Remove the redundant checking of netdev->netdev_ops as it will never be NULL.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
xid 0 was used as an indication of invalid xid before but now xid 0
can be used as a valid exchange i. This patch fixes the ddp completion
in fcp layer, i.e., in fc_fcp.c:fc_fcp_ddp_done() function, to make sure it
does not use xid 0 for indication of an invalid xid, instead, it now
uses use FC_XID_UNKNOWN for such indication.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A received Fibre Channel ELS PRLI request contains a bit that
indicates whether the remote port supports certain retry processing
sequences. The test for this bit was somehow coded to use multiply
instead of AND!
This case would apply only for target mode operation, and it is
unlikely to be noticed as an initiator.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When issuing a Cancel to the virtual fibre channel adapter,
the interface specifies a flags field for the client to indicate
what kind of error recovery is being performed. Fix up these
flags for terminate_rport_io to indicate an abort task set
rather than a target reset.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove a parameter to ibmvfc_init_host which is always set to
zero by all callers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Need to grab the host lock around the call to ibmvfc_link_down.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When processing the response to either a LUN reset,
target reset, or an abort task set, the ibmvfc driver needs to
treat as success receiving a response with a non-zero
status in the response IU along with a general transport
error with the FCP response code being zero. The VIOS
currently guarantees this cannot happen, but a future version
of VIOS may allow this to be returned, so ensure we handle
this response combination correctly for TMFs, as we already
do for SCSI commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This version fixes 64-bit modulo on 32-bit as well as inadvertent map
updates when TP was disabled.
Implement support for thin provisioning in scsi_debug. No actual memory
de-allocation is taking place. The intent is to emulate a thinly
provisioned storage device, not to be one.
There are four new module options:
- unmap_granularity specifies the granularity at which to track mapped
blocks (specified in number of logical blocks). 2048 (1 MB) is a
realistic value for disk arrays although some may have a finer
granularity.
- unmap_alignment specifies the first LBA which is naturally aligned on
an unmap_granularity boundary.
- unmap_max_desc specifies the maximum number of ranges that can be
unmapped using one UNMAP command. If this is 0, only WRITE SAME is
supported and UNMAP will cause a check condition.
- unmap_max_blocks specifies the maximum number of blocks that can be
unmapped using a single UNMAP command. Default is 0xffffffff.
These parameters are reported in the new and extended block limits VPD.
If unmap_granularity is specified the device is tagged as thin
provisioning capable in READ CAPACITY(16). A bitmap is allocated to
track whether blocks are mapped or not. A WRITE request will cause a
block to be mapped. So will WRITE SAME unless the UNMAP bit is set.
Blocks can be unmapped using either WRITE SAME or UNMAP. No accounting
is done to track partial blocks. This means that only whole blocks will
be marked free. This is how the array people tell me their firmwares
work.
GET LBA STATUS is also supported. This command reports whether a block
is mapped or not, and how long the adjoining mapped/unmapped extent is.
The block allocation bitmap can also be viewed from user space via:
/sys/bus/pseudo/drivers/scsi_debug/map
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add definitions for UNMAP, WRITE SAME{16,32} and GET LBA STATUS
commands.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Correct issues where the lower scsi-status would be improperly
cleared, instead, allow the midlayer to process the status after
the proper residual-count checks are performed. Finally,
validate firmware status flags prior to assigning values from the
FCP_RSP frame.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Michael Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code would not register FC4 nor FDMI information after a
logical tear-down of an VFC link. Code now triggers registration
date during processing of a 'Report ID Acquisition IOCB', which
is submitted after a FLOGI or FDISC completes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code discarded response-info field information and
assumed the command completed successfully without verifying the
target's status within the FCP_RSP packet.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In some case, the MPI and PHY versions when retrieved after the
Execute-FW mailbox-command are incorrect (255.255.255.255).
Instead, query the information after the check for firmware ready
is done in the abort ISP path.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The mailbox register values may assist in debugging efforts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
I was doing some large lun count testing with 2.6.31 and hit
a BUG_ON() in fc_timeout_deleted_rport(), and it seems like it
should have been just a matter of time before someone did.
It seems invalid to set port_state under lock, then expect it to
remain set after releasing the lock. Another thread called
fc_remote_port_add() when the lock was released, changing the
port_state.
This patch removes the BUG_ON and moves the test of the
port_state to inside the host_lock. It's been running for
several weeks now with no ill effect.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the Integrity check is done in scsi_io_completion it will
set error to -EILSEQ. However, at this point error is no longer
used, and blk_end_request_err has -EIO hardcoded.
It looks like there was just porting mistake with this patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=3e695f89c5debb735e4ff051e9e58d8fb4e95110
and we meant to send error upwards, so this patch changes the hard
coded EIO to the error variable.
I have only boot tested this patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for reset request from firmware for controllers
of st_shasta and st_yel type. Code adjustments necessary
for this change are also included.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The controllers of st_seq and st_vsc type can work
if only small dma buffer is available, with a reduced
firmware feature set. Add support for this case.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Errata:
Certain conditions on the scsi bus may casue the 53C1030 to incorrectly signal
a SCSI_DATA_UNDERRUN to the host.
Workaround 1:
For an Errata on LSI53C1030 When the length of request data
and transfer data are different with result of command (READ or VERIFY),
DID_SOFT_ERROR is set.
Workaround 2:
For potential trouble on LSI53C1030. It is checked whether the length of
request data is equal to the length of transfer and residual.
MEDIUM_ERROR is set by incorrect data.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
use the constant MEGASAS_RESET_WAIT_TIME when waiting for firmware
commands to complete (currently 3 minutes).
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current sense pointer is cast to a u32 pointer, which can truncate
on 64 bits. Fix by using unsigned long instead.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver will update the OS devices after adding and deleting the device
from FW. When driver receive add or delete AEN from FW, driver will
send the DCMD cmd to get the System PD list from FW. Then driver will
check if this device already in the OS: If add event and OS don't have
the device (but it is in the list), driver add the device to OS,
otherwise driver will not add. If remove event, driver will check the
list, if is not in the list, but OS have the device, driver will
remove the device.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a lock to the skinny firmware initialisation sequence to prevent
the two stage write being non atomic if multiple instances use it.
Add a flag to the driver shutdown sequence to prevent aen ioctls being
called after shutdown begins.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To increase the performance, megaraid sas driver added the IEEE SGE
support to support SAS2 controller.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MegaRAID SAS2 controller ioctl can't use 32 cmd for applications.
Driver need to divide different number of cmds to IO and application.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When OS issue inquiry, it will check driver's internal pd_list.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add system PDs to OS. Driver implemented the get_pd_list function to
get the system PD from FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the new megaraid sas 2 controller to the driver. megaraid sas2 is
LSI next generation SAS products. driver add the interface to support
this product.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
update the sysfs parameter to tell application driver support AEN poll
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add Poll_wait mechanism to SAS-2 MegaRAID SAS Linux driver. Driver
will wakeup poll after the driver get event from MegaRAID SAS FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the Tape drive fix to the megaraid_sas driver: If the command is
for the tape device, set the FW pthru timeout to the os layer timeout
value.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Bump version to 03.100.03.00
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) target resets are sending link change rate events with no link rate
change -> thus said the driver was modified so when there is no link rate
change, we don't need to call mpt2sas_transport_update_links nor
_scsih_ublock_io_device.
(2) There were changes made in _scsih_sas_topology_change_event_debug to
change the debug strings so they are more clear. Also the link rate change
information was added to display the new and previous link rate.
for the MPI2_EVENT_SAS_TOPOLOGY_CHANGE_LIST event when the ExpStatus is
set to zero, display "responding" instead of "unknown status".
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) Added new function _scsih_ir_shutdown. This function will issue the
MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED request via
MPI2_FUNCTION_RAID_ACTION. The function will wait 10 seconds for reply
message frame, then print out the ioc status and loginfo. This function is
only called when there are raid volumes present.
(2) Add shutdown callback in the struct pci_driver object scsih_driver. This
will be called only when the system is shutting down. From this function, we
will call _scsih_ir_shutdown mentioned above.
(3) Add support in _scsih_remove to call _scsih_ir_shutdown. The function
_scsih_remove will be called when the driver is unloaded (and system is
still running).
scsih internal command contex is added to send internal message frames
from mpt2sas_scsih.c.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When receiving the MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET event,
the driver will set the tm_busy flag in the sdev private host data, When
tm_busy flag is set, the driver will return SCSI_MLQUEUE_DEVICE_BUSY,
effectly freezing the IO to the device. The tm_busy flag is cleared with the
MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET event.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) EEDP(End to End data protection) was not working. This was due to not
setting EEDP BlockSize and Flags to little endian format in the message
frame.
(2) Some expander sysfs attributes were not getting set properly. The sas
format was not getting set due to endian issues with sas_format field in the
struct rep_manu_reply. Since sas_format was not set properly, the
component_vendor_id, component_revision_id, and component_id were not set.
(3) In _transport_smp_handler: we don't need to convert the smid from little
endian to cpu prior to calling mpt2sas_base_free_smid, because its allready
in cpu format. (4) Some loginfos and ioc status were not xonverted from
little endian to cpu.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
cpu_to_le64 when calculating the physical dma address. This will properly
handle endianess on big endian systems. The return value of this function
was changed from dma_addr_t to __le64. Remove the typecasting of u32 when
setting the SenseBufferLowAddress, since its already in __le32 format.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1 Its observed that the OS was sending request to the driver after it had been
put into blocking state, so the driver was modified to return
SCSI_MLQUEUE_DEVICE_BUSY.
2. Driver will return DID_TRANSPORT_DISRUPTED when sdev is haivng nexus loss.
This occurrs when sdev is blocked, between the
MPI2_EVENT_SAS_TOPO_RC_DELAY_NOT_RESPONDING and
MPI2_EVENT_SAS_TOPO_RC_TARG_NOT_RESPONDING events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver needs to retrieve the ioc facts prior to putting the controller
into READY state. The current design is calling ioc facts after putting the
controller into READY state, which means the driver is sending a diag reset
instead of message unit reset becuase the capability information is not yet
available.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
