The MAC stats are per-port and will only be displayed on the PF
with control of the link (one per physical port). Vadapter stats
will also be displayed for this PF, so distinguish the MAC stats
by adding a prefix of "port_".
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On every adapter there will be one primary PF per adaptor and
one link control PF per port.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is a stylistic change and does not affect
functionality.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where we have multiple functions (PFs and VFs), this
sysfs entry is useful to identify the physical port corresponding
to the function we are interested in.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksey Makarov says:
====================
net: thunderx: fix problems reported by static check tools
These are fixes for the problems that were reported by static check tools.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
GFP_KERNEL should be used in the thread context
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to cast void* to u8*: pointer arithmetics
works same way for both.
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a copypaste bug that was discovered by a static analysis
tool:
The patch 4863dea3fa: "net: Adding support for Cavium ThunderX
network controller" from May 26, 2015, leads to the following static
checker warning:
drivers/net/ethernet/cavium/thunder/nicvf_ethtool.c:517
nicvf_set_rxfh()
warn: we tested 'hkey' before and it was 'false'
drivers/net/ethernet/cavium/thunder/nicvf_ethtool.c
506 /* We do not allow change in unsupported parameters */
507 if (hkey ||
^^^^
We return here.
508 (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc !=
ETH_RSS_HASH_TOP))
509 return -EOPNOTSUPP;
510
511 rss->enable = true;
512 if (indir) {
513 for (idx = 0; idx < rss->rss_size; idx++)
514 rss->ind_tbl[idx] = indir[idx];
515 }
516
517 if (hkey) {
^^^^
So this is dead code.
518 memcpy(rss->key, hkey, RSS_HASH_KEY_SIZE *
sizeof(u64));
519 nicvf_set_rss_key(nic);
520 }
521
522 nicvf_config_rss(nic);
523 return 0;
524 }
regards,
dan carpenter
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse messages like this:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:1141:26: sparse: symbol
'nicvf_get_stats64' was not declared. Should it be static?
Also remove unused declarations
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They were left from development stage
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse message:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:385:40: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse message:
drivers/net/ethernet/cavium/thunder/nicvf_main.c:153:25: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes sparse messages like this:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:897:24: sparse:
constant 0x300000000000 is so big it is long
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are duplicate NODE_ID macro definitions. Move all of them to
nic.h for usage in nic and bgx driver and introduce nic_get_node_id()
helper function.
This patch also fixes 64bit mask which should have been ULL by
reworking the node calculation.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai says:
====================
cxgb4/cxgb4vf: Adds support for Chelsio T6 adapter
This patch series adds the following:
Adds NIC driver support for T6 adapter
Adds vNIC driver support for T6 adapter
This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
Thanks
V2:
Fixed compilation issue, when CHELSIO_T4_FCOE is set
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds vnic driver register related changes for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds NIC driver related changes for T6 adapter. Register related
changes, MC related changes, VF related changes, doorbell related
changes, debugfs changes, etc
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds new macro is_t6 and adds the register address range for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
Duyck and Steffen Klassert.
2) Revert ethtool PHY query change, it wasn't correct. The PHY address
selected by the driver running the PHY to MAC connection decides
what PHY address GET ethtool operations return information from.
3) Fix handling of sequence number bits for encryption IV generation in
ESP driver, from Herbert Xu.
4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
when there are other packets in the receive queue which is wrong.
Just respect the error returned from the generic socket recv
datagram helper. From Eric Dumazet.
5) Fix BNA driver firmware loading on big-endian systems, from Ivan
Vecera.
6) Fix regression in that we were inheriting the congestion control of
the listening socket for new connections, the intended behavior
always was to use the default in this case. From Neal Cardwell.
7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.
8) OTP parsing fix in iwlwifi from Liad Kaufman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
vti6: Add pmtu handling to vti6_xmit.
Revert "net: core: 'ethtool' issue with querying phy settings"
bnx2x: Move statistics implementation into semaphores
xen: netback: read hotplug script once at start of day.
xen: netback: fix printf format string warning
Revert "netfilter: ensure number of counters is >0 in do_replace()"
net: dsa: Properly propagate errors from dsa_switch_setup_one
tcp: fix child sockets to use system default congestion control if not set
udp: fix behavior of wrong checksums
sfc: free multiple Rx buffers when required
bna: fix soft lock-up during firmware initialization failure
bna: remove unreasonable iocpf timer start
bna: fix firmware loading on big-endian machines
bridge: fix br_multicast_query_expired() bug
via-rhine: Resigning as maintainer
brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
mac80211: Fix mac80211.h docbook comments
iwlwifi: nvm: fix otp parsing in 8000 hw family
iwlwifi: pcie: fix tracking of cmd_in_flight
ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
...
Pull Sparc fixes from David Miller:
1) Setup the core/threads/sockets bitmaps correctly so that 'lscpus'
and friends operate properly. Frtom Chris Hyser.
2) The bit that normally means "Cached Virtually" on sun4v systems,
actually changes meaning in M7 and later chips. Fix from Khalid
Aziz.
3) One some PCI-E systems we need to probe different OF properties to
fill in the PCI slot information properly, from Eric Snowberg.
4) Kill an extraneous memset after kzalloc(), from Christophe Jaillet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
sparc64: pci slots information is not populated in sysfs
sparc: kernel: GRPCI2: Remove a useless memset
sparc64: Setup sysfs to mark LDOM sockets, cores and threads correctly
This tweaks an exported user-space header to fix
build breakage for userspace using it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbKwGAAoJECgfDbjSjVRp8t0H/3H9RYIMZskzWFwLt3iguVsR
A6C+JNMszd4+SBlRYHJ1LyNOYh0xQN089VeHIqVp3agGX4ecOJ58LlUKb670XSFT
ItXY1QVwlR1cQ2HjYjllSijKy13W4zeDmnYdicsp0DmOngr3Jy1xw8b0LvhhUDEl
bhzJ4eLV9Cn0oxrirbHhvqi4ESNKa7avP7jbq/7r0qtgBSzdf6WSP7ZhCu+BdEwW
tpXBh9m3vriFGXmagn10pxsO8k8oDRGFPJPT2SQeyvbTZWkojHPY034PtbrFNpba
YT2/FCs8nvq7/fmz47nRdX6KivyeSF+RZrCumozjSWJntNolxu3EbHcnJbd0kmU=
=q1Wp
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fix from Michael Tsirkin:
"Last-minute virtio fix for 4.1
This tweaks an exported user-space header to fix build breakage for
userspace using it"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
include/uapi/linux/virtio_balloon.h: include linux/virtio_types.h
Scott Feldman says:
====================
rocker: enable by default untagged VLAN support
This patch set is a followup to Simon Horman's RFC patch:
[PATCH/RFC net-next] rocker: by default accept untagged packets
Now, on port probe, we install untagged VLAN (vid=0) support for each port
as the default. This is equivalent to the command:
bridge vlan add vid 0 dev DEV self
Accepting untagged VLAN pkts is a reasonable default, but the user could
override this with:
bridge vlan del vid 0 dev DEV self
With this, we no longer need 8021q module to install vid=0 when port interface
opens. In fact, we don't need support for legacy VLAN ndo ops at all since
they're superseded by bridge_setlink/dellink. So remove legacy VLAN ndo ops
support in driver. (The legacy VLAN ndo ops are supported by bonding/team
drivers, but don't fit into the transaction model offered by switchdev, so
switching all VLAN functions to bridge_setlink/dellink switchdev support gets
us stacked driver + transaction model support).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove support for legacy ndo ops
.ndo_vlan_rx_add_vid/.ndo_vlan_rx_kill_vid. Rocker will use
bridge_setlink/dellink exclusively for VLAN add/del operations.
The legacy ops are needed if using 8021q driver module to setup VLANs on
the port. But an alternative exists in using bridge_setlink/delink to
setup VLANs, which doesn't depend on 8021q module. So rocker will switch
to the newer setlink/dellink ops. VLANs can added/delete from the port,
regardless if port is bridged or not, using the bridge commands:
bridge vlan [add|del] vid VID dev DEV self
(Yes, I agree it's confusing to use the "bridge" command to set a VLAN on a
non-bridged port).
Using setlink/dellink over legacy ops let's us handle the stacked driver
case automatically. It's built-in. setlink also pass additional flags
(PVID, egress untagged) that aren't available with the legacy ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the port joins a bridge, the port's internal VLAN ID needs to change
to the bridge's internal VLAN ID. Likewise, when leaving the bridge, the
internal VLAN ID reverts back the port's original internal VLAN ID. (The
internal VLAN ID is used by device to internally mark untagged pkts with
some VLAN, which will eventually be removed on egress...think PVID). When
the internal VLAN ID changes, we need to update the VLAN table entries and
the router MAC entries for IP/IPv6 to reflect the new internal VLAN ID.
This patch makes use of the common rocker_port_vlan_add/del functions to
make sure the tables are updated for the current internal VLAN ID.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port probe, install by default untagged VLAN support. This is
equivalent to running the command:
bridge vlan add vid 0 dev DEV self
A user could, if they wanted, manaully removing untagged support from the
port by running the command:
bridge vlan del vid 0 dev DEV self
But installing it by default on port initialization gives the normal
expected behavior.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic house keeping: If there is an error adding the router MAC for this
vlan, removing the just installed VLAN table entry to leave device in same
state as before failure.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating the array of rocker port pointers, zero the array values so
we can test for !NULL to see if port is allocated/registered. We'll need
this later when installing untagged VLAN support for each port, during port
probe. It's a long story, but to install a VLAN (vid=0 for untagged, in
this case) on a port, we'll need to scan other ports to see if the VLAN
group for that VLAN has been setup. To scan the other ports, we need to
walk the port array.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fix for net
The following patch reverts the ebtables chunk that enforces counters that was
introduced in the recently applied d26e2c9ffa ('Revert "netfilter: ensure
number of counters is >0 in do_replace()"') since this breaks ebtables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused function cxgb4_enable_db_coalescing() and
cxgb4_disable_db_coalescing()
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker (switch) of a rocker_port may be trivially obtained from
the latter it seems cleaner not to pass the former to a function when
the latter is being passed anyway.
rocker_port_rx_proc() is omitted from this change as it is a hot path case.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently rely on the PMTU discovery of xfrm.
However if a packet is localy sent, the PMTU mechanism
of xfrm tries to to local socket notification what
might not work for applications like ping that don't
check for this. So add pmtu handling to vti6_xmit to
report MTU changes immediately.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver allocates one page for each buffer on the rx ring, which is
too much on architectures like ppc64 and can cause unexpected allocation
failures when the system is under stress. Now, we keep a memory pool
per queue, and if the architecture's PAGE_SIZE is greater than 4k, we
fragment pages and assign each 4k segment to a ring element, which
reduces the overall memory consumption on such architectures. This
helps avoiding errors like the example below:
[bnx2x_alloc_rx_sge:435(eth1)]Can't alloc sge
[c00000037ffeb900] [d000000075eddeb4] .bnx2x_alloc_rx_sge+0x44/0x200 [bnx2x]
[c00000037ffeb9b0] [d000000075ee0b34] .bnx2x_fill_frag_skb+0x1ac/0x460 [bnx2x]
[c00000037ffebac0] [d000000075ee11f0] .bnx2x_tpa_stop+0x160/0x2e8 [bnx2x]
[c00000037ffebb90] [d000000075ee1560] .bnx2x_rx_int+0x1e8/0xc30 [bnx2x]
[c00000037ffebcd0] [d000000075ee2084] .bnx2x_poll+0xdc/0x3d8 [bnx2x] (unreliable)
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new optional attribute OVS_USERSPACE_ATTR_ACTIONS is added to an
OVS_ACTION_ATTR_USERSPACE action, then include the datapath actions
in the upcall.
This Directly associates the sampled packet with the path it takes
through the virtual switch. Path information currently includes mangling,
encapsulation and decapsulation actions for tunneling protocols GRE,
VXLAN, Geneve, MPLS and QinQ, but this extension requires no further
changes to accommodate datapath actions that may be added in the
future.
Adding path information enhances visibility into complex virtual
networks.
Signed-off-by: Neil McKee <neil.mckee@inmon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we scan a packet for GRO processing, we want to see the most
common packet types in the front of the offload_base list.
So add a priority field so we can handle this properly.
IPv4/IPv6 get the highest priority with the implicit zero priority
field.
Next comes ethernet with a priority of 10, and then we have the MPLS
types with a priority of 15.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f96dee13b8.
It isn't right, ethtool is meant to manage one PHY instance
per netdevice at a time, and this is selected by the SET
command. Therefore by definition the GET command must only
return the settings for the configured and selected PHY.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dff173de84 ("bnx2x: Fix statistics locking scheme") changed the
bnx2x locking around statistics state into using a mutex - but the lock
is being accessed via a timer which is forbidden.
[If compiled with CONFIG_DEBUG_MUTEXES, logs show a warning about
accessing the mutex in interrupt context]
This moves the implementation into using a semaphore [with size '1']
instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_build_gops’:
drivers/net/xen-netback/netback.c:1253:8: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘int’ [-Wformat=]
(txreq.offset&~PAGE_MASK) + txreq.size);
^
PAGE_MASK's type can vary by arch, so a cast is needed.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
----
v2: Cast to unsigned long, since PAGE_MASK can vary by arch.
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This partially reverts commit 1086bbe97a ("netfilter: ensure number of
counters is >0 in do_replace()") in net/bridge/netfilter/ebtables.c.
Setting rules with ebtables does not work any more with 1086bbe97a place.
There is an error message and no rules set in the end.
e.g.
~# ebtables -t nat -A POSTROUTING --src 12:34:56:78:9a:bc -j DROP
Unable to update the kernel. Two possible causes:
1. Multiple ebtables programs were executing simultaneously. The ebtables
userspace tool doesn't by default support multiple ebtables programs
running
Reverting the ebtables part of 1086bbe97a makes this work again.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes userspace compilation error:
error: unknown type name ‘__virtio16’
__virtio16 tag;
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e, func, da;
@@
-init_timer (&e);
+setup_timer (&e, func, da);
-e.data = da;
-e.function = func;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
