* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
The following error is seen in some case when mounting rootfs from
SD/MMC cards.
Waiting for root device /dev/mmcblk0p1...
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 SDC 3.74 GiB
mmcblk0: p1
mmc1: Timeout waiting for hardware interrupt.
mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 3678225
Buffer I/O error on device mmcblk0p1, logical block 458754
lost page write due to I/O error on mmcblk0p1
This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The AUTO_ZRELADDR selection for ARCH_IMX_V4_V5 and ARCH_MX5 should
really be mutually exclusive to ZBOOT_ROM just like what ARCH_IMX_V6_V7
does.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The config symbol ARCH_MX3 has been removed by commit 'a89cf59
arm/imx: merge i.MX3 and i.MX6', and it should not be referenced
any more.
The patch also change ARCH_MX* to SOC_IMX* for other platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable the headphone detection gpio on tegra platform.
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Ventana uses the same SDHCI GPIOs as Seaboard; PI6 (70) is the power GPIO
for the SD port, and there is no power GPIO for the MMC chip.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
*_pinmux_init() register the GPIO and pinmux devices so that they're ready
before any other device needs them.
*_pinmux_init() are also called by board-dt.c in order to set up the GPIO
and pinmux configurations. In this case, if we register the devices, they
end up being probed once due to this registration, and a second time due
to a device-tree node (or vice-versa). The second probe fails since the
memory regions are already requested. Besides, we don't actually want the
duplicated devices.
To avoid this duplicate registration, modify *_pinmux_init() to check
whether it's running on a DT machine. If not, register the pinmux devices.
If so, don't register them.
Finally, modify board-dt.c to call the *_pinmux_init() after all devices have
been instantiated from device-tree. This allows the GPIO and pinmux devices
to be instantiated and initialized before calling functions to configure the
hardware.
This has one disadvantage: The pinmux and GPIO initialization now happens
after /all/ devices are instantiated, rather than after just gpio and
pinmux but before anything else. So the correct HW configuration is not
in place when e.g. the SD/MMC device is probed. Long-term, this should be
solved by doing both:
a) Initializing the HW state from DT nodes during GPIO and pinmux device
probe.
b) Using the deferred driver probe mechanism, so that drivers can defer
their probe until after the gpio and pinmux drivers have probed.
v2: s/int is_dt/bool is_dt/
v3: Use of_machine_is_compatible inside *_pinmux_init() rather than passing
an explicit parameter into the function from outside.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since 193ab2a607, various AT91 boards don't
register USBA adapters anymore due to depending on a now non-existing
symbol. Fix the symbol name.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: stable@kernel.org
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
VMALLOC_END is defined in terms of AT91_VIRT_BASE but this needs
mach/hardware.h for it's definition.
In file included from arch/arm/mach-at91/board-usb-a926x.c:26:0:
include/linux/mm.h: In function 'is_vmalloc_addr':
include/linux/mm.h:305:41: error: 'AT91_VIRT_BASE' undeclared (first use in this function)
include/linux/mm.h:305:41: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
In commit fb149f9e28 we introduce ioremap support for static map_io, we do
not need this register entry anymore.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
639da5ee3 (ARM: add an extra temp register to the low level debugging
addruart macro) didn't include picoxcell as it hadn't been merged at the
time. Fix up the compile breakage by adding the extra temp parameter.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
CONFIG_MSM_SCM uses the smc instruction, which with some
toolchains requires a ".arch_extension" directive.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
The merge commit "526b264 Merge branch 'imx/cleanup' into imx/devel"
left a duplicated mx28_add_mxs_mmc() call, which causes the problem
below during boot.
kobject_add_internal failed for mxs-mmc.1 with -EEXIST, don't try
to register things with the same name in the same directory.
The patch removes this leftover and also change mmc0 adding to align
with mmc1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.
Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.
Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.
This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.
Thanks to Tomi and Sricharan for some additional testing.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP2/3 dss_core has a reset status flag in sysstatus register. Add
SYSS_HAS_RESET_STATUS flag to HWMOD data so it can be used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP4 HWMOD data currently contains errors with DSS clocks:
dss_hdmi and dss_venc have their main_clks wrong. The clocks should be
dss_48mhz_clk and dss_tv_clk, respectively.
These problems were temporarily fixed with the DSS patches
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), and df5d3ed23c ("OMAP:
DSS2: HDMI: fix hdmi clock name"), which can be reverted after this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This causes the HWMOD frameworks boot-time
reset to fail, possibly leaving the DSS hardware in undefined state.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core. The flag
is actually not used on OMAP4, because dss_core hardware does not have
soft-reset functionality and thus the HWMOD framework never resets nor
waits for the reset to finish.
However, while the flag is not strictly needed currently, I think it
represents the HW correctly: all the DSS clocks should be enabled after
power-on to allow DSS hardware to finish its reset.
A custom reset function will be added in the following patches which
manages this correctly for OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the dss_dss_clk from dss_core's opt-clocks. dss_dss_clk already
defined as the dss main_clk, and thus is not needed as an opt-clock.
Remove opt-clocks for dss_dispc, as dispc only uses the main_clk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP3 HWMOD data currently contains these errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_dsi is missing ick and sys_clk
- dss_venc is missing dss_96m_fck opt-clock, which is required on
OMAP3430
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
dss_core's opt-clocks is also missing dss_96m_fck, which is a DSS clock
present only on OMAP3430, and thus required on OMAP3430 to finish the
reset.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET and adds the dss_96m_fck
opt-clock for dss_core in OMAP3 HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2xxx HWMOD data currently contains two errors with DSS clocks:
- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
calculate timings
- dss_venc's interface and main clocks are wrong, causing VENC to fail
to start
These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.
HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.
This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core in OMAP2xxx
HWMOD data, fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 32aaeffbd4 (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
grep -L linux/module.h
arch/arm/mach-omap2/dsp.c
arch/arm/mach-omap2/mailbox.c
arch/arm/mach-omap2/omap-iommu.c
arch/arm/mach-omap2/smartreflex.c
Also check we either have export.h or module.h included
for the files exporting symbols:
$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
grep -L linux/export.h | xargs grep -L linux/module.h
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These files didn't exist at the time of the module.h split, and
so were not fixed by the commits on that baseline. Since they use
the EXPORT_SYMBOL and/or THIS_MODULE macros, they will need the
new export.h file included that provides them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
