drivers/net/s2io.c:7559: warning: ‘tcp_len’ may be used uninitialized in this function
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is a ptype handler holding a clone of this skb, whose
destination MAC addresse is overwritten, the owner of this handler may
get a corrupted packet.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are only used when net poll controller is enabled.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer requires multicast capability flag set during IFACE_CREATE
for adding multicast filters.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Lancer disable interrupts in close by disarming CQs and EQs.
Change the order of calls in be_close to achieve the correct result.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove TX Queue stop in close
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add error recovery during load for Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L4 checksum field is valid only for TCP/UDP packets in Lancer
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Workaround added for Lancer in handling RX ERR completion received
when no RX buffers are posted is not needed.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Subramanian Seetharaman <subbu.seetharaman@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc911x driver would drop frames longer than 1518 bytes, which is a
problem for networks with VLAN tagging. The VLAN1 tag register is used
to increase the legal frame size to 1522 when a VLAN tag is identified.
Signed-off-by: Göran Weinholt <weinholt@csbnet.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the p54spi Kconfig help text.
The driver works well on n8x0, so remove the words "experimental" and "untested".
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems ath5k has issues receiving broadcast packets (ARPs) when
using multiple STA interfaces associated with multiple APs.
This patch ensures the NIC is always in PROMISC mode if there
are more than 1 stations associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase resolution of MaxBW algorithm to suit
Min Bandwidth configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing speed setting in NPAR requires HW access, this patch
delays the access to D0 state when performed in D3.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report link to OS and other PFs after HW is fully reconfigured
according to new link parameters. (Affected only Multi Function modes).
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove port MAX BW configuration from non-pmf functions,
which caused reconfigure of HW according to 10G (fake) link.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes appletalk to use lock_sock instead of
lock_kernel for serialization. I tried to make sure
that we don't hold the socket lock during sleeping
functions, but I did not try to prove whether the
locks are necessary in the first place.
Compile-tested only.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: David Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
This allows "ethtool advertise" to control the speed and duplex
features the device offers the switch.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Usually H/W generate statistics notify once per about 100ms, but
sometimes we can receive notify in shorter time, even 2 ms.
This can be problem for plcp health and ack health checking.
I.e. with 2 plcp errors happens randomly in 2 ms duration, we
exceed plcp delta threshold equal to 100 (2*100/2).
Also checking ack's in short time, can results not necessary false
positive and firmware reset, for example when channel is noised and
we do not receive ACKs frames or when remote device does not send
ACKs at the moment.
Patch change code to do statistic check and possible recovery only
if 99ms elapsed from last check. Forced delay should assure we have
good statistic data to estimate hardware state.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make iwl_good_plcp_health code easiest to read.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put generic rx_handlers (except iwlagn_rx_reply_compressed_ba) to
iwl-rx.c . Make functions static and change prefix from iwlagn_ to
iwl_ . Beautify iwl_setup_rx_handlers and do some other minor coding
style changes.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No use printing addresses of pointers, just print the
pointers themselves.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that all accesses to the data_queue structures is done via the specialized
rt2x00queue_get_tx_queue function or via direct accesses, there is no
need for the rt2x00queue_get_queue function anymore, so remove it.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the spirit of optimizing the code to get the queue structure of TX queues,
also optimize the code to get beacon queues. We can simply use the bcn queue
field of the rt2x00_dev structure instead of using the rt2x00queue_get_queue
function.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ATIM queue is considered to be a TX queue by the drivers that support
the queue. Therefore include support for the ATIM queue to the
rt2x00queue_get_tx_queue function so that the drivers that support the ATIM
queue can also use that function.
Add the support in such a way that drivers that do not support the ATIM
queue are not penalized in their efficiency.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current code for the atim queue is strange, as it is considered in the
rt2x00_dev structure as a second beacon queue.
Normalize this by letting the atim queue have its own struct data_queue
pointer in the rt2x00_dev structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't use interrupt threads anymore. Fix the comment.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCI device irqmask is locked by a spin_lock. Currently
spin_lock_irqsave is used everywhere. To reduce the locking overhead
replace spin_lock_irqsave in hard irq context with spin_lock and in
soft irq context with spin_lock_irq.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up multiple BSSIDs in AP mode on an rt2800pci device we
previously used the STAs AID to select an appropriate key slot. But
since the AID is per VIF we can end up with two STAs having the same AID
and thus using the same key index. This resulted in one STA overwriting
the key information of another STA.
Fix this by simply searching for the next unused entry in the pairwise
key table.
Also bring the key table init in sync with deleting keys by initializing
the key table entries to 0 instead of 1.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the code less error-prone.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_tx_rate is not valid for HT rates. Hence, restructure the
TX desciptor creation to be aware of MCS rates. The generic TX desciptor
creation now cares about the rate_mode (CCK, OFDM, MCS, GF).
As a result, ieee80211_get_tx_rate gets only called for legacy rates.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ifs" is only used by no-HT devices. Move it into the plcp substruct and
fill in the value only for no-HT devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some fields only need to be u8 and for ifs and txop we can use the
already available enums.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT and no-HT rt2x00 devices use a partly different TX descriptor.
Optimize the tx desciptor memory layout by putting the PLCP and HT
substructs into a union and introduce a new driver flag to decide which
TX desciptor format is used by the device.
This saves us the expensive PLCP calculation fOr HT devices and the HT
descriptor setup on no-HT devices.
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices like rt2800* own a hardware sequence counter and thus
don't need to use a software sequence counter at all. Add a new driver
flag to shortcut the software sequence number generation on devices that
don't need it.
rt61pci, rt73usb and rt2800* seem to make use of a hw sequence counter
while rt2400pci and rt2500* need to do it in software.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00queue_write_tx_frame is unlikely to fail. Tell the compiler.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This special case shouldn't happen very often. Only if a frame that
is not intended to be aggregated ends up in an AMPDU _and_ was intended
to be sent at a different MCS rate as the aggregate. Hence, using
unlikely is justified.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since tx_info->control.vif was already accessed before it cant't be NULL
here.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These conditions are unlikely to happen, tell the compiler.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases (tx path for example) we don't need to check for non-tx
queues in rt2x00queue_get_queue. Hence, introduce a new method
rt2x00queue_get_tx_queue that is only valid for tx queues and use it in
places where only tx queues are valid.
Furthermore, this new method is quite short and as such can be inlined
to avoid the function call overhead.
This only converts the txdone functions of drivers that don't use an ATIM
queue and the generic tx path.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800 specific code contains a lots of whitespace damage caused by
the commit 'rt2x00: Add support for RT5390 chip'.
This patch fixes those whitespace errors.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
/<debugfs_root>/ieee80211/phyX/ath9k/regdump is the interface
to dump the registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver for the RTL8187L chips returns IEEE80211_TX_STAT_ACK for all
packets, even if the maximum number of retries was exhausted. In addition
it fails to setup max_rates in the ieee80211_hw struct, This behavior
may be responsible for the problems noted in Bug 14168. As the bug is very
old, testers have not been found, and I do not have the case where the
indicated signal is less than -70 dBm.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on work by Neil Turton <nturton@solarflare.com> and
Kieran Mansley <kmansley@solarflare.com>.
The BIU has now been verified to handle 3- and 4-dword writes within a
single 128-bit register correctly. This means we can enable write-
combining and only insert write barriers between writes to distinct
registers.
This has been observed to save about 0.5 us when pushing a TX
descriptor to an empty TX queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add pr_fmt.
Removed trailing "\n" from version,
add back via pr_info("%s\n", version);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bit more data to the output.
Convert string speeds to integer.
Object size reduced a tiny bit.
$ size drivers/net/mii.o*
text data bss dec hex filename
4155 56 1000 5211 145b drivers/net/mii.o.new
4184 56 1000 5240 1478 drivers/net/mii.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current logging styles.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neatening and standardization to the current logging mechanisms.
Miscellaneous speen/speed typo correction.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it isn't necessary nor really useful any longer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend be_alloc_pages() with a gfp parameter, so that we use GFP_KERNEL
allocations instead of GFP_ATOMIC when not running in softirq context.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current logging forms with pr_fmt.
Convert DBG macro to tun_debug, use netdev_printk as well.
Add printf verification when TUN_DEBUG not defined.
Miscellaneous comment typo fix.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FTMAC100 Ethernet Media Access Controller supports 10/100 Mbps and
MII. This driver has been working on some ARM/NDS32 SoC's including
Faraday A320 and Andes AG101.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The temperature reported by 'cat /sys/class/net/wlan?/device/temperature'
is incorrect for devices with BT capability. Report the value from the
correct statistics structure. Tested with 130, 100, 6205 and 5300.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlagn: Support new 1000 microcode.
New iwlwifi-1000 microcode requires driver support for API version 5.
(There is no version 4)
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Set the gf_protection bit when calling ACX_HT_BSS_OPERATION according
to the GF bit passed by mac80211 in ht_operation_mode.
[Added a proper commit message -- Luca]
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Commands are sometimes sent to FW on scan completion. Make sure the chip
is awake to receive them. Sending commands while the chip is in ELP
can cause SDIO read errors and/or crash the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Tests have shown that the requested number of memory blocks is
sub-optimal. Slightly modify the requested number of memory blocks for
TX.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
TX might be handled in the threaded IRQ handler, in which case, TX work
might be scheduled just to discover it has nothing to do.
Save a few context switches by cancelling redundant TX work in case TX
is about to be handled in the threaded IRQ handler. Also, avoid
scheduling TX work from wl1271_op_tx if not needed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interrupt of the wl12xx is a level interrupt in nature, since the
interrupt line is not auto-reset. However, since resetting the interrupt
requires bus transactions, this cannot be done from an interrupt
context. Thus, requesting a level interrupt would require to disable the
irq and re-enable it after the HW is acknowledged. Since we now request
a threaded irq, this can also be done by specifying the IRQF_ONESHOT
flag.
Triggering on an edge can be problematic in some platforms, if the
sampling frequency is not sufficient for detecting very frequent
interrupts. In case an interrupt is missed, the driver will hang as the
interrupt line will stay high until it is acknowledged by the driver,
which will never happen.
Fix this by requesting a level triggered interrupt, with the
IRQF_ONESHOT flag.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
To achieve maximal throughput, it is very important to react to
interrupts as soon as possible. Currently the interrupt handler wakes up
a worker for handling interrupts in process context. A cleaner and more
efficient design would be to request a threaded interrupt handler. This
handler's priority is very high, and can do blocking operations such as
SDIO/SPI transactions.
Some work can be deferred, mostly calls to mac80211 APIs
(ieee80211_rx_ni and ieee80211_tx_status). By deferring such work to a
different worker, we can keep the irq handler thread more I/O
responsive. In addition, on multi-core systems the two threads can be
scheduled on different cores, which will improve overall performance.
The use of WL1271_FLAG_IRQ_PENDING & WL1271_FLAG_IRQ_RUNNING was
changed. For simplicity, always query the FW for more pending
interrupts. Since there are relatively long bursts of interrupts, the
extra FW status read overhead is negligible. In addition, this enables
registering the IRQ handler with the ONESHOT option.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The SDIO bus is claimed and released for each SDIO transaction. In
addition to the few CPU cycles it takes to claim and release the bus, it
may also cause undesired side effects such as the MMC host stopping its
internal clocks.
Since only the wl12xx_sdio driver drives this SDIO card, it is safe to
claim the SDIO host once (on power on), and release it only when turning
the power off.
This patch was inspired by Juuso Oikarinen's (juuso.oikarinen@nokia.com)
patch "wl12xx: Change claiming of the (SDIO) bus".
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On newer hardware revisions, there is no need to write the host's
counter at the end of a RX transaction. The same applies to writing the
number of packets at the end of a TX transaction.
It is generally a good idea to avoid unnecessary SDIO/SPI transfers.
Throughput and CPU usage are improved when avoiding these.
Send the host's RX counter and the TX packet count only if needed, based
on the hardware revision.
[Changed WL12XX_QUIRK_END_OF_TRANSACTION to use BIT(0) -- Luca]
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW has a limited amount of memory for holding frames. In case it
runs out of memory reserved for RX frames, it'll have no other choice
but to drop packets received from the AP. Thus, it is important to
handle RX data interrupts as soon as possible, before handling anything
else.
In addition, since there are enough TX descriptors to go around, it is
better to first send TX frames, and only then handle TX completions.
Fix this by changing the order of function calls in wl1271_irq_work.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames in the tx_frames array include extra private headers, which must
be removed before passing the skbs to ieee80211_tx_status.
Fix this by removing any private headers in wl1271_tx_reset, similar to
how this is done in wl1271_tx_complete_packet.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Runtime PM might not always be enabled. Even if it is enabled in the
running kernel, it can still be temporarily disabled, for instance
during suspend. Runtime PM is opportunistic in nature, and should not be
relied on for toggling power.
In case the interface is removed and re-added while runtime PM is
disabled, the FW will fail to boot, as it is mandatory to toggle power
between boots. For instance, this can happen during suspend in case one
of the devices fails to suspend before the MMC host suspends, but after
mac80211 was suspended. The interface will be removed and reactivated
without toggling the power.
Fix this by calling mmc_power_save_host/mmc_power_restore_host in
wl1271_sdio_power_on/off functions. It will toggle the power to the chip
even if runtime PM is disabled. The runtime PM functions should still be
called to make sure runtime PM does not opportunistically power the chip
off (e.g. after resuming from system suspend).
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In the linux-firmware git tree, the firmwares and the NVS are inside
the ti-connectivity directory. Fix the filenames that the driver
looks for accordingly.
[Fixed commit message and merged with the latest changes. -- Luca]
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Updating the copyrights for 2011 as well as make the ixgbe_copyright string
a constant.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 devices grabs semaphores differently than 82599 and 82598
devices do. They do however also grab them in allot of the same
functions. So I'm adding a new MAC operation function pointer to
allow us to use the correct function based on our MAC type. I'm also
changing all the semaphore calls to use this new function pointer.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up commented out include file and use #define instead of hard coded
value for number of RAR entries.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I2C interface was not being correctly locked down per port. As such
this can lead to race conditions that can cause issues. This patch cleans
up the handling to make certain we are not experiencing racy I2C access.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were reading the address after it had been initialized and this results
in the permanent address on the system being changed. This change corrects
that by storing the address before we re-initialize it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains a number of whitespace and formatting cleanups.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch specifically checks for 100 Full link speed instead of
assuming we are linked at 100 if not linked at 10G and 1G.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the unused code that was setting up the uc_addr_list.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change modifies the ixgbe drivers so that it will not drop the
multicast filters while updating them. Instead it uses an intermediate
table to store the filter and then writes that filter to the hardware.
Based on original patch from Dave Boutcher <daveboutcher@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Dave Boutcher <daveboutcher@gmail.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 PHY reset pointer isn't currently used which is a good thing as it
wouldn't work as implemented. On top of that the X540 firmware is written
with the assumption that is does not need to be reset for proper
initialization so it's not needed. I'm just assigning the pointer at NULL
as the current implementation is rather misleading.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that out of bounds requests to these calls will
now return IXGBE_ERR_INVALID_ARGUMENT instead of returning 0.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fills in the values for bus speed and width of the
ixgbe_bus_speed and ixgbe_bus_width enums.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some PHYs require that we poll the reset bit and wait for it to clear
before continuing initialization. As such we should add this check to the
end of the ixgbe_reset_phy_generic routine.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently check link reports the link state as down, if at any time
the link had previously gone down since the last time the LINKS
register was read. This does not accurately reflect the function of
the check link call, which should be to return the CURRENT link
state. Code now reads the LINKS registers twice, once to clear the
previous and again to get the current value.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up several issues in ixgbe_identify_sfp_module_generic
including whitespace, redundant code, I2C EEPROM reads without exception
handling, and an if/elseif/else without braces.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double resets are required for recovery from certain error conditions.
Between resets, it is necessary to stall to allow time for any pending HW
events to complete. We use 1usec since that is what is needed for
ixgbe_disable_pcie_master(). The second reset then clears out any effects
of those events.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The media type was not being set for the 82599 T3 LAN on motherboard. This
change corrects that.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly freeing IRQs that we had not requested. This change
corrects that by making certain we only free q_vectors that we have
requested IRQs for.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up much of the logic related to the hardware semaphores
on the adapters. There were a number of issues with timings that needed to
be addressed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change just cleans up a few defines in ixgbe_type.h related to wake on LAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix Compiler warnings of variables that are initialized but not used.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix changes the remaining calls to strncpy that have not yet
been changed to use the "sizeof(buf) - 1" syntax rather than just
a number for buffer size.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes the reg_pattern_test so that the test does not fail
on i350 parts.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there's no warning printed when max_vfs > 7 is specified with
igb and the maximum of 7 is silently enforced. This patch prints a
warning and informs the user of the actions taken.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- Remove the dependency of cxgb4 and cxgb4vf on INET. cxgb3 really
depends on INET, keep it but add it directly to the driver's Kconfig
entry.
- Make the iSCSI drivers cxgb3i and cxgb4i available in the SCSI menu
without requiring any options in the net driver menu to be enabled
first. Add needed selects so the iSCSI drivers can build their
corresponding net drivers.
- Remove CHELSIO_T*_DEPENDS.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We service 2 queues (kcq1 and kcq2) in cnic_service_bnx2x_bh(). If
the status block index has changed when servicing the kcq2, we must
go back and check kcq1. The latest status block index will be used
to acknowledge the interrupt, and without looping back to check kcq1,
we may miss events on kcq1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status block index is used to acknowledge interrupt events and must
be read before checking for the interrupt events, so we need to add rmb()
to guarantee that.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for 82577/82578 was added[1] in 2.6.31, PHY wakeup was in-
advertently enabled (even though it does not function properly) on ICH10
LOMs. This patch makes it so that the ICH10 LOMs use MAC wakeup instead
as was done with the initial support for those devices (i.e. 82567LM-3,
82567LF-3 and 82567V-4).
[1] commit a4f58f5455
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: <stable@kernel.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse complains because the e1000 driver is calling ioread on a pointer
not tagged as __iomem.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It now takes an additional argument so it can be used to
flush-and-invalidate pages that are cached using hash-for-home
as well those that are cached with coherence point on a single cpu.
This allows it to be used more widely for changing the coherence
point of arbitrary pages when necessary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This finally makes TX on OFDM rates possible on my dev with PHY rev 4.
We still have lower performance than wl, but at least speeds around 15M
become possible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AID and BSSID should be set in the HW only for the
first station interface or adhoc interface. Also, cancel
the ANI timer in stop() for multi-STA scenario. And finally
configure the HW beacon timers only for the first station
interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- adjust code of rtl8169_set_speed_xmii function
- remove parts of code which are done in rtl_pll_power_up
function (8168 only)
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
All features originally planned for version 3.1 (and some that
weren't) have been implemented.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In Falcon we can configure the fill levels of the RX data FIFO which
trigger the generation of pause frames (if enabled), and we have
module parameters for this.
Siena does not allow the levels to be configured (or, if it does, this
is done by the MC firmware and is not configurable by drivers).
So far as I can tell, the module parameters are not used by our
internal scripts and have not been documented (with the exception of
the short parameter descriptions). Therefore, remove them and always
initialise Falcon with the default values.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This field does not exist in all MMDs we want to check, and all
callers allow it to be set (fault_fatal = 0).
Remove the loopback condition, as STAT2.DEVPRST should be valid
regardless of any fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We currently make no use of siena_nic_data::fw_{version,build} except
to format the firmware version for ethtool_get_drvinfo(). Since we
only read the version at start of day, this information is incorrect
after an MC firmware update. Remove the cached version information
and read it via MCDI whenever it is requested.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Instead calculate the KVA of receive data. It's not like it's a hard sum.
[bwh: Fixed to work with GRO.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Clearly it should be the size of ->ip_dst here.
Although this is harmless, but it still reads odd.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an additional check in the Davinci EMAC RX Handler,
which tests the __LINK_STATE_NOCARRIER flag along with the
__LINK_STATE_START flag as part EMAC shutting down procedure.
This avoids
WARNING: at drivers/net/davinci_emac.c:1040 emac_rx_handler+0xf8/0x120()
during rtcwake used to suspend the target for a specified duration.
Signed-off-by: Hegde, Vinay <vinay.hegde@ti.com>
Acked-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix FW initialization according to max BW stored in percents
for NPAR mode. Protect HW from being configured to speed 0.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a port profile disassociate all address registrations for the interface
are blown away from the adapter. This patch resets the driver cache of
registered address lists to zero after a port profile disassociate.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow randomised ethernet address if the device does not have a valid
EEPROM or pre-set MAC address.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary annotations about pointer to io memory space
that is checked by sparse.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix use of zero where NULL expected. And wrap long line.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so it wasn't
converted by commit 44c10138fd (PCI: Change all
drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
platform_set_drvdata() was used with argument of incorrect type and
could cause memory corruption. Moreover, because of not setting drvdata
in the correct place not all resources were freed upon module unload.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71d6429 (Driver core: convert platform_{get,set}_drvdata to
static inline functions) now triggers a warning in the macb network
driver:
CC drivers/net/macb.o
drivers/net/macb.c: In function ‘macb_mii_init’:
drivers/net/macb.c:263: warning: passing argument 1 of ‘platform_set_drvdata’ from incompatible pointer type
include/linux/platform_device.h:138: note: expected ‘struct platform_device *’ but argument is of type ‘struct net_device *’
Use dev_set_drvdata() on the device embedded in the net_device instead.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the bnx2x uses the generic dcbnl application tlv list
instead of implementing its own get-app handler. When the driver is
alerted to a change in the DCB negotiated parameters, it calls
dcb_setapp to update the dcbnl application tlvs list making it available
to user mode applications and registered notifiers.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just found that the controller hardware name is not set for the Softing
driver. After this patch, "$ ip -d link show" looks nicer.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
fmvj18x_cs:add new id
Toshiba lan&modem multifuction card (model name:IPC5010A)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several more network drivers that read the device's revision ID
from the PCI configuration register were merged after the commit
44c10138fd (PCI: Change all drivers
to use pci_device->revision), so it's time to do another pass of
conversion to using the 'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have separate iwl-agn-rx.c file after iwlegacy
split.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove check_plcp_health and check_ack_health ops methods, they are
unneeded after iwlegacy driver split. Merge check health code into to
iwl-rx.c and make functions static.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add module ack_check, and plcp_check parameters. Ack_check is disabled
by default since is proved that check ack health can cause troubles.
Plcp_check is enabled by default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible dma mappings and skbs introduced by commit
470058e0ad "iwlwifi: avoid Tx queue
memory allocation in interface down".
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit commit 470058e0ad
"iwlwifi: avoid Tx queue memory allocation in interface down" we do
not unmap dma and free skbs when down device and there is pending
transfer. What in consequence may cause that system hung (waiting
for free skb's) when performing shutdown at iptables module unload.
DMA leak manifest itself following warning:
WARNING: at lib/dma-debug.c:689 dma_debug_device_change+0x15a/0x1b0()
Hardware name: HP xw8600 Workstation
pci 0000:80:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=240]
Modules linked in: iwlagn(-) aes_x86_64 aes_generic fuse cpufreq_ondemand acpi_cpufreq freq_table mperf xt_physdev ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ext3 jbd dm_mirror dm_region_hash dm_log dm_mod uinput hp_wmi sparse_keymap sg wmi microcode serio_raw tg3 arc4 ecb shpchp mac80211 cfg80211 rfkill ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif firewire_ohci firewire_core crc_itu_t mptsas mptscsih mptbase scsi_transport_sas pata_acpi ata_generic ata_piix ahci libahci floppy nouveau ttm drm_kms_helper drm i2c_algo_bit i2c_core video [last unloaded: iwlagn]
Pid: 9131, comm: rmmod Tainted: G W 2.6.38-rc6-wl+ #33
Call Trace:
[<ffffffff810649ef>] ? warn_slowpath_common+0x7f/0xc0
[<ffffffff81064ae6>] ? warn_slowpath_fmt+0x46/0x50
[<ffffffff812320ab>] ? dma_debug_device_change+0xdb/0x1b0
[<ffffffff8123212a>] ? dma_debug_device_change+0x15a/0x1b0
[<ffffffff8149dc18>] ? notifier_call_chain+0x58/0xb0
[<ffffffff8108e370>] ? __blocking_notifier_call_chain+0x60/0x90
[<ffffffff8108e3b6>] ? blocking_notifier_call_chain+0x16/0x20
[<ffffffff812f570c>] ? __device_release_driver+0xbc/0xe0
[<ffffffff812f5808>] ? driver_detach+0xd8/0xe0
[<ffffffff812f45d1>] ? bus_remove_driver+0x91/0x100
[<ffffffff812f6022>] ? driver_unregister+0x62/0xa0
[<ffffffff8123d5d4>] ? pci_unregister_driver+0x44/0xa0
[<ffffffffa05632d1>] ? iwl_exit+0x15/0x1c [iwlagn]
[<ffffffff810ab492>] ? sys_delete_module+0x1a2/0x270
[<ffffffff81498da9>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff8100bf42>] ? system_call_fastpath+0x16/0x1b
I still can observe above warning after apply patch, but it is very
hard to reproduce it, and have count=1. Whereas that one is easy to
reproduce using debugfs force_reset while transmitting data, and have
very big counts eg. 240, like quoted here. So count=1 WARNING seems
to be different issue that need to be resolved separately.
v1 -> v2: fix infinity loop bug I made during "for" to "while" loop transition.
v2 -> v3: remove unneeded EXPORT_SYMBOL
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually
used for this.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the RSSI calibration table was not found or not parsed properly,
priv->rssi_db will be NULL, p54_rssi_find needs to be able to deal
with that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c: In function ‘rtl92ce_rx_query_desc’:
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:255:5: warning: ‘rf_rx_num’ may be used uninitialized in this function
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:257:12: warning: ‘total_rssi’ may be used uninitialized in this function
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:466:6: warning: ‘weighting’ may be used uninitialized in this function
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rate_mask is initialized again later so this can be removed. Btw, if
rate_control_send_low(sta, priv_sta, txrc) returns false, that means
that "sta" is non-NULL. That's why the second initialization of
rate_mask is a little simpler than the first.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Mark Davis
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/at76c50x-usb.o
drivers/net/wireless/at76c50x-usb.c: In function ‘at76_mac80211_tx’:
drivers/net/wireless/at76c50x-usb.c:1759:4: warning: ‘return’ with a value, in function returning void
This is fallout from commit 7bb4568372
("mac80211: make tx() operation return void").
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stream length/tag fields have to be in little endian
format. Fixing this makes the driver work on big-endian
platforms.
Cc: stable@kernel.org
Tested-by: raghunathan.kailasanathan@wipro.com
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts bonding to use rx_handler. Results in cleaner
__netif_receive_skb() with much less exceptions needed. Also
bond-specific work is moved into bond code.
Did performance test using pktgen and counting incoming packets by
iptables. No regression noted.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
V4: rebase to net-next-2.6
This patch removes the flag IFF_IN_NETPOLL, we don't need it any more since
we have netpoll_tx_running() now.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
V4: rebase to net-next-2.6
V3: remove an useless #ifdef.
This patch unifies the netpoll code in bonding with netpoll code in bridge,
thanks to Herbert that code is much cleaner now.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/iwlegacy/built-in.o:(.rodata+0x29f0): multiple definition of `iwl_rates'
drivers/net/wireless/iwlwifi/built-in.o:(.rodata+0xa68): first defined here
powerpc64-linux-ld: Warning: size of symbol `iwl_rates' changed from 143 in drivers/net/wireless/iwlwifi/built-in.o to 130 in drivers/net/wireless/iwlegacy/built-in.o
drivers/net/wireless/iwlegacy/built-in.o:(.data+0x0): multiple definition of `bt_coex_active'
drivers/net/wireless/iwlwifi/built-in.o:(.data+0x668): first defined here
drivers/net/wireless/iwlegacy/built-in.o:(.rodata+0x750): multiple definition of `iwl_eeprom_band_1'
drivers/net/wireless/iwlwifi/built-in.o:(.rodata+0x27d0): first defined here
drivers/net/wireless/iwlegacy/built-in.o:(.rodata+0x3f0): multiple definition of `iwl_bcast_addr'
drivers/net/wireless/iwlwifi/built-in.o:(.rodata+0x24f8): first defined here
drivers/net/wireless/iwlegacy/built-in.o:(.bss+0x3d48): multiple definition of `iwl_debug_level'
drivers/net/wireless/iwlwifi/built-in.o:(.bss+0x21950): first defined here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize txq to avoid this warning:
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’:
drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pll_work should be cancelled on full_sleep or it may cause
redundant chip reset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes tramissing on OFDM rates for PHYs 1 and 2. There is
still something wrong with PHYs 3+. Tests has shown decreasing of
performance on CCK rates by 1-2%, we have to live with that.
Additionaly this noticeably reduces amount of PHY errors. They were
mostly produced by auto-switching to higher rate for better
performanced, which resulted in no transmit at all and PHY errors.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function was intended to calculate the
number of RX chains needed, but could only
work where the AP's streams were asymmetric,
i.e. 2 TX and 3 RX or similar. In the case
where IEEE80211_HT_MCS_TX_RX_DIFF was not
set, this function would calculate the wrong
information.
Additionally, mac80211 didn't pass through
the required values at all, so it couldn't
work anyway.
Rewrite the logic in this function and add
appropriate comments to make it readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the frequency can not be mapped to a channel structure log it and drop it.
Signed-off-by: Joseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Same fix as f844a709a7
"iwlwifi: do not set tx power when channel is changing".
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback sets slot time as specified in IEEE 802.11-2007
section 17.3.8.6 and raises round trip delay accordingly.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4320a breaks when enabling power save (bug 29732). So disable power save
for anything but BCM4320b that is known to work.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"AirLive X.USB now works perfectly under a Linux
environment!"
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4df3071ebd "ath9k_hw: optimize
interrupt mask changes", changed ath9k_hw_set_interrupts function to
enable interrupts regardless of function argument, what could possibly
be wrong. Correct that behaviour and check "ints" arguments before
enabling interrupts, also disable interrupts if ints do not have
ATH9K_INT_GLOBAL flag set.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The API for network devices has changed so that setting carrier off at
probe is no longer required. This should fix the IPv6 addrconf issue.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=29612
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: George Billios <gbillios@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On my G5 this fails to compile with
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:701: error: __ksymtab__rtl92c_phy_txpwr_idx_to_dbm causes a section type conflict
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:701: error: __ksymtab__rtl92c_phy_txpwr_idx_to_dbm causes a section type conflict
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:677: error: __ksymtab__rtl92c_phy_dbm_to_txpwr_Idx causes a section type conflict
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:677: error: __ksymtab__rtl92c_phy_dbm_to_txpwr_Idx causes a section type conflict
since you can't export static functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved all PCI_DEVICE_ID_NX2_57712(E) definitions to pci_ids.h
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This will synchronize the version with the out of tree driver which
shares its functionality.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
