There is no checks for dma mapping errors in mmc_spi.
Tha patch fixes that and by the way it adds dma_unmap_single(ones_dma)
that was left on a failure path mmc_spi_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device power usage counter is increased by pm_runtime_get_noresume
but isn't decreased in err_add_host error path.
Fix this issue by calling pm_runtime_put_noidle() in the error path to
restore the device's power usage counter.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: f5f17813ae ("mmc: sdhci-of-at91: add PM support)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit fixing the conversion of pxamci to slot-gpio API fixed the
inverted the logic of the read-only gpio. Unfortunately, the commit was
tested on a non-inverted gpio, and not on the inverted one. And the fix
did work partially, by luck.
This is the remaining missing part of the fix, trivial but still necessary.
Fixes: Fixes: 26d49fe719 ("mmc: pxamci: fix read-only gpio detection polarity")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Tested-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dHj5
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.5 rc1.
MMC core:
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik"
* tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: pwrseq_simple: Make reset-gpios optional to match doc
mmc: sdio_cis: fix unknown tuple for CISTPL_SDIO_STD
mmc: debugfs: correct wrong voltage value
mmc: tmio_mmc_dma: don't print invalid DMA cookie
mmc: core: Enable tuning according to the actual timing
mmc: mmci: support 8bit mode on the Nomadik
mmc: mmci: fix an ages old detection error
mmc: sd: limit SD card power limit according to cards capabilities
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
mmc: atmel: get rid of struct mci_dma_data
mmc: atmel-mci: restore dma on AVR32
avr32: wire up missing syscalls
avr32: wire up accept4 syscall
As struct mci_dma_data is now only used by AVR32, it is nothing but
pointless indirection. Replace it with struct dw_dma_slave in the
AVR32 platform code and with a void pointer elsewhere.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit ecb89f2f5f ("mmc: atmel-mci: remove compat for non DT board
when requesting dma chan") broke dma on AVR32 and any other boards not
using DT. This restores a fallback mechanism for such cases.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The tmio_mmc_start_dma_{rx,tx} function functions contain debug
code that prints the dma cookie among other things. However,
in case we fall back to PIO mode for some reason, the cookie
variable is never initialized, and gcc warns about this:
In file included from ../include/linux/printk.h:277:0,
from ../include/linux/kernel.h:13,
from ../include/linux/list.h:8,
from ../include/linux/kobject.h:20,
from ../include/linux/device.h:17,
from ../drivers/mmc/host/tmio_mmc_dma.c:13:
../drivers/mmc/host/tmio_mmc_dma.c: In function 'tmio_mmc_start_dma':
../include/linux/dynamic_debug.h:86:3: warning: 'cookie' may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
../drivers/mmc/host/tmio_mmc_dma.c:128:15: note: 'cookie' was declared here
dma_cookie_t cookie;
This modifies the dev_dbg() statements so we only print the cookie
when we are already in the DMA path.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 4956e10903 ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Cc: stable@vger.kernel.org
Fixes: 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik...")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The misc control register is 32bit wide, the used readw/writew
accessors only mainipulate the low 16bit of this register. It
currently doesn't matter as all the bit changed are located in
the lower half, but together with the u32 variable used to hold
the contents of the register it is seriously confusing.
Switch to 32bit accessors to avoid any future breakage.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Keep the quirk bits, as Tegra30 and Tegra114 host have different levels
of support for UHS-I modes and so need different spare bits to be set,
but change the logic to be positive.
Tegra210 needs a different tuning sequence than Tegra30+. Disable
UHS modes until support for this is properly added.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the UHS tuning sequence in a similar way to the one
contained in the TRM. It deviates in the way how to check if the tap
value is passing, by using the common Linux MMC function, which does
not only check for data CRC errors, but also if the received block
pattern is correct.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30 and up TRM states that this bit should always be
programmed to 0 by driver software.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow the the driver to change the clock supplied from the CAR directly,
minimizing the need to divide the clock inside the SDMMC module itself.
This allows for higher clock speeds than the default 48MHz supplied to
the module and is a prerequisite to support DDR signaling modes, where
the Tegra host needs to be run with a fixed internal divider of 2 for
data to be sampled correctly. (Tegra K1 TRM v03p chapter 29.7.1.1)
Also enable the broken preset value quirk as the preset values need to
be adapted to the changed clocking. While Tegra114+ allows this through
vendor registers, there is no such way for Tegra30. Takes the easy way
out and keep things consistent between the different SoC generations by
flagging the preset registers as unusable.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 52221610dd ("mmc: sdhci: Improve external VDD regulator
support"), for the VDD is supplied via external regulators, we ignore
the code to convert a VDD voltage request into one of the standard
SDHCI voltage levels, then program it in the SDHCI_POWER_CONTROL. This
brings two issues:
1. SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON quirk isn't handled properly any
more.
2. What's more, once SDHCI_POWER_ON bit is set, some controllers such
as the sdhci-pxav3 used in marvell berlin SoCs require the voltage
levels programming in the SDHCI_POWER_CONTROL register, even the VDD
is supplied by external regulator. So the host in marvell berlin SoCs
still works fine after the commit. However, commit 3cbc6123a9 ("mmc:
sdhci: Set SDHCI_POWER_ON with external vmmc") sets the SDHCI_POWER_ON
bit, this would make the host in marvell berlin SoCs won't work any
more with external vmmc.
This patch restores the behavior when setting VDD through external
regulator by moving the call of mmc_regulator_set_ocr() to the end
of sdhci_set_power() function.
After this patch, the sdcard on Marvell Berlin SoC boards work again.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 52221610dd ("mmc: sdhci: Improve external VDD ...")
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug
print") fixed one NULL pointer dereference but unfortunately introduced
another. "data" may be NULL if this is a command timeout for a command
without any data, so we should only use it if we're actually waiting for
data.
Fixes: bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print")
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no primary handler is specified for threaded_irq then a
default one is assigned which always returns IRQ_WAKE_THREAD.
This handler requires the IRQF_ONESHOT, because the source of
interrupt is not disabled
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there are too many error logs shown when use CMD21/CMD19 to do tune,
and it will appear at each resume time, print out so many logs to the
uart console cost too mush time. so change it to dev_dbg.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The version 3.00 SDHCI spec. was a bit unclear about the
required data alignment for 64-bit DMA, whereas the version
4.10 spec. uses different language and indicates that only
4-byte alignment is required rather than the 8-byte alignment
currently implemented. That make no difference to SD and EMMC
which invariably transfer data in sector-aligned blocks.
However with SDIO, it results in using more DMA descriptors
than necessary. Theoretically that slows DMA slightly although
DMA is not the limiting factor for throughput, so there is no
discernable impact on performance. Nevertheless, the driver
should follw the spec unless there is good reason not to, so
this patch corrects the alignment criterion.
There is a more complicated criterion for the DMA descriptor
table itself. However the table is allocated by dma_alloc_coherent()
which allocates pages (i.e. aligned to a page boundary).
For simplicity just check it is 8-byte aligned, but add a comment
that some Intel controllers actually require 8-byte alignment
even when using 32-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI has built-in DMA called ADMA2. ADMA2 uses a descriptor
table to define DMA scatter-gather. Each desciptor can specify
a data length up to 65536 bytes, however the length field is
only 16-bits so zero means 65536. Consequently, putting zero
when the size is zero must not be allowed. This patch fixes
one case where zero data length could be set inadvertently.
The problem happens because unaligned data gets split and the
code did not consider that the remaining aligned portion might
be zero length. That case really only happens for SDIO because
SD and eMMC cards transfer blocks that are invariably sector-
aligned. For SDIO, access to function registers is done by
data transfer (CMD53) when the register is bigger than 1 byte.
Generally registers are 4 bytes but 2-byte registers are possible.
So DMA of 4 bytes or less can happen. When 32-bit DMA is used,
the data alignment must be 4, so 4-byte transfers won't casue a
problem, but a 2-byte transfer could. However with the introduction
of 64-bit DMA, the data alignment for 64-bit DMA was made 8 bytes,
so all 4-byte transfers not on 8-byte boundaries get "split" into
a 4-byte chunk and a 0-byte chunk, thereby hitting the bug.
In fact, a closer look at the SDHCI specs indicates that only the
descriptor table requires 8-byte alignment for 64-bit DMA. That
will be dealt with in a separate patch, but the potential for a
2-byte access remains, so this fix is needed anyway.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver may not be able to set the power correctly but that
is not a reason to BUG().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default. Change it to the standard default
50 Ohm value.
The patch applies to v4.2+ except the file name changed. It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are no in-kernel users of the MVSDIO platform data method
(instantiating from a board file) so just delete this code and
make this a DT-only driver. We depend on OF and check that we have
an OF node in probe().
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform data struct is only used inside the MVSDIO driver,
nowhere else in the entire kernel. Move the struct into the
driver and delete the external header.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
u32 vvn;
vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
if (vvn == VENDOR_V_22)
host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
if (vvn > VENDOR_V_22)
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd22 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The atmci_convert_chksize() function is no more valid for controller
version 0x600 due to the introduction of '2 data' chunk size.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
atmel-mci-regs.h is only included in atmel-mci.c so move its content in
the driver and do some cleanup in these definitions to remove checkpatch
errors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Here we use '|=' to set the tuning-step, but before that, we should
clear the tuning-step, otherwise we could got the wrong setting.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:
../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_tx :
^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_rx;
This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.
The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a trivial patch which fixes printed strings split across two
or more lines in the source. I tried to grep for some error output*,
but I couldn't find it easily because it was broken across multiple
lines. This patch makes my life easier.
* in particular "Timeout waiting for hardware interrupt."
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data in the SoC description structures is static and can therefore
reside in read-only memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add runtime PM support and use runtime_force_suspend|resume() for system
PM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver will not probe without valid DMA channels so no need to check
if they are valid when the module is removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Though the mmc core driver should/will continue to support the legacy
"enable-sdio-wakeup" property to enable SDIO as the wakeup source, we
need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "enable-sdio-wakeup" property.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/mtk-sd.c: In function ‘get_best_delay’:
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.start’ is used uninitialized in this function
drivers/mmc/host/mtk-sd.c:1284: warning: ‘delay_phase.maxlen’ is used uninitialized in this function
If delay is zero, these fields are indeed not initialized.
Let the compiler preinitialize the whole struct to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit converting pxamci to slot-gpio API inverted the logic of the
read-only gpio. Fix it by inverting the logic again.
Fixes: fd546ee6a7 ("mmc: pxamci: fix card detect with slot-gpio API")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
When card is running with DDR mode, dwmmc needs to set DDR_REG bit at
UHS_REG register.
Before this patch, dwmmc controller doesn't consider this.
If this patch is not applied, CRC or other error shoulds be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to DesignWare DoC file, CardThreshold bit should be
bit[27:16].
So it's correct to use (0xFFF << 16), not (0x1FFF << 16).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "host->dms->ch" pointer is NULL here so we can't use it to print the
error message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
