Implement an ARM delay timer to be used for udelay(). This allows us to
skip the delay loop calibration at boot on Marvell BG2, BG2Q, BG2CD
platforms. And after this patch, udelay() will be unaffected by CPU
frequency changes.
Note: Although in case there are several possible delay timers, we may
not select the "best" delay timer. Take one Marvell Berlin platform for
example: we have arch timer and dw-apb timer. The arch timer freq is
25MHZ while the dw-apb timer freq is 100MHZ, current selection would
choose the dw-apb timer. But the dw apb timer is on the APB bus while
arch timer sits in CPU, the cost of accessing the apb timer is higher
than the arch timer. We could introduce "rating" concept to delay
timer, but this approach "brings a lot of complexity and workarounds
in the code for a small benefit" as pointed out by Daniel.
Later, Arnd pointed out "However, we could argue that this actually
doesn't matter at all, because the entire point of the ndelay()/
udelay()/mdelay() functions is to waste CPU cycles doing not much at
all, so we can just as well waste them reading the timer register
than spinning on the CPU reading the arch timer more often.", so we
just simply register the dw apb base delay timer.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The dw_apb_timer_of timer is using __raw_readl() to access the
timer register, which is causing issues when the system is
running in big endian mode. Fix this by using readl_relaxed()
which should account for the endian settings.
This fixes issues where the time jumps around in the dmesg
output due to returnling __le32 values.
For an example, these two console lines show time running
backwards:
[ 49.882572] CPU1: failed to come online
[ 43.282457] Brought up 1 CPUs
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Linux ARM Kernel <linux-arm-kernel@lists.infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: digetx@gmail.com
Cc: hdegoede@redhat.com
Cc: laurent.pinchart+renesas@ideasonboard.com
Cc: maxime.ripard@free-electrons.com
Cc: viresh.kumar@linaro.org
Link: http://lkml.kernel.org/r/1427746633-9137-10-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We do not need to trace read_sched_clock function,
so add notrace attribute for this function.
Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In commit 620f5e1cbf (dts: Rename DW APB timer compatible strings), both
"snps,dw-apb-timer-sp" and "snps,dw-apb-timer-osc" were deprecated in place
of "snps,dw-apb-timer". But the driver also needs to be udpated in order to
support this new binding "snps,dw-apb-timer".
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The read_sched_clock should return the ~value because the clock is a
countdown implementation. read_sched_clock() should be the same as
__apbt_read_clocksource().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
These are all only called by dw_apb_timer_init which is an __init
function, too
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Instead of letting each driver call of_node_put do it centrally in the
loop that also calls the CLOCKSOURCE_OF_DECLARE callbacks. This is less
prone to error and also moves getting and putting the references into the
same function.
Consequently all respective of_node_put calls in drivers are removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
This reverts commit 55a68c23e0.
In order to avoid a collision with dw_apb_timer changes in
the arm-soc tree, revert this change.
I'm leaving it to the arm-soc folks to sort out if they want
to keep the other side of the collision or if they're just going
to back it all out and try again during the next release cycle.
Reported-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
dw_apb_timer_init used to search the devicetree for matching timer
devices, making calls to it from board files necessary.
Change the dw_apb_timer_init to work with CLOCKSOURCE_OF_DECLARE.
With this change the function gets called once for each timer node
and tracks these number of calls to attach clockevent and clocksource
devices to the nodes.
Also remove the calls to dw_apb_timer_init from all previous users, as
clocksource_of_init is the default for init_time now.
Tested on the upcoming rk3066 code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Add the possibility to get the clock-frequency from a timer clock instead
of specifying it as dt property. Additionally also add the possibility
to also define a controlling periphal clock for the timer block.
The clock-frequency property is kept to act as fallback if no clocks
are specified.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Currently the dw_apb_timer always expects a separate special timer to be
availbable for the sched_clock. Some devices using dw_apb_timers do not
have this sptimer but can use the clocksource as sched_clock instead.
Therefore enable the driver to distiguish between devices with and without
sptimer based on the devicetree data and select the correct timer as
sched_clock.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
irq_of_parse_and_map() returns 0 on error, while the code checks for NO_IRQ.
This breaks on platforms that have NO_IRQ != 0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The time.h header seems not to be used by current code.
Removing this include allows the driver to build on other
architecture that do not have this header.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[tweaked commit message and header]
Signed-off-by: John Stultz <john.stultz@linaro.org>
It seems we made a mistake when creating dw_apb_timer_of.c:
picoxcell sched_clock had parts that were not related to
dw_apb_timer, yet we moved them to dw_apb_timer_of, and tried to
use them on socfpga.
This results in system where user/system time is not measured
properly, as demonstrated by
time dd if=/dev/urandom of=/dev/zero bs=100000 count=100
So this patch switches sched_clock to hardware that exists on both
platforms, and adds missing of_node_put() in dw_apb_timer_init().
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Make a common device tree glue for clocksource/dw_apb_timer.
Move mach-picoxcell/time.c to be a generic device tree application
of the dw_apb_timer.
Configure mach-picoxcell to use the dw_apb_timer_of device tree
implementation in drivers/clocksource.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
