The ath3k driver is treating the version information badly when it
comes to loading the right firmware version and comparing that it
actually matches with the hardware.
Initially this showed up as this:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:373:17: warning: cast to restricted __le32
drivers/bluetooth/ath3k.c:435:17: warning: cast to restricted __le32
However when fixing this by actually using __packed and __le32 for
the ath3_version structure, more issues came up:
CHECK drivers/bluetooth/ath3k.c
drivers/bluetooth/ath3k.c:381:32: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:381:32: expected restricted __le32 [usertype] rom_version
drivers/bluetooth/ath3k.c:381:32: got int [signed] <noident>
drivers/bluetooth/ath3k.c:382:34: warning: incorrect type in assignment (different base types)
drivers/bluetooth/ath3k.c:382:34: expected restricted __le32 [usertype] build_version
drivers/bluetooth/ath3k.c:382:34: got int [signed] <noident>
drivers/bluetooth/ath3k.c:386:28: warning: restricted __le32 degrades to integer
drivers/bluetooth/ath3k.c:386:56: warning: restricted __le32 degrades to integer
This patch fixes every instance of the firmware version handling and
makes sure it is endian safe and uses proper unaligned access.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
.set_bdaddr handler is implemented for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implemented .set_bdaddr handler provided by bluetooth stack for
Marvell devices for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should suspend hci device and purge remaining data in tx queue
before enabling host sleep in firmware. If any data is sent to
firmware after host sleep is activated, firmware may end up
sending a TX_DONE interrupt to driver. If this interrupt gets
delivered to host while the SDIO host controller is suspending,
it may crash the system.
Conversely, in resume handler, we should resume hci device after
host sleep is de-activated.
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The protocol for the UART might be configured, but that does not
mean the HCI device is registered. Return an error in that case
and only return the index number when HCI_UART_REGISTERED is set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The quirk for enabling external configuration with UART needs to be
provided via the HCI UART flags. Add a new flag for it and declare
it as valid.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing unknown or invalid flags to the HCI UART driver should
result in an error. So check which flags are valid and otherwise
return an error.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to
indicate that isochronous endpoints are not needed for CSR USB
sniffer devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The interrupt interface for the Intel USB bootloader devices is only
enabled after receiving SetInterface(0, AltSetting=0). When this USB
command is not send, then no HCI events will be received.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The module parameters to ignore devices based on USB VID/PID are not
needed at all. So just remove them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for configuring the hci_vhci virtual controllers
to require a setup stage using HCI_QUIRK_EXTERNAL_CONFIG. With this
option the virtual controller will start out as unconfigured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Broadcom USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Intel USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for configuring the hci_vhci virtual controllers
as a raw-only device using HCI_QUIRK_RAW_DEVICE. This is useful for
testing the kernel internal infrastructure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch fixes the following sparse warning caused by a missing
declaration in the header file:
drivers/bluetooth/btmrvl_main.c:218:5: warning: symbol 'btmrvl_pscan_window_reporting' was not declared. Should it be static?
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom BCM20702A0 USB controllers might come with the default
address 00:20:70:02:A0:00 when booting up. If this happens, then warn
about such address being used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Intel Bluetooth controllers come with a default address. If this
address is found, print an error to warn the user about it.
The controller is fully operational, but the danger of duplicate
Bluetooth addresses might causes issues. At least with a clear
error it becomes easier to debug these cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Intel based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Broadcom based USB devices add support for configuration of
the public device address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After BT_CMD_HOST_SLEEP_ENABLE command finishes, driver should
wait until getting BT_EVENT_HOST_SLEEP_ENABLE event to complete
suspend procedure.
Without this patch the suspend handler would return success
earlier. By the time when the BT_EVENT_HOST_SLEEP_ENABLE event
comes in the controller driver could have already turned off the
bus clock. This causes kernel crash or system reboot eventually.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Jeff CF Chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A vendor specific command is sent to firmware during
initialization to enable this feature. This command is for
SD8897 only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
h5_reset_rx is unconditionally called at the end of
h5_complete_rx_pkt, no need to call it anymore after
that.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When detecting a non-link packet, h5_reset_rx() frees the Rx skb.
Not returning after that will cause the upcoming h5_rx_payload()
call to dereference a now NULL Rx skb and trigger a kernel oops.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This reverts commit ca58e594da.
For some unclear reason this patch tries to add suport for the
product ID 0xe005, but it ends up adding product ID 0x3005 to
all the tables. This is obviously wrong and causing multiple
issues.
The original patch seemed to be fine, but what ended up in 3.15
is not what the patch intended. The commit 0a3658cccd is
already present and adds support for this hardware. This means
only revert of this broken commit is requird.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Alexander Holler <holler@ahsoftware.de>
Cc: stable@vger.kernel.org # 3.15.x
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXgoACgkQMUfUDdst+ymdSwCgwL0xmWjFYr/UbJ4LslOZ29Q4
BFQAoKyYe9LsfEyodBPabxJjKUtj1htz
=ZGSN
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into next
Pull tty/serial driver updates from Greg KH:
"Here is the big tty / serial driver pull request for 3.16-rc1.
A variety of different serial driver fixes and updates and additions,
nothing huge, and no real major core tty changes at all.
All have been in linux-next for a while"
* tag 'tty-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (84 commits)
Revert "serial: imx: remove the DMA wait queue"
serial: kgdb_nmi: Improve console integration with KDB I/O
serial: kgdb_nmi: Switch from tasklets to real timers
serial: kgdb_nmi: Use container_of() to locate private data
serial: cpm_uart: No LF conversion in put_poll_char()
serial: sirf: Fix compilation failure
console: Remove superfluous readonly check
console: Use explicit pointer type for vc_uni_pagedir* fields
vgacon: Fix & cleanup refcounting
ARM: tty: Move HVC DCC assembly to arch/arm
tty/hvc/hvc_console: Fix wakeup of HVC thread on hvc_kick()
drivers/tty/n_hdlc.c: replace kmalloc/memset by kzalloc
vt: emulate 8- and 24-bit colour codes.
printk/of_serial: fix serial console cessation part way through boot.
serial: 8250_dma: check the result of TX buffer mapping
serial: uart: add hw flow control support configuration
tty/serial: at91: add interrupts for modem control lines
tty/serial: at91: use mctrl_gpio helpers
tty/serial: Add GPIOLIB helpers for controlling modem lines
ARM: at91: gpio: implement get_direction
...
Invoking usb_sndbulkpipe() on same pipe for same purpose only once is
enough.
Signed-off-by: Adam Lee <adam8157@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After hardware reset, some BCM Bluetooth adapters obtain their initial firmware
from OTPROM chip. Once this initial firmware is running, the firmware can be
further upgraded over HCI interface with .hcd files provided by Broadcom. This
is also known as "patch RAM" support. This change implements that.
If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues
to operate with the initial firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found
If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and
it starts using the new firmware. Sample kernel log:
hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e
Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit d2bee8fb6e.
Enabling autosuspend for Intel Bluetooth devices has been shown to not
work reliable. It does work for some people with certain combinations
of USB host controllers, but for others it puts the device to sleep and
it will not wake up for any event.
These events can be important ones like HCI Inquiry Complete or HCI
Connection Request. The events will arrive as soon as you poke the
device with a new command, but that is not something we can do in
these cases.
Initially there were patches to the xHCI USB controller that fixed
this for some people, but not for all. This could be well a problem
somewhere in the USB subsystem or in the USB host controllers or
just plain a hardware issue somewhere. At this moment we just do
not know and the only safe action is to revert this patch.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Tedd Ho-Jeong An <tedd.an@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
LDISCs shouldn't call tty->ops->write() from within
->write_wakeup().
->write_wakeup() is called with port lock taken and
IRQs disabled, tty->ops->write() will try to acquire
the same port lock and we will deadlock.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Andreas Bießmann <andreas@biessmann.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change subcmd parameter from int to u8 to match its use:
btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
For SD8897, CMD52 write_to_clear may have missing interrupts
under certain corner case condition. Use CMD53 read-to-clear
to fix the problem.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make sure no timer callback is running before releasing the
datastructure which contains it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If vendor specific HCI commands are received from application,
we should send corresponding events to stack.
These events should be consumed in driver, only if they are for
the internal HCI commands generated by driver.
This patch fixes the vendor command 0x3f stuck problem with
above mentioned change. For example,
hcitool cmd 3f 22 fe 06 22 21 20 43 50 00
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The version is always in little endian format. This patch makes the
driver work on both little and big endian CPUs.
Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove assignment in if-statements to be consistent with the coding
style.
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When stopping BCSP/H5, stop the retransmission timer before proceeding
to clean up packet queues. The previous code had a race condition where
the timer could trigger after the packet lists and protocol structure
had been removed which led to dereferencing NULL or use-after-free bugs.
Signed-off-by: Michael Knudsen <m.knudsen@samsung.com>
Reported-by: Kirill Tkhai <ktkhai@parallels.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This will help to manage table of supported IDs.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit bfacbb9 (Bluetooth: Use devname:vhci module alias for virtual HCI
driver) added the module alias to hci_vhci module so it's possible to
create the /dev/vhci node. However creating an alias without
specifying the minor doesn't allow us to create the node ahead,
triggerring module auto-load when it's first accessed.
Starting with depmod from kmod 16 we started to warn if there's a
devname alias without specifying the major and minor.
Let's do the same done for uhid, kvm, fuse and others, specifying a
fixed minor. In systems with systemd as the init the following will
happen: on early boot systemd will call "kmod static-nodes" to read
/lib/modules/$(uname -r)/modules.devname and then create the nodes. When
first accessed these "dead" nodes will trigger the module loading.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 2.0 (0x3) HCI Revision: 0x3000
LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
Manufacturer: Broadcom Corporation (15)
The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.
For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.
During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.
Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.
What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.
T: Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#= 9 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 1.00
S: Manufacturer=Bluetooth v2.0
S: Product=Bluetooth V2.0 Dongle
T: Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 0.07
In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The register for setting the SDIO card mode of a Type-B Bluetooth card
is called MD SET. The MD STAT register is used for reading the current
mode back.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth virtual HCI driver is using a misc character device to
allow emulation of HCI devices from userspace. This change enables the
support for vectored writes. Previously this was failing with EINVAL
since no complete H:4 packet was written.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Socket Bluetooth SDIO cards are branded versions of Toshiba SD-BT2
and they do not support sending HCI_Reset as first command. To make
this card work the HCI_QUIRK_RESET_ON_CLOSE quirk needs to be set
before registering the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch enables autosuspend for Intel Bluetooth device.
After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.
"The USB specification states that all USB devices must support power
management. Nevertheless, the sad fact is that many devices do not
support it very well. You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely. This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.
For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs. Hubs, at least, appear to be reasonably well-behaved in
this regard."
This document also described how the driver can enables the autosuspend
by using an USB api.
"Drivers can enable autosuspend for their devices by calling
usb_enable_autosuspend(struct usb_device *udev);
in their probe() routine, if they know that the device is capable of
suspending and resuming correctly. This is exactly equivalent to
writing "auto" to the device's power/control attribute."
For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The device tree property can define the cal-data in proper order.
There is no need to swap the bytes in driver.
Also remove the redundant cal-data memory copy after removing the
byte swapping.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some ARM versions of Chromebook need to download a new calibration
data from host driver to firmware. They do have EEPROM but still
need a piece of new calibration data in test mode.
The cal-data is platform dependent. It's simpler and more feasible
to use device tree based cal-data instead of configuration file
based cal-data.
This patch remove configuration file based cal-data downloading
and replace it using cal-data from device tree.
When CONFIG_OF is not selected, or the specific property is not
present in the device tree, the calibration downloading will not
happen.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ath3k_table[] and ath3k_blist_tbl[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bpa10x_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_table[] device table can be declared as const
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of vhci_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of hci_uart_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of dtl1_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btuart_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of btmrvl_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bt3c_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bluecard_hci_send_frame() is always valid. If it
were not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hdev parameter of bfusb_send_frame() is always valid. If it were
not valid, then it would have crashed earlier in the call chain.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The function h4_check_data_len() is actually not used. So just
remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btmrvl_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The dtl1_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btuart_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt3c_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bluecard_hci_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bfusb_ioctl() function is not used and thus remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.
In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These
devices default to hid mode for BIOS use. This means that after having been
reset they will revert to HID mode, and are no longer usable as a HCI.
Therefor it is a very bad idea to just blindly make reset_resume point to
the regular resume handler. Note that the btusb driver has no clue how to
switch these devices from hid to hci mode, this is done in userspace through
udev rules, so the proper way to deal with this is to not have a reset-resume
handler and instead let the usb-system re-enumerate the device, and re-run
the udev rules.
I must also note, that the commit message for the commit causing this
problem has a very weak motivation for the change:
"Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?"
Making a change solely to silence a warning while also changing important
behavior (normal resume handling versus re-enumeration) requires a commit
message with a proper explanation why it is safe to do so, which clearly lacks
here, and unsurprisingly it turns out to not be safe to make this change.
Reverting the commit in question fixes bt no longer working on my Dell
E6430 after a suspend/resume, and I believe it likely also fixes the
following bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=988481https://bugzilla.redhat.com/show_bug.cgi?id=1010649https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239
This reverts commit 502f769662.
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
A text file containing calibration data in hex format can
be provided at following path:
/lib/firmware/mrvl/sd8797_caldata.conf
The data will be downloaded to firmware during initialization.
Reviewed-by: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace this proprietary structure with the standard one
(struct hci_command_hdr).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Command preparation code is used multiple times. This patch
separate out this common code and create btmrvl_send_sync_cmd()
function.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth protocol and hardware is pretty much all little endian
and so when running sparse via "make C=2" for example, enable the
endian checks by default.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
So far the only option to create a virtual AMP controller was by
setting a module parameter for the hci_vhci driver. This patch adds
the functionality to define inline to create either a BR/EDR or an
AMP controller.
In addition the client will be informed which HCI controller index
it got assigned. That is especially useful for automated end-to-end
testing.
To keep backwards compatibility with existing userspace, the command
for creating a controller type needs to be send right after opening
the device node. If the command is not send, it defaults back to
automatically creating a BR/EDR controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
To allow creating /dev/vhci device node, add the proper module alias for
this driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There are two places where DIV_ROUND_UP may be used. It makes code a bit
clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Memory allocated by vmalloc (including stack) can not be used for DMA,
i.e. data pointer on usb_control_msg() should not point to stack memory.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=977558
Reported-and-tested-by: Andy Lawrence <dr.diesel@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Fix to return -ENOMEM in the skb alloc error handling case
instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is currently a race condition in the btmrvl_remove_card() which
is causing hangs on suspend for OLPC. When the race occurs,
kthread_stop() never returns.
The problem is that btmrvl_service_main_thread() calls kthread_should_stop()
and then does a fair number of things before restarting the loop and
sleeping.
If the thread gets stopped after kthread_should_stop() is checked, but
before the sleep happens, the thread will go to sleep and won't necessarily
be woken up.
Move the kthread_should_stop() check into a race-free place.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register offsets have been changed in SD8897 and newer chips.
Define a new btmrvl_sdio_card_reg map for SD88xx.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
FW does the synchronization of the different modules during init.
It will report different modules, that it is ready at different times.
The fw download 'winner' will be reported fw ready first. Without this
patch, btmrvl was already continuing before the FW told it too. Probably
on behalf of the 'winner' which then never sees FW ready and times out.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If not winner, driver must release the sdio host lock, so the fw
download can progress. While holding the lock fw download is stalled
and the following error is produced:
[ 235.746015] Bluetooth: FW failed to be active in time!
[ 235.752799] Bluetooth: Downloading firmware failed!
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Clean up the code by using native debugfs helpers, instead of implementing
them ourselves:
debugfs_create_u8()
debugfs_create_x16()
debugfs_create_file()
debugfs_remove_recursive()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.
To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.
Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch removes redundant whitespace from the HCI ldisc driver.
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a NULL check for the HCI UART ldisc driver because some
of HCI UART drivers allow hci_uart_tty_receive function to be called
even though the HCI device hasn't been registered yet.
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a check HCI_UART_REGISTERED before reading UART data in
the HCI UART H4 driver. UART data could arrive when inside the
hci_uart_tty_ioctl function after calling test_and_set_bit for
HCI_UART_PROTO_SET but before the hci_uart_set_proto function has
returned.
Backtrace:
[<c05f27ec>] (hci_recv_stream_fragment+0x0/0x74) from [<c04126f4>] (h4_recv+0x18/0x40)
r7:eb1d4d1c r6:eb7683b0 r5:eae8e800 r4:0000000c
[<c04126dc>] (h4_recv+0x0/0x40) from [<c0411870>] (hci_uart_tty_receive+0x6c/0x94)
r5:eae8e800 r4:eb768380
[<c0411804>] (hci_uart_tty_receive+0x0/0x94) from [<c027be88>] (flush_to_ldisc+0x16c/0x17c)
r6:eae8e8d8 r5:eae8e800 r4:eae8e8c8
[<c027bd1c>] (flush_to_ldisc+0x0/0x17c) from [<c0050ae8>] (process_one_work+0x144/0x4d4)
[<c00509a4>] (process_one_work+0x0/0x4d4) from [<c0051208>] (worker_thread+0x180/0x370)
[<c0051088>] (worker_thread+0x0/0x370) from [<c005617c>] (kthread+0x90/0x9c)
[<c00560ec>] (kthread+0x0/0x9c) from [<c003a3a0>] (do_exit+0x0/0x7ec)
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The firmware images are shared with libertas_sdio WiFi chip and used to be
in libertas/ subtree in linux-firmware. As btmrvl_sdio used to look into
the linux-firmware root, it ended up being unsuccessful. Since the
firmware files are not specific to the libertas hardware, they're being
moved into mrvl/ now.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
hci_ldisc's open checks if tty_struct->disc_data is set. And if so it
returns with an error. But nothing ensures disc_data to be NULL. And
since ld->ops->open shall be called only once, we do not need the
check at all. So remove it.
Note that this is not an issue now, but n_tty will start using the
disc_data pointer and this invalid 'if' would trigger then rendering
TTYs over BT unusable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use standard print specifier and remove print_hex_dump_bytes call.
Makes output more sensible:
...
[18809.401218] 00000000: 0b 00 00 fe 5b fc 01 f2 00 00 00 ....[......
...
would be changed to
...
[18809.401218] Bluetooth: hex: 0b 00 00 fe 5b fc 01 f2 00 00 00
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Make code readable by correcting name from buf_block_len to num_blocks
since it represent number of blocks; NOT a length of a block buffer.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Foxconn devices has a vendor specific class of device, we will match them
differently now.
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.
In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Many Broadcom devices has a vendor specific devices class, with this rule
we match all existent and future controllers with this behavior.
We also remove old rules to that matches product id for Broadcom devices.
Tested-by: John Hommel <john.hommel@hp.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a flags variable to the Three-wire UART state
struct and converts the two existing bools in the struct into flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The configuration request/response messages contain a configuration
field which contains the sliding window size (amount of unacked reliable
packets that can be pending). This patch makes sure that we configure
the correct size (minimum of local and remote values) and use it when
determining whether to send new packets or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The implementation of h5_build_packet can be moved into
h5_prepare_pkt since all h5_prepare_pkt does is determine whether the
packet is reliable and then call h5_build_packet.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds on-demand wakeup request sending (and re-sendind) when
we are in low-power state. When the controller enters this state it will
send a sleep message after which the host is not allowed to send any
other packets until a wakeup request has been sent and the woken message
received as a response to it. The wakeup requests are re-sent
periodically until a woken message is received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds tracking for the uninitialized, initialized and active
states for Three-wire UART. This is needed so we can handle periodic
sending of the Link Establishment messages before reaching active state
and so that we do not try to do any higher level HCI data transmission
before reaching active state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds very basic support for the sleep related messages. The
only thing the code does right now is send a wakeup message as soon as
receiving a sleep one, essentially preventing the controller from going
to sleep.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Remove unnecessary debug logs and add some to more centralized places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch takes into use the delayed initialization feature that the
Bluetooth UART framework provides.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch makes it possible to have UART drivers perform an internal
initialization before calling hci_register_dev. This allows moving a lot
of init code from user space (hciattach) to the kernel side, thereby
creating a more controlled/robust initialization process.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch cleans up and reduces indentation in the hci_uart_tty_close
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds basic support for parsing and sending Three-wire UART
Link Control packets.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch should complete the necessary code for sending reliable
Three-wire packets.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds convenience macros for reading Three-wire header values.
This will help make the code more readable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds initial packed encoding and sending support to the
Three-wire UART HCI transport driver.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds basic packet parsing to the Three-wire UART HCI driver
for packets received from the controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds initial support for reliable packets along with the
necessary retransmission timer for the Three-wire UART HCI driver.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds basic state tracking and socket buffer handling to the
Three-wire UART (H5) HCI driver.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds the initial skeleton for Three-wire UART (H5) support
and hooks it up to the HCI UART framework.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch shortens locals scope and adds missing braces. This is a diff
between v1 which was applied and v2 of patch "Bluetooth: btmrvl: Do
not send vendor events to bluetooth stack".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Fix for warnings below:
...
drivers/bluetooth/bt3c_cs.c:667:20: warning: Using plain integer
as NULL pointer
drivers/bluetooth/btuart_cs.c:596:20: warning: Using plain integer
as NULL pointer
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
SD8787 SDIO function 3 (device ID 0x911B) is for Bluetooth AMP.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Most of the include were unnecessary or already included by some other
header.
Replace module.h by export.h where possible.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let the compiler chooses what is best.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to
reset device on close instead of init, not to not reset at all.
Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Currently debugfs commands "hscfgcmd" and "gpiogap" are provided
for host sleep configuration. But if user doesn't configure host
sleep parameters using these commands, host sleep activation is
failed during suspend (support for suspend and resume handlers is
added in next patch).
Default host sleep configuration is done during driver initialisation
in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The alternate setting must be dynamically set according to the number of
active SCO links, and the bit depth of the audio. The possible values
for the alternate setting are described in the Bluetooth Core
Specification, Volume 4, Part B, section 2.1.1.
Signed-off-by: Mikel Astiz <mikel.astiz.oss@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
release_firmware() deals gracefullt with NULL pointers so there's no
reason to test for one prior to calling the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The comment in ./fs/open.c clearly states that nonseekable_open() will
never fail. Therefore, we can safely ignore the return code. This is the
recommended way to deal with nonseekable_open().
Our current code looks like nonseekable_open() is checked for the return
code. However, if we check the return code, we must also kfree() our
private data if the open fails. To avoid this overhead and to avoid
confusion, we simply drop the return code and return 0.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We initialize the "struct device" in hci_alloc_dev() for a long time now
so we can access hdev->dev.parent directly. Hence, we can drop the
temporary field hdev->parent which is used in no other place than
hci_add_sysfs().
SET_HCIDEV_DEV() is never called after registering a device by the
drivers so we do not overwrite internal device-state. Furthermore,
hdev->dev is initialized to 0 by kzalloc() inside hci_alloc_dev() so the
default behavior with dev.parent = NULL is kept.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was trying to backport the following commit to RHEL-6
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 1
bDeviceProtocol 1
bMaxPacketSize0 64
idVendor 0x0a5c Broadcom Corp.
idProduct 0x21e1
bcdDevice 1.12
iManufacturer 1 Broadcom Corp
iProduct 2 BCM20702A0
iSerial 3 60D819F0338C
bNumConfigurations 1
Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.
Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads
correctly.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
