To be compliant with i915 display driver requirements, i915 power-up
must be done before any HDA communication takes place, including
parsing the bus capabilities. Otherwise the initial codec probe
may fail.
Move i915 initialization earlier in the SOF HDA sequence. This
sequence is now aligned with the snd-hda-intel driver where the
display_power() call is before snd_hdac_bus_parse_capabilities()
and rest of the capability parsing.
Also remove unnecessary ifdef around hda_codec_i915_init(). There's
a dummy implementation provided if CONFIG_SND_SOC_SOF_HDA is not
enabled.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200206200223.7715-3-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When HDA controller is resumed from suspend, i915 HDMI/DP
codec requires that following order of actions is kept:
- i915 display power up and configuration of link params
- hda link reset and setup
Current SOF HDA code delegates display codec power control
to the codec driver. This works most of the time, but in
runtime PM sequences, the above constraint may be violated.
On platforms where BIOS values for HDA link parameters do
not match hardware reset defaults, this may lead to errors
in HDA verb transactions after resume.
Fix the issue by explicitly powering the display codec
in the HDA controller resume/suspend calls, thus ensuring
correct ordering. Special handling is needed for the D0i3
flow, where display power must be turned off even though
DSP is left powered.
Now that we have more invocations of the display power helper
functions, the conditional checks surrounding each call have
been moved inside hda_codec_i915_display_power(). The two
special cases of display powering at initial probe are handled
separately. The intent is to avoid powering the display whenever
no display codecs are used.
Note that early powering of display was removed in
commit 687ae9e287 ("ASoC: intel: skl: Fix display power regression").
This change was also copied to the SOF driver. No failures
have resulted as hardware default values for link parameters
have worked out of the box. However with recent i915 driver
changes like done in commit 87c1694533 ("drm/i915: save
AUD_FREQ_CNTRL state at audio domain suspend"), this does not
hold anymore and errors are hit.
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200206200223.7715-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
jsl_desc missed default_fw_name, this will fail the probe in
nocodec or generice HDA mode due the firmware path is intel/sof/(null)
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200124213625.30186-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if DMA pages were successfully allocated in initialization
before calling free. For many types of memory (like sgbufs)
the extra free is harmless, but not all backends track allocation
state, so add an explicit check.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200124213625.30186-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The initial intent of releasing resources in the .remove does not work
well with HDaudio codecs. If the probe_continue() fails in a work
queue, e.g. due to missing firmware or authentication issues, we don't
release any resources, and as a result the kernel oopses during
suspend operations.
The suggested fix is to release all resources during errors in
probe_continue(), and use fw_state to track resource allocation
state, so that .remove does not attempt to release the same
hardware resources twice. PM operations are also modified so that
no action is done if DSP resources have been freed due to
an error at probe.
Reported-by: Takashi Iwai <tiwai@suse.de>
Co-developed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=1161246
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200124213625.30186-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It is possible to create invalid topology that will cause a kernel
Oops when trying to allocate buffers for a NULL substream.
Specifically such an Oops was caused by a topology, where a DAI on a
capture pipeline was referencing the PCM ID from a playback pipeline.
Fix the Oops by explicitly checking for NULL.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200124213625.30186-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change HDA probe behaviour slightly so that i915 power is not
turned off if i915 audio codecs are found in the initial probe done
by SOF Intel driver, and power is kept on until HDA codec driver
probe runs.
This will reduce number of mode sets on platforms with low
minimum CDCLK (like GLK) and brings the SOF probe sequence closer
to legacy HDA driver in terms of i915 audio codec power management.
BugLink: https://github.com/thesofproject/linux/issues/1642
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200120160117.29130-3-kai.vehmanen@linux.intel.com
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current interface to control i915 display power is misleading.
The hda_codec_i915_get() and hda_codec_i915_put() names suggest
a refcounting based interface. This is confusing as no refcounting
is done and the underlying HDAC library interface does not support
refcounts eithers.
Clarify the code by replacing the functions with a single
hda_codec_i915_display_power() that is aligned with
snd_hdac_display_power().
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200120160117.29130-2-kai.vehmanen@linux.intel.com
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4gVcMTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0IMOB/wJszUsDT3K46IvCg0qKJhsW+vsFsuo
bjk03Fsbi/v6ukcrIbRxBl50saqut8MFibSgrMTlDCkCOvQbz3C+S2N96N9SKWSX
gfEYd6PzdxVkZCx8xqybB82WGXjNBzoJue7lIYe2ytCIwjasPZtBjfNW9E+6KNkC
zOGoRLGSDepZRovDQM8JbALhKHw4z5a19fDOGiESuDfp3kjsTKAe8R+UXRvcsIDc
mqBblGMcKOZtRw87MDlDK2iKLPJEKAS3ndr6/a8+iX02hJMb3Yu6NbMmU4/0kHfC
3xc7xoyTZW8GVnhsLchJhOBaz+TFizTqBJTCr1tjkEjPB504SZm+/Wtx
=/nsR
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4h1RITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AjyB/41oCDts2pMZqxyt9PNBE3p4TDrRmxE
Ocbtn+ygKWCaqEX+Ecy8rPMtXEM1Ziz4o57+iOUWlpLd63uXDxBwF+t8+oXtbvCP
qfAO4IV7Fnw6CZTDvl5VFkSJKz+8woqP+ucqRIZSQLgqjuXXm26NVvZR93VY9av4
gdHregixNNxLk1lElp9ZKyos3FvhkAFf/Fl4oNEgAH/7mP8yj82sJPd/RQYiaeNu
t1vMC++Rh6cqt4X8gMWz8yET4LjqIWzQVMdyGJ9BP9mUtGUtuwK3kkQKpCpu1dMc
b2y1G5uUPFBT9bgIOWyPqXIqsqdBSauuD5/e1jCz2Tgeq961C47qAiBC
=khtD
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.5-rc6' into asoc-5.6
ASoC: Fixes for v5.5
This is mostly driver specific fixes, plus an error handling fix
in the core. There is a rather large diffstat for the stm32 SAI
driver, this is a very large but mostly mechanical update which
wraps every register access in the driver to allow a fix to the
locking which avoids circular locks, the active change is much
smaller and more reasonably sized.
Fix GCC warning with W=1, previous cleanup did not remove unnecessary
variable.
sound/soc/sof/intel/hda-dai.c: In function ‘hda_link_pcm_prepare’:
sound/soc/sof/intel/hda-dai.c:265:31: warning: variable ‘hda_stream’
set but not used [-Wunused-but-set-variable]
265 | struct sof_intel_hda_stream *hda_stream;
| ^~~~~~~~~~
Fixes: a3ebccb52e ("ASoC: SOF: Intel: hda: reset link DMA state in prepare")
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113205620.27285-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case system has multiple HDA controllers, it can happen that
same HDA codec driver is used for codecs of multiple controllers.
In this case, SOF may fail to probe the HDA driver and SOF
initialization fails.
SOF HDA code currently relies that a call to request_module() will
also run device matching logic to attach driver to the codec instance.
However if driver for another HDA controller was already loaded and it
already loaded the HDA codec driver, this breaks current logic in SOF.
In this case the request_module() SOF does becomes a no-op and HDA
Codec driver is not attached to the codec instance sitting on the HDA
bus SOF is controlling. Typical scenario would be a system with both
external and internal GPUs, with driver of the external GPU loaded
first.
Fix this by adding similar logic as is used in legacy HDA driver
where an explicit device_attach() call is done after request_module().
Also add logic to propagate errors reported by device_attach() back
to caller. This also works in the case where drivers are not built
as modules.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We will reinit DSP in a loop when it fails to initialize the first
time, as recommended. So, it is not an error before we finally give
up. And reorder the trace to make it more readable.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Any app using ALSA OSS emulation on top of SOF will fail
to error from OSS SNDCTL_DSP_SETFMT ioctl. Reported initially
as an issue with xournalpp (application using PortAudio with
an OSS backend), but applies more generally to other apps
using OSS as well.
Problem is caused by SOF PCM not supporting repeated calls
to hw_params(), without matching calls to pcm_free(). This
is however exactly what the ALSA OSS PCM code is doing when
it is handling the OSS ioctls.
The problem will lead to leaking of DSP resources and eventual
failure of DSP PCM_PARAMS IPC.
BugLink: https://github.com/thesofproject/linux/issues/1510
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200110235751.3404-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently have no trace referring to the firmware path, add a trace
to help debug cases where the wrong file might be used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200107160840.1524-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since ApolloLake, Intel platforms require signed firmware. On all
Windows platforms the default is to require the Intel production key
be used. But some platforms allow for a community key to be used,
which allows developers to compile/build their own firmware.
In the linux-firmware tree, the default intel/sof path is used for
firmwares signed for the production key, and files signed with the
community key are located in intel/sof/community.
Since we don't have an API to query which key is used on what
platforms, we have to rely on DMI-based quirks.
Developers can bypass this mechanism by setting a kernel 'fw_path'
module parameter. Additional dynamic debug traces are provided to help
debug cases where the wrong file might be used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200107160840.1524-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end - ptr.start + 1)
+ resource_size(&ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1577900990-8588-7-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
TGL supports more than three iDisp DAI's.
Add support for iDisp4 CPU DAI.
Without this patch, we saw the below error on our TGL DUT:
sof_rt5682 tgl_max98357a_rt5682: ASoC: CPU DAI iDisp4 Pin not registered
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220171037.10689-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dsp_box is used to keep DSP initiated messages. The value of dsp_offset
is set by the DSP with the first message, so we need a way to bootstrap
it in order to get the first message.
We do this by setting the correct default dsp_box offset which on i.MX8
is not zero.
Very interesting is why it has worked until now.
On i.MX8, DSP communicates with ARM core using a shared SDRAM memory
area. Actually, there are two shared areas:
* SDRAM0 - starting at 0x92400000, size 0x800000
* SDRAM1 - starting at 0x92C00000, size 0x800000
SDRAM0 keeps the data sections, starting with .rodata. By chance
fw_ready structure was placed at the beginning of .rodata.
dsp_box_base is defined as SDRAM0 + dsp_box_offset and it is placed
at the beginning of SDRAM1 (dsp_box_offset should be 0x800000). But
because it is zero initialized by default it points to SDRAM0 where
by chance the fw_ready was placed in the SOF firmware.
Anyhow, SOF commit 7466bee378dd811b ("clk: make freq arrays constant")
fw_ready is no longer at the beginning of SDRAM0 and everything shows
how lucky we were until now.
Fix this by properly setting the default dsp_box offset.
Fixes: 202acc565a ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191220170531.10423-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The memory allocation failure check for priv->pd_dev is incorrectly
pointer checking priv instead of priv->pd_dev. Fix this.
Addresses-Coverity: ("Logically dead code")
Fixes: 202acc565a ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204124816.1415359-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current structures are not well designed. We include Xtensa
information from the ACPI and PCI levels, but at the Kconfig/module
level everything Xtensa related is included at the sof/intel level.
Move the arch_ops under ops so that Xtensa is hidden in the DSP ops,
with a structure that follows the Kconfig/module partition.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case a HDA codec probe fails, do not raise error immediately,
but instead remove the codec from bus->codec_mask and continue
probe for other codecs.
This allows for more robust behaviour in cases where one codec
in the system is faulty. SOF driver load can still proceed with
the codecs that can be probed successfully. Probe may still
fail if suitable machine driver is not found, but in many
cases the generic HDA machine driver can operate with a subset
of codecs.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218002616.7652-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Log information about used compilator and optimization level
in sof firmware to host system.
It will be helful to catch some compiler dependent bugs.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218002616.7652-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a state machine for FW boot to track the
different stages of FW boot and replace the boot_complete
field with fw_state field in struct snd_sof_dev.
This will be used to determine the actions to be performed
during system suspend.
One of the main motivations for adding this change is the
fact that errors during the top-level SOF device probe cannot
be propagated and therefore suspending the SOF device normally
during system suspend could potentially run into errors.
For example, with the current flow, if the FW boot failed
for some reason and the system suspends, the SOF device
suspend could fail because the CTX_SAVE IPC would be attempted
even though the FW never really booted successfully causing it
to time out. Another scenario that the state machine fixes
is when the runtime suspend for the SOF device fails and
the DSP is powered down nevertheless, the CTX_SAVE IPC during
system suspend would timeout because the DSP is already
powered down.
Reviewed-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218002616.7652-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no known commercial devices using Haswell, and there is no
support for Haswell in SOF so remove remaining definitions and
structures.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The legacy IPC routines are only used by broadwell and baytrail
modules, import them as needed and make sure other modules cannot load
them.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191217202231.18259-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the PCM_PARAM IPC fails while configuring the FE, the kernel
oopses in the HDaudio link DMA .hw_free operation. The root cause is a
NULL dma_data since the BE .hw_params was never called by the SOC
core.
This error can also happen if the HDaudio link DMA configuration IPC
fails in the BE .hw_params.
This patches makes sure the dma_data is properly saved in .hw_params,
and tested before being use in hw_free.
GitHub issue: https://github.com/thesofproject/linux/issues/1417
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If sof_machine_check() fails during driver probe, the IPC
state is not initialized and this will lead to a NULL
dereference at driver unload. Example log is as follows:
[ 1535.980630] sof-audio-pci 0000:00:1f.3: error: no matching ASoC machine driver found - aborting probe
[ 1535.980631] sof-audio-pci 0000:00:1f.3: error: failed to get machine info -19
[ 1535.980632] sof-audio-pci 0000:00:1f.3: error: sof_probe_work failed err: -19
[ 1550.798373] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 1550.798393] Call Trace:
[ 1550.798397] snd_sof_ipc_free+0x15/0x30 [snd_sof]
[ 1550.798399] snd_sof_device_remove+0x29/0xa0 [snd_sof]
[ 1550.798400] sof_pci_remove+0x10/0x30 [snd_sof_pci]
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the drivers with the new managed buffer allocation API.
The superfluous snd_pcm_lib_malloc_pages() and
snd_pcm_lib_free_pages() calls are dropped.
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191211172019.23206-2-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
On Baytrail-CR, SSP0 needs to be used instead of SSP2. The
substitution is assumed to be done in the topology file.
When Baytrail-CR is detected, add -ssp0 suffix to the topology file
name so that the topology code picks up the correct file.
Tested on Asus T100TAF
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a module parameter 'codec_mask' to filter out unwanted
HDA codecs from driver probe. E.g. on most systems,
codec_mask=4 will limit to HDMI audio and exclude any
external HDA codecs.
Similar to 'probe_mask' module parameter of snd-hda-intel.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds into SOF topology the handling of ASRC DAPM type,
adds the tokens to configure the ASRC, and implement component IPC
into the driver.
Signed-off-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Turns out SSP 3-5 are only available on cht, to avoid dumping on
undefined registers let's split the definition.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An error occurs during parsing more than one ext_data from the mailbox, because
of invalid data offset handling. Fix by removing the incorrect duplicate
increment of the offset.
The return value is also reset in the switch case. This does not change the
behavior but improves readability - there is no longer a need to check what the
return value of get_ext_windows is.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Bartosz Kokoszko <bartoszx.kokoszko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Added warning log when found some unknown FW boot ext header,
to improve debuggability.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the drv_name and tplg_filename for nocodec
machine driver in sof_machine_check().
This means the sof_nocodec_setup() does not
need the mach, plat_data or desc arguments any longer.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This field is only set but never used. Let's remove
it to make code cleaner.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove nocodec_fw_filename from struct sof_dev_desc
as it is not longer needed.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, SOF probes machine drivers by creating a platform device
and passing the machine description as private data.
This is driven by the ACPI restrictions. Ideally, ACPI tables
should contain the description for the machine driver. This is
not possible because ACPI tables are frozen and used on multiple
OS-es (e.g Windows).
In the case of Device Tree we don't have this restriction, so we
choose to probe the machine drivers by creating a DT node as is
the standard ALSA way.
This patch makes the probing of machine drivers from SOF
core optional allowing for Device Tree platforms to decouple
the SOF core from machine driver probing.
Along with this, it also consolidates the machine driver selection
for Intel platforms by defining optional ops for selecting the machine
driver based on the ACPI match for HDA and non-HDA platforms and
setting the mach params.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191204211556.12671-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
