning triggered by us casting the timestamp in
the packet as a u64 instead of as a __le64. This change corrects that in
order to resolve the sparse warning.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are multiple places in our device nvm where the version is stored.
This update fixes some output errors with some types of images and
refactors the way the version data is gathered and stored for ethtool output.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newer devices supported by igb can support auto-crossover detection in
forced operation modes. Enable this in the driver, rather than clobbering
this functionality in forced operation.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability. Check the return value
and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should not forward LLDP type frames. Inspect the ether type and
do not send if it is an LLDP ethertype frame.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hw timestamping code caused performance regression in ixgbe driver when the
timestamping is not enabled. The culprit is IXGBE_READ_REG call in the Rx
path which is executed for every received skb. This call is not needed when
the timestamping is disabled or for non-ptp packets.
netperf results:
The ixgbe side of the connection was acting as a server, the netperf command
line on the other side was:
netperf -H 192.168.1.23 -T0,0 -t UDP_STREAM -l 20
The values below mean throughput as reported by netperf (local/remote), for
3 runs, with timestamping not enabled.
3.7.0-rc1+ with CONFIG_IXGBE_PTP off:
5373.83 / 3329.32
5721.88 / 3033.89
5653.42 / 3112.38
3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5233.64 / 1226.85
5448.67 / 1039.32
5421.36 / 1095.66
Patched 3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5594.72 / 2942.53
5428.95 / 3110.16
5343.56 / 3200.48
Reported-by: Jesper Brouer <jbrouer@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds/updates ASCII descriptor maps for 82598 and 82599 Tx/Rx descriptors.
Current descriptor maps were out of date for 82598 and incorrect for
82599.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that compare the total_rx_packets cleaned to budget
instead of decrementing budget. The advantage to this approach is that budget
can now be const and we only end up modifying total_rx_packets instead of
modifying both it and budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting a MAC filter for the VF the function should return a success
or failure code, not the index of the new filter. It causes spurious NACK
returns to the VF driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the check for calling en/disable_tx_laser() function
pointer. The pointer is only set on parts that can use it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SR-IOV mode the PF driver acts as the uplink port and is
used to send control packets e.g. lldpad, stp, etc.
eth0.1 eth0.2 eth0
VF VF PF
| | | <-- stand-in for uplink
| | |
--------------------------
| Embedded Switch |
--------------------------
|
MAC <-- uplink
But the embedded switch is setup to forward multicast addresses
to all interfaces both VFs and PF and onto the physical link.
This results in reserved MAC addresses used by control protocols
to be forwarded over the switch onto the VF.
In the LLDP case the PF sends an LLDPDU and it is currently
being forwarded to all the VFs who then see the PF as a peer.
This is incorrect.
This patch adds the multicast addresses to the RAR table in the
hardware to prevent this behavior.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function to set the macvlan filter should return success or failure
instead of the index of the filter. The message processing function was
misinterpreting the index as a non-zero return code indicating failure and
NACKing MAC filter set messages that actually succeeded.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline
reset on all 82599 devices. This is necessary to avoid possible link issues.
Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap
all AUTOC writes when LESM is enabled.
v2- fix LMS behaviour based on feedback by Martin Josefsson
CC: Martin Josefsson <gandalf@mjufs.se>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1EJ/
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance. Also adopt use of skb_frag_size() accessor.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org [v3.6]
Signed-off-by: David S. Miller <davem@davemloft.net>
If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Uri Habusha <urih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ALDPS function to save power when link down. Note that the
feature should be set after the other PHY settings. And the firmware
is necessary. Don't enable it without loading the firmware.
None of the firmware-free chipsets support ALDPS. Neither do the
RTL8168d/8111d.
For 8136 series, make sure the ALDPS is disabled before loading the
firmware. For 8168 series, the ALDPS would be disabled automatically
when loading firmware. You must not disable it directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a 36 bit dtb file, the driver complains "resource busy".
Investigating the source of the message leads one to the
gianfar_ptp_probe function.
Since the type of the device resource requested in this function
is IORESOURCE_MEM, it should use "iomem_resource" instead of
"ioports_resource".
Signed-off-by: Wei Yang <Wei.Yang@windriver.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw/davinci mdio ip cores are present on am33xx, so make NET_VENDOR_TI
visible for it as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to allocate rx buffers pool by any reason, we'll just return
with an error, however we've previously successfully requested an irq. Fix
this by releasing the irq before returning the error.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flashing code, even though it works correctly, makes some hidden
assumptions about buffer sizes. This is causing code analysers to
report error. Cleanup FW flashing code to remove these hidden assumptions.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the resource cleanup to act correctly and prevent a kernel oops when
mlx4_QUERY_ADAPTER() fails.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These debug prints left behind by commits c82e9aa0a8 ("mlx4_core:
resource tracking for HCA resources used by guests"), 54679e1482
("mlx4: Implement QP paravirtualization and maintain phys_pkey_cache
for smp_snoop") and 993c401e20 ("mlx4_core: Add IB port-state
machine and port mgmt event propagation") make it pretty hard to
actually use the mlx4_core debug messages when running in SRIOV/IB
mode -- for example, the module load sequence of a device with one VF
yielded 631 debug prints, with 408 of them being from this set. Let's
just remove them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability. Check the return value
and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the igb driver version to 4.0.17.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a problem in the initial implementation of the get cable length
function for i210 and it did not work properly. This patch fixes that
problem for i210/i211 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a HW requirement. Although a buffer as short as 1 byte is allowed,
the total length of packet before, padding and CRC insertion, must be at
least 17 bytes. So pad all small packets manually up to 17 bytes before
delivering them to HW.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe only. Only change to this series
is I dropped the "ixgbe: Add support for pipeline reset" due to
change requested by Martin Josefsson.
Alexander Duyck (7):
ixgbe: Add support for IPv6 and UDP to ixgbe_get_headlen
ixgbe: Add support for tracking the default user priority to SR-IOV
ixgbe: Add support for GET_QUEUES message to get DCB configuration
ixgbe: Enable support for VF API version 1.1 in the PF.
ixgbevf: Add VF DCB + SR-IOV support
ixgbe: Drop unnecessary addition from ixgbe_set_rx_buffer_len
ixgbe: Fix possible memory leak in ixgbe_set_ringparam
Don Skidmore (1):
ixgbe: Add function ixgbe_reset_pipeline_82599
Emil Tantilov (1):
ixgbe: add WOL support for new subdevice id
Jacob Keller (1):
ixgbe: (PTP) refactor init, cyclecounter and reset
Tushar Dave (1):
ixgbe: Correcting small packet padding
Wei Yongjun (1):
ixgbe: using is_zero_ether_addr() to simplify the code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building macb on x86_64 the following warnings show up:
drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC_RX-related bits into separate functions.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not correctly freeing the temporary rings on error in
ixgbe_set_ring_param. In order to correct this I am unwinding a number of
changes that were made in order to get things back to the original working
form with modification for the current ring layouts.
This approach has multiple advantages including a smaller memory footprint,
and the fact that the interface is stopped while we are allocating the rings
meaning that there is less potential for some sort of memory corruption on the
ring.
The only disadvantage I see with this approach is that on a Rx allocation
failure we will report an error and only update the Tx rings. However the
adapter should be fully functional in this state and the likelihood of such
an error is very low. In addition it is not unreasonable to expect the
user to need to recheck the ring configuration should they experience an
error setting the ring sizes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function that forces a full pipeline reset. This
function will be used in following patches to completely reset the PHY
during resets.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We still had some code floating around from the old single buffer receive
path. As a result we were adding VLAN_HLEN to max_frame although the
resultant value was never used. Since that is the case we can drop this from
the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver pad skb up to 17 bytes because of the HW requirement. However, that code
implementation mess up the skb tail pointer after padding. This patch sets
skb->tail correctly.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using is_zero_ether_addr() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies when and where PTP registers and data are set. Previously
a work-around was used inside cyclecounter_start in order to reset some of the
time registers. This patch creates a new ixgbe_ptp_reset specifically for this
purpose. The cyclecounter configuration has trimmed down to only modify what
is necessary. Due to hardware conditions after probe and before open, PTP init
has now moved into the ixgbe_open call. This allows the ptp device name in the
sysfs to be the ethernet device name instead of the MAC address.
The cyclecounter check flag is renamed to PTP_ENABLED and is used to prevent
PTP init from happening when PTP has not been enabled.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a subdevice id for new 82599 device. The define is needed
to allow enabling WOL support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for DCB and SR-IOV from the VF. With this change
in place the VF will correctly use a traffic class other than 0 in the case
that the PF is configured with the default user priority belonging to a
traffic class other than 0.
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change switches on the last few bits for us enabling version 1.1 VF
support in the PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues in regards to the combination of DCB
and SR-IOV. Specifically it allows us to send information to the VF on
which queues it should be using.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is necessary to track the default user priority in the PF so that we can
force it upon the VFs. The motivation behind this is to keep the VFs from
getting access to user priorities meant for things like storage.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for IPv6 and UDP to ixgbe_get_headlen. The
advantage to this is that we can now handle ipv4/UDP, ipv6/TCP, and
ipv6/UDP with a single memcpy instead of having to do them in multiple
pskb_may_pull calls.
A quick bit of testing shows that we increase throughput for a single
session of netperf from 8800Mpbs to about 9300Mpbs in the case of ipv6/TCP.
As such overall ipv6 performance should improve with this change.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before use the request and response queue addr, make sure it has wrote
to the registers.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flash layout on Skyhawk-R is different from BE3-R.
Hence the code needs to be fixed to flash FW on Skyhawk-R.
Also cleaning up code in BE3-R flashing function.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_shutdown is enabling wake-on-lan by calling be_setup_wol.
Emulex adapter do not support wake-on-lan in S5 state.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver should enable VF so that VF goes to ready state in
new Lancer FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCI EEH, driver waits for all functions in the card.
Wait is needed only once per card. Fix is to wait only for the
first PCI function.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During recovery from a FW error, destroy queue operation may fail.
Queue should be marked as destroyed so that recovery code can recreate
the queue. Also fix queue created state not getting checked at one instance.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return default values for fields for which VFs dont have privilege to get the
required information from FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF does not have privileges to execute many commands. When VFs try
to execute those commands there are unnecessary error messages.
Fix this by executing only those commands for which VF has privilege.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow adding VLANs for Lancer VF.
VLAN ID 0 should not be added to list of VLANs sent to FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After FW error, driver should wait for NO_RESOURCE error to disappear before
proceeding with recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For changing MAC of VF from PF, delete MAC operation needs to be done before
assigning new MAC. Also in ndo_set_mac_address operation avoid delete MAC if
it has been already deleted by PF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use Lancer specific command to set QoS for VF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assumes FW resource counts and capabilities while creating queues and
using functionality like RSS. This causes driver load to fail in FW configs
where resources and capabilities are reduced. Fix this by querying FW
configuration during probe and using resources and capabilities accordingly.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also fixes the build failure caused due to removal of #ifdef
CONFIG_CHELSIO_T4_OFFLOAD condition
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe and igb.
Alexander Duyck (13):
ixgbe: Initialize q_vector cpu and affinity masks correctly
ixgbe: Enable jumbo frames support w/ SR-IOV
ixgbe: Move message handling routines into their own functions
ixgbe: Add mailbox API version negotiation support to ixgbe PF
igb: Split Rx timestamping into two separate functions
igb: Do not use header split, instead receive all frames into a
single buffer
igb: Combine post-processing of skb into a single function
igb: Map entire page and sync half instead of mapping and unmapping
half pages
igb: Move rx_buffer related code in Rx cleanup path into separate
function
igb: Lock buffer size at 2K even on systems with larger pages
igb: Combine q_vector and ring allocation into a single function
igb: Move the calls to set the Tx and Rx queues into igb_open
igb: Split igb_update_dca into separate Tx and Rx functions
Tushar Dave (1):
igb: Correcting and improving small packet check and padding
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things:
* Use macb struct members and remove at91_ether ones
* Alloc DMA buffers on netdev start and dealloc on stop
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This rips out the at91_ether phy handling and ethtool stuff
and replace it with equivalent stuff from macb.
The only thing lost is the phy irq support from at91_ether,
but this can be added to macb and then benefit all users.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This will make it easier to share code between the drivers and
eventually merge them into one driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Use register and bits definitions from the macb header. This makes it
possible to have one header file for this hardware.
Process was scripted and the resulting object file has the same checksum.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This change makes it so that igb_update_dca is broken into two halves, one
for Rx and one for Tx. The advantage to this is primarily readability.
In addition I am enabling relaxed ordering for reads from hardware since
this is supported on all of the igb parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change helps to address locking issues seen with
netif_set_real_num_tx_queues and netif_set_real_num_rx_queues when used in
the igb_set_interrupt_capability function. To resolve these locking issues
I have moved the two function calls into __igb_open so that they can be
called while the RTNL lock is held.
An added advantage to this is that the number of queues is not updated
until the last possible moment so if there are any issues in allocating
MSI-X interrupts or resources for the rings we have time to change the
values prior to updating the netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change combines the the allocation of q_vectors and rings into a single
function. The advantage of this is that we are guaranteed we will avoid
overlap in the L1 cache sets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change locks us in at 2K buffers even on a system that supports larger
frames. The reason for this change is to make better use of pages and to
reduce the overall truesize of frames generated by igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to try and isolate things a bit further I am moving the code
related to retrieving data from the rx_buffer_info structure into a
separate function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we map the entire page and just sync half of
it for the device at a time. The advantage to this approach is that we can
avoid the locking on map/unmap seen in many IOMMU implementations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to just clean-up a number of function calls that were
made at the end of the Rx clean-up path by combining them into a single
function call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we no longer use header split. The idea is to
reduce partial cache line writes by hardware when handling frames larger
then header size. We can compensate for the extra overhead of having to
memcpy the header buffer by avoiding the cache misses seen by leaving an
full skb allocated and sitting on the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support page based receive we will need to split up the two
different types of timestamping into two separate functions. The first one
will handle legacy timestamps with the value in the register, and the new
one will handle timestamps in the Rx buffer itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current implementation mess up the tail pointer. This patch sets skb->tail
correctly.
Also, the small packet check and padding is optimized by using unlikely and
calling skb_pad directly.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows us to add a mailbox versioning API. This will allow us
to determine the features supported by the VFs from the PF. For example we
will be implementing a version 1.1 API for the VF that will indicate that
it can support us enabling Jumbo frames as the VF will support buffer
chaining.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of trying to maintain one large monolithic function that handles
most of the different messages from the VF it makes sense to break the
message handling function up so that we can just go through one switch
statement and call the correct routine for a given message.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can have limited support for jumbo frames
when SR-IOV is enabled. In order to accomplish this it is necessary to
disable all VFs when the PF has jumbo frames enabled. If the VFs then
request the same maximum frame size as the PF they will be re-enabled. A
follow on patch will add a means of identifying when a VF can support
spanning buffers and does not need to be worried about the actual supported
max frame size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling DCB the rings belonging to a q_vector on CPU 0 were not
reinitializing their DCA registers. Upon closer inspection the issue was
that the q_vector CPU variable was left at 0 resulting in the driver not
updating the DCA registers.
In order to guarantee the DCA registers will be updated I am adding a
couple line change so that we initialize the CPU variable to -1 which will
force a DCA update the first time an interrupt fires on that q_vector.
In addition we were setting the CPU affinity hint to all CPUs when we were
not specifying a CPU. Instead we should leave it as all zeros to avoid any
possible confusion about the fact that we shouldn't be giving a hint.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a3348722 AFEX FCoE function is continuously reset.
The patch prevents the resetting and removes debug print
to stop garbaging syslog.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).
http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.
Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.
Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled. Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.
Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.
To avoid possible Tx stalls, change WTHRESH back to 1.
The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.
please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3bc1
Author: Tom Herbert <therbert@google.com>
Date: Mon Nov 28 16:33:16 2011 +0000
e1000e: Support for byte queue limits
Changes to e1000e to use byte queue limits.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain platforms, BE hardware could falsely indicate UE.
For BE family of NICs, do not set hw_error based on the UE bits.
If there was a real fatal error, the corresponding h/w block will
automatically go offline and stop traffic.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported a kernel build failure as following:
drivers/built-in.o: In function `pch_gbe_ioctl':
pch_gbe_main.c:(.text+0x510370): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x510393): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x5103b3): undefined reference to `pch_ch_control_write'
...
It's a regression by commit da1586461. The root cause is that
the CONFIG_PPS is not set there, consequently CONFIG_PTP_1588_CLOCK
can not be set anyway, which finally causes ptp_pch and pch_gbe_main
build failures.
As David prefers to use *select* to fix such module co-dependency issues,
this patch explicitly selects all the possible dependencies of PCH_PTP.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Haicheng Li <haicheng.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pulled mainline in order to get the UAPI infrastructure already
merged before I pull in David Howells's UAPI trees for networking.
Signed-off-by: David S. Miller <davem@davemloft.net>
i218 is the next-generation LOM that will be available on systems with the
Lynx Point LP Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support of those devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change limits the PF/VF driver to 9.5K max jumbo frame size in order
prevent a possible Tx hang in the adapter when sending frames between
pools.
All of the parts in ixgbe support a maximum frame of 15.5K for standard
traffic, however with SR-IOV or DCB enabled they should be limiting the
MTU size to 9.5K. Instead of adding extra checks which would have to
change the MTU when we go into or out of these modes it is preferred to
just use a standard 9.5K MTU limit for all modes so that this extra
overhead can be avoided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not setting the number of real Tx queues in the net_device
structure. This caused some serious issues such as Tx hangs and extremely
poor performance with some usages of the driver.
The issue is best observed by running:
iperf -c <host> -P <n>
Where n is greater than one. The greater the value of n the more likely
the problem is to show up.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
The following patch:
acb600d net: remove skb recycling
added dev_free_skb() to drivers/net/ethernet/freescale/ucc_geth.c
This is a typo and should be dev_kfree_skb(). This fixes this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current GRO can hold packets in gro_list for almost unlimited
time, in case napi->poll() handler consumes its budget over and over.
In this case, napi_complete()/napi_gro_flush() are not called.
Another problem is that gro_list is flushed in non friendly way :
We scan the list and complete packets in the reverse order.
(youngest packets first, oldest packets last)
This defeats priorities that sender could have cooked.
Since GRO currently only store TCP packets, we dont really notice the
bug because of retransmits, but this behavior can add unexpected
latencies, particularly on mice flows clamped by elephant flows.
This patch makes sure no packet can stay more than 1 ms in queue, and
only in stress situations.
It also complete packets in the right order to minimize latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E8001 on an ASUS P5NSLI motherboard is unable to send/receive
packets on a system with >4gb ram unless a 32bit DMA mask is used.
This issue has been around for years and a fix was sent 3.5 years ago, but
there was some debate as to whether it should instead be fixed as a PCI quirk.
http://www.spinics.net/lists/netdev/msg88670.html
However, 18 months later a similar workaround was introduced for another
chipset exhibiting the same problem.
http://www.spinics.net/lists/netdev/msg142287.html
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes type assignment issues, function definition and symbol
shadowing which triggered sparse warnings.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move() instead of list_del() + list_add().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sky2_probe() return 0 for success and negative value
for most of its internal tests failures. There are two exceptions
that are error cases going to err_out*:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function skge_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_led_off:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function gem_init_one() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_consistent:. For this error
case, the function abort its success execution path, but returns non
negative value, making it difficult for a caller function to notice
the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function niu_pci_init_one() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_res:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sh_eth_drv_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out_release:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sonic_probe1() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function au1000_probe() return 0 for success and negative value
for most of its internal tests failures. There are exceptions
that are error cases going to err_out:. For this cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function amd8111e_probe_one() return 0 for success and negative
value for most of its internal tests failures. There are two exceptions
that are error cases going to err_free_reg:. For this two cases, the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function qlcnic_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_free_netdev:. For this error case,
the function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sis900_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_out_cleardev:. Fore this error case,
the function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function natsemi_probe1() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to err_create_file:. Fore this error case the
function abort its success execution path, but returns non negative value,
making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function dmfe_init_one() return 0 for success and negative value
for most of its internal tests failures. There are three exceptions
that are error cases going to err_out_*:. Fore this three cases the
function abort its success execution path, but returns non negative
value, making it dificult for a caller function to notice the error.
This patch fixes the error cases that do not return negative values.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Late-breaking fix for IPoIB on mlx4 SR-IOV VFs.
- Fix for IPoIB build breakage with CONFIG_INFINIBAND_IPOIB_CM=n
(new netlink config changes are to blame).
- Make sure retry count values are in range in RDMA CM.
- A few nes hardware driver fixes and cleanups.
- Have iSER initiator use >1 interrupt vectors if available.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9Jv4
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband changes from Roland Dreier:
"Second batch of changes for the 3.7 merge window:
- Late-breaking fix for IPoIB on mlx4 SR-IOV VFs.
- Fix for IPoIB build breakage with CONFIG_INFINIBAND_IPOIB_CM=n (new
netlink config changes are to blame).
- Make sure retry count values are in range in RDMA CM.
- A few nes hardware driver fixes and cleanups.
- Have iSER initiator use >1 interrupt vectors if available."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Check that retry count values are in range
IB/iser: Add more RX CQs to scale out processing of SCSI responses
RDMA/nes: Bump the version number of nes driver
RDMA/nes: Remove unused module parameter "send_first"
RDMA/nes: Remove unnecessary if-else statement
RDMA/nes: Add missing break to switch.
mlx4_core: Adjust flow steering attach wrapper so that IB works on SR-IOV VFs
IPoIB: Fix build with CONFIG_INFINIBAND_IPOIB_CM=n
Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.
Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.
With help from Maxime Bizon, who pointed out that commit
87151b8689 (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.
Instead of fixing this bug, lets remove skb recycling.
Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Pull networking changes from David Miller:
"The most important bit in here is the fix for input route caching from
Eric Dumazet, it's a shame we couldn't fully analyze this in time for
3.6 as it's a 3.6 regression introduced by the routing cache removal.
Anyways, will send quickly to -stable after you pull this in.
Other changes of note:
1) Fix lockdep splats in team and bonding, from Eric Dumazet.
2) IPV6 adds link local route even when there is no link local
address, from Nicolas Dichtel.
3) Fix ixgbe PTP implementation, from Jacob Keller.
4) Fix excessive stack usage in cxgb4 driver, from Vipul Pandya.
5) MAC length computed improperly in VLAN demux, from Antonio
Quartulli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ipv6: release reference of ip6_null_entry's dst entry in __ip6_del_rt
Remove noisy printks from llcp_sock_connect
tipc: prevent dropped connections due to rcvbuf overflow
silence some noisy printks in irda
team: set qdisc_tx_busylock to avoid LOCKDEP splat
bonding: set qdisc_tx_busylock to avoid LOCKDEP splat
sctp: check src addr when processing SACK to update transport state
sctp: fix a typo in prototype of __sctp_rcv_lookup()
ipv4: add a fib_type to fib_info
can: mpc5xxx_can: fix section type conflict
can: peak_pcmcia: fix error return code
can: peak_pci: fix error return code
cxgb4: Fix build error due to missing linux/vmalloc.h include.
bnx2x: fix ring size for 10G functions
cxgb4: Dynamically allocate memory in t4_memory_rw() and get_vpd_params()
ixgbe: add support for X540-AT1
ixgbe: fix poll loop for FDIRCTRL.INIT_DONE bit
ixgbe: fix PTP ethtool timestamping function
ixgbe: (PTP) Fix PPS interrupt code
ixgbe: Fix PTP X540 SDP alignment code for PPS signal
...
To introduce generic set_bit_le() later, we remove our own definition
and use a proper non-atomic bitops function: __set_bit_le().
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are now standard functions for dealing with little-endian bit
arrays, so use them instead of our own implementations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Kirsher says:
====================
This series contains fixes/updates to ixgbe only. There are three
PTP fixes, polling loop fix and the addition of a device id (X540-AT1).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the InfiniBand stack does not support flow steering at the
verbs level -- the only usage of flow steering in the IB driver is for
L2 multicast attaches. We need to add the IB case to procedure
mlx4_QP_FLOW_STEERING_ATTACH_wrapper() to allow IPoIB to work on VFs
on ConnectX-3 when flow steering is enabled.
Currently, the IB case in mlx4_QP_FLOW_STEERING_ATTACH_wrapper() is missing,
so the procedure returns -EINVAL and IPoIB on VFs breaks.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit d760fc37b0 caused
1G functions to allocate rx rings which were 1/10 of the
size of 10G functions' rx rings.
However, it also caused 10G functions on 5771x boards to
allocate small rings, which limits their possible (default)
rx throughput. This patch causes all 10G functions to use
rings of intended length by default.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes memory allocation to reduce stack footprint
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds device support for Ethernet Controller X540-AT1.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The loop in ixgbe_reinit_fdir_tables_82599() only polls for up to 100us
resulting in failures to update the FDIR filter table at 1Gbps and 10Gbps
when under load.
The poll times for FDIRCTRL.INIT_DONE are 55us, 550us and 5.5ms for 10Gbps,
1Gbps and 100Mbps respectively.
This patch sets the wait time to be the same as in ixgbe_fdir_enable_82599()
Reported-by: Bhushan <shashi-sm@users.sf.net>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a development issue that occurred due to invalid modes reported
in the ethtool get_ts_info function. The issue is resolved by removing
unsupported modes from the Rx supported list.
CC: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver was enabling PPS interrupt even when user wasn't enabling it via the
ptp core. This patch fixes the PPS so that it is only enabled explicitly, and
moves the interrupt enabling code into the correct location in the driver
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug in the method used for calculating the trigger
alignment for SDP0 when enabling a PPS output on the X540. The alignment math
wasn't properly taking into account the overflow cyclecounter, and was
misaligning the pin triggers so that two X540 devices synced properly had
mis-aligned SDP pins. This patch fixes the math to calculate the correct
seconds alignment for the PPS signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
drivers/net/ethernet/broadcom/tg3.c:8121:8: warning: symbol 'i' shadows an earlier one
drivers/net/ethernet/broadcom/tg3.c:8003:6: originally declared here
drivers/net/ethernet/broadcom/tg3.c:785:5: warning: symbol 'tg3_ape_scratchpad_read' was not declared. Should it be static?
drivers/net/ethernet/broadcom/tg3.c:7781:19: warning: Using plain integer as NULL pointer
drivers/net/ethernet/broadcom/tg3.c:10231:31: error: bad constant expression
Reported-by: Fengguang Wu <fenguang.wu@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRV_MODULE_VERSION is smaller than the ->version buffer so the memcpy()
copies 1 byte past the end of the string. It's not super harmful, but
it makes the static checkers complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
chan->count is used by rx channel. If the desc count is not updated by
the clean up loop in cpdma_chan_stop, the value written to the rxfree
register in cpdma_chan_start will be incorrect.
Signed-off-by: Tao Hou <hotforest@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The config combination:
CONFIG_PCH_GBE=y
CONFIG_PCH_PTP=y
CONFIG_PTP_1588_CLOCK=m
doesn't work, because then you have a built-in kernel
object (the PCH_PTP code) referring to symbols in a
module (PTP_1588_CLOCK).
Fix this like IXGBE, by using "select PTP_1588_CLOCK"
instead of a "depends on".
Reported-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- mlx4 IB support for SR-IOV
- A couple of SRP initiator fixes
- Batch of nes hardware driver fixes
- Fix for long-standing use-after-free crash in IPoIB
- Other miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PAcy
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"First batch of InfiniBand/RDMA changes for the 3.7 merge window:
- mlx4 IB support for SR-IOV
- A couple of SRP initiator fixes
- Batch of nes hardware driver fixes
- Fix for long-standing use-after-free crash in IPoIB
- Other miscellaneous fixes"
This merge also removes a new use of __cancel_delayed_work(), and
replaces it with the regular cancel_delayed_work() that is now irq-safe
thanks to the workqueue updates.
That said, I suspect the sequence in question should probably use
"mod_delayed_work()". I just did the minimal "don't use deprecated
functions" fixup, though.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (45 commits)
IB/qib: Fix local access validation for user MRs
mlx4_core: Disable SENSE_PORT for multifunction devices
mlx4_core: Clean up enabling of SENSE_PORT for older (ConnectX-1/-2) HCAs
mlx4_core: Stash PCI ID driver_data in mlx4_priv structure
IB/srp: Avoid having aborted requests hang
IB/srp: Fix use-after-free in srp_reset_req()
IB/qib: Add a qib driver version
RDMA/nes: Fix compilation error when nes_debug is enabled
RDMA/nes: Print hardware resource type
RDMA/nes: Fix for crash when TX checksum offload is off
RDMA/nes: Cosmetic changes
RDMA/nes: Fix for incorrect MSS when TSO is on
RDMA/nes: Fix incorrect resolving of the loopback MAC address
mlx4_core: Fix crash on uninitialized priv->cmd.slave_sem
mlx4_core: Trivial cleanups to driver log messages
mlx4_core: Trivial readability fix: "0X30" -> "0x30"
IB/mlx4: Create paravirt contexts for VFs when master IB driver initializes
mlx4: Modify proxy/tunnel QP mechanism so that guests do no calculations
mlx4: Paravirtualize Node Guids for slaves
mlx4: Activate SR-IOV mode for IB
...
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
Ben Hutchings says:
====================
Some bug fixes that should go into 3.7:
1. Fix oops when removing device with SR-IOV enabled. (This regression
was introduced by the last set of changes, so the fix does not need to
be applied to any earlier kernel versions.)
2. Fix firmware structure field lookup bug that resulted in missing
sensor information.
3. Fix bug that makes self-test do very little in some configurations.
4. Fix the numbering of ethtool RX flow steering filters to reflect the
real hardware priorities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO1fAAoJEIwa5zzehBx3IPgP/jxoO1flVGNVf0reqqyDro/w
prZmp8cNVH9uv8xG9n9vawObrMQ8M6jCJ449fEWuAZ58EXrpIPd0kkm/MOmxp8K1
LNs+q2aXxWpD488+b3RK55g3fksqZutTbn3y6HNuCoLG9l8yT/95KX4IIzfEP2Ch
1TCNHdkTbf37nTBOmKN0x1kahGpWDrOkf9ysHQq+DXAGF4uwNwtR194dqz3HbDND
hZqRq7qCLn9OwGRGNicPFoB6UcxwZ/+/+u5sX7nqPGoiPofg977mhWk1DFO15EM3
S+A6g0dZ+XLsL+fFtOl4snSmrG5Et6qTOP0/ItQJgTG+5YdCS09ohCWJwRCBHbgj
M5arOkyGFdVAlvX7cUux374sMe0AcqUsEmt79mYuBpIE+pBJaRUoCgDcs9FDZeUB
U6WcE4AkxMtW7DtmVW+mF4ls9/K6cRXgWMuHCUmt1o3m3Ly9ITT7j+ntXnD9nuYk
ndoVLR6Vxk2BzlkD0JEtg7FRAS9Wgo2DBix05qM1Qkut2iIZRhFQlqJQpNbeNdii
/3Lg/hqpAVTZKGCd+paegHez61meyFz2PB2IiE0JKANhKHRCWTWRGgKIXkGyCiXk
wJ2iRCOlMEpmpJgCBzfI32ER/hnW4s64iDjgksEwz6pEt7xCbhwgmwrpf0H0KsSF
rLroHOMqyISd/Ha52Vin
=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Each RX filter table contains filters with two different levels of
specificity: TCP/IPv4 and UDP/IPv4 filters match the local address and
port and optionally the remote address and port; Ethernet filters
match the local address and optionally the VID. The more specific
filters always override less specific filters within the same table,
and should be numbered accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This filter flag cannot yet be set through the ethtool command and
will not be supported on future hardware.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The loopback self-test iterates over all the TX queues of channel 0,
which is not very interesting when that's an RX-only channel.
Signed-off-by: Ben Hutchings <bhutchings@solarflre.com>
The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword. In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Commit c31e5f9 ('sfc: Add channel specific receive_skb handler and
post_remove callback') added the function pointer field
efx_channel_type::post_remove and an unconditional call through it.
This field should have been initialised to efx_channel_dummy_op_void
in the existing instances of efx_channel_type, but this was only done
in efx_default_channel_type. Consequently, if a device has SR-IOV
enabled then removing the driver or device will result in an oops.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Later changes need to be able to refer to neighbour attributes
when doing fdb_add.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is the seldom used corner case where HWMON=m at the same
time as TIGON3=y (typically randconfigs) which will cause a link
fail like:
drivers/built-in.o: In function `tg3_close':
tg3.c:(.text+0x16bd86): undefined reference to `hwmon_device_unregister'
drivers/built-in.o: In function `tg3_hwmon_open':
tg3.c:(.text+0x16fc4b): undefined reference to `hwmon_device_register'
make[1]: *** [vmlinux] Error 1
Fix it as suggested by DaveM[1] by having the Kconfig logic simply
select HWMON when TIGON3 is selected. This gets rid of all the
extra IS_ENABLED ifdeffery in tg3.c as a side benefit.
[1] http://marc.info/?l=linux-netdev&m=134250573718151&w=2
Cc: Michael Chan <mchan@broadcom.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Anisse Astier <anisse@astier.eu>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d755998270.
It wasn't meant to be applied, commit
342b7b741d ("net: ti cpsw ethernet: set
IFCTL_A bit in MACCONTROL") was redone in such a way to make this
commit unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to specify the phy interface of the CPSW slaves. The new
node parameter is called "phy_if_mode" and is optional. The original
behaviour of the driver is preserved when not given.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RMII/RGMII mode operation in 100Mbps, the CPSW needs to set the
IFCTL_A bits in the MACCONTROL register. For all other PHY modes, this
bit is unused, so setting it unconditionally shouldn't cause any
trouble.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit e22979d96a (mlx4_en: Moving to Interrupts for TX
completions) we no longer need to orphan skbs in mlx4_en_xmit()
since skb wont stay a long time in TX ring before their release.
Orphaning skbs in ndo_start_xmit() should be avoided as much as
possible, since it breaks TCP Small Queue or other flow control
mechanisms (per socket limits)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.
A short summary of minor bugs fixed by this FW:
1. In switch dependent mode, fix several issues regarding inner vlan
vs. DCB priorities.
2. iSCSI - not all packets were completed on a forward channel.
3. DCB - fixed for 4-port devices.
4. Fixed false parity reported in CAM memories when operating near -5%
on the 1.0V core supply.
5. ETS default settings are set to fairness between traffic classes
(rather than strict priority), and uses the same chip receive buffer
configuration for both PFC and pause.
For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current VFs enumeration algorithm used in be_find_vfs does not take domain
number into the match. The match found in igb/ixgbe is more elegant and
safe.
This 2nd version uses pci_physfn instead of checking dev->physfn directly.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we skipped the merge window for 3.6-rc1 for the tty tree, everything
is now settled down and working properly, so we are ready for 3.7-rc1.
Here's the patchset, it's big, but the large changes are removing a
firmware file and adding a staging tty driver (it depended on the tty
core changes, so it's going through this tree instead of the staging
tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp36oACgkQMUfUDdst+yk4WgCdEy13hot8fI2Lqnc7W0LKu7GX
4p8AoLTjzrXhLosxdijskDQ9X1OtjrxU
=S5Ng
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY changes from Greg Kroah-Hartman:
"As we skipped the merge window for 3.6-rc1 for the tty tree,
everything is now settled down and working properly, so we are ready
for 3.7-rc1. Here's the patchset, it's big, but the large changes are
removing a firmware file and adding a staging tty driver (it depended
on the tty core changes, so it's going through this tree instead of
the staging tree.)
All of these patches have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up more-or-less trivial conflicts in
- drivers/char/pcmcia/synclink_cs.c:
tty NULL dereference fix vs tty_port_cts_enabled() helper function
- drivers/staging/{Kconfig,Makefile}:
add-add conflict (dgrp driver added close to other staging drivers)
- drivers/staging/ipack/devices/ipoctal.c:
"split ipoctal_channel from iopctal" vs "TTY: use tty_port_register_device"
* tag 'tty-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (235 commits)
tty/serial: Add kgdb_nmi driver
tty/serial/amba-pl011: Quiesce interrupts in poll_get_char
tty/serial/amba-pl011: Implement poll_init callback
tty/serial/core: Introduce poll_init callback
kdb: Turn KGDB_KDB=n stubs into static inlines
kdb: Implement disable_nmi command
kernel/debug: Mask KGDB NMI upon entry
serial: pl011: handle corruption at high clock speeds
serial: sccnxp: Make 'default' choice in switch last
serial: sccnxp: Remove mask termios caps for SW flow control
serial: sccnxp: Report actual baudrate back to core
serial: samsung: Add poll_get_char & poll_put_char
Powerpc 8xx CPM_UART setting MAXIDL register proportionaly to baud rate
Powerpc 8xx CPM_UART maxidl should not depend on fifo size
Powerpc 8xx CPM_UART too many interrupts
Powerpc 8xx CPM_UART desynchronisation
serial: set correct baud_base for EXSYS EX-41092 Dual 16950
serial: omap: fix the reciever line error case
8250: blacklist Winbond CIR port
8250_pnp: do pnp probe before legacy probe
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
In the current driver, the SENSE_PORT firmware command is issued as a
"wrapped" command, but the command handling code doesn't have a
wrapper, so it will never do anything other than log an error message.
The latest ConnectX-3 2.11.500 firmware reports the SENSE_PORT
capability even in multi-function (SR-IOV) mode, so the driver will
try to issue the command.
At least until the driver has a proper wrapper for SENSE_PORT, make
sure we disable the command for multi-function devices.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Instead of having a hard-coded "PCI device ID != 0x1003" (which
obviously breaks as newer devices with ID != 0x1003 become available),
instead let's set a flag in our PCI device table for the older devices
where we're supposed to force using SENSE_PORT. This also avoids
enabling SENSE_PORT for virtual functions by mistake.
Signed-off-by: Roland Dreier <roland@purestorage.com>
That way we can check flags later on, when we've finished with the
pci_device_id structure. Also convert the "is VF" flag to an enum:
"Never do in the preprocessor what can be done in C."
Signed-off-by: Roland Dreier <roland@purestorage.com>
On an SR-IOV master device, __mlx4_init_one() calls mlx4_init_hca()
before mlx4_multi_func_init(). However, for unlucky configurations,
mlx4_init_hca() might call mlx4_SENSE_PORT() (via mlx4_dev_cap()), and
that calls mlx4_cmd_imm() with MLX4_CMD_WRAPPED set.
However, on a multifunction device with MLX4_CMD_WRAPPED, __mlx4_cmd()
calls into mlx4_slave_cmd(), and that immediately tries to do
down(&priv->cmd.slave_sem);
but priv->cmd.slave_sem isn't initialized until mlx4_multi_func_init()
(which we haven't called yet). The next thing it tries to do is access
priv->mfunc.vhcr, but that hasn't been allocated yet.
Fix this by moving the initialization of slave_sem and vhcr up into
mlx4_cmd_init(). Also, since slave_sem is really just being used as a
mutex, convert it into a slave_cmd_mutex.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Previously, the structure of a guest's proxy QPs followed the
structure of the PPF special qps (qp0 port 1, qp0 port 2, qp1 port 1,
qp1 port 2, ...). The guest then did offset calculations on the
sqp_base qp number that the PPF passed to it in QUERY_FUNC_CAP().
This is now changed so that the guest does no offset calculations
regarding proxy or tunnel QPs to use. This change frees the PPF from
needing to adhere to a specific order in allocating proxy and tunnel
QPs.
Now QUERY_FUNC_CAP provides each port individually with its proxy
qp0, proxy qp1, tunnel qp0, and tunnel qp1 QP numbers, and these are
used directly where required (with no offset calculations).
To accomplish this change, several fields were added to the phys_caps
structure for use by the PPF and by non-SR-IOV mode:
base_sqpn -- in non-sriov mode, this was formerly sqp_start.
base_proxy_sqpn -- the first physical proxy qp number -- used by PPF
base_tunnel_sqpn -- the first physical tunnel qp number -- used by PPF.
The current code in the PPF still adheres to the previous layout of
sqps, proxy-sqps and tunnel-sqps. However, the PPF can change this
layout without affecting VF or (paravirtualized) PF code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is necessary in order to support > 1 VF/PF in a VM for software
that uses the node guid as a discriminator, such as librdmacm.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove the error returns for IB ports from mlx4_ib_add,
mlx4_INIT_PORT_wrapper, and mlx4_CLOSE_PORT_wrapper.
Currently, SRIOV is supported only for devices for which the
link layer is IB on all ports; RoCE support will be added later.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Allow only master to change node description.
2. Prevent AH leakage in send mads.
3. Take device part number from PCI structure, so that guests see the
VF part number (and not the PF part number).
4. Place the device revision ID into caps structure at startup.
5. SET_PORT in update_gids_task needs to go through wrapper on master.
6. In mlx4_ib_event(), PORT_MGMT_EVENT needs be handled in a work
queue on the master, since it propagates events to slaves using
GEN_EQE.
7. Do not support FMR on slaves.
8. Add spinlock to slave_event(), since it is called both in interrupt
context and in process context (due to 6 above, and also if
smp_snoop is used). This fix was found and implemented by Saeed
Mahameed <saeedm@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Normally, INIT_PORT and CLOSE_PORT are invoked when special QP0
transitions to RTR, or transitions to ERR/RESET respectively.
In SR-IOV mode, however, the master is also paravirtualized. This in
turn requires that we not do INIT_PORT until the entire QP0 path (real
QP0 and proxy QP0) is ready to receive. When the real QP0 goes down,
we should indicate that the port is not active.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Slaves may not set the IS_SM capability for the port.
2. DEV_MGMT may not be set in multifunction mode.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
P_Key change and guid change events are not of interest to all slaves,
but only to those slaves which "see" the table slots whose contents
have change.
For example, if the guid at port 1, index 5 has changed in the PPF, we
wish to propagate the gid-change event only to the function which has
that guid index mapped to its port/guid table (in this case it is
slave #5). Other functions should not get the event, since the event
does not affect them.
Similarly with P_Keys -- P_Key change events are forwarded only to
slaves which have that P_Key index mapped to their virtual P_Key table.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For IB ports, we paravirtualize the GUID at index 0 on slaves. The
GUID at index 0 seen by a slave is the actual GUID occupying the GUID
table at the slave-id index.
The driver, by default, requests at startup time that subnet manager
populate its entire guid table with GUIDs. These guids are then mapped
(paravirtualized) to the slaves, and appear for each slave as its GUID
at index 0.
Until each slave has such a guid, its port status is DOWN.
The guid table is cached to support special QP paravirtualization, and
event propagation to slaves on guid change (we test to see if the guid
really changed before propagating an event to the slave).
To support this caching, add capability to __mlx4_ib_query_gid() to
obtain the network view (i.e., physical view) gid at index X, not just
the host (paravirtualized) view.
Based on a patch from Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For an IB port, a slave should not show port active until that slave
has a valid alias-guid (provided by the subnet manager). Therefore
the port-up event should be passed to a slave only after both the port
is up, and the slave's alias-guid has been set.
Also, provide the infrastructure for propagating port-management
events (client-reregister, etc) to slaves.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MAD_IFC firmware command fulfills two functions.
First, it is used in the QP0/QP1 MAD-handling flow to obtain
information from the FW (for answering queries), and for setting
variables in the HCA (MAD SET packets).
For this, MAD_IFC should provide the FW (physical) view of the data.
This is the view that OpenSM needs. We call this the "network view".
In the second case, MAD_IFC is used by various verbs to obtain data
regarding the local HCA (e.g., ib_query_device()). We call this the
"host view".
This data needs to be paravirtualized.
MAD_IFC therefore needs a wrapper function, and also needs another
flag indicating whether it should provide the network view (when it is
called by ib_process_mad in special-qp packet handling), or the host
view (when it is called while implementing a verb).
There are currently 2 flag parameters in mlx4_MAD_IFC already:
ignore_bkey and ignore_mkey. These two parameters are replaced by a
single "mad_ifc_flags" parameter, with different bits set for each
flag. A third flag is added: "network-view/host-view".
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This requires:
1. Replacing the paravirtualized P_Key index (inserted by the guest)
with the real P_Key index.
2. For UD QPs, placing the guest's true source GID index in the
address path structure mgid field, and setting the ud_force_mgid
bit so that the mgid is taken from the QP context and not from the
WQE when posting sends.
3. For UC and RC QPs, placing the guest's true source GID index in the
address path structure mgid field.
4. For tunnel and proxy QPs, setting the Q_Key value reserved for that
proxy/tunnel pair.
Since not all the above adjustments occur in all the QP transitions,
the QP transitions require separate wrapper functions.
Secondly, initialize the P_Key virtualization table to its default
values: Master virtualized table is 1-1 with the real P_Key table,
guest virtualized table has P_Key index 0 mapped to the real P_Key
index 0, and all the other P_Key indices mapped to the reserved
(invalid) P_Key at index 127.
Finally, add logic in smp_snoop for maintaining the phys_P_Key_cache.
and generating events on the master only if a P_Key actually changed.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allocate SR-IOV paravirtualization resources and MAD demuxing contexts
on the master.
This has two parts. The first part is to initialize the structures to
contain the contexts. This is done at master startup time in
mlx4_ib_init_sriov().
The second part is to actually create the tunneling resources required
on the master to support a slave. This is performed the master
detects that a slave has started up (MLX4_DEV_EVENT_SLAVE_INIT event
generated when a slave initializes its comm channel).
For the master, there is no such startup event, so it creates its own
tunneling resources when it starts up. In addition, the master also
creates the real special QPs. The ib_core layer on the master causes
creation of proxy special QPs, since the master is also
paravirtualized at the ib_core layer.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In addition, pass the proxy and tunnel QP numbers to slaves so the
driver can perform special QP paravirtualization.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This innocent print makes it very hard to actually use the mlx4_core
debug messages -- for example, the module load sequence of a device
with two VFs yielded 3200 debug prints, with 2800 of them being this
one. Let's just remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The wrong offset was used when parsing the number of XRCs in
mlx4_QUERY_DEV_CAP().
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Added and modified a few log messages mostly in probe path.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) link_status_query() is always called to query the link-speed (speed
after applying qos). When there is no qos setting, link-speed is derived from
port-speed. Do all this inside this routine and hide this from the callers.
2) adpater->phy.forced_port_speed is not being set anywhere after being
initialized. Get rid of this variable.
3) Ignore async link_speed notifications till the initial value has been
fetched from FW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All invocations of this routine use the same type value.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple round-robin hardware TX scheduling can cause starvation of TX rings
with small packets when other TX rings have large TSO or jumbo packets.
In the simplest case, consider 2 TCP streams running in opposite
directions. The TSO TX traffic will hash to one ring and the ACKs for the
incoming data on a different TCP connection will hash to a different TX
ring. The hardware fetches one complete TSO packet (up to 64K data)
before servicing the other TX ring. When it gets to the other TX ring, it
will only fetch one packet (64-byte ACK packet in this case). After that,
it will switch back to the 1st ring filled with more TSO packets. Because
only one ACK can go out roughly every 500 usec in this case, the incoming
data rate becomes very low.
Update version to 3.125.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default remains the same.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by introducing tg3_stop() that does the opposite of tg3_start(). This
function will be useful when adding the support for changing the numbe
of rx and tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by introducing tg3_start() that handles all initialization steps from
IRQ allocation. This function will be needed when adding support for
changing the number of rx and tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since the number of rings can be different.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_cnt is no longer necessarily equal to the number rx or tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation work to allow the number of RX and TX rings to be
configured separately.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 51af6d7c1f.
Breaks the build with CONFIG_PCI_ATS not enabled.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c0357e975a modified bnx2 to switch from
using ioremap/iounmap to pci_iomap/pci_iounmap. They missed a spot in the error
path of bnx2_init_one though. This patch just cleans that up.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Michael Chan <mcan@broadcom.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC can't see that in all non-error-return paths we do in fact
set *using_dac to something.
Add an explicit initialization to remove this warning:
drivers/net/ethernet/brocade/bna/bnad.c: In function ‘bnad_pci_probe’:
drivers/net/ethernet/brocade/bna/bnad.c:3079:5: warning: ‘using_dac’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/brocade/bna/bnad.c:3233:7: note: ‘using_dac’ was declared here
Signed-off-by: David S. Miller <davem@davemloft.net>
Current VFs enumeration algorithm used in be_find_vfs does not take domain
number into the match. The match found in igb/ixgbe is more elegant and
safe.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new common code routine to upgrade an adapter's
firmware. This routine handles all of the complexities of working with the
the existing adapter firmware in order to quiesce the adapter and uP, etc.
For an automatic upgrade it will send a HELLO command to check if cxgb4
want/can upgrade firmware, i.e. if cxgb4 is MASTER and has newer firmware
that it wants to load and call the new common code routine t4_fw_upgrade.
Note that it should not issue a RESET command after a successful firmware
upgrade.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a card had already been initialized, on reloading cxgb4 driver firmware
required an upgrade but the upgrade did not happen. In that case a mailbox
timeout would occur during T4 configuration file stuff. The fix is to let the
caller know the firmware was not upgraded so a reset would be issued before
starting the T4 config stuff.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case if user defined configuration file at /lib/firmware/cxgb4/t4-config.txt
location and also factory default configuration file written to FLASH are not
present then driver will use hardwired configuration settings.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with T4 firmware version 1.3.11.0 the firmware now supports device
configuration via a Firmware Configuration File. The Firmware Configuration
File was primarily developed in order to centralize all of the configuration,
resource allocation, etc. for Unified Wire operation where multiple
Physical / Virtual Function Drivers would be using a T4 adapter simultaneously.
The Firmware Configuration file can live in three locations as shown below
in order of precedence.
1) User defined configuration file: /lib/firmware/cxgb4/t4-config.txt
2) Factory Default configuration file written to FLASH within
the manufacturing process.
3) Hardwired driver configuration.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new enums and macros to enable T4 configuration file support. It
also removes duplicate macro definitions.
It fixes the build failure in cxgb4vf driver introduced because of old macro
definition removal.
It also performs SGE initialization based on T4 configuration file is provided
or not. If it is provided then it uses the parameters provided in it otherwise
it uses hard coded values.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements two new functions t4_mem_win_read and t4_memory_read.
These new functions can be used to read memory via the PCIE memory window.
Please note, for proper execution of these functions PCIE_MEM_ACCESS_BASE_WIN
registers must be setup correctly like how setup_memwin in the cxgb4 driver
does it.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MIPSsim platform is no longer supported or used. This patch
deletes the Ethernet driver.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is primarily to address transmission timeout occurrences, when
multiple H/W Tx queues are being used concurrently. Because in
the priority scheduling mode the controller does not service the
Tx queues equally (but in ascending index order), Tx timeouts are
being triggered rightaway for a basic test with multiple simultaneous
connections like:
iperf -c <server_ip> -n 100M -P 8
resulting in kernel trace:
NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255
...
and controller reset during intense traffic, and possibly further
complications.
This patch changes the default H/W Tx scheduling setting (TXSCHED)
for multi-queue devices, from priority scheduling mode to a weighted
round robin mode with equal weights for all H/W Tx queues, and
addresses the issue above.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the definition of bnx2x_tests_str_arr from static char
pointer to static const char bi-directional array. Also the
bnx2x_get_strings function is simplified.
Reported-by: Joe Perches <joe@perches.com>
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent kernel changes we can now return errors on a failure to setup a
VLAN filter. This patch takes advantage of that opportunity so that we can
return either an EIO error in the case of a mailbox failure, or an EACCESS
error in the case of being denied access to the VLAN filter table by the
PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes the ixgbevf driver so that it can correctly drop a frame
should it receive a jumbo frame.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While fixing up a patch from Alex Duyck to use q_vectors in ring containers
to update the ITR I bungled it and missed actually updating the counters
in the ring container q_vectors. This patch fixes my mistake and makes
interrupt moderation actually work.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove 'rx_ring' parameter as it is not used in ixgbevf_receive_skb
Signed-off-by: Narendra K <narendra_k@dell.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The counter is not valid unless the controller is running in IOV mode.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF driver was not designed to correctly handle a message timeout. As
a result it is possible for one bad message to invalidate all messages
following it until the part is reset. Instead we should copy the example
in igbvf of how to handle a mailbox event and message timeout.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We're now using isa_virt_to_bus(), and there really
isn't a generic and consistent test for whether a
platform provides this interface or not.
This driver is also for an x86-only device.
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This change is meant to improve performance on systems that do not require
the DMA unmap calls. On those systems we do not need to make use of the
unmap address for Tx or the unmap length so we can drop both thereby
reducing the size of the Tx buffer info structure.
In addition I have changed the logic to check for unmap length instead of
unmap address when checking to see if a buffer needs to be unmapped from
DMA use. The reasons for this change is that on some platforms it is
possible to receive a valid DMA address of 0 from an IOMMU.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of storing the RSS key as a character array we can simplify the
configuration by making it a u32 array. This allows us to just write one
value per register without any unnecessary operations to construct the
value.
This change will produce the same exact key, the only difference is that I
translated the u8 array to a u32 array which will be correctly ordered on
writes to hardware by the cpu_to_le32 operations that are built into the
writel calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up our RSS indirection table configuration so that we
generate the same table regardless of CPU endianness. In addition it
changes the table setup so that instead of doing a modulo based setup it is
instead a divisor based setup. The advantage to this is that we should be
able to take the Rx hash and compute the Rx queue with very little CPU
overhead if needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that Tx cleanup is done in a do/while loop instead
of a for loop. The main motivation behind this is the fact that we should
never be invoked with a budget less than 1 so we can skip checking the
budget before processing the first descriptor.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
