Pull x86 EFI changes from Ingo Molnar:
"Main changes:
- Add support for earlyprintk=efi which uses the EFI framebuffer.
Very useful for debugging boot problems.
- EFI stub support for large memory maps (more than 128 entries)
- EFI ARM support - this was mostly done by generalizing x86 <-> ARM
platform differences, such as by moving x86 EFI code into
drivers/firmware/efi/ and sharing it with ARM.
- Documentation updates
- misc fixes"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/efi: Add EFI framebuffer earlyprintk support
boot, efi: Remove redundant memset()
x86/efi: Fix config_table_type array termination
x86 efi: bugfix interrupt disabling sequence
x86: EFI stub support for large memory maps
efi: resolve warnings found on ARM compile
efi: Fix types in EFI calls to match EFI function definitions.
efi: Renames in handle_cmdline_files() to complete generalization.
efi: Generalize handle_ramdisks() and rename to handle_cmdline_files().
efi: Allow efi_free() to be called with size of 0
efi: use efi_get_memory_map() to get final map for x86
efi: generalize efi_get_memory_map()
efi: Rename __get_map() to efi_get_memory_map()
efi: Move unicode to ASCII conversion to shared function.
efi: Generalize relocate_kernel() for use by other architectures.
efi: Move relocate_kernel() to shared file.
efi: Enforce minimum alignment of 1 page on allocations.
efi: Rename memory allocation/free functions
efi: Add system table pointer argument to shared functions.
efi: Move common EFI stub code from x86 arch code to common location
...
Pull x86 cleanups from Ingo Molnar:
"Two small cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, msr: Use file_inode(), not f_mapping->host
x86: mkpiggy.c: Explicitly close the output file
When a function is used in more than one file it may not be possible
to immediately tell from context what the intended meaning is. As
such, it is more important that the naming be self-evident. Thus,
change get_flags() to get_cpuflags().
For consistency, change check_flags() to check_cpuflags() even though
it is only used in cpucheck.c.
Link: http://lkml.kernel.org/r/1381450698-28710-2-git-send-email-keescook@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Counts available alignment positions across all e820 maps, and chooses
one randomly for the new kernel base address, making sure not to collide
with unsafe memory areas.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/1381450698-28710-5-git-send-email-keescook@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Adds potential sources of randomness: RDRAND, RDTSC, or the i8254.
This moves the pre-alternatives inline rdrand function into the header so
both pieces of code can use it. Availability of RDRAND is then controlled
by CONFIG_ARCH_RANDOM, if someone wants to disable it even for kASLR.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/1381450698-28710-4-git-send-email-keescook@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This allows decompress_kernel to return a new location for the kernel to
be relocated to. Additionally, enforces CONFIG_PHYSICAL_START as the
minimum relocation position when building with CONFIG_RELOCATABLE.
With CONFIG_RANDOMIZE_BASE set, the choose_kernel_location routine
will select a new location to decompress the kernel, though here it is
presently a no-op. The kernel command line option "nokaslr" is introduced
to bypass these routines.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/1381450698-28710-3-git-send-email-keescook@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Refactor the CPU flags handling out of the cpucheck routines so that
they can be reused by the future ASLR routines (in order to detect CPU
features like RDRAND and RDTSC).
This reworks has_eflag() and has_fpu() to be used on both 32-bit and
64-bit, and refactors the calls to cpuid to make them PIC-safe on 32-bit.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/1381450698-28710-2-git-send-email-keescook@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Even though the resource is released when the application is closed or
when returned from main function, modify the code to make it obvious,
and to keep static analysis tools from complaining.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Link: http://lkml.kernel.org/r/1381184219-10985-1-git-send-email-geyslan@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The problem in efi_main was that the idt was cleared before the
interrupts were disabled.
The UEFI spec states that interrupts aren't used so this shouldn't be
too much of a problem. Peripherals however don't necessarily know about
this and thus might cause interrupts to happen anyway. Even if
ExitBootServices() has been called.
This means there is a risk of an interrupt being triggered while the IDT
register is nullified and the interrupt bit hasn't been cleared,
allowing for a triple fault.
This patch disables the interrupt flag, while leaving the existing IDT
in place. The CPU won't care about the IDT at all as long as the
interrupt bit is off, so it's safe to leave it in place as nothing will
ever happen to it.
[ Removed the now unused 'idt' variable - Matt ]
Signed-off-by: Bart Kuivenhoven <bemk@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This patch fixes a problem with EFI memory maps larger than 128 entries
when booting using the EFI stub, which results in overflowing e820_map
in boot_params and an eventual halt when checking the map size in
sanitize_e820_map().
If the number of map entries is greater than what can fit in e820_map,
add the extra entries to the setup_data list using type SETUP_E820_EXT.
These extra entries are then picked up when the setup_data list is
parsed in parse_e820_ext().
Signed-off-by: Linn Crosetto <linn@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
When building on x86, the final image building step always emits stats
to stderr, even though this information is neither a warning nor an error:
BUILD arch/x86/boot/bzImage
Setup is 16188 bytes (padded to 16384 bytes).
System is 6368 kB
CRC cbe50c61
Validating automated builds would be cleaner if stderr did not have to
filter out these lines. Instead, change how tools/build is called, and
make the zoffset header unconditional, and write to a specified file
instead of to stdout, which can then be used for statistics, leaving
stderr open for legitimate warnings and errors, like the output from
die().
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130906181532.GA31260@www.outflux.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The handle_cmdline_files now takes the option to handle as a string,
and returns the loaded data through parameters, rather than taking
an x86 specific setup_header structure. For ARM, this will be used
to load a device tree blob in addition to initrd images.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Acked-by: Mark Salter <msalter@redhat.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Make efi_free() safely callable with size of 0, similar to free() being
callable with NULL pointers, and do nothing in that case.
Remove size checks that this makes redundant. This also avoids some
size checks in the ARM EFI stub code that will be added as well.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Replace the open-coded memory map getting with the
efi_get_memory_map() that is now general enough to use.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Move the open-coded conversion to a shared function for
use by all architectures. Change the allocation to prefer
a high address for ARM, as this is required to avoid conflicts
with reserved regions in low memory. We don't know the specifics
of these regions until after we process the command line and
device tree.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Rename relocate_kernel() to efi_relocate_kernel(), and take
parameters rather than x86 specific structure. Add max_addr
argument as for ARM we have some address constraints that we
need to enforce when relocating the kernel. Add alloc_size
parameter for use by ARM64 which uses an uncompressed kernel,
and needs to allocate space for BSS.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The relocate_kernel() function will be generalized and used
by all architectures, as they all have similar requirements.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Rename them to be more similar, as low_free() could be used to free
memory allocated by both high_alloc() and low_alloc().
high_alloc() -> efi_high_alloc()
low_alloc() -> efi_low_alloc()
low_free() -> efi_free()
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Acked-by: Mark Salter <msalter@redhat.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Add system table pointer argument to shared EFI stub related functions
so they no longer use a global system table pointer as they did when part
of eboot.c. For the ARM EFI stub this allows us to avoid global
variables completely and thereby not have to deal with GOT fixups.
Not having the EFI stub fixup its GOT, which is shared with the
decompressor, simplifies the relocating of the zImage to a
bootable address.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
No code changes made, just moving functions and #define from x86 arch
directory to common location. Code is shared using #include, similar
to how decompression code is shared among architectures.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Acked-by: Mark Salter <msalter@redhat.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The x86/AMD64 EFI stubs must use a call wrapper to convert between
the Linux and EFI ABIs, so void pointers are sufficient. For ARM,
the ABIs are compatible, so we can directly invoke the function
pointers. The functions that are used by the ARM stub are updated
to match the EFI definitions.
Also add some EFI types used by EFI functions.
Signed-off-by: Roy Franz <roy.franz@linaro.org>
Acked-by: Mark Salter <msalter@redhat.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Pull x86 relocation changes from Ingo Molnar:
"This tree contains a single change, ELF relocation handling in C - one
of the kernel randomization patches that makes sense even without
randomization present upstream"
* 'x86-kaslr-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, relocs: Move ELF relocation handling to C
Pull tiny x86 boot cleanups from Ingo Molnar.
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix a sanity check in printf.c
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Fix warning due to undeclared strlen()
Prior to 9b706aee7d ("x86: trivial printk optimizations") this was
36 because it had 26 characters and 10 digits but now it's just
16 hex digits so the sanity check needs updated.
This function is always called with a valid "base" so it doesn't
make a difference to how the kernel works, it's just a cleanup.
Reported-by: Alexey Petrenko <alexey.petrenko@oracle.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Below is a patch that fixes sparse error
"arch/x86/boot/string.c:119:8: warning: symbol 'strlen' was not
declared." by declaring it in arch/x86/boot/boot.h.
Signed-off-by: Fred Chen <fchen@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1376417580-11554-1-git-send-email-fchen@linux.vnet.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Moves the relocation handling into C, after decompression. This requires
that the decompressed size is passed to the decompression routine as
well so that relocations can be found. Only kernels that need relocation
support will use the code (currently just x86_32), but this is laying
the ground work for 64-bit using it in support of KASLR.
Based on work by Neill Clift and Michael Davidson.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130708161517.GA4832@www.outflux.net
Acked-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull x86 mm changes from Ingo Molnar:
"Misc improvements:
- Fix /proc/mtrr reporting
- Fix ioremap printout
- Remove the unused pvclock fixmap entry on 32-bit
- misc cleanups"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioremap: Correct function name output
x86: Fix /proc/mtrr with base/size more than 44bits
ix86: Don't waste fixmap entries
x86/mm: Drop unneeded include <asm/*pgtable, page*_types.h>
x86_64: Correct phys_addr in cleanup_highmap comment
Pull x86 EFI changes from Ingo Molnar:
"Two fixes that should in principle increase robustness of our
interaction with the EFI firmware, and a cleanup"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: retry ExitBootServices() on failure
efi: Convert runtime services function ptrs
UEFI: Don't pass boot services regions to SetVirtualAddressMap()
ExitBootServices is absolutely supposed to return a failure if any
ExitBootServices event handler changes the memory map. Basically the
get_map loop should run again if ExitBootServices returns an error the
first time. I would say it would be fair that if ExitBootServices gives
an error the second time then Linux would be fine in returning control
back to BIOS.
The second change is the following line:
again:
size += sizeof(*mem_map) * 2;
Originally you were incrementing it by the size of one memory map entry.
The issue here is all related to the low_alloc routine you are using.
In this routine you are making allocations to get the memory map itself.
Doing this allocation or allocations can affect the memory map by more
than one record.
[ mfleming - changelog, code style ]
Signed-off-by: Zach Bobroff <zacharyb@ami.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This patch reworks the UEFI anti-bricking code, including an effective
reversion of cc5a080c and 31ff2f20. It turns out that calling
QueryVariableInfo() from boot services results in some firmware
implementations jumping to physical addresses even after entering virtual
mode, so until we have 1:1 mappings for UEFI runtime space this isn't
going to work so well.
Reverting these gets us back to the situation where we'd refuse to create
variables on some systems because they classify deleted variables as "used"
until the firmware triggers a garbage collection run, which they won't do
until they reach a lower threshold. This results in it being impossible to
install a bootloader, which is unhelpful.
Feedback from Samsung indicates that the firmware doesn't need more than
5KB of storage space for its own purposes, so that seems like a reasonable
threshold. However, there's still no guarantee that a platform will attempt
garbage collection merely because it drops below this threshold. It seems
that this is often only triggered if an attempt to write generates a
genuine EFI_OUT_OF_RESOURCES error. We can force that by attempting to
create a variable larger than the remaining space. This should fail, but if
it somehow succeeds we can then immediately delete it.
I've tested this on the UEFI machines I have available, but I don't have
a Samsung and so can't verify that it avoids the bricking problem.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Lee, Chun-Y <jlee@suse.com> [ dummy variable cleanup ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
arch/x86/boot/compressed/head_64.S includes <asm/pgtable_types.h> and
<asm/page_types.h> but it doesn't look like it needs them. So remove them.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Link: http://lkml.kernel.org/r/5191FAE2.4020403@cn.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 cleanups from Ingo Molnar:
"Misc smaller cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/lib: Fix spelling, put space between a numeral and its units
x86/lib: Fix spelling in the comments
x86, quirks: Shut-up a long-standing gcc warning
x86, msr: Unify variable names
x86-64, docs, mm: Add vsyscall range to virtual address space layout
x86: Drop KERNEL_IMAGE_START
x86_64: Use __BOOT_DS instead_of __KERNEL_DS for safety
on some Apple machines because they implement EFI spec 1.10, which
doesn't provide a QueryVariableInfo() runtime function and the logic
used to check for the existence of that function was insufficient.
Fix from Josh Boyer.
* The anti-bricking algorithm also introduced a compiler warning on
32-bit. Fix from Borislav Petkov.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=l/fT
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' into x86/urgent
* The EFI variable anti-bricking algorithm merged in -rc8 broke booting
on some Apple machines because they implement EFI spec 1.10, which
doesn't provide a QueryVariableInfo() runtime function and the logic
used to check for the existence of that function was insufficient.
Fix from Josh Boyer.
* The anti-bricking algorithm also introduced a compiler warning on
32-bit. Fix from Borislav Petkov.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We need to check the runtime sys_table for the EFI version the firmware
specifies instead of just checking for a NULL QueryVariableInfo. Older
implementations of EFI don't have QueryVariableInfo but the runtime is
a smaller structure, so the pointer to it may be pointing off into garbage.
This is apparently the case with several Apple firmwares that support EFI
1.10, and the current check causes them to no longer boot. Fix based on
a suggestion from Matthew Garrett.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Fix this:
arch/x86/boot/compressed/eboot.c: In function ‘setup_efi_vars’:
arch/x86/boot/compressed/eboot.c:269:2: warning: passing argument 1 of ‘efi_call_phys’ makes pointer from integer without a cast [enabled by default]
In file included from arch/x86/boot/compressed/eboot.c:12:0:
/w/kernel/linux/arch/x86/include/asm/efi.h:8:33: note: expected ‘void *’ but argument is of type ‘long unsigned int’
after cc5a080c5d ("efi: Pass boot services variable info to runtime
code").
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Matt Fleming (1):
x86, efivars: firmware bug workarounds should be in platform
code
Matthew Garrett (3):
Move utf16 functions to kernel core and rename
efi: Pass boot services variable info to runtime code
efi: Distinguish between "remaining space" and actually used
space
Richard Weinberger (2):
x86,efi: Check max_size only if it is non-zero.
x86,efi: Implement efi_no_storage_paranoia parameter
Sergey Vlasov (2):
x86/Kconfig: Make EFI select UCS2_STRING
efi: Export efi_query_variable_store() for efivars.ko
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
EFI variables can be flagged as being accessible only within boot services.
This makes it awkward for us to figure out how much space they use at
runtime. In theory we could figure this out by simply comparing the results
from QueryVariableInfo() to the space used by all of our variables, but
that fails if the platform doesn't garbage collect on every boot. Thankfully,
calling QueryVariableInfo() while still inside boot services gives a more
reliable answer. This patch passes that information from the EFI boot stub
up to the efi platform code.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
eboot.o and efi_stub_$(BITS).o didn't get added to "targets", and hence
their .cmd files don't get included by the build machinery, leading to
the files always getting rebuilt.
Rather than adding the two files individually, take the opportunity and
add $(VMLINUX_OBJS) to "targets" instead, thus allowing the assignment
at the top of the file to be shrunk quite a bit.
At the same time, remove a pointless flags override line - the variable
assigned to was misspelled anyway, and the options added are
meaningless for assembly sources.
[ hpa: the patch is not minimal, but I am taking it for -urgent anyway
since the excess impact of the patch seems to be small enough. ]
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Link: http://lkml.kernel.org/r/515C5D2502000078000CA6AD@nat28.tlf.novell.com
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In startup_32, the running code still uses the initial GDT
located in setup. Thus, __BOOT_DS is preferred. Currently
__KERNEL_DS is lucky to equal to __BOOT_DS, but this is
not always a safe way.
Signed-off-by: Lans Zhang <lans.zhang2008@gmail.com>
Link: http://lkml.kernel.org/r/51300267.6000008@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull x86/EFI changes from Peter Anvin:
- Improve the initrd handling in the EFI boot stub by allowing forward
slashes in the pathname - from Chun-Yi Lee.
- Cleanup code duplication in the EFI mixed kernel/firmware code - from
Satoru Takeuchi.
- efivarfs bug fixes for more strict filename validation, with lots of
input from Al Viro.
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove duplicate code in setup_arch() by using, efi_is_native()
efivarfs: guid part of filenames are case-insensitive
efivarfs: Validate filenames much more aggressively
efivarfs: Use sizeof() instead of magic number
x86, efi: Allow slash in file path of initrd
Pull x86 mm changes from Peter Anvin:
"This is a huge set of several partly interrelated (and concurrently
developed) changes, which is why the branch history is messier than
one would like.
The *really* big items are two humonguous patchsets mostly developed
by Yinghai Lu at my request, which completely revamps the way we
create initial page tables. In particular, rather than estimating how
much memory we will need for page tables and then build them into that
memory -- a calculation that has shown to be incredibly fragile -- we
now build them (on 64 bits) with the aid of a "pseudo-linear mode" --
a #PF handler which creates temporary page tables on demand.
This has several advantages:
1. It makes it much easier to support things that need access to data
very early (a followon patchset uses this to load microcode way
early in the kernel startup).
2. It allows the kernel and all the kernel data objects to be invoked
from above the 4 GB limit. This allows kdump to work on very large
systems.
3. It greatly reduces the difference between Xen and native (Xen's
equivalent of the #PF handler are the temporary page tables created
by the domain builder), eliminating a bunch of fragile hooks.
The patch series also gets us a bit closer to W^X.
Additional work in this pull is the 64-bit get_user() work which you
were also involved with, and a bunch of cleanups/speedups to
__phys_addr()/__pa()."
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (105 commits)
x86, mm: Move reserving low memory later in initialization
x86, doc: Clarify the use of asm("%edx") in uaccess.h
x86, mm: Redesign get_user with a __builtin_choose_expr hack
x86: Be consistent with data size in getuser.S
x86, mm: Use a bitfield to mask nuisance get_user() warnings
x86/kvm: Fix compile warning in kvm_register_steal_time()
x86-32: Add support for 64bit get_user()
x86-32, mm: Remove reference to alloc_remap()
x86-32, mm: Remove reference to resume_map_numa_kva()
x86-32, mm: Rip out x86_32 NUMA remapping code
x86/numa: Use __pa_nodebug() instead
x86: Don't panic if can not alloc buffer for swiotlb
mm: Add alloc_bootmem_low_pages_nopanic()
x86, 64bit, mm: hibernate use generic mapping_init
x86, 64bit, mm: Mark data/bss/brk to nx
x86: Merge early kernel reserve for 32bit and 64bit
x86: Add Crash kernel low reservation
x86, kdump: Remove crashkernel range find limit for 64bit
memblock: Add memblock_mem_size()
x86, boot: Not need to check setup_header version for setup_data
...
Pull x86 bootup changes from Ingo Molnar:
"Deal with bootloaders which fail to initialize unknown fields in
boot_params to zero, by sanitizing boot params passed in.
This unbreaks versions of kexec-utils. Other bootloaders do not
appear to show sensitivity to this change, but it's a possibility for
breakage nevertheless."
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Sanitize boot_params if not zeroed on creation
When initrd file didn't put at the same place with stub kernel, we
need give the file path of initrd, but need use backslash to separate
directory and file. It's not friendly to unix/linux user, and not so
intuitive for bootloader forward paramters to efi stub kernel by
chainloading.
This patch add support to handle_ramdisks for allow slash in file path
of initrd, it convert slash to backlash when parsing path.
In additional, this patch also separates print code of efi_char16_t from
efi_printk, and print out the path/filename of initrd when failed to open
initrd file. It's good for debug and discover typo.
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRCBrMAAoJEC84WcCNIz1VTdcP/2u3ZqohOKJAwwMkyzB3nkrQ
1mhxKGFDitAAvGQQCOq3oIMgBZHOevKznH3hZtX+hxBxwu7AuNL+qw6Baz8GYZpz
guFvAZjm2JX2ko1PgtNvPUFZ1krw7TObLW2YstTWhSDoOlRK5kqmA+idaJf1aHDe
/cwV6Mr6u5N/egyBBcQI1ydKLA6ogmx1zfDsS9b2Vzavw168RGqfrpH3ybcokYND
/E2NtcRVZagBw35eZHEDNKcoPt5z+skCA4nJyA6bLbxMsq51ZKaK0PKKaA8vd70s
6Pc7d6zkQG/ZmaxrRfsdQUAYfJRJq/cpeTgS4YurkZB0r0gdxk6I86vYlg+xXi0X
eqLAkUJJJasVY/1NK/c2vsJ03W9wDYkd2IJpUcl7rWz7Aa/RurY32QmT3SnLop7m
Tzj3CgXAu/RH8FyMNMWpI85tOis7OcMUfrjmnxquQdCZpLXSsh7Rf5EgBRiv9xhH
txDOX3y21Jnv2A5efAVWm5EbyI204Wq2nVDzSu0xTMXWkzdBg+/OeyYfzV0Sdguf
3/MzYTn7mVXh/EZtnvsTyNjgvVxzpXW6mAf+ne9iJaC8MUJVIeSjB7xzSfuHXUBU
aUc9OnbkHRJCdVSeKqZbLwO3X5mTXqmDMfIcRle3BPewvZ9pOEv8VrGgsNxh9ixW
JaCpiTdxJDFtz6cLVsNa
=QrJx
-----END PGP SIGNATURE-----
Merge tag 'efi-for-3.8' into x86/efi
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now 64bit entry is fixed on 0x200, can not be changed anymore.
Update the comments to reflect that.
Also put info about it in boot.txt
-v2: fix some grammar error
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-27-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
xloadflags bit 1 indicates that we can load the kernel and all data
structures above 4G; it is set if kernel is relocatable and 64bit.
bootloader will check if xloadflags bit 1 is set to decide if
it could load ramdisk and kernel high above 4G.
bootloader will fill value to ext_ramdisk_image/size for high 32bits
when it load ramdisk above 4G.
kernel use get_ramdisk_image/size to use ext_ramdisk_image/size to get
right positon for ramdisk.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Rob Landley <rob@landley.net>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
commit 08da5a2ca
x86_64: Early segment setup for VT
sets up LDT and TR into a valid state in order to speed up boot
decompression under VT.
Those code are put in code64, and it is using GDT that is only
loaded from code32 path.
That breaks booting with 64bit bootloader that does not go through
code32 path and jump to startup_64 directly, and it has different
GDT.
Move those lines into code32 after their GDT is loaded.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-21-git-send-email-yinghai@kernel.org
Cc: Zachary Amsden <zamsden@gmail.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We need to move some code to 32bit section in following patch:
x86, boot: Move lldt/ltr out of 64bit code section
but that will push startup_64 down from 0x200.
According to hpa, we can not change startup_64 position and that
is an ABI.
We could move function verify_cpu and no_longmode down, because
verify_cpu is used via function call and no_longmode will not
return, then we don't need to add extra code for jumping back.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-20-git-send-email-yinghai@kernel.org
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
boot/compressed/misc.c is used for bzImage in 64bit and 32bit, and
cmd_line_ptr could point to buffer that is above 4g, cmd_line_ptr
should be 64bit otherwise high 32bit will be capped out.
So need to change data type to unsigned long, that will be 64bit get
correct address of command line buffer.
And it is still ok with 32bit bzImage, because unsigned long on 32bit kernel
is still 32bit.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-19-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
cmdline.c::__cmdline_find_option... are shared between 16-bit setup code
and 32/64 bit decompressor code.
for 32/64 only path via kexec, we should not check if ptr is less 1M.
as those cmdline could be put above 1M, or even 4G.
Move out accessible checking out of __cmdline_find_option()
So decompressor in misc.c can parse cmdline correctly.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-18-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add an accessor function for the command line address.
Later we will add support for holding a 64-bit address via ext_cmd_line_ptr.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-17-git-send-email-yinghai@kernel.org
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It looks like the original commit that copied the rom contents from
efi always copied the rom, and the fixup in setup_efi_pci from commit
886d751a2e ("x86, efi: correct precedence of operators in
setup_efi_pci") broke that.
This resulted in macbook pro's no longer finding the rom images, and
thus not being able to use the radeon card any more.
The solution is to just remove the check for now, and always copy the
rom if available.
Reported-by: Vitaly Budovski <vbudovski+news@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Use the new sentinel field to detect bootloaders which fail to follow
protocol and don't initialize fields in struct boot_params that they
do not explicitly initialize to zero.
Based on an original patch and research by Yinghai Lu.
Changed by hpa to be invoked both in the decompression path and in the
kernel proper; the latter for the case where a bootloader takes over
decompression.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We have historically hard-coded entry points in head.S just so it's easy
to build the executable/bzImage headers with references to them.
Unfortunately, this leads to boot loaders abusing these "known" addresses
even when they are *explicitly* told that they "should look at the ELF
header to find this address, as it may change in the future". And even
when the address in question *has* actually been changed in the past,
without fanfare or thought to compatibility.
Thus we have bootloaders doing stunningly broken things like jumping
to offset 0x200 in the kernel startup code in 64-bit mode, *hoping*
that startup_64 is still there (it has moved at least once
before). And hoping that it's actually a 64-bit kernel despite the
fact that we don't give them any indication of that fact.
This patch should hopefully remove the temptation to abuse internal
addresses in future, where sternly worded comments have not sufficed.
Instead of having hard-coded addresses and saying "please don't abuse
these", we actually pull the addresses out of the ELF payload into
zoffset.h, and make build.c shove them back into the right places in
the bzImage header.
Rather than including zoffset.h into build.c and thus having to rebuild
the tool for every kernel build, we parse it instead. The parsing code
is small and simple.
This patch doesn't actually move any of the interesting entry points, so
any offending bootloader will still continue to "work" after this patch
is applied. For some version of "work" which includes jumping into the
compressed payload and crashing, if the bzImage it's given is a 32-bit
kernel. No change there then.
[ hpa: some of the issues in the description are addressed or
retconned by the 2.12 boot protocol. This patch has been edited to
only remove fixed addresses that were *not* thus retconned. ]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
The 'Attributes' argument to pci->Attributes() function is 64-bit. So
when invoking in 32-bit mode it takes two registers, not just one.
This fixes memory corruption when booting via the 32-bit EFI boot stub.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
If the bootloader calls the EFI handover entry point as a standard function
call, then it'll have a return address on the stack. We need to pop that
before calling efi_main(), or the arguments will all be out of position on
the stack.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
When booting under OVMF we have precisely one GOP device, and it
implements the ConOut protocol.
We break out of the loop when we look at it... and then promptly abort
because 'first_gop' never gets set. We should set first_gop *before*
breaking out of the loop. Yes, it doesn't really mean "first" any more,
but that doesn't matter. It's only a flag to indicate that a suitable
GOP was found.
In fact, we'd do just as well to initialise 'width' to zero in this
function, then just check *that* instead of first_gop. But I'll do the
minimal fix for now (and for stable@).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
Fix four similar build warnings on 32-bit (casts between different
size pointers and integers).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Stefan Hasko <hasko.stevo@gmail.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
With the current code, the condition in the if() doesn't make much sense due to
precedence of operators.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Link: http://lkml.kernel.org/r/1356030701-16284-25-git-send-email-sasha.levin@oracle.com
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
EFI provides support for providing PCI ROMs via means other than the ROM
BAR. This support vanishes after we've exited boot services, so add support
for stashing copies of the ROMs in setup_data if they're not otherwise
available.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Building for Athlon/Duron/K7 results in the following build error,
arch/x86/boot/compressed/eboot.o: In function `__constant_memcpy3d':
eboot.c:(.text+0x385): undefined reference to `_mmx_memcpy'
arch/x86/boot/compressed/eboot.o: In function `efi_main':
eboot.c:(.text+0x1a22): undefined reference to `_mmx_memcpy'
because the boot stub code doesn't link with the kernel proper, and
therefore doesn't have access to the 3DNow version of memcpy. So,
follow the example of misc.c and #undef memcpy so that we use the
version provided by misc.c.
See https://bugzilla.kernel.org/show_bug.cgi?id=50391
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Ryan Underwood <nemesis@icequake.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Commit 2e064b1 (x86, efi: Fix issue of overlapping .reloc section for
EFI_STUB) removed a dummy reloc added by commit 291f363 (x86, efi: EFI
boot stub support), but forgot to remove the dummy long used by that
reloc.
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Commit 77d1a49995 ("x86, boot: make
symbols from the main vmlinux available") removed all traces of
offsets.h from the tree. Remove its entries in dontdiff and x86/boot's
.gitignore file too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h. But commit abbf1590de ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.
This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.
It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Partition the header include path flags into two sets, one for kernelspace
builds and one for userspace builds.
Add the following directories to build after the ordinary include directories
so that #include will pick up the UAPI header directly if the kernel header
has been moved there.
The userspace set (represented by the USERINCLUDE make variable) contains:
-I $(srctree)/arch/$(hdr-arch)/include/uapi
-I arch/$(hdr-arch)/include/generated/uapi
-I $(srctree)/include/uapi
-I include/generated/uapi
-include $(srctree)/include/linux/kconfig.h
and the kernelspace set (represented by the LINUXINCLUDE make variable)
contains:
-I $(srctree)/arch/$(hdr-arch)/include
-I arch/$(hdr-arch)/include/generated
-I $(srctree)/include
-I include --- if not building in the source tree
plus everything in the USERINCLUDE set.
Then use USERINCLUDE in building the x86 boot code.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Pull x86/EFI changes from Ingo Molnar:
"EFI loader robustness enhancements plus smaller fixes"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Fix the ACPI BGRT driver for images located in EFI boot services memory
efi: Add a function to look up existing IO memory mappings
efi: Defer freeing boot services memory until after ACPI init
x86, EFI: Calculate the EFI framebuffer size instead of trusting the firmware
efifb: Skip DMI checks if the bootloader knows what it's doing
efi: initialize efi.runtime_version to make query_variable_info/update_capsule workable
efi: Build EFI stub with EFI-appropriate options
X86: Improve GOP detection in the EFI boot stub
Seth Forshee reported that his system was reporting that the EFI framebuffer
stretched from 0x90010000-0xb0010000 despite the GPU's BAR only covering
0x90000000-0x9ffffff. It's safer to calculate this value from the pixel
stride and screen height (values we already depend on) rather than face
potential problems with resource allocation later on.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The majority of the DMI checks in efifb are for cases where the bootloader
has provided invalid information. However, on some machines the overrides
may do more harm than good due to configuration differences between machines
with the same machine identifier. It turns out that it's possible for the
bootloader to get the correct information on GOP-based systems, but we
can't guarantee that the kernel's being booted with one that's been updated
to do so. Add support for a capabilities flag that can be set by the
bootloader, and skip the DMI checks in that case. Additionally, set this
flag in the UEFI stub code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
We can't assume the presence of the red zone while we're still in a boot
services environment, so we should build with -fno-red-zone to avoid
problems. Change the size of wchar at the same time to make string handling
simpler.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
We currently use the PCI IO protocol as a proxy for a functional GOP. This
is less than ideal, since some platforms will put the GOP on output devices
rather than the GPU itself. Move to using the conout protocol. This is not
guaranteed per-spec, but is part of the consplitter implementation that
causes this problem in the first place and so should be reliable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The named constant RAMDISK is unused. It used to set the (obsolete)
kernel boot header field ram_size, but its usage for that purpose got
dropped in commit 5e47c478b0 ("x86: remove
zImage support"). Now remove this constant too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Link: http://lkml.kernel.org/r/1345396003.1771.9.camel@x61.thuisdomein
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
GCC built with nonstandard options can enable -fpic by default.
We never want this for 32-bit kernels and it will break the build.
[ hpa: Notably the Android toolchain apparently does this. ]
Change-Id: Iaab7d66e598b1c65ac4a4f0229eca2cd3d0d2898
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Link: http://lkml.kernel.org/r/1344624546-29691-1-git-send-email-andrew.p.boie@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pul x86/efi changes from Ingo Molnar:
"This tree adds an EFI bootloader handover protocol, which, once
supported on the bootloader side, will make bootup faster and might
result in simpler bootloaders.
The other change activates the EFI wall clock time accessors on x86-64
as well, instead of the legacy RTC readout."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Handover Protocol
x86-64/efi: Use EFI to deal with platform wall clock
Pull x86 cleanup and cpufeature from Ingo Molnar:
"Just a single cleanup and and a commit that adds new CPU feature
names"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Remove ancient, unconditionally #ifdef'd out dead code
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Add the RDSEED and ADX features
CONFIG_EARLY_PRINTK is the only feature that might use command line
parsing in the decompression stage. If it is disabled then we can
exclude the related code to save space. This can result in an estimated
space savings of 2240 bytes from the compressed kernel image.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-8-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Removes early_serial_console.c code if we don't have the config option that
enables it (EARLY_PRINTK). When disabling this code, make early_serial_base a
constant 0 to allow the compiler to optimize away the code that checks for
early_serial_base.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-7-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
As we're no longer using the flag we don't need to extract the value from the
command line and store it. This is a step towards removing command line
parameter code.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-6-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Changed putstr flagging from parameter to conditional compilation for puts,
debug_putstr, and error_putstr. This allows for space savings since most
configurations won't use this feature.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-5-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For consistency we changed the error output path to match the new debug path.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-4-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Change all instances of if (debug) putstr(...) to a new debug_putstr(...).
This allows a future change to conditionally stub out debug_putstr to save
space.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-3-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There are only 3 uses of the quiet flag and they all protect output that
is only useful for debugging the stub, therefore we switched to using the
debug flag for all extra output.
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Link: http://lkml.kernel.org/r/1342746282-28497-2-git-send-email-jmillenbach@gmail.com
Signed-off-by: Gokul Caushik <caushik1@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
As things currently stand, traditional EFI boot loaders and the EFI
boot stub are carrying essentially the same initialisation code
required to setup an EFI machine for booting a kernel. There's really
no need to have this code in two places and the hope is that, with
this new protocol, initialisation and booting of the kernel can be
left solely to the kernel's EFI boot stub. The responsibilities of the
boot loader then become,
o Loading the kernel image from boot media
File system code still needs to be carried by boot loaders for the
scenario where the kernel and initrd files reside on a file system
that the EFI firmware doesn't natively understand, such as ext4, etc.
o Providing a user interface
Boot loaders still need to display any menus/interfaces, for example
to allow the user to select from a list of kernels.
Bump the boot protocol number because we added the 'handover_offset'
field to indicate the location of the handover protocol entry point.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-and-Tested-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1342689828-16815-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Release v1.3.82 wrapped a few lines of code in an "#ifdef
SAFE_RESET_DISK_CONTROLLER" and "#endif" pair. Since
SAFE_RESET_DISK_CONTROLLER was never defined anywhere that was basically
a verbose "#ifdef 0" and "#endif" pair. These dead lines have been in
the tree for sixteen years but now the time has come to remove them.
I guess the main lesson here is that if you want your dead code in the
tree for a very long time you'd better be creative. A plain old "#ifdef
0" and "#endif" pair just doesn't cut it!
See: http://lkml.kernel.org/r/199603301718.LAA00178@craie.inetnebr.com
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Link: http://lkml.kernel.org/r/1340230589.1773.7.camel@x61.thuisdomein
Acked-by: Jeff Epler <jepler@unpythonic.net>
Acked-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.
Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)
To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.com
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We need a way of printing useful messages to the user, for example
when we fail to open an initrd file, instead of just hanging the
machine without giving the user any indication of what went wrong. So
sprinkle some error messages throughout the EFI boot stub code to make
it easier for users to diagnose/report problems.
Reported-by: Keshav P R <the.ridikulus.rat@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-3-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The loop at the 'close_handles' label in handle_ramdisks() should be
using 'i', which represents the number of initrd files that were
successfully opened, not 'nr_initrds' which is the number of initrd=
arguments passed on the command line.
Currently, if we execute the loop to close all file handles and we
failed to open any initrds we'll try to call the close function on a
garbage pointer, causing the machine to hang.
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-2-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull x86 platform changes from Ingo Molnar:
"This tree includes assorted platform driver updates and a preparatory
series for a platform with custom DMA remapping semantics (sta2x11 I/O
hub)."
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vsmp: Fix number of CPUs when vsmp is disabled
keyboard: Use BIOS Keyboard variable to set Numlock
x86/olpc/xo1/sci: Report RTC wakeup events
x86/olpc/xo1/sci: Produce wakeup events for buttons and switches
x86, platform: Initial support for sta2x11 I/O hub
x86: Introduce CONFIG_X86_DMA_REMAP
x86-32: Introduce CONFIG_X86_DEV_DMA_OPS
Pull x86 EFI updates from Ingo Molnar:
"This patchset makes changes to the bzImage EFI header, so that it can
be signed with a secure boot signature tool. It should not affect
anyone who is not using the EFI self-boot feature in any way."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Fix NumberOfRvaAndSizes field in PE32 header for EFI_STUB
x86, efi: Fix .text section overlapping image header for EFI_STUB
x86, efi: Fix issue of overlapping .reloc section for EFI_STUB
A new option is added to the relocs tool called '--realmode'.
This option causes the generation of 16-bit segment relocations
and 32-bit linear relocations for the real-mode code. When
the real-mode code is moved to the low-memory during kernel
initialization, these relocation entries can be used to
relocate the code properly.
In the assembly code 16-bit segment relocations must be relative
to the 'real_mode_seg' absolute symbol. Linear relocations must be
relative to a symbol prefixed with 'pa_'.
16-bit segment relocation is used to load cs:ip in 16-bit code.
Linear relocations are used in the 32-bit code for relocatable
data references. They are declared in the linker script of the
real-mode code.
The relocs tool is moved to arch/x86/tools/relocs.c, and added new
target archscripts that can be used to build scripts needed building
an architecture. be compiled before building the arch/x86 tree.
[ hpa: accelerating this because it detects invalid absolute
relocations, a serious bug in binutils 2.22.52.0.x which currently
produces bad kernels. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-2-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
The PC BIOS does provide a NUMLOCK flag containing the desired state
of this LED. This patch sets the current state according to the data
in the bios.
[ hpa: fixed __weak declaration without definition, changed "inline"
to "static inline" ]
Signed-Off-By: Joshua Cov <joshuacov@googlemail.com>
Link: http://lkml.kernel.org/r/CAKL7Q7rvq87TNS1T_Km8fW_5OzS%2BSbYazLXKxW-6ztOxo3zorg@mail.gmail.com
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
sh_symtab is set but not used.
[ hpa: putting this in urgent because of the sheer harmlessness of the patch:
it quiets a build warning but does not change any generated code. ]
Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Link: http://lkml.kernel.org/r/20120401082932.D5E066FC03D@msa105.auone-net.jp
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
The method used to work out whether we were booted by EFI firmware or
via a boot loader is broken. Because efi_main() is always executed
when booting from a boot loader we will dereference invalid pointers
either on the stack (CONFIG_X86_32) or contained in %rdx
(CONFIG_X86_64) when searching for an EFI System Table signature.
Instead of dereferencing these invalid system table pointers, add a
new entry point that is only used when booting from EFI firmware, when
we know the pointer arguments will be valid. With this change legacy
boot loaders will no longer execute efi_main(), but will instead skip
EFI stub initialisation completely.
[ hpa: Marking this for urgent/stable since it is a regression when
the option is enabled; without the option the patch has no effect ]
Signed-off-by: Matt Fleming <matt.hfleming@intel.com>
Link: http://lkml.kernel.org/r/1334584744.26997.14.camel@mfleming-mobl1.ger.corp.intel.com
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> v3.3
Reason for merge:
The updates to the EFI boot stub generation conflicted with the
changes to properly use the get/put_unaligned_le*() macros to
generate images.
This merge commit completes the conversion in
arch/x86/boot/tools/build.c including the places in the code
which had been changed on the x86/efi branch.
Resolved Conflicts:
arch/x86/boot/tools/build.c
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We've actually got six data directories in the header, not one. Even
though the firmware loader doesn't seem to mind, when we come to sign
the kernel image the signing tool thinks that there is no Certificate
Table data directory, even though we've allocated space for one.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-4-git-send-email-jordan.l.justen@intel.com
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This change modifes the PE .text section to start after
the first sector of the kernel image.
The header may be modified by the UEFI secure boot signing,
so it is not appropriate for it to be included in one of the
image sections. Since the sections are part of the secure
boot hash, this modification to the .text section contents
would invalidate the secure boot signed hash.
Note: UEFI secure boot does hash the image header, but
fields that are changed by the signing process are excluded
from the hash calculation. This exclusion process is only
handled for the image header, and not image sections.
Luckily, we can still easily boot without the first sector
by initializing a few fields in arch/x86/boot/compressed/eboot.c.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-3-git-send-email-jordan.l.justen@intel.com
[jordan.l.justen@intel.com: set .text vma & file offset]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Previously the .reloc section was embedded in the .text
section.
No relocations are required during the PE/COFF loading phase
for the kernel using the EFI_STUB UEFI loader. To fix the
issue of overlapping sections, create a .reloc section with a
zero length.
The .reloc section header must exist to make sure the image
will be loaded by the UEFI firmware, but a zero-length
section header seems to be sufficient.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-2-git-send-email-jordan.l.justen@intel.com
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is a partial revert of commit:
d40f833 "Restrict CFLAGS for hostprogs"
The endian-manipulation macros in tools/include need <linux/types.h>,
but the hostprogs in arch/x86/boot need several headers from the
kernel build tree, which means we have to add the kernel headers to
the include path. This picks up <linux/types.h> from the kernel tree,
which gives a warning.
Since this use of <linux/types.h> is intentional, add
-D__EXPORTED_HEADERS__ to the command line to silence the warning.
A better way to fix this would be to always install the exported
kernel headers into $(objtree)/usr/include as a standard part of the
kernel build, but that is a lot more involved.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1330436245-24875-5-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull x86 "urgent" leftovers from Ingo Molnar:
"Pending x86/urgent bits that were not high prio enough to warrant
-rc-less v3.3-final inclusion."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Fix pointer math issue in handle_ramdisks()
x86/ioapic: Add register level checks to detect bogus io-apic entries
x86, mce: Fix rcu splat in drain_mce_log_buffer()
x86, memblock: Move mem_hole_size() to .init
Pull trivial x86 branches from Ingo Molnar: small one-liners to fix up
details.
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove some noise from boot log when starting cpus
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Fix port argument to inl() function
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Add CPU features from Intel document 319433-012A
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64: Record stack pointer before task execution begins
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/UV: Lower UV rtc clocksource rating
"filename" is a efi_char16_t string so this check for reaching the end
of the array doesn't work. We need to cast the pointer to (u8 *) before
doing the math.
This patch changes the "filename" to "filename_16" to avoid confusion in
the future.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://lkml.kernel.org/r/20120305180614.GA26880@elgon.mountain
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It would appear that we never actually generated a correct CRC when
building on a bigendian machine. Depending on the word size, we would
either generate an all-zero CRC (64-bit machine) or a byte-swapped
CRC (32-bit machine.) Fix the types used so we don't arbitrarily use
a 64-bit word to hold 32-bit numbers, and pass the CRC through
put_unaligned_le32() like all the other numbers.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Link: http://lkml.kernel.org/r/20120229111322.9eb4b23ff1672e8853ad3b3b@canb.auug.org.au
We include <sys/sysmacros.h> and <asm/boot.h>, but none of those
header files actually provide anything this file needs. Furthermore,
it breaks cross-compilation, so just remove them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Link: http://lkml.kernel.org/r/20120229111322.9eb4b23ff1672e8853ad3b3b@canb.auug.org.au
We may need to convert the endianness of the data we read from/write
to 'buf', so let's use {get,put}_unaligned_le32() to do that. Failure
to do so can result in accessing invalid memory, leading to a
segfault. Stephen Rothwell noticed this bug while cross-building an
x86_64 allmodconfig kernel on PowerPC.
We need to read from and write to 'buf' a byte at a time otherwise
it's possible we'll perform an unaligned access, which can lead to bus
errors when cross-building an x86 kernel on risc architectures.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1330436245-24875-6-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently tools/build has access to all the kernel headers in
$(srctree). This is unnecessary and could potentially allow
tools/build to erroneously include kernel headers when it should only
be including userspace-exported headers.
Unfortunately, mkcpustr still needs access to some of the asm kernel
headers, so explicitly special case that hostprog.
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1330436245-24875-5-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"u32 port" in inl() should be "u16 port".
[ hpa: it's a bug, but it doesn't produce incorrect code, so no need
to put this into urgent or stable. ]
Signed-off-by: He Chunhui <hchunhui@mail.ustc.edu.cn>
Link: http://lkml.kernel.org/r/32892299.2931391328028508117.JavaMail.coremail@mailweb
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The efi boot stub tries to read the entire initrd in 1 go, however
some efi implementations hang if too much if asked to read too much
data at the same time. After some experimentation I found out that my
asrock p67 board will hang if asked to read chunks of 4MiB, so use a
safe value.
elilo reads in chunks of 16KiB, but since that requires many read
calls I use a value of 1 MiB. hpa suggested adding individual
blacklists for when systems are found where this value causes a crash.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4EEB3A02.3090201@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There is currently a large divide between kernel development and the
development of EFI boot loaders. The idea behind this patch is to give
the kernel developers full control over the EFI boot process. As
H. Peter Anvin put it,
"The 'kernel carries its own stub' approach been very successful in
dealing with BIOS, and would make a lot of sense to me for EFI as
well."
This patch introduces an EFI boot stub that allows an x86 bzImage to
be loaded and executed by EFI firmware. The bzImage appears to the
firmware as an EFI application. Luckily there are enough free bits
within the bzImage header so that it can masquerade as an EFI
application, thereby coercing the EFI firmware into loading it and
jumping to its entry point. The beauty of this masquerading approach
is that both BIOS and EFI boot loaders can still load and run the same
bzImage, thereby allowing a single kernel image to work in any boot
environment.
The EFI boot stub supports multiple initrds, but they must exist on
the same partition as the bzImage. Command-line arguments for the
kernel can be appended after the bzImage name when run from the EFI
shell, e.g.
Shell> bzImage console=ttyS0 root=/dev/sdb initrd=initrd.img
v7:
- Fix checkpatch warnings.
v6:
- Try to allocate initrd memory just below hdr->inird_addr_max.
v5:
- load_options_size is UTF-16, which needs dividing by 2 to convert
to the corresponding ASCII size.
v4:
- Don't read more than image->load_options_size
v3:
- Fix following warnings when compiling CONFIG_EFI_STUB=n
arch/x86/boot/tools/build.c: In function ‘main’:
arch/x86/boot/tools/build.c:138:24: warning: unused variable ‘pe_header’
arch/x86/boot/tools/build.c:138:15: warning: unused variable ‘file_sz’
- As reported by Matthew Garrett, some Apple machines have GOPs that
don't have hardware attached. We need to weed these out by
searching for ones that handle the PCIIO protocol.
- Don't allocate memory if no initrds are on cmdline
- Don't trust image->load_options_size
Maarten Lankhorst noted:
- Don't strip first argument when booted from efibootmgr
- Don't allocate too much memory for cmdline
- Don't update cmdline_size, the kernel considers it read-only
- Don't accept '\n' for initrd names
v2:
- File alignment was too large, was 8192 should be 512. Reported by
Maarten Lankhorst on LKML.
- Added UGA support for graphics
- Use VIDEO_TYPE_EFI instead of hard-coded number.
- Move linelength assignment until after we've assigned depth
- Dynamically fill out AddressOfEntryPoint in tools/build.c
- Don't use magic number for GDT/TSS stuff. Requested by Andi Kleen
- The bzImage may need to be relocated as it may have been loaded at
a high address address by the firmware. This was required to get my
macbook booting because the firmware loaded it at 0x7cxxxxxx, which
triggers this error in decompress_kernel(),
if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
error("Destination address too large");
Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <mjg@redhat.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1321383097.2657.9.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This has been obsoleted by the root= commandline and the rdev utility
for many, many years. People who still depend on this will surely
have a copy of the rdev utility around, the rest of the world gets rid
of another piece of buildhost-dependent data in the build. Thanks to
Paul Bolle for the build.c cleanup.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Link: http://lkml.kernel.org/r/1302607824-24699-1-git-send-email-mmarek@suse.cz
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When we use BIOS function e801 to probe memory, we should use ax/bx
(or cx/dx) as a pair, not mix and match. This was a typo during the
translation from assembly code, and breaks at least one set of
machines in the field (which return cx = dx = 0).
Reported-and-tested-by: Chris Samuel <chris@csamuel.org>
Fix-proposed-by: Thomas Meyer <thomas@m3y3r.de>
Link: http://lkml.kernel.org/r/1303566747.12067.10.camel@localhost.localdomain
Ensure build doesn't silently continue despite read failure,
addressing a warning due to the unchecked call.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
LKML-Reference: <AANLkTimxxTMU3=4ry-_zbY6v1xiDi+hW9y1RegTr8vLK@mail.gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This integrates the XZ decompression code to the x86 pre-boot code.
mkpiggy.c is updated to reserve about 32 KiB more buffer safety margin for
kernel decompression. It is done unconditionally for all decompressors to
keep the code simpler.
The XZ decompressor needs around 30 KiB of heap, so the heap size is
increased to 32 KiB on both x86-32 and x86-64.
Documentation/x86/boot.txt is updated to list the XZ magic number.
With the x86 BCJ filter in XZ, XZ-compressed x86 kernel tends to be a few
percent smaller than the equivalent LZMA-compressed kernel.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alain Knaff <alain@knaff.lu>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix included-by file reference comments
x86, cpu: Only CPU features determine NX capabilities
x86, cpu: Call verify_cpu during 32bit CPU startup
x86, cpu: Clear XD_DISABLED flag on Intel to regain NX
x86, cpu: Rename verify_cpu_64.S to verify_cpu.S
A relocatable kernel can be anywhere in lowmem -- and in the case of a
kdump kernel, is likely to be fairly high. Since the early page
tables map everything from address zero up we need to make sure we
allocate enough brk that we can map all of lowmem if we need to.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD3ED.8070607@kernel.org>
The code is 32bit already, and can be used in 32bit routines.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
LKML-Reference: <1289414154-7829-2-git-send-email-kees.cook@canonical.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The kernel decompression code parses the ELF header and then copies
the segment to the corresponding destination. Currently it uses slow
byte-copy code. This patch makes it use the string copy operations
instead.
In the test the copy performance can be improved very significantly after using
the string copy operation mechanism.
1. The copy time can be reduced from 150ms to 20ms on one Atom machine
2. The copy time can be reduced about 80% on another machine
The time is reduced from 7ms to 1.5ms when using 32-bit kernel.
The time is reduced from 10ms to 2ms when using 64-bit kernel.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
LKML-Reference: <1286502453-7043-1-git-send-email-yakui.zhao@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
earlyprintk can take and I/O port, so we need to handle this case in
the setup code too, otherwise 0x3f8 will be treated as a baud rate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B05A6.4010801@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Torsten reported that there is garbage output,
after commit 8fee13a48e (x86,
setup: enable early console output from the decompressor)
It turns out we missed the offset for that case.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B0578.8090807@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It is a subset of <ctype.h> functionality, so name it ctype.h. Also,
reorganize header files so #include statements are clustered near the
top as they should be.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4C5752F2.8030206@kernel.org>
This enables the decompressor output to be seen on the serial console.
Most of the code is shared with the regular boot code.
We could add printf to the decompressor if needed, but currently there
is no sufficiently compelling user.
-v2: define BOOT_BOOT_H to avoid include boot.h
-v3: early_serial_base need to be static in misc.c ?
-v4: create seperate string.c printf.c cmdline.c early_serial_console.c
after hpa's patch that allow global variables in compressed/misc stage
-v5: remove printf.c related
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Separate early_serial_console from tty.c
This allows for reuse of
early_serial_console.c/string.c/printf.c/cmdline.c in boot/compressed/.
-v2: according to hpa, don't include string.c etc
-v3: compressed/misc.c must have early_serial_base as static, so move it back to tty.c
for setup code
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C568D2B.205@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In order for global variables and functions to work in the
decompressor, we need to fix up the GOT in assembly code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4C57382E.8050501@zytor.com>
putchar is using early_serial_base to check if port is initialized.
So we only assign it after early_serial_init() is called,
in case we need use VGA to debug early serial console.
Also add display for port addr and baud.
-v2: update to current tip
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3E0171.6050008@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Make the boot code also accept the console=uart8250,io,0x2f8,115200n
form of early console.
Also add back simple_guess_base(), otherwise those simple_strtoull(,,0)
are not going to work.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3CCE05.4090505@kernel.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds serial I/O support to the real-mode setup (very early
boot) printf(). It's useful for debugging boot code when running Linux
under KVM, for example. The actual code was lifted from early printk.
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1278835617-11368-1-git-send-email-penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Catch missing conversion to the register structure "glove box" scheme.
Found by gcc 4.6's new warnings.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100610111040.F1781B1A2B@basil.firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-35' of git://repo.or.cz/linux-kbuild: (81 commits)
kbuild: Revert part of e8d400a to resolve a conflict
kbuild: Fix checking of scm-identifier variable
gconfig: add support to show hidden options that have prompts
menuconfig: add support to show hidden options which have prompts
gconfig: remove show_debug option
gconfig: remove dbg_print_ptype() and dbg_print_stype()
kconfig: fix zconfdump()
kconfig: some small fixes
add random binaries to .gitignore
kbuild: Include gen_initramfs_list.sh and the file list in the .d file
kconfig: recalc symbol value before showing search results
.gitignore: ignore *.lzo files
headerdep: perlcritic warning
scripts/Makefile.lib: Align the output of LZO
kbuild: Generate modules.builtin in make modules_install
Revert "kbuild: specify absolute paths for cscope"
kbuild: Do not unnecessarily regenerate modules.builtin
headers_install: use local file handles
headers_check: fix perl warnings
export_report: fix perl warnings
...
This reverts commit b3b77c8cae, which was
also totally broken (see commit 0d2daf5cc8 that reverted the crc32
version of it). As reported by Stephen Rothwell, it causes problems on
big-endian machines:
> In file included from fs/jfs/jfs_types.h:33,
> from fs/jfs/jfs_incore.h:26,
> from fs/jfs/file.c:22:
> fs/jfs/endian24.h:36:101: warning: "__LITTLE_ENDIAN" is not defined
The kernel has never had that crazy "__BYTE_ORDER == __LITTLE_ENDIAN"
model. It's not how we do things, and it isn't how we _should_ do
things. So don't go there.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux does not define __BYTE_ORDER in its endian header files which makes
some header files bend backwards to get at the current endian. Lets
#define __BYTE_ORDER in big_endian.h/litte_endian.h to make it easier for
header files that are used in user space too.
In userspace the convention is that
1. _both_ __LITTLE_ENDIAN and __BIG_ENDIAN are defined,
2. you have to test for e.g. __BYTE_ORDER == __BIG_ENDIAN.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: Don't skip mode setting for the standard VGA modes
x86-64, setup: Inhibit decompressor output if video info is invalid
x86, setup: When restoring the screen, update boot_params.screen_info
The code for setting standard VGA modes probes for the current mode,
and skips the mode setting if the mode is 3 (color text 80x25) or 7
(mono text 80x25). Unfortunately, there are BIOSes, including the
VMware BIOS, which report the previous mode if function 0F is queried
while the screen is in a VESA mode, and of course, nothing can help a
mode poked directly into the hardware.
As such, the safe option is to set the mode anyway, and only query to
see if we should be using mode 7 rather than mode 3. People who don't
want any mode setting at all should probably use vga=0x0f04
(VIDEO_CURRENT_MODE). It's possible that should be the kernel
default.
Reported-by Rene Arends <R.R.Arends@hro.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
Inhibit output from the kernel decompressor if the video information
is invalid. This was already the case for 32 bits, make 64 bits
match.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
When we restore the screen content after a mode change, we return the
cursor to its former position. However, we need to also update
boot_params.screen_info accordingly, so that the decompression code
knows where on the screen the cursor is. Just in case the video BIOS
does something extra screwy, read the cursor position back from the
BIOS instead of relying on it doing the right thing.
While we're at it, make sure we cap the cursor position to the new
screen coordinates.
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Bugzilla-Reference: http://bugzilla.kernel.org/show_bug.cgi?id=15329
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: x86@kernel.org
LKML-Reference: <1265478443-31072-10-git-send-email-elendil@planet.nl>
[ Left out the KVM bits. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Iomem has no special significance on x86. Use the standard mem*
functions instead of trying to call other versions. Some fixups
are needed to match the function prototypes.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-6-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, some distros have started shipping versions of gcc which
default to -march=i686. This breaks building kernels for pre-i686
machines, even if they have been selected in Kconfig, due to the
generation of CMOV instructions.
There isn't enough benefit to try to preserve the generation of these
instructions even when selected, so simply force -march=i386 for the
decompressor when building a 32-bit kernel.
Reported-and-tested-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <219280.97558.qm@web52907.mail.re2.yahoo.com>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
This adds a new category of symbols to the relocs program: symbols
which are known to be relative, even though the linker emits them as
absolute; this is the case for symbols that live in the linker script,
which currently applies to _end.
Unfortunately the previous workaround of putting _end in its own empty
section was defeated by newer binutils, which remove empty sections
completely.
This patch also changes the symbol matching to use regular expressions
instead of hardcoded C for specific patterns.
This is a decidedly non-minimal patch: a modified version of the
relocs program is used as part of the Syslinux build, and this is
basically a backport to Linux of some of those changes; they have
thus been well tested.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4AF86211.3070103@zytor.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
vgacon: Add support for setting the default cursor state
vc: Add support for hiding the cursor when creating VTs
x86, setup: Store the boot cursor state
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86, mm: Correct the implementation of is_untracked_pat_range()
x86/pat: Trivial: don't create debugfs for memtype if pat is disabled
x86, mtrr: Fix sorting of mtrr after subtracting
x86: Move find_smp_config() earlier and avoid bootmem usage
x86, platform: Change is_untracked_pat_range() to bool; cleanup init
x86: Change is_ISA_range() into an inline function
x86, mm: is_untracked_pat_range() takes a normal semiclosed range
x86, mm: Call is_untracked_pat_range() rather than is_ISA_range()
x86: UV SGI: Don't track GRU space in PAT
x86: SGI UV: Fix BAU initialization
x86, numa: Use near(er) online node instead of roundrobin for NUMA
x86, numa, bootmem: Only free bootmem on NUMA failure path
x86: Change crash kernel to reserve via reserve_early()
x86: Eliminate redundant/contradicting cache line size config options
x86: When cleaning MTRRs, do not fold WP into UC
x86: remove "extern" from function prototypes in <asm/proto.h>
x86, mm: Report state of NX protections during boot
x86, mm: Clean up and simplify NX enablement
x86, pageattr: Make set_memory_(x|nx) aware of NX support
x86, sleep: Always save the value of EFER
...
Fix up conflicts (added both iommu_shutdown and is_untracked_pat_range)
to 'struct x86_platform_ops') in
arch/x86/include/asm/x86_init.h
arch/x86/kernel/x86_init.c
Rather than having X86_L1_CACHE_BYTES and X86_L1_CACHE_SHIFT
(with inconsistent defaults), just having the latter suffices as
the former can be easily calculated from it.
To be consistent, also change X86_INTERNODE_CACHE_BYTES to
X86_INTERNODE_CACHE_SHIFT, and set it to 7 (128 bytes) for NUMA
to account for last level cache line size (which here matters
more than L1 cache line size).
Finally, make sure the default value for X86_L1_CACHE_SHIFT,
when X86_GENERIC is selected, is being seen before that for the
individual CPU model options (other than on x86-64, where
GENERIC_CPU is part of the choice construct, X86_GENERIC is a
separate option on ix86).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Ravikiran Thirumalai <kiran@scalex86.org>
Acked-by: Nick Piggin <npiggin@suse.de>
LKML-Reference: <4AFD5710020000780001F8F0@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a field to store the boot cursor state and implement this for VGA on
x86. This can then be used to set the default policy for the boot console.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
LKML-Reference: <1258142222-16092-1-git-send-email-mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A single 'movl' is shorter than the 'xorl'-'orl' pair.
No change in behaviour.
Signed-off-by: Alexander Potashev <aspotashev@gmail.com>
LKML-Reference: <1256341043-4928-1-git-send-email-aspotashev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Older binutils breaks if ASSERT() is used without a sink
for the output.
For example 2.14.90.0.6 is known to be broken, the link
fails with:
LD .tmp_vmlinux1
ld:arch/x86/kernel/vmlinux.lds:678: parse error
Document this quirk in all three files that use it.
See: http://marc.info/?l=linux-kbuild&m=124930110427870&w=2
See[2]: d2ba8b2 ("x86: Fix assert syntax in vmlinux.lds.S")
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Remove redundant non-NUMA topology functions
x86: early_printk: Protect against using the same device twice
x86: Reduce verbosity of "PAT enabled" kernel message
x86: Reduce verbosity of "TSC is reliable" message
x86: mce: Use safer ways to access MCE registers
x86: mce, inject: Use real inject-msg in raise_local
x86: mce: Fix thermal throttling message storm
x86: mce: Clean up thermal throttling state tracking code
x86: split NX setup into separate file to limit unstack-protected code
xen: check EFER for NX before setting up GDT mapping
x86: Cleanup linker script using new linker script macros.
x86: Use section .data.page_aligned for the idt_table.
x86: convert to use __HEAD and HEAD_TEXT macros.
x86: convert compressed loader to use __HEAD and HEAD_TEXT macros.
x86: fix fragile computation of vsyscall address
Replace the use of CROSS_COMPILE to select a customized
installkernel script with the possibility to set INSTALLKERNEL
to select a custom installkernel script when running make:
make INSTALLKERNEL=arm-installkernel install
With this patch we are now more consistent across
different architectures - they did not all support use
of CROSS_COMPILE.
The use of CROSS_COMPILE was a hack as this really belongs
to gcc/binutils and the installkernel script does not change
just because we change toolchain.
The use of CROSS_COMPILE caused troubles with an upcoming patch
that saves CROSS_COMPILE when a kernel is built - it would no
longer be installable.
[Thanks to Peter Z. for this hint]
This patch undos what Ian did in commit:
0f8e2d62fa
("use ${CROSS_COMPILE}installkernel in arch/*/boot/install.sh")
The patch has been lightly tested on x86 only - but all changes
looks obvious.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mike Frysinger <vapier@gentoo.org> [blackfin]
Acked-by: Russell King <linux@arm.linux.org.uk> [arm]
Acked-by: Paul Mundt <lethal@linux-sh.org> [sh]
Acked-by: "H. Peter Anvin" <hpa@zytor.com> [x86]
Cc: Ian Campbell <icampbell@arcom.com>
Cc: Tony Luck <tony.luck@intel.com> [ia64]
Cc: Fenghua Yu <fenghua.yu@intel.com> [ia64]
Cc: Hirokazu Takata <takata@linux-m32r.org> [m32r]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Kyle McMartin <kyle@mcmartin.ca> [parisc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> [powerpc]
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Cc: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Ingo Molnar <mingo@redhat.com> [x86]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text".
Linus suggested that we merge the ".text.head" section with ".text"
(presumably while preserving the fact that the head code starts at 0).
When I tried this it caused the kernel to not boot.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being
included, which in turn leads to it and all its dependents always
getting rebuilt independent of whether they are already up-to-date.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Some intcall() misuses the input biosregs as output in
cf06de7b9c
This fixes the problem vga=ask boot option doesn't show enough modes.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
LKML-Reference: <20090701021307.GA3127@localhost.localdomain>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There were a set of pre-Kconfig configuration variables defined in the
video code. There is absolutely no evidence that they have been
tweaked by anybody in modern history, so just get rid of them and hope
nobody notices. If someone does complain, these should be made real
Kconfig variables.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (45 commits)
x86, mce: fix error path in mce_create_device()
x86: use zalloc_cpumask_var for mce_dev_initialized
x86: fix duplicated sysfs attribute
x86: de-assembler-ize asm/desc.h
i386: fix/simplify espfix stack switching, move it into assembly
i386: fix return to 16-bit stack from NMI handler
x86, ioapic: Don't call disconnect_bsp_APIC if no APIC present
x86: Remove duplicated #include's
x86: msr.h linux/types.h is only required for __KERNEL__
x86: nmi: Add Intel processor 0x6f4 to NMI perfctr1 workaround
x86, mce: mce_intel.c needs <asm/apic.h>
x86: apic/io_apic.c: dmar_msi_type should be static
x86, io_apic.c: Work around compiler warning
x86: mce: Don't touch THERMAL_APIC_VECTOR if no active APIC present
x86: mce: Handle banks == 0 case in K7 quirk
x86, boot: use .code16gcc instead of .code16
x86: correct the conversion of EFI memory types
x86: cap iomem_resource to addressable physical memory
x86, mce: rename _64.c files which are no longer 64-bit-specific
x86, mce: mce.h cleanup
...
Manually fix up trivial conflict in arch/x86/mm/fault.c
Enable gcov profiling of the entire kernel on x86_64. Required changes
include disabling profiling for:
* arch/kernel/acpi/realmode and arch/kernel/boot/compressed:
not linked to main kernel
* arch/vdso, arch/kernel/vsyscall_64 and arch/kernel/hpet:
profiling causes segfaults during boot (incompatible context)
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use .code16gcc to compile arch/x86/boot/bioscall.S rather than
.code16, since some older versions of binutils can't generate 32-bit
addressing expressions (67 prefixes) in .code16 mode, only in
.code16gcc mode.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
git status complains of untracked (generated) files in arch/x86/boot..
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# ../../arch/x86/boot/compressed/mkpiggy
# ../../arch/x86/boot/compressed/piggy.S
# ../../arch/x86/boot/compressed/vmlinux.lds
# ../../arch/x86/boot/voffset.h
# ../../arch/x86/boot/zoffset.h
..so adjust .gitignore files accordingly.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For relocatable 32bit kernels, boot/compressed/relocs.c processes
relocation entries in the kernel image and appends it to the kernel
image such that boot/compressed/head_32.S can relocate the kernel.
The kernel image is one statically linked object and only uses two
relocation types - R_386_PC32 and R_386_32, of the two only the latter
needs massaging during kernel relocation and thus handled by relocs.
R_386_PC32 is ignored and all other relocation types are considered
error.
When the target of a relocation resides in a discarded section,
binutils doesn't throw away the relocation record but nullifies it by
changing it to R_386_NONE, which unfortunately makes relocs fail.
The problem was triggered by yet out-of-tree x86 stack unwind patches
but given the binutils behavior, ignoring R_386_NONE is the right
thing to do.
The problem has been tracked down to binutils behavior by Jan Beulich.
[ Impact: fix build with certain binutils by ignoring R_386_NONE ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <4A1B8150.40702@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove ACPI 3 E820 extended memory attributes support. At least one
vendor actively set all the flags to zero, but left ECX on return at
24. This bug may be present in other BIOSes.
The breakage functionally means the ACPI 3 flags are probably
completely useless, and that no OS any time soon is going to rely on
their existence. Therefore, drop support completely. We may want to
revisit this question in the future, if we find ourselves actually
needing the flags.
This reverts all or part of the following checkins:
cd670599b7c549e71d07
However, retain the part from the latter commit that copies e820 into
a temporary buffer; that is an unrelated BIOS workaround. Put in a
comment to explain that part.
See https://bugzilla.redhat.com/show_bug.cgi?id=499396 for some
additional information.
[ Impact: detect all memory on affected machines ]
Reported-by: Thomas J. Baker <tjb@unh.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Len Brown <len.brown@intel.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Kyle McMartin <kmcmartin@redhat.com>
Cc: Matt Domsch <matt_domsch@dell.com>
Correct the calculation of ZO_INIT_SIZE (the amount of memory we need
during decompression). One symbol (ZO_startup_32) was missing from
zoffset.h, and another (ZO_z_extract_offset) was misspelled.
[ Impact: build fix ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
arch/x86/boot/compressed/misc.c contains several sanity checks on the
output address. Correct constraints that are no longer correct:
- the alignment test should be MIN_KERNEL_ALIGN on both 32 and 64
bits.
- the 64 bit maximum address was set to 2^40, which was the limit of
one specific x86-64 implementation. Change the test to 2^46, the
current Linux limit, and at least try to test the end rather than
the beginning.
- for non-relocatable kernels, test against LOAD_PHYSICAL_ADDR on both
32 and 64 bits.
[ Impact: fix potential boot failure due to invalid tests ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make the kernel_alignment field adjustable; this allows us to set it
to a large value (intended to be 16 MB to avoid ZONE_DMA contention,
memory holes and other weirdness) while a smart bootloader can still
force a loading at a lesser alignment if absolutely necessary.
Also export pref_address (preferred loading address, corresponding to
the link-time address) and init_size, the total amount of linear
memory the kernel will require during initialization.
[ Impact: allows better kernel placement, gives bootloader more info ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove a couple of lines of dead code from
arch/x86/boot/compressed/head_*.S; all of these update registers that
are dead in the current code.
[ Impact: cleanup ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Use LOAD_PHYSICAL_ADDR instead of CONFIG_PHYSICAL_START in the 64-bit
decompression code, for equivalence with the 32-bit code.
[ Impact: cleanup, increases code similarity ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make symbols from the main vmlinux, as opposed to just
compressed/vmlinux, available to header.S. Also, export a few
additional symbols.
This will be used in a subsequent patch to export the total memory
footprint of the kernel.
[ Impact: enable future enhancement ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Determine the compressed code offset (from the kernel runtime address)
at compile time. This allows some minor optimizations in
arch/x86/boot/compressed/head_*.S, but more importantly it makes this
value available to the build process, which will enable a future patch
to export the necessary linear memory footprint into the bzImage
header.
[ Impact: cleanup, future patch enabling ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In the pre-decompression code, use the appropriate largest possible
rep movs and rep stos to move code and clear bss, respectively. For
reverse copy, do note that the initial values are supposed to be the
address of the first (highest) copy datum, not one byte beyond the end
of the buffer.
rep strings are not necessarily the fastest way to perform these
operations on all current processors, but are likely to be in the
future, and perhaps more importantly, we want to encourage the
architecturally right thing to do here.
This also fixes a couple of trivial inefficiencies on 64 bits.
[ Impact: trivial performance enhancement, increase code similarity ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The 64-bit code already clears EFLAGS as soon as it has a stack. This
seems like a reasonable precaution, so do it on 32 bits as well.
[ Impact: extra paranoia ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Set up the decompression stack as soon as we know where it needs to
go. That way we have a full-service stack as soon as possible, rather
than relying on the BP_scratch field.
Note that the stack does need to be empty during bss zeroing (or
else the stack needs to be moved out of the bss segment, which is also
an option.)
[ Impact: cleanup, minor paranoia ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both on 32 and 64 bits, we copy all the way up to the end of bss,
except that on 64 bits there is a hack to avoid copying on top of the
page tables. There is no point in copying bss at all, especially
since we are just about to zero it all anyway.
To clean up and unify the handling, we now do:
- copy from startup_32 to _bss.
- zero from _bss to _ebss.
- the _ebss symbol is aligned to an 8-byte boundary.
- the page tables are moved to a separate section.
Use _bss as the copy endpoint since _edata may be misaligned.
[ Impact: cleanup, trivial performance improvement ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Clean up style issues in arch/x86/boot/compressed/head_64.S. This
file had a lot fewer style issues than its 32-bit cousin, but the ones
it has are worth fixing, especially since it makes the two files more
similar.
[ Impact: cleanup, no object code change ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reformat arch/x86/boot/compressed/head_32.S to be closer to currently
preferred kernel assembly style, that is:
- opcode and operand separated by tab
- operands separated by ", "
- C-style comments
This also makes it more similar to head_64.S.
[ Impact: cleanup, no object code change ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When generating the compression suffix in
arch/x86/boot/compressed/Makefile, follow standard Kbuild
conventions, that is:
- Use a dash not underscore before y/m/n endings
- Use := whenever possible.
Requested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Simplify the arch/x86/boot/compressed/Makefile, by using the new
capability of specifying multiple inputs to a compressor, and the
CONFIG_X86_NEED_RELOCS Kconfig symbol.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Aligning the .bss section makes it trivial to use large operation
sizes for moving the initialized sections and clearing the .bss.
The alignment chosen (L1 cache) is somewhat arbitrary, but should be
large enough to avoid all known performance traps and small enough to
not cause troubles.
[ Impact: trivial performance enhancement, future patch prep ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Look at the:
diff -u arch/x86/boot/compressed/vmlinux_*.lds
output and realize that they're basially exactly the same except for
trivial naming differences, and the fact that the 64-bit version has a
"pgtable" thing.
So unify them.
There's some trivial cleanup there (make the output format a Kconfig thing
rather than doing #ifdef's for it, and unify both 32-bit and 64-bit BSS
end to "_ebss", where 32-bit used to use the traditional "_end"), but
other than that it's really very mindless and straigt conversion.
For example, I think we should aim to remove "startup_32" vs "startup_64",
and just call it "startup", and get rid of one more difference. I didn't
do that.
Also, notice the comment in the unified vmlinux.lds.S talks about
"head_64" and "startup_32" which is an odd and incorrect mix, but that was
actually what the old 64-bit only lds file had, so the confusion isn't
new, and now that mixing is arguably more accurate thanks to the
vmlinux.lds.S file being shared between the two cases ;)
[ Impact: cleanup, unification ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Comment change only
The glove box is about avoiding problems with *registers* being
touched, not *memory*.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the video code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the MCA code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
