This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
htt stats are not working after htt peer stats display
and also after htt peer stats reset. Trying to dump htt
stats shows "Resource temporarily unavailable".
This is because of "ar->debug.htt_stats.stats_req" member is being
consecutively used for all htt stats without being reset
during the previous usage. Hence assigning NULL to this member
after freeing the allocated memory fixes the issue.
console logs below:
# echo 9 >/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats_type
9
# cat /sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats
cat: can't open '/sys/kernel/debug/ath11k/ipq8074/mac1/htt_stats'
: Resource temporarily unavailable
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588592755-10427-1-git-send-email-ssreeela@codeaurora.org
Fix the following coccicheck warning:
drivers/net/wireless/ath/ath11k/dp_rx.c:2964:1-39: WARNING: Assignment
of 0/1 to bool variable
drivers/net/wireless/ath/ath11k/dp_rx.c:2965:1-38: WARNING: Assignment
of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113336.41249-1-yanaijie@huawei.com
Add the support to attach and map iommu
domain for targets which do not have the
support of TrustZone.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-4-git-send-email-pillair@codeaurora.org
Move the msa resources setup out of qmi init and
setup the msa resources as a part of probe before
the qmi init is done.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586971906-20985-3-git-send-email-pillair@codeaurora.org
The struct cfg80211_wowlan of NET_DETECT WoWLAN feature share the same
struct cfg80211_sched_scan_request together with scheduled scan request
feature, and max_sched_scan_reqs of wiphy is only used for sched scan,
and ath10k does not support scheduled scan request feature, so ath10k
does not set flag NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR, but ath10k
set max_sched_scan_reqs of wiphy to a non zero value 1, then function
nl80211_add_commands_unsplit of cfg80211 will set it support command
NL80211_CMD_START_SCHED_SCAN because max_sched_scan_reqs is a non zero
value, but actually ath10k not support it, then it leads a mismatch result
for sched scan of cfg80211, then application shill found the mismatch and
stop running case of MAC random address scan and then the case fail.
After remove max_sched_scan_reqs value, it keeps match for sched scan and
case of MAC random address scan pass.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20191114050001.4658-1-wgong@codeaurora.org
As the exisiting CE configurations are defined in global, there
are the chances of QCA99X0 family chipsets CE configurations
are getting changed by the ath10k_pci_override_ce_config()
function.
The override will be hit and CE5 configurations will be changed,
when the user bring up the QCA99X0 chipsets along with QCA6174
or QCA9377 chipset. (Bring up QCA99X0 family chipsets after
QCA6174 or QCA9377).
Hence, fixing this issue by moving the global CE configuration
to radio specific CE configuration.
Tested hardware: QCA9888 & QCA6174
Tested firmware: 10.4-3.10-00047 & WLAN.RM.4.4.1.c3-00058
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587649759-14381-1-git-send-email-mkenna@codeaurora.org
In Multi-AP VAP scenario with frequent interface up-down, there is a
chance that ath11k_mgmt_over_wmi_tx_work() will dequeue a skb
corresponding to currently deleted/stopped vdev.
FW will assert on receiving mgmt_tx_wmi cmd for already deleted vdev.
Hence adding validation checks for arvif present on the corresponding
ar before sending mgmt_tx_wmi cmd.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588049126-1490-2-git-send-email-murugana@codeaurora.org
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: d0998eb84e ("ath11k: optimise ath11k_dp_tx_completion_handler")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104621.23752-1-weiyongjun1@huawei.com
'cmd' is malloced in ath10k_bmi_lz_data_large() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: d58f466a5d ("ath10k: add large size for BMI download data for SDIO")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104348.13570-1-weiyongjun1@huawei.com
For legacy mode, tx bitrate not show correct sometimes, for example:
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 19672 bytes (184 packets)
TX: 9851 bytes (87 packets)
signal: -51 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 2.8 MBit/s
This patch use the tx bitrate info from WMI_TLV_PEER_STATS_INFO_EVENTID
report from firmware, and tx bitrate show correct.
iw wlan0 link
Connected to 8c:21:0a:b3:5a:64 (on wlan0)
SSID: tplinkgw
freq: 2462
RX: 13973 bytes (120 packets)
TX: 6737 bytes (57 packets)
signal: -52 dBm
rx bitrate: 54.0 MBit/s
tx bitrate: 54.0 MBit/s
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, it is enabled only for
"qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-5-wgong@codeaurora.org
The rate code and rate kbps report by WMI_TLV_PEER_STATS_INFO_EVENTID
from firmware contains all the bitrate info which include OFDM, CCK,
HT/VHT, and mac80211 need the struct rate_info which include below
parameters:
flags: bitflag of flags from &enum rate_info_flags
mcs: mcs index if struct describes an HT/VHT/HE rate
legacy: bitrate in 100kbit/s for 802.11abg
nss: number of streams (VHT & HE only)
bw: bandwidth (from &enum rate_info_bw)
For OFDM/CCK, its rate kbps indicate the bitrate, for HT/VHT, mac80211
need the above 5 parameters to cacluate the bitrate and show by iw.
After parse the bitrate info, iw show the correct rx bitrate:
localhost ~ # iw wlan0 link
rx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
rx bitrate: 40.5 MBit/s MCS 2 40MHz
rx bitrate: 72.2 MBit/s MCS 7 short GI
rx bitrate: 54.0 MBit/s
rx bitrate: 48.0 MBit/s
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-4-wgong@codeaurora.org
For SDIO chip, its rx indication is struct htt_rx_indication_hl, which
does not include the bitrate info as well as PCIe, for PCIe, it use
function ath10k_htt_rx_h_rates to parse the bitrate info in struct
rx_ppdu_start and then report it to mac80211 via ieee80211_rx_status.
SDIO does not have the same info as PCIe, then iw command can not get
the rx bitrate by "iw wlan0 station dump".
for example, it always show 6.0 MBit/s
localhost ~ # iw wlan0 link
Connected to 3c:28:6d:96:fd:69 (on wlan0)
SSID: kukui_test
freq: 5180
RX: 111800 bytes (595 packets)
TX: 35419 bytes (202 packets)
signal: -41 dBm
rx bitrate: 6.0 MBit/s
This patch is to send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware
for ath10k_sta_statistics and save the rx bitrate for WMI event
WMI_TLV_PEER_STATS_INFO_EVENTID.
This patch only effect SDIO chip, ath10k_mac_sta_get_peer_stats_info
has check for bitrate_statistics of hw_params, this patch only enable
it for "qca6174 hw3.2 sdio".
Tested with QCA6174 SDIO firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-3-wgong@codeaurora.org
For wmi tlv type, firmware disable peer stats info by default, after
enable it, firmware will report WMI_TLV_PEER_STATS_INFO_EVENTID if
ath10k send WMI_TLV_REQUEST_PEER_STATS_INFO_CMDID to firmware.
Enable it will only set a flag in firmware, firmware will not report
it without receive request WMI command.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427080416.8265-2-wgong@codeaurora.org
The '>' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath5k/ani.c:504:56-61: WARNING: conversion to
bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094037.23048-1-yanaijie@huawei.com
ADC & I/Q calibrations could take infinite time to comple, since they
depend on received frames. In particular the I/Q mismatch calibration
requires receiving of OFDM frames for completion. But in the 2.4GHz
band, a station could receive only CCK frames for a very long time.
And while we wait for the completion of one of the mentioned
calibrations, the NF calibration is blocked. Moreover, in some
environments, I/Q calibration is unable to complete until a correct
noise calibration will be performed due to AGC behaviour.
In order to avoid delaying NF calibration on forever, limit the maximum
duration of ADCs & I/Q calibrations. If the calibration is not completed
within the maximum time, it will be interrupted and a next calibration
will be performed. The code that selects the next calibration has been
reworked to the loop so incompleted calibration will be respinned later.
Ð maximum calibration time of 30 seconds was selected to give the
calibration enough time to complete and to not interfere with the long
(NF) calibration.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-7-ryazanov.s.a@gmail.com
Previously after the calibration validity period is over,
calibrations are invalidated in a one at time manner. So, for AR9002
family, which has three calibrations, the full recalibration interval
becomes 3 x ATH_RESTART_CALINTERVAL. And each next calibration will be
separated by the ATH_RESTART_CALINTERVAL time from a previous one.
It seems like it is better to do whole recalibration at once. Also, this
change makes the driver behaviour a little simpler. So, invalidate all
calibrations at once at the end of the calibration validity interval.
This change affects only AR9002 chips family, since the AR9003 utilize
only a single calibration.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-6-ryazanov.s.a@gmail.com
NF calibration and other elements of long calibration are usually faster
than ADCs & I/Q calibrations due to independence of receiption of the
OFDM signal. Moreover sometime I/Q calibration can not be completed at
all without preceding NF calibration. This is due to AGC, which has a
habit to block a weak signal without regular NF calibration. Thus, we do
not need to deferr the long calibration forever.
So, if the long calibration is requested, then deferr the ADCs & I/Q
calibration(s) and run the longcal (the NF calibration in particular) to
obtain fresh noise data.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-5-ryazanov.s.a@gmail.com
Each of AGC & I/Q calibrations can take a long time. Long calibration
and NF calibration in particular are forbiden for parallel run with
ADC & I/Q calibrations. So, the chip could not be ready to perform the
long calibration at the time of request. And a request to perform the
long calibration may be lost.
In order to fix this, preserve the long calibration request as a
calibration state flag and restore the long calibration request each
time the calibration function is called again (i.e. on each subsequent
ivocation of the short calibration).
This feature will be twice useful after the next change, which will
make it possible to start the long calibration before all ADCs & I/Q
calibrations are completed.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-4-ryazanov.s.a@gmail.com
The NFCAL_PENDING flag is set by the ath9k_hw_start_nfcal() routine,
so there is no reason to set it manually after calling it during the
AR9002 calibrations initialization.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-3-ryazanov.s.a@gmail.com
ADC calibration is only required for a 80 MHz sampling rate (i.e. for
40 MHz channels), when the chip utilizes the pair of ADCs in interleved
mode. Calibration on a 20 MHz channel will never be completed.
Previous channel check is trying to exclude all channels where the
calibration will get stuck. It effectively blocks the calibration run
for HT20 channels, but fails to exclude 20 MHz channels without HT (e.g.
legacy mode channels).
Fix this issue by reworking the channel check to explicitly allow ADCs
gain & DC offset calibrations for HT40 channels only. Also update the
complicated comment to make it clear that these calibrations are for
multi-ADC mode only.
Stuck ADCs calibration blocks the NF calibration, what could make it
impossible to work in a noisy evironment: too big Rx attentuation,
invalid RSSI value, etc. So this change is actually more of a NF
calibration fix rather then the ADC calibration fix.
Run tested with AR9220.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424004923.17129-2-ryazanov.s.a@gmail.com
When tx complete is disabled, all tx status will be set with status
HTT_TX_COMPL_STATE_ACK and indicate to mac80211 by ieee80211_tx_status,
then it does not have the statistics for retries and failed packets.
count of tx retries and tx failed of command "iw wlan0 station dump"
are both 0. If tx complete is not disabled, then firmware report the
tx status and ath10k indicate the status to mac80211, then mac80211
save the statistics and command "iw wlan0 station dump" show them.
for example:
localhost ~ # iw dev wlan0 station dump
Station 3c:28:6d:96:fd:69 (on wlan0)
inactive time: 5 ms
rx bytes: 1325012
rx packets: 6477
tx bytes: 85264
tx packets: 518
tx retries: 0
tx failed: 0
This patch only effect chips with tx complete disabled, e.g. SDIO.
with this patch, output of command "iw dev wlan0 station dump":
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 608 ms
rx bytes: 180366
rx packets: 991
tx bytes: 98765577
tx packets: 64624
tx retries: 14682
tx failed: 47086
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423024134.10601-1-wgong@codeaurora.org
When run command "iw dev wlan0 station dump", the rx duration is 0.
When firmware indicate WMI_UPDATE_STATS_EVENTID, extended flag of
statsis not set by default, so firmware do not report rx duration.
one sample:
localhost # iw wlan0 station dump
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 48 ms
rx bytes: 21670
rx packets: 147
tx bytes: 11529
tx packets: 100
tx retries: 88
tx failed: 36
beacon loss: 1
beacon rx: 31
rx drop misc: 47
signal: -72 [-74, -75] dBm
signal avg: -71 [-74, -75] dBm
beacon signal avg: -71 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 0 us
This patch enable firmware's extened flag of stats by setting flag
WMI_TLV_STAT_PEER_EXTD of ar->fw_stats_req_mask which is set in
ath10k_core_init_firmware_features via WMI_REQUEST_STATS_CMDID.
After apply this patch, rx duration show value with the command:
Station c4:04:15:5d:97:22 (on wlan0)
inactive time: 883 ms
rx bytes: 44289
rx packets: 265
tx bytes: 10838
tx packets: 93
tx retries: 899
tx failed: 103
beacon loss: 0
beacon rx: 78
rx drop misc: 46
signal: -71 [-74, -76] dBm
signal avg: -70 [-74, -76] dBm
beacon signal avg: -70 dBm
tx bitrate: 54.0 MBit/s MCS 3 40MHz
rx bitrate: 1.0 MBit/s
rx duration: 358004 us
This patch do not have side effect for all chips, because function
ath10k_debug_fw_stats_request is already exported to debugfs
"fw_stats" and WMI_REQUEST_STATS_CMDID is safely sent after condition
checked by ath10k_peer_stats_enabled in ath10k_sta_statistics.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423022758.5365-1-wgong@codeaurora.org
we are sending the reo flush command for the deleted peer
tid after the ageout period reaches 1 second. This handling
causes reo ring get full when more than 128 clients are
disconnected continuously. so added the count for flush list
and reo flush command is triggered after the list count reaches
the threshold value, it is configured as 64 (half of the reo ring).
This will avoid the situation where reo ring get full.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587552378-4884-1-git-send-email-periyasa@codeaurora.org
sdio chip use DMA buffer to receive TX packet from ath10k, and it has
limitation of each buffer, if the packet size exceed the credit size,
it will trigger error in firmware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422084719.3479-1-wgong@codeaurora.org
The driver is allowing the invalid tx/rx chainmask configuration
(other than 1,3,7,15) set by the user. It causes the firmware
crash due to the invalid chainmask values.
Hence, reject the invalid chainmask values in the driver by not
sending the pdev set command to the firmware.
Tested hardware: QCA9888
Tested firmware: 10.4-3.10-00047
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587495512-29813-1-git-send-email-mkenna@codeaurora.org
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes,
then it has about 290 bytes's waste for each data packet on sdio
transfer path for TX bundle, it will reduce the transmission utilization
ratio for data packet.
This patch enable the small credit size in firmware, firmware will use
the new credit size 1556 bytes, it will increase the transmission
utilization ratio for data packet on TX patch. It results in significant
performance improvement on TX path.
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-3-wgong@codeaurora.org
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
This patch change the TX packet from single packet to a large length
bundle packet, max size is 32, it results in significant performance
improvement on TX path.
Also there's a fourth thread "ath10k_tx_complete_wq" added to ath10k as it
improves TCP RX throughput (values in Mbps):
TCP-RX TCP-TX UDP-RX UDP-TX
use workqueue_tx_complete 423 357 448 412
change it to ar->workqueue 410 360 449 414
change it to ar->workqueue_aux 405 339 446 401
This patch only effect sdio chip, it will not effect PCI, SNOC etc.
It only enable bundle for sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410061400.14231-2-wgong@codeaurora.org
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/debug.c:198:57-62: WARNING: conversion
to bool not needed here
drivers/net/wireless/ath/ath11k/debug.c:218:58-63: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123745.4159-1-yanaijie@huawei.com
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
drivers/net/wireless/ath/ath11k/dp_rx.c:255:46-51: WARNING: conversion
to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420123718.3384-1-yanaijie@huawei.com
This patch is to set register to allow the mbox enter sleep status
if it does not have tx traffic and wakeup it if tx traffic arrive.
After mbox enter sleep status, the soc will enter sleep status by
firmware, this will save power. The power consume drops from about
90mW to about 10mW with this patch.
This patch only effect sdio chip.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-3-git-send-email-kvalo@codeaurora.org
Convert ath10k_hif_swap_mailbox() to a more generic op so that bus drivers can
do more than just swap the mailbox, for example set power save settings like in
the following sdio patch.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587037859-28873-2-git-send-email-kvalo@codeaurora.org
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
should not overwrite the error code. No buffer available then return
invalid. For other failures return the error code of actual failure.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586776872-25766-1-git-send-email-gsamin@codeaurora.org
Rx_filter flags are set with default filter flags during
wifi up/down sequence even though the 'ext_rx_stats' debugfs
is enabled as 1. So, that we are not getting proper per peer
rx_stats.
Hence, fixing this by setting the missing rx_filter when
ext_rx_stats is already set/enabled.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-3-git-send-email-mkenna@codeaurora.org
After setting fixed vht-rate if new station is trying to
assoc with mu_bfee cap, or if a sta is already connected
with mu_bfee cap then set the fixed vht-rate and
reconnecting the sta, FW assert is happening.
So to avoid this, reset the MU_BEAMFORMEE bit in vht->caps,
if mcs_index is invalid for nss 1.
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-2-git-send-email-mkenna@codeaurora.org
Debugfs pdev entries should be cleaned up during the crash
on recovery. If not, mac register will fail for the reason
that it is already registered during core reconfigure.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586538405-16226-1-git-send-email-mkenna@codeaurora.org
During RX, accessing the reo dest ring descriptor directly is consuming
a lot of CPU cycles. Accessing the descriptor after copying it locally
has improved CPU usage by around ~10-15% while measuring throughput
in RX DBTC test cases(all radios are involved in the throughput
measurement).
HW tested: IPQ8074
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421797-885-1-git-send-email-mpubbise@codeaurora.org
Unlike CE interrupts, DP interrupts are not enabled/disabled at
source; they are enabled/disabled only at GIC level, therefore
it is required to set IRQ_DISABLE_UNLAZY flag to avoid spurious
interrupts.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586421013-23025-1-git-send-email-mpubbise@codeaurora.org
Add the pdev index information in the peer object to validate
the peer creation. Ignore the peer creation request, if the given
MAC address is already present in the peer list with same radio.
If we allow the peer creation in above scenario, FW assert will happen.
Above scenario occurred in two cases, where Multiple AP VAP created in
the same radio.
1. when testing tool sends association request to two AP with same
MAC address
2. when a station do roaming from one AP VAP to another AP VAP.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586343795-21422-1-git-send-email-periyasa@codeaurora.org
