Configure busturnaround, cycle2cycledelay, waitmonitoringtime,
clkactivationtime in gpmc_cs_set_timings(). This is done so
that boards can configure these parameters of gpmc in Kernel
instead of relying on bootloader. Also configure bool type
timings like extradelay.
This needed change to the existing users that were configuring
clk activation time and extra delay by directly writing to
registers. Thanks to Tony for making me aware of users of clk
activation and being kind enough to test the modified one.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Requirement of gpmc header outside of mach-omap2 has been
cutoff, move gpmc header file in plat-omap folder to local
mach-omap2 folder
Objective - common zImage participation of omap
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resolve some warnings identified by cppcheck in arch/arm/mach-omap2:
[arch/arm/mach-omap2/usb-tusb6010.c:129]: (style) Checking if unsigned variable 'tmp' is less than zero.
[arch/arm/mach-omap2/prm_common.c:241]: (error) Possible null pointer dereference: irq_setup - otherwise it is redundant to check if irq_setup is null at line 247
[arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'per_clkdm' is assigned a value that is never used
[arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'core_clkdm' is assigned a value that is never used
[arch/arm/mach-omap2/pm24xx.c:185]: (style) Variable 'only_idle' is assigned a value that is never used
[arch/arm/mach-omap2/mux.c:254]: (error) Possible null pointer dereference: mux
[arch/arm/mach-omap2/mux.c:258]: (error) Possible null pointer dereference: mux
[arch/arm/mach-omap2/gpmc-onenand.c:178]: (style) Variable 'tick_ns' is assigned a value that is never used
[arch/arm/mach-omap2/gpio.c:56]: (error) Possible null pointer dereference: pdata - otherwise it is redundant to check if pdata is null at line 57
[arch/arm/mach-omap2/devices.c:45]: (style) Variable 'l' is assigned a value that is never used
[arch/arm/mach-omap2/board-omap3evm.c:641] -> [arch/arm/mach-omap2/board-omap3evm.c:639]: (style) Found duplicate branches for if and else.
[arch/arm/mach-omap2/am35xx-emac.c:95]: (style) Variable 'regval' is assigned a value that is never used
[arch/arm/mach-omap2/devices.c:74]: (style) Variable 'l' is assigned a value that is never used
[arch/arm/mach-omap2/pm34xx.c:277]: (style) Variable 'per_prev_state' is assigned a value that is never used
[arch/arm/plat-omap/dmtimer.c:352]: (error) Possible null pointer dereference: timer - otherwise it is redundant to check if timer is null at line 354
[arch/arm/plat-omap/omap_device.c:478]: (style) Variable 'c' is assigned a value that is never used
[arch/arm/plat-omap/usb.c:42]: (style) Variable 'status' is assigned a value that is never used
[arch/arm/mach-omap1/clock.c:197]: (style) Variable 'dpll1_rate' is assigned a value that is never used
[arch/arm/mach-omap1/lcd_dma.c:60]: (style) struct or union member 'lcd_dma_info::size' is never used
[arch/arm/mach-omap1/pm.c:572]: (style) Variable 'entry' is assigned a value that is never used
Some of them are pretty good catches, such as gpio.c:56 and
usb-tusb6010.c:129.
Thanks to Jarkko Nikula for some comments on the sscanf() warnings.
It seems that the kernel sscanf() ignores the field width anyway for the
%d format, so those changes have been dropped from this second version.
Thanks to Daniel Marjamäki <daniel.marjamaki@gmail.com> for pointing
out that a variable was unnecessarily marked static in the
board-omap3evm.c change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Charulatha Varadarajan <charu@ti.com>
Cc: Daniel Marjamäki <daniel.marjamaki@gmail.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Charulatha Varadarajan <charu@ti.com> # for gpio.c
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To fix things like this:
arch/arm/mach-omap2/usb-tusb6010.c:58: error: implicit declaration of function 'memset'
arch/arm/kernel/leds.c:40: error: implicit declaration of function 'strcspn'
arch/arm/kernel/leds.c:40: warning: incompatible implicit declaration of built-in function 'strcspn'
arch/arm/kernel/leds.c:45: error: implicit declaration of function 'strncmp'
arch/arm/kernel/leds.c:55: error: implicit declaration of function 'strlen'
arch/arm/kernel/leds.c:55: warning: incompatible implicit declaration of built-in function 'strlen'
arch/arm/mach-omap2/clockdomain.c:52: error: implicit declaration of function 'strcmp'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
commit fcf173e451
(add names for IRQs in structure resource)
forgot to take care of tusb6010 making it
fail to probe due to a missing resource.
Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The calculations done with sync_clk are anyway in picoseconds
and switching to picoseconds allows sync_clk values that are
not a whole number of nanoseconds - which is sometimes the
case.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "tusb6010 init error 5, -19" and compilation warning from function
tusb6010_platform_retime "warning: 'sysclk_ps' is used uninitialized in this
function".
I suppose commit c094ba34b8f780885d029ce3c2715a194b780e5d was meant to test
for zero fclk_ps instead of sysclk_ps.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In linus' git tree the functions can be found at:
vi arch/arm/mach-omap2/usb-tusb6010.c +200 - tusb6010_platform_retime()
vi arch/arm/mach-omap2/gpmc.c +94 - gpmc_get_fclk_period()
vi arch/arm/mach-omap2/usb-tusb6010.c +53 - tusb_set_async_mode()
vi arch/arm/mach-omap2/usb-tusb6010.c +111 - tusb_set_sync_mode()
is -ENODEV appropriate when sysclk_ps == 0?
This was found by code analysis, please review.
------------------------------>8-------------8<---------------------------------
gpmc_get_fclk_period() may return 0 when gpmc_l3_clk is not enabled. This is
not checked in tusb6010_platform_retime() nor in tusb_set_async_mode() it
seems. In tusb_set_sync_mode() this may result in a division by zero.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add init support for the TUSB6010 EVM board, as connected to H4.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
