With the introduction of the module area on top of the vmalloc area, the
calculation of VMALLOC_START in setup_memory_end() function hasn't been
adjusted. As a result we got vmalloc area 2 Gb (MODULES_LEN) smaller than
it should be and the preceding vmemmap area got extra memory instead.
The patch fixes this calculation error although there were no visible
negative effects.
Apart from that, change 'tmp' variable to 'vmemmap' in memory_end
calculation for better readability.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
By default 3-level paging is used when the kernel is compiled with
kasan support. Add 4-level paging option to support systems with more
then 3TB of physical memory and to cover 4-level paging specific code
with kasan as well.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To lower memory footprint and speed up kasan initialisation detect
EDAT availability and use large pages if possible. As we know how
much memory is needed for initialisation, another simplistic large
page allocator is introduced to avoid memory fragmentation.
Since facilities list is retrieved anyhow, detect noexec support and
adjust pages attributes. Handle noexec kernel option to avoid inconsistent
kasan shadow memory pages flags.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Kasan needs 1/8 of kernel virtual address space to be reserved as the
shadow area. And eventually it requires the shadow memory offset to be
known at compile time (passed to the compiler when full instrumentation
is enabled). Any value picked as the shadow area offset for 3-level
paging would eat up identity mapping on 4-level paging (with 1PB
shadow area size). So, the kernel sticks to 3-level paging when kasan
is enabled. 3TB border is picked as the shadow offset. The memory
layout is adjusted so, that physical memory border does not exceed
KASAN_SHADOW_START and vmemmap does not go below KASAN_SHADOW_END.
Due to the fact that on s390 paging is set up very late and to cover
more code with kasan instrumentation, temporary identity mapping and
final shadow memory are set up early. The shadow memory mapping is
later carried over to init_mm.pgd during paging_init.
For the needs of paging structures allocation and shadow memory
population a primitive allocator is used, which simply chops off
memory blocks from the end of the physical memory.
Kasan currenty doesn't track vmemmap and vmalloc areas.
Current memory layout (for 3-level paging, 2GB physical memory).
---[ Identity Mapping ]---
0x0000000000000000-0x0000000000100000
---[ Kernel Image Start ]---
0x0000000000100000-0x0000000002b00000
---[ Kernel Image End ]---
0x0000000002b00000-0x0000000080000000 2G <- physical memory border
0x0000000080000000-0x0000030000000000 3070G PUD I
---[ Kasan Shadow Start ]---
0x0000030000000000-0x0000030010000000 256M PMD RW X <- shadow for 2G memory
0x0000030010000000-0x0000037ff0000000 523776M PTE RO NX <- kasan zero ro page
0x0000037ff0000000-0x0000038000000000 256M PMD RW X <- shadow for 2G modules
---[ Kasan Shadow End ]---
0x0000038000000000-0x000003d100000000 324G PUD I
---[ vmemmap Area ]---
0x000003d100000000-0x000003e080000000
---[ vmalloc Area ]---
0x000003e080000000-0x000003ff80000000
---[ Modules Area ]---
0x000003ff80000000-0x0000040000000000 2G
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To distinguish zfcpdump case and to be able to parse some of the kernel
command line arguments early (e.g. mem=) ipl block retrieval and command
line construction code is moved to the early boot phase.
"memory_end" is set up correctly respecting "mem=" and hsa_size in case
of the zfcpdump.
arch/s390/boot/string.c is introduced to provide string handling and
command line parsing functions to early boot phase code for the compressed
kernel image case.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print mem_detect info source when memblock=debug is specified.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move memory detection to early boot phase. To store online memory
regions "struct mem_detect_info" has been introduced together with
for_each_mem_detect_block iterator. mem_detect_info is later converted
to memblock.
Also introduces sclp_early_get_meminfo function to get maximum physical
memory and maximum increment number.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove STACK_ORDER and STACK_SIZE in favour of identical THREAD_SIZE_ORDER
and THREAD_SIZE definitions. THREAD_SIZE and THREAD_SIZE_ORDER naming is
misleading since it is used as general kernel stack size information. But
both those definitions are used in the common code and throughout
architectures specific code, so changing the naming is problematic.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With virtually mapped kernel stacks the kernel stack overflow detection
is now fault based, every stack has a guard page in the vmalloc space.
The panic_stack is renamed to nodat_stack and is used for all function
that need to run without DAT, e.g. memcpy_real or do_start_kdump.
The main effect is a reduction in the kernel image size as with vmap
stacks the old style overflow checking that adds two instructions per
function is not needed anymore. Result from bloat-o-meter:
add/remove: 20/1 grow/shrink: 13/26854 up/down: 2198/-216240 (-214042)
In regard to performance the micro-benchmark for fork has a hit of a
few microseconds, allocating 4 pages in vmalloc space is more expensive
compare to an order-2 page allocation. But with real workload I could
not find a noticeable difference.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce PARMAREA_END, and use it for memblock reserve of low
memory, which is used for lowcore, kdump data mover code and page
buffer, early stack and parmarea. There is no need to reserve an
area between PARMAREA_END and the decompressor _ehead.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just add the new machine type number to the two places that matter.
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_EXPOLINE_AUTO=y the call of spectre_v2_auto_early() via
early_initcall is done *after* the early_param functions. This
overwrites any settings done with the nobp/no_spectre_v2/spectre_v2
parameters. The code patching for the kernel is done after the
evaluation of the early parameters but before the early_initcall
is done. The end result is a kernel image that is patched correctly
but the kernel modules are not.
Make sure that the nospec auto detection function is called before the
early parameters are evaluated and before the code patching is done.
Fixes: 6e179d6412 ("s390: add automatic detection of the spectre defense")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The S390 architecture does not support any graphics hardware,
but with the latest support for Virtio GPU in Linux and Virtio
GPU emulation in QEMU, it's possible to enable graphics for
S390 using the Virtio GPU device.
To enable display we need to enable the Linux Virtual Terminal (VT)
layer for S390. But the VT subsystem initializes quite early
at boot so we need a dummy console driver till the Virtio GPU
driver is initialized and we can run the framebuffer console.
The framebuffer console over a Virtio GPU device can be run
in combination with the serial SCLP console (default on S390).
The SCLP console can still be accessed by management applications
(eg: via Libvirt's virsh console).
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <e23b61f4f599ba23881727a1e8880e9d60cc6a48.1519315352.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Common code defines linker symbols which denote sections start/end in
a form of char []. Referencing those symbols as _symbol or &_symbol
yields the same result, but "_symbol" form is more widespread across
newly written code. Convert s390 specific code to this style.
Also removes unused _text symbol definition in boot/compressed/misc.c.
Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add CONFIG_EXPOLINE to enable the use of the new -mindirect-branch= and
-mfunction_return= compiler options to create a kernel fortified against
the specte v2 attack.
With CONFIG_EXPOLINE=y all indirect branches will be issued with an
execute type instruction. For z10 or newer the EXRL instruction will
be used, for older machines the EX instruction. The typical indirect
call
basr %r14,%r1
is replaced with a PC relative call to a new thunk
brasl %r14,__s390x_indirect_jump_r1
The thunk contains the EXRL/EX instruction to the indirect branch
__s390x_indirect_jump_r1:
exrl 0,0f
j .
0: br %r1
The detour via the execute type instruction has a performance impact.
To get rid of the detour the new kernel parameter "nospectre_v2" and
"spectre_v2=[on,off,auto]" can be used. If the parameter is specified
the kernel and module code will be patched at runtime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To be able to switch off specific CPU alternatives with kernel parameters
make a copy of the facility bit mask provided by STFLE and use the copy
for the decision to apply an alternative.
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the arch/s390/kernel/ files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just use MACHINE_HAS_TE to decide if HWCAP_S390_TE needs
to be added to elf_hwcap.
Suggested-by: Dan Horák <dan@danny.cz>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
With commit 7fb2b2d512 ("s390/virtio: remove the old KVM virtio
transport") the pre-ccw virtio transport for s390 was removed. To
complete the removal the uapi header file that contains the related data
structures must also be removed.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The machine check extended save area is needed to store the vector
registers and the guarded storage control block when a CPU is
interrupted by a machine check.
Move the slab cache allocation of the full save area to nmi.c,
for early boot use a static __initdata block.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The boot_vdso_data variable is related to the vdso code, the magic of the
initial vdso area for the early boot and the replacement of it in vdso_init
should all be put into vdso.c.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Implement CPU alternatives, which allows to optionally patch newer
instructions at runtime, based on CPU facilities availability.
A new kernel boot parameter "noaltinstr" disables patching.
Current implementation is derived from x86 alternatives. Although
ideal instructions padding (when altinstr is longer then oldinstr)
is added at compile time, and no oldinstr nops optimization has to be
done at runtime. Also couple of compile time sanity checks are done:
1. oldinstr and altinstr must be <= 254 bytes long,
2. oldinstr and altinstr must not have an odd length.
alternative(oldinstr, altinstr, facility);
alternative_2(oldinstr, altinstr1, facility1, altinstr2, facility2);
Both compile time and runtime padding consists of either 6/4/2 bytes nop
or a jump (brcl) + 2 bytes nop filler if padding is longer then 6 bytes.
.altinstructions and .altinstr_replacement sections are part of
__init_begin : __init_end region and are freed after initialization.
Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The queued spinlock code for s390 follows the principles of the common
code qspinlock implementation but with a few notable differences.
The format of the spinlock_t locking word differs, s390 needs to store
the logical CPU number of the lock holder in the spinlock_t to be able
to use the diagnose 9c directed yield hypervisor call.
The inline code sequences for spin_lock and spin_unlock are nice and
short. The inline portion of a spin_lock now typically looks like this:
lhi %r0,0 # 0 indicates an empty lock
l %r1,0x3a0 # CPU number + 1 from lowcore
cs %r0,%r1,<some_lock> # lock operation
jnz call_wait # on failure call wait function
locked:
...
call_wait:
la %r2,<some_lock>
brasl %r14,arch_spin_lock_wait
j locked
A spin_unlock is as simple as before:
lhi %r0,0
sth %r0,2(%r2) # unlock operation
After a CPU has queued itself it may not enable interrupts again for the
arch_spin_lock_flags() variant. The arch_spin_lock_wait_flags wait function
is removed.
To improve performance the code implements opportunistic lock stealing.
If the wait function finds a spinlock_t that indicates that the lock is
free but there are queued waiters, the CPU may steal the lock up to three
times without queueing itself. The lock stealing update the steal counter
in the lock word to prevent more than 3 steals. The counter is reset at
the time the CPU next in the queue successfully takes the lock.
While the queued spinlocks improve performance in a system with dedicated
CPUs, in a virtualized environment with continuously overcommitted CPUs
the queued spinlocks can have a negative effect on performance. This
is due to the fact that a queued CPU that is preempted by the hypervisor
will block the queue at some point even without holding the lock. With
the classic spinlock it does not matter if a CPU is preempted that waits
for the lock. Therefore use the queued spinlock code only if the system
runs with dedicated CPUs and fall back to classic spinlocks when running
with shared CPUs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If memory is fragmented it is unlikely that large order memory
allocations succeed. This has been an issue with the vmcp device
driver since a long time, since it requires large physical contiguous
memory ares for large responses.
To hopefully resolve this issue make use of the contiguous memory
allocator (cma). This patch adds a vmcp specific vmcp cma area with a
default size of 4MB. The size can be changed either via the
VMCP_CMA_SIZE config option at compile time or with the "vmcp_cma"
kernel parameter (e.g. "vmcp_cma=16m").
For any vmcp response buffers larger than 16k memory from the cma area
will be allocated. If such an allocation fails, there is a fallback to
the buddy allocator.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add detection for machine type 0x3906 and set the ELF platform name
to z14. Add the miscellaneous-instruction-extension 2 facility to
the list of facilities for z14.
And allow to generate code that only runs on a z14 machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The TOD epoch extension adds 8 epoch bits to the TOD clock to provide
a continuous clock after 2042/09/17. The store-clock-extended (STCKE)
instruction will store the epoch index in the first byte of the
16 bytes stored by the instruction. The read_boot_clock64 and the
read_presistent_clock64 functions need to take the additional bits
into account to give the correct result after 2042/09/17.
The clock-comparator register will stay 64 bit wide. The comparison
of the clock-comparator with the TOD clock is limited to bytes
1 to 8 of the extended TOD format. To deal with the overflow problem
due to an epoch change the clock-comparator sign control in CR0 can
be used to switch the comparison of the 64-bit TOD clock with the
clock-comparator to a signed comparison.
The decision between the signed vs. unsigned clock-comparator
comparisons is done at boot time. Only if the TOD clock is in the
second half of a 142 year epoch the signed comparison is used.
This solves the epoch overflow issue as long as the machine is
booted at least once in an epoch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As Eric said,
"what we need to do is move the variable vmcoreinfo_note out of the
kernel's .bss section. And modify the code to regenerate and keep this
information in something like the control page.
Definitely something like this needs a page all to itself, and ideally
far away from any other kernel data structures. I clearly was not
watching closely the data someone decided to keep this silly thing in
the kernel's .bss section."
This patch allocates extra pages for these vmcoreinfo_XXX variables, one
advantage is that it enhances some safety of vmcoreinfo, because
vmcoreinfo now is kept far away from other kernel data structures.
Link: http://lkml.kernel.org/r/1493281021-20737-1-git-send-email-xlpang@redhat.com
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Suggested-by: Eric Biederman <ebiederm@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a new system call to enable the use of guarded storage for
user space processes. The system call takes two arguments, a command
and pointer to a guarded storage control block:
s390_guarded_storage(int command, struct gs_cb *gs_cb);
The second argument is relevant only for the GS_SET_BC_CB command.
The commands in detail:
0 - GS_ENABLE
Enable the guarded storage facility for the current task. The
initial content of the guarded storage control block will be
all zeros. After the enablement the user space code can use
load-guarded-storage-controls instruction (LGSC) to load an
arbitrary control block. While a task is enabled the kernel
will save and restore the current content of the guarded
storage registers on context switch.
1 - GS_DISABLE
Disables the use of the guarded storage facility for the current
task. The kernel will cease to save and restore the content of
the guarded storage registers, the task specific content of
these registers is lost.
2 - GS_SET_BC_CB
Set a broadcast guarded storage control block. This is called
per thread and stores a specific guarded storage control block
in the task struct of the current task. This control block will
be used for the broadcast event GS_BROADCAST.
3 - GS_CLEAR_BC_CB
Clears the broadcast guarded storage control block. The guarded-
storage control block is removed from the task struct that was
established by GS_SET_BC_CB.
4 - GS_BROADCAST
Sends a broadcast to all thread siblings of the current task.
Every sibling that has established a broadcast guarded storage
control block will load this control block and will be enabled
for guarded storage. The broadcast guarded storage control block
is used up, a second broadcast without a refresh of the stored
control block with GS_SET_BC_CB will not have any effect.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
But first introduce a trivial header and update usage sites.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both MACHINE_HAS_PFMF and MACHINE_HAS_HPAGE are just an alias for
MACHINE_HAS_EDAT1. So simply use MACHINE_HAS_EDAT1 instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add hardware capability bits and feature tags to /proc/cpuinfo for
the "Vector Packed Decimal Facility" (tag "vxd" / hwcap bit 2^12)
and the "Vector Enhancements Facility 1" (tag "vxe" / hwcap bit 2^13).
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current implementation of setup_randomness uses the stack address
and therefore the pointer to the SYSIB 3.2.2 block as input data
address. Furthermore the length of the input data is the number of
virtual-machine description blocks which is typically one.
This means that typically a single zero byte is fed to
add_device_randomness.
Fix both of these and use the address of the first virtual machine
description block as input data address and also use the correct
length.
Fixes: bcfcbb6bae ("s390: add system information as device randomness")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit bcfcbb6bae ("s390: add system information as device
randomness") intended to add some virtual machine specific information
to the randomness pool.
Unfortunately it uses the page allocator before it is ready to use. In
result the page allocator always returns NULL and the setup_randomness
function never adds anything to the randomness pool.
To fix this use memblock_alloc and memblock_free instead.
Fixes: bcfcbb6bae ("s390: add system information as device randomness")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
reserve_initrd currently calls memblock_reserve even if the to be
reserved size is zero. Even though the memblock core code can handle
this correctly, it still yields confusing debug messages if
memblock debugging is enabled.
Therefore make sure to not call memblock_reserve with a size of zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to be able to setup the cpu to node mappings early it is a
prerequisite to know which cpus are present. Therefore cpus must be
detected much earlier than before.
For sclp based cpu detection this requires yet another early sclp
call, since the system is not ready to use the regular interrupt and
memory allocations.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When converting from bootmem to memblock I missed a subtle difference:
the memblock_alloc() functions return uninitialized memory, while the
memblock_virt_alloc() functions return zeroed memory.
This led to quite random early boot crashes.
Therefore use the correct version everywhere now.
Hopefully.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When re-adding crash kernel memory within setup_resources() the
function memblock_add() is used. That function will add memory by
default to node "MAX_NUMNODES" instead of node 0, like the memory
detection code does. In case of !NUMA this will trigger this warning
when the kernel generates the vmemmap:
Usage of MAX_NUMNODES is deprecated. Use NUMA_NO_NODE instead
WARNING: CPU: 0 PID: 0 at mm/memblock.c:1261 memblock_virt_alloc_internal+0x76/0x220
CPU: 0 PID: 0 Comm: swapper Not tainted 4.9.0-rc6 #16
Call Trace:
[<0000000000d0b2e8>] memblock_virt_alloc_try_nid+0x88/0xc8
[<000000000083c8ea>] __earlyonly_bootmem_alloc.constprop.1+0x42/0x50
[<000000000083e7f4>] vmemmap_populate+0x1ac/0x1e0
[<0000000000840136>] sparse_mem_map_populate+0x46/0x68
[<0000000000d0c59c>] sparse_init+0x184/0x238
[<0000000000cf45f6>] paging_init+0xbe/0xf8
[<0000000000cf1d4a>] setup_arch+0xa02/0xae0
[<0000000000ced75a>] start_kernel+0x72/0x450
[<0000000000100020>] _stext+0x20/0x80
If NUMA is selected numa_setup_memory() will fix the node assignments
before the vmemmap will be populated; so this warning will only appear
if NUMA is not selected.
To fix this simply use memblock_add_node() and re-add crash kernel
memory explicitly to node 0.
Reported-and-tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 4e042af463 ("s390/kexec: fix crash on resize of reserved memory")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of all remaining alloc_bootmem calls and use memblock_alloc
instead everywhere. This way we get rid of the inconsistent mixture
of alloc_bootmem and memblock_alloc usages.
Two of the alloc_bootmem_low calls within arch/s390/kernel/setup.c are
replaced with memblock_alloc calls that don't enforce that the
allocated memory is below 2GB. This restriction was never necessary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to make the cma infrastructure usable we need to add a small
architecture backend which calls dma_contiguous_reserve.
Otherwise we would end up with the cma allocator enabled, but no pool
where memory can be allocated from.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 variant of commit 15f4eae70d ("x86: Move
thread_info into task_struct").
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert s390 to use a field in the struct lowcore for the CPU
preemption count. It is a bit cheaper to access a lowcore field
compared to a thread_info variable and it removes the depencency
on a task related structure.
bloat-o-meter on the vmlinux image for the default configuration
(CONFIG_PREEMPT_NONE=y) reports a small reduction in text size:
add/remove: 0/0 grow/shrink: 18/578 up/down: 228/-5448 (-5220)
A larger improvement is achieved with the default configuration
but with CONFIG_PREEMPT=y and CONFIG_DEBUG_PREEMPT=n:
add/remove: 2/6 grow/shrink: 59/4477 up/down: 1618/-228762 (-227144)
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 97f2645f35 ("tree-wide: replace config_enabled() with
IS_ENABLED()") mostly killed config_enabled(), but some new users have
appeared for v4.8-rc1. They are all used for a boolean option, so can
be replaced with IS_ENABLED() safely.
Link: http://lkml.kernel.org/r/1471970749-24867-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the same code structure when determining preferred consoles for
Linux running as KVM guest as with Linux running in LPAR and z/VM
guest:
- Extend the console_mode variable to cover vt220 and hvc consoles
- Determine sensible console defaults in conmode_default()
- Remove KVM-special handling in set_preferred_console()
Ensure that the sclp line mode console is also registered when the
vt220 console was selected to not change existing behavior that
someone might be relying on.
As an externally visible change, KVM guest users can now select
the 3270 or 3215 console devices using the conmode= kernel parameter,
provided that support for the corresponding driver was compiled into
the kernel.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Small cleanup patch to use the shorter __section macro everywhere.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reducing the size of reserved memory for the crash kernel will result
in an immediate crash on s390. Reason for that is that we do not
create struct pages for memory that is reserved. If that memory is
freed any access to struct pages which correspond to this memory will
result in invalid memory accesses and a kernel panic.
Fix this by properly creating struct pages when the system gets
initialized. Change the code also to make use of set_memory_ro() and
set_memory_rw() so page tables will be split if required.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Show the dynamic and static cpu mhz of each cpu. Since these values
are per cpu this requires a fundamental extension of the format of
/proc/cpuinfo.
Historically we had only a single line per cpu and a summary at the
top of the file. This format is hardly extendible if we want to add
more per cpu information.
Therefore this patch adds per cpu blocks at the end of /proc/cpuinfo:
cpu : 0
cpu Mhz dynamic : 5504
cpu Mhz static : 5504
cpu : 1
cpu Mhz dynamic : 5504
cpu Mhz static : 5504
cpu : 2
cpu Mhz dynamic : 5504
cpu Mhz static : 5504
cpu : 3
cpu Mhz dynamic : 5504
cpu Mhz static : 5504
Right now each block contains only the dynamic and static cpu mhz,
but it can be easily extended like on every other architecture.
This extension is supposed to be compatible with the old format.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
