Change ADI BSD license to standart 3 clause BSD license for some blackfin arch
code requested by ADI Legal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
SMP kgdb runs into dead loop without this CSYNC when one core single
steps over get_core_lock_noflush and the other executes get_core_lock
as a slave node.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
MDMA io base defined in arch/blackfin/mach-bf561/dma.c do not match the
definition of MDMA MMRs in arch/blackfin/mach-bf561/include/mach/defBF561.h
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Change default clock rate of GPIO based I2C operation for BF533
and BF561 to bring up the I2C interface LCD display
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Macro name for spi controller driver has been modified, so update default
board file accordingly.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
move idle task point to percpu blackfin_cpudata and add smp_timer_broadcast
interface.
enable SUPPLE_1_WAKEUP and add BFIN_IPI_TIMER ipi support.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Add IRQF_NO_SUSPEND | IRQF_FORCE_RESUME to irq flags, supplement irq should
not be disabled when system do suspend.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips,
so move the values to the platform resources.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
This flag is a NOOP and can be removed now.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Bob Liu <lliubbo@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These defines don't accomplish much as GPIO_# is the same thing as #.
Each CPU already provides helpful symbolic defines like GPIO_<PIN>
which everyone uses, so just punt these # ones.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This moves the double fault data used at boot time into a single struct
which can then easily be addressed with indexed loads rather than having
to explicitly load multiple addresses.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default for the Blackfin SPI driver is 8 bits and dma disabled,
so many of the bfin5xx_spi_chip resources are redundant. So punt
those parts.
Further, drivers should themselves be declaring 16 bit transfers,
so for those that do, and for the ones which no longer do 16 bit
transfers, drop the bfin5xx_spi_chip resources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the serial code has been unified in bfin_serial.h, and the
Blackfin UART driver pushed its resources to the boards files, we
don't need these headers anymore.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
We plan to remove cpu_possible_map and cpu_present_map later and we
have proper init_cpu_possible() and init_cpu_present() APIs.
Therefore this patch rewrites platform_init_cpus and platform_prepare_cpus
by their APIs.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Both the BF548-EZKIT and the BF561-EZKIT use top boot flashes, so now
that Das U-Boot uses the last small sector for its environment, update
their nor layout in the kernel accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
After some cache setup reordering changesets, the blackfin_cpudata init
was left behind. While cpu0's data was correct, cpu1's data was not.
Not that big of a deal as these are only used in the cpuinfo output, but
should still be fixed. So move the setup of these fields to the common
cache setup function to avoid this happening again in the future.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These files had a lot of whitespace damage, mostly due to copying and
pasting original files that had damage.
The BF561 header also had a lot of unused CONFIG_DEF_xxx defines, so
punt them all.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Start a new common IRQ header and move all of the CEC pieces there. This
lets the individual part headers worry just about its SIC defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the trigger type in irq_data and check level type instead of
looking at desc->handle_irq.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
When CoreB wakes up, it needs to read variables that CoreA might have
modified, and might be in CoreB's cache. So kill CoreB's cache before
going to sleep so that when we wake up, we are in a coherent state.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In order to safely work around anomaly 05000491, we have to execute IFLUSH
from L1 instruction sram. The trouble with multi-core systems is that all
L1 sram is visible only to the active core. So we can't just place the
functions into L1 and call it directly. We need to setup a jump table and
place the entry point in external memory. This will call the right func
based on the active core.
In the process, convert from the manual relocation of a small bit of code
into Core B's L1 to the more general framework we already have in place
for loading arbitrary pieces of code into L1.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Re-use some of the existing cpu hotplugging code in the process.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since coreb_trampoline_start() calls coreb_start(), they need to be in
the same section.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When run kgdb testing, it looks like coreb hangs in single step or trap
exception without handling anomaly 05000257 properly on bf561 v0.5. But,
the anomaly list says it apply to bf561 v0.4 and bellow. Apply its work
around to 0.5 temporarily until the behavior and the root cause can be
confirmed by the hardware team.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
KGDB single step in SMP kernel may hang forever in flushinv without a
CSYNC ahead. This is because the core internal write buffers need to
be flushed before invalidating the data cache to make sure the insn
fetch is not out of sync.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently, sending an interprocessor interrupt (IPI) requires building up
a message dynamically which means memory allocation. But often times, we
will want to send an IPI in low level contexts where allocation is not
possible which may lead to a panic(). So create a per-cpu static array
for the message queue and use that instead.
Further, while we have two supplemental interrupts, we are currently only
using one of them. So use the second one for the most common IPI message
of all -- smp_send_reschedule(). This avoids ugly contention for locks
which in turn would require an IPI message ...
In general, this improves SMP performance, and in some cases allows the
SMP port to work in places it wouldn't before. Such as the PREEMPT_RT
state where the slab is protected by a per-cpu spin lock. If the slab
kmalloc/kfree were to put the task to sleep, and that task was actually
the IPI handler, then the system falls down yet again.
After running some various stress tests on the system, the static limit
of 5 messages seems to work. On the off chance even this overflows, we
simply panic(), and we can review that scenario to see if the limit needs
to be increased a bit more.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF561 mem_map.h header has the __ASSEMBLY__/CONFIG_SMP checks out
of order which leads to build errors for assembly code that happens to
include this file.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This function takes an irq_handler_t function, but the prototype in
the header doesn't match the function definition. This is due to the
smp headers needing to avoid circular dependencies. So change the
function to take a simple pointer.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These were only included because of the irq handling of the PLL funcs,
and those PLL funcs have been moved out into their own header now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The main asm/blackfin.h header will pull in mach/blackfin.h to get
all the fun Blackfin defines. So having any of the sub-mach headers
trying to include asm/blackfin.h makes no sense -- punt it.
The mach/blackfin.h header takes care of including the part-specific
def headers which in turn will include any other needed def file.
Similarly, it takes care of pulling in the part-specific cdef header.
So move this logic out of the blackfin.h when necessary.
Further, make sure the cdef headers do not waste time including the
def headers again.
Since all parts need the common def/cdef headers, move this logic
out of the part-specific headers and into the mach/blackfin.h file.
Finally, we need to split the BF539 def header since the BF538 does
not have MXVR and we don't want to expose those MMRs.
So now all parts should have the same behavior:
mach/blackfin.h
asm/def_LPBlackfin.h
part-specific def.h
if ! asm
asm/cdef_LPBlackfin.h
part-specific cdef.h
And the sub def/cdef headers only tail into what they need.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the same naming convention for DMA traffic MMRs (most were legacy
anyways) so we can avoid useless ifdef trees.
Same goes for MDMA names -- this actually allows us to undo a bunch of
ifdef redirects that existed for this purpose alone.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Each Blackfin port has been duplicating UART structures and defines when
there really is no need for it. So start a new bfin_serial.h header to
unify all these pieces and give ourselves a fresh start.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
