At Android ADB and MTP use case, it uses f_fs which supports scatter list,
it means one request may need several TRBs for it. Besides, TRB consumes
very fast compared to TRB has prepared for above use case, there are at
most 120 pending requests, the date size is 16KB for each request, so four
TRBs (4KB per TRB) per sg entry at worst case. so we need to enlarge the
TRB ring length to avoid "no free TRB error". Since each TRB only consumes
12 bytes (3 * 32 bits), we enlarge the TRB length to 600, it leaves some
buffers for potential "no free TRB error", and only increases a little
memory cost.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The scatter buffer list support earlier than DEV_VER_V2 is not
good enough, software can't know well about short transfer for it.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add sg case for workaround 2, the workaround 2 is described at the
beginning of this file.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Judge each TRB has been handled at cdns3_trb_handled, since
the DMA pointer may be at the middle of the TD, we can't consider
this TD has finished at that time.
- Calculate req->actual according to finished TRBs.
- Handle short transfer for sg list use case correctly. When the
short transfer occurs, we check OUT_SMM at TRB to see if it is
the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For sg buffer list use case, we need to add ISP for each TRB, and
add CHAIN bit for each TRB except for the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It only dumps the first TRB per request, it is not useful if only dump
the first TRB when there are several TRBs per request. We improve it by
dumpping all TRBs per request in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It needs to use request->num_mapped_sgs to indicate mapped sg number,
the request->num_sgs is the sg number before the mapping. These two
entries have different values for the platforms which iommu or
swiotlb is used. Besides, it needs to use correct sg APIs for
mapped sg list for TRB assignment.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If cdns3_gadget_start is failed, it never frees cdns3_device structure.
Meanwhile, there is no release function for gadget device, it causes
there is no sync with driver core.
To fix this, we add release function for gadget device, and free
cdns3_device structure at there. Meanwhile, With the new UDC core
APIs, we could work with driver core better to handle memory leak
issue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After commit f4cfe5ce60 ("usb: cdns3: gadget: improve the
set_configuration handling"), the software will inform the
hardware the request has finished at cdns3_ep0_complete_setup.
The configuration set bit is only set after request has finished,
so it needs to move waiting operation after that. Meanwhile,
if it is timeout, it will show warning message and return error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some PHYs may need to enter related mode, and do some settings.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is meaningless to handle any interrupts after disconnecting
with host
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Below is the recommendation from Cadence designer:
Using this bit to be sure that PHY clock is keeping up in active
state. It's good to keep Fast Access bit enabled as long as there
is any access to USB register.
It is used to fix the potential ARM core hang when visit controller
register after DEVDS (.pullup is cleared) is set, the threaded irq
may be scheduled at that time.
Cc: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the board uses role switch class for switching the role, it should
not depends on SoC OTG hardware siginal any more, so quit early.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of
Receiver during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail condition
is detected to work around the above issue. This feature is
disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we rely on a DT property do decide when to
apply the workaround.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since we have both USB2 and USB3 PHYs for cdns3 controller, it is
better we have unity APIs to handle both USB2 and USB3's power, it
could simplify code for error handling and further power management
implementation.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch split function cdns3_drd_switch_gadget and
cdns3_drd_switch_host into:
- cdns3_drd_host_on
- cdns3_drd_host_off
- cdns3_drd_gadget_on
- cdns3_drd_gadgett_off
These functions don't have any shared code so it's better to
have smaller, faster and easier functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some error code can be preserved, so we can remove overwriting
error code returned by some functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch adds 2 definitions that make it easier to understand the code.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch changes return type from int to bool for
cdns3_is_host and cdns3_is_device functions.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
IRQ_NONE can be returned indirect.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch remove some variables initialization from core.c and drd.c
file.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Function is not used in driver so it can be removed.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It doesn't need to enable/disable L1 on the fly for EP0 transfer,
we only need to enable L1 after SET_CONFIGURATION.
This code may be introduced by careless.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Delete the duplicated EP_CMD_ERDY and EP_CMD_REQ_CMPL setting
- Prepare the next setup before setting EP_CMD_ERDY and EP_CMD_REQ_CMPL,
it could avoid a bug that DMA hang at EP0 OUT for DEV_VER_NXP_V1
- Delete the duplicated cdns3_set_hw_configuration calling at
cdns3_req_ep0_set_configuration, the composite.c will handle
this request, and call .ep0_queue back, and at .ep_queue it will
call cdns3_set_hw_configuration.
- Move cdns3_allow_enable_l1 into cdns3_set_hw_configuration since
it is part of this function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719160910.60018-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
'zlp' was documented, but in the wrong place.
Fixes the following W=1 kernel build warning(s):
drivers/usb/cdns3/ep0.c:36: warning: Function parameter or member 'zlp' not described in 'cdns3_ep0_run_transfer'
drivers/usb/cdns3/ep0.c:705: warning: Excess function parameter 'zlp' description in 'cdns3_gadget_ep0_queue'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-23-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mainline misspelled function argument descriptions. Also one
formatting issue with a missing '@' identifier.
Fixes the following W=1 build warnings:
drivers/usb/cdns3/gadget.c:653: warning: Function parameter or member 'priv_ep' not described in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:653: warning: Excess function parameter 'priv_dev' description in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:1088: warning: Function parameter or member 'request' not described in 'cdns3_ep_run_transfer'
drivers/usb/cdns3/gadget.c:2574: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2574: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2898: warning: Function parameter or member 'priv_dev' not described in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:2898: warning: Excess function parameter 'cdns3' description in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:3210: warning: Function parameter or member 'cdns' not described in 'cdns3_gadget_init'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-18-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add some missing function argument descriptions for 'ep', 'desc'
and 'zlp', and correct spelling/bitrot issues surrounding the
correct spelling of present args.
Fixes the following W=1 warnings:
drivers/usb/cdns3/ep0.c:36: warning: Function parameter or member 'zlp' not described in 'cdns3_ep0_run_transfer'
drivers/usb/cdns3/ep0.c:236: warning: Function parameter or member 'ctrl' not described in 'cdns3_req_ep0_get_status'
drivers/usb/cdns3/ep0.c:236: warning: Excess function parameter 'ctrl_req' description in 'cdns3_req_ep0_get_status'
drivers/usb/cdns3/ep0.c:411: warning: Function parameter or member 'ctrl' not described in 'cdns3_req_ep0_handle_feature'
drivers/usb/cdns3/ep0.c:411: warning: Excess function parameter 'ctrl_req' description in 'cdns3_req_ep0_handle_feature'
drivers/usb/cdns3/ep0.c:661: warning: Function parameter or member 'ep' not described in 'cdns3_gadget_ep0_enable'
drivers/usb/cdns3/ep0.c:661: warning: Function parameter or member 'desc' not described in 'cdns3_gadget_ep0_enable'
drivers/usb/cdns3/ep0.c:671: warning: Function parameter or member 'ep' not described in 'cdns3_gadget_ep0_disable'
drivers/usb/cdns3/ep0.c:867: warning: Function parameter or member 'priv_ep' not described in 'cdns3_init_ep0'
drivers/usb/cdns3/ep0.c:867: warning: Excess function parameter 'ep_priv' description in 'cdns3_init_ep0'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 3 misspellings and 1 incorrect format used in this file's
kerneldoc function headers. Fixing them squashes the following W=1
kernel build warnings:
drivers/usb/cdns3/gadget.c:653: warning: Function parameter or member 'priv_ep' not described in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:653: warning: Excess function parameter 'priv_dev' description in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:1088: warning: Function parameter or member 'request' not described in 'cdns3_ep_run_transfer'
drivers/usb/cdns3/gadget.c:2574: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2574: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2898: warning: Function parameter or member 'priv_dev' not described in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:2898: warning: Excess function parameter 'cdns3' description in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:3210: warning: Function parameter or member 'cdns' not described in 'cdns3_gadget_init'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-14-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If it is 'int', it can't stands for the highest bit for 32-bit
number, since the largest 'int' is 0x7fffffff.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported by Coverity scan, and fixed it by declare the reg as
unsigned long.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value '0' is duplicated with USB_DIR_OUT
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'tmode' is ctrl->wIndex, changing it as the real test
mode value for register assignment.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the TEST_ defines in the usb/ch9.h files did not have
the USB_ prefix on it, making it a bit confusing when reading the file,
as well as not the nicest thing to do in a uapi file.
So fix that up and add the USB_ prefix on to them, and fix up all
in-kernel usages. This included deleting the duplicate copy in the
net2272.h file.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jules Irenge <jbi.octave@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: Rob Gill <rrobgill@protonmail.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Bin Liu <b-liu@ti.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
