With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled. Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag. It only
used twice in non-fast paths. This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the __tg3_set_mac_addr() function earlier in the file
listing, to avoid a function prototype, and calls the function to
restore the LAA after a driver unload chip reset. With this code in
place, the administrator can wake the machine using the LAA.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.
When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames. Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver. The first hunk of this patch preserves this setting.
The second hunk of this patch wipes out the driver present signature of
the APE memory space. By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the existing APE register mapping code with a call
to pci_ioremap_bar(). The code that maps the main device register space
did not undergo a similar change because the information derived from
the pci_resource_start() and pci_resource_len() is still used to
populate the (optional) mem_start and mem_end netdevice members.
Replace hardcoded constants where appropriate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 5761S chip variants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc_drv_probe() is the platform_driver probe function and it is only
called during init. Further, it calls smc_probe() which is marked as __init
already.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This eliminates the following often-generated warning from my 64 bit
Opteron SMP test stand:
eth0: too many iterations (6) in nv_nic_irq
According to the web, the problem is that the forcedeth driver has a
too-low value for max_interrupt_work. Grepping the kernel I see that
forcedeth has the second lowest value of all ethernet drivers (ie, 6).
Most are in the 20-40 range. So this patch increases this a bit, from 6
to 15 (at 15 forcedeth becomes the driver with third-lowest
max_interrupt_work value).
My test stand, which used to print out the above warnings repetitively
whenever it was under heavy net load, no longer does so.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do some cleanup on timer usage in this driver:
* Use round_jiffies to align wakeups and reduce power.
* Remove atl1_watchdog which does nothing but rearm itself
* Use setup_timer() function
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is now a net_device_stats structure inside net_device that should
be used if possible by devices. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It was being discussed where we would put this, but now it found a home
so use its define.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_keyreset returns true in either branch.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If card is using downloadable firmware (like Agere 9.x), firmware has
to be reloaded during resume. It is not possible to use request_firmware
for that, because tasks are still frozen, so request_firmware will
just timeout and fail. So cache firmware image in memory for later
reuse in ->resume method.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On resume card state is likely lost so we have to reload firmware
again.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
*Properly get/set all available ISR/IMR values and review common/uncommon bits
*Better handling of per-txq interrupts (we can now resolve what q is generating
each interrupt -this will help in debuging wme later)
*Some minor updates from legacy-hal
*Properly handle RXNOFRM and TXNOFRM interrupt masking (even when we don't set
them on IMR they keep showing up, so we disable them by zeroing AR5K_RXNOFRM
and AR5K_TXNOFRM registers). This doesn't exist on legacy-hal but i've tested
it on various cards and it works fine.
Changes-Licensed-under: ISC
Signed-Off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reclaim flag should include REPLY_RX_MPDU_CMD in the list of commands
issued by uCode. This is for safety in case the SEQ_RX_FRAME bit is set
incorrectly.
Signed-off-by: Daniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem fixed here is that iwl3945_mac_get_tsf() returns 0, as the
function is not implemented, and this is considered as a valid value by
the mac layer in mlme.c:1605. The consequence is that the STA in ad-hoc
mode is inserted/removed quite frequently due to IBSS merging.
This patch fixes :
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1781
and https://bugzilla.redhat.com/show_bug.cgi?id=459401
Signed-off-by: Fabrice Bellet <fabrice@bellet.info>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch drops unreadable usage of IWL_SET/GET_BITS16 in byte count
tables handling
This patch also cleans a bit the byte count table code and adds
WARN_ON traps on invalid values
This patch is pure cleanup, no functional changes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver does not properly convert rate_n_flags to PLCP index for mimo3
packets. This makes mac80211 drop the packets
Signed-off-by: Daniel C. Halperin <daniel.c.halperin@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since calibration framework is not HW specific remove 5000 and 4965 prefix
This patch doesn't provide any functional changes only code renaming
and movement
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses new parameters eeprom_ver and eeprom_calib_ver
to support additional HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure that station table is not accessed
with invalid station id in 4965 TX response path
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch utilize 5000 new TX response command
which contains all necessary information and avoids
back referencing to the original TX frame.
It also change handling of software queue tracking
4965 flow is aligned with changes as much as possible.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were also changing tx power even when we were not asked to,
this enforces the change only when we are asked nicely. When
not asked we simply try to use the max power, we don't tx power
at all for rate control.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables hardware interrupt mitigation on RX.
It should alleviate system interrupt load intelligently.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sc_txintrperiod is currently set to 0 and never updated. We won't
be using this, if anything we will consider using TX interrupt
mitigation but that is different and not yet tested. So remove
sc_txintrperiod and the pointless spin_lock_bh() on tx prepare.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unnecessary and of questionable value. Also remove
is_empty_ssid, as it is also unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs_create_bool() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the rt2x00 driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the ath5k driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A compilation with the command "make C=2 CF="-D__CHECK_ENDIAN__" \
drivers/net/wireless/hostap/"
yields the following warnings:
CHECK drivers/net/wireless/hostap/hostap_info.c
drivers/net/wireless/hostap/hostap_info.c:156:43: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:156:43: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:156:43: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:294:44: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:294:44: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:294:44: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:487:12: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:487:12: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:487:12: got long *<noident>
drivers/net/wireless/hostap/hostap_info.c:491:12: warning: incorrect type in
argument 2 (different signedness)
drivers/net/wireless/hostap/hostap_info.c:491:12: expected unsigned long
volatile *addr
drivers/net/wireless/hostap/hostap_info.c:491:12: got long *<noident>
The warnings are fixed with the following compile-tested fix:
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch protects iwl-csr.h and iwl-fh.h from double inclusion
by ifndef define endif idiom
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes most/all? of the "magic" numbers and unknown structure
variables inside the code and replaces them with meaningful prototypes.
(Plus a one line warning fix from Larry Finger <Larry.Finger@lwfinger.net>.)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch initialize all remaining values which are necessary for
SPI firmwares.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have to be careful if multiple "control frames" are passed in a very short intervals to
the device's firmware. As p54_assign_address always put them into same memory location.
To guarantee that this won't happen anymore, we have to treat control frames like normal
data frames in the devices own memory management.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the long names and the nesting in p54_rx_frame_sent really
became a "line longer than 80 characters" problem.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch series hopefully increases p54's "longterm" stability.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes clear that tx command is attached to the same tfd as
the tx packet
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
