Understanding why of_phandle_iterator_next() returns an error can
sometimes be hard to decipher based solely on the error message, a
typical error example is that #foo-cells = <X> and the phandle property
used has a smaller number of cells specified, e.g.:
#thermal-sensor-cells = <1>;
phandle = <&scmi_sensor>
instead of:
phandle <&scmi_sensor 0>;
Instead, make it clear what the expectations are towards debugging
incorrect Device Tree faster:
OF: /thermal-zones/scmi-thermal: #thermal-sensor-cells = 1, found 0 instead
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Some SoCs have devices that are using a separate bus from the main bus to
perform DMA.
These buses might have some restrictions and/or different mapping than from
the CPU side, so we'd need to express those using the usual dma-ranges, but
using a different DT node than the node's parent.
Now that the generic interconnect bindings are available, we can model an
interconnect with the reserved name "dma-mem" for those use-cases.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The __of_translate_address function is used to translate the device tree
addresses to physical addresses using the various ranges property to create
the offset.
However, it's shared between the CPU addresses (based on the ranges
property) and the DMA addresses (based on dma-ranges). Since we're going to
add support for a DMA parent node that is not the DT parent node, we need
to change the logic a bit to have a callback function that will retrieve
the parent node we should use.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The __reserved_mem_init_node will call region specific reserved memory
init codes, but once all compatibled init codes failed, the memory region
will left in memory.reserved and cause leakage.
Take cma reserve memory DTS for example, if user declare 1MB size,
which is not align to (PAGE_SIZE << max(MAX_ORDER - 1,
pageblock_order)), rmem_cma_setup will return -EINVAL.
Meanwhile, rmem_dma_setup will also return -EINVAL since "reusable"
property is not set. If finally there is no reserved memory init pick up
this memory, kernel will left the 1MB leak in memory.reserved.
This patch will remove this kind of memory from memory.reserved, only
when __reserved_mem_init_node return neither 0 nor -ENOENT.
Signed-off-by: pierre Kuo <vichy.kuo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The node returned by of_graph_get_endpoint_by_regs has a reference taken,
and we need to put that reference back when done with the node.
However, the documentation for that node doesn't mention it, so let's make
sure it does.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Marc Gonzalez reported the following kmemleak crash:
Unable to handle kernel paging request at virtual address ffffffc021e00000
Mem abort info:
ESR = 0x96000006
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp = (____ptrval____) [ffffffc021e00000] pgd=000000017e3ba803, pud=000000017e3ba803, pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
Modules linked in:
CPU: 6 PID: 523 Comm: kmemleak Tainted: G S W 5.0.0-rc1 #13
Hardware name: Qualcomm Technologies, Inc. MSM8998 v1 MTP (DT)
pstate: 80000085 (Nzcv daIf -PAN -UAO)
pc : scan_block+0x70/0x190
lr : scan_block+0x6c/0x190
Process kmemleak (pid: 523, stack limit = 0x(____ptrval____))
Call trace:
scan_block+0x70/0x190
scan_gray_list+0x108/0x1c0
kmemleak_scan+0x33c/0x7c0
kmemleak_scan_thread+0x98/0xf0
kthread+0x11c/0x120
ret_from_fork+0x10/0x1c
Code: f9000fb4 d503201f 97ffffd2 35000580 (f9400260)
The crash happens when a no-map area is allocated in
early_init_dt_alloc_reserved_memory_arch(). The allocated region is
registered with kmemleak, but it is then removed from memblock using
memblock_remove() that is not kmemleak-aware.
Replacing memblock_phys_alloc_range() with memblock_find_in_range()
makes sure that the allocated memory is not added to kmemleak and then
memblock_remove()'ing this memory is safe.
As a bonus, since memblock_find_in_range() ensures the allocation in the
specified range, the bounds check can be removed.
[rppt@linux.ibm.com: of: fix parameters order for call to memblock_find_in_range()]
Link: http://lkml.kernel.org/r/20190221112619.GC32004@rapoport-lnx
Link: http://lkml.kernel.org/r/20190213181921.GB15270@rapoport-lnx
Fixes: 3f0c820664 ("drivers: of: add initialization code for dynamic reserved memory")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Prateek Patel <prpatel@nvidia.com>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The __memblock_alloc_base() function tries to allocate a memory up to
the limit specified by its max_addr parameter. Depending on the value
of this parameter, the __memblock_alloc_base() can is replaced with the
appropriate memblock_phys_alloc*() variant.
Link: http://lkml.kernel.org/r/1548057848-15136-9-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add debugfs support for dumping dma-debug information (Corentin Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
-----BEGIN PGP SIGNATURE-----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=nAMI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
- add debugfs support for dumping dma-debug information (Corentin
Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
Documentation/DMA-API-HOWTO: update dma_mask sections
sparc64/pci_sun4v: allow large DMA masks
sparc64/iommu: allow large DMA masks
sparc64: refactor the ali DMA quirk
ccio: allow large DMA masks
dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
dma-mapping: remove dma_mark_declared_memory_occupied
dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
dma-mapping: improve selection of dma_declare_coherent availability
dma-mapping: remove an incorrect __iommem annotation
of: select OF_RESERVED_MEM automatically
device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
mfd/sm501: depend on HAS_DMA
dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
dma-mapping: move debug configuration options to kernel/dma
dma-debug: add dumping facility via debugfs
dma: debug: no need to check return value of debugfs_create functions
videobuf2: replace a layering violation with dma_map_resource
dma-mapping: don't BUG when calling dma_map_resource on RAM
...
- Fix a unittest failure on UML. Preparation for converting to
kunit test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that
needs it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
-----BEGIN PGP SIGNATURE-----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=CnTd
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Fix a unittest failure on UML. Preparation for converting to kunit
test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that needs
it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
* tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: unittest: unflatten device tree on UML when testing
dt-bindings: Add vendor prefix for feiyang
dt-bindings: Add vendor prefix for techstar
dt-bindings: display: add missing semicolon in example
of: mark early_init_dt_alloc_reserved_memory_arch static
of: add dtc annotations functionality to dtx_diff
of: unittest: add caution to function header comment
of: unittest: remove report of expected error
dt-bindings: interrupt-controller: Convert ARM GICv3 to json-schema
dt-bindings: interrupt-controller: Convert ARM GIC to json-schema
dt-bindings: arm: l2x0: Convert L2 cache to json-schema
media: s5p-mfc: Fix memdev DMA configuration
dt-bindings: serial: sh-sci: Document r8a7778/9 HSCIF bindings
UML supports enabling OF, and is useful for running the device tree
tests, so add support for unflattening device tree blobs so we can
actually use it.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This function is only used in of_reserved_mem.c, and never overridden
despite the __weak marker.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rob Herring <robh@kernel.org>
This API is primarily used through DT entries, but two architectures
and two drivers call it directly. So instead of selecting the config
symbol for random architectures pull it in implicitly for the actual
users. Also rename the Kconfig option to describe the feature better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OF_RESERVED_MEM can be used if we have either CMA or the generic
declare coherent code built and we support the early flattened DT.
So don't bother making it a user visible options that is selected
by most configs that fit the above category, but just select it when
the requirements are met.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Name of function attach_node_and_children() is misleading because
if the node already exists in the livetree then only the node's
properties are attached. This works for the existing test data,
but add comment warning of this misleading name.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
update_node_properties() reports an error when the test data contains
a node (such as "/aliases") that already exists in the base devicetree.
The error is caused by of_fdt_unflatten_tree() autogenerating the
"name" property, thus both the existing node and the new node will
have a property with the same name. Suppress reporting the known
error.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having of_reserved_mem_device_init() forcibly reconfigure DMA for all
callers, potentially overriding the work done by a bus-specific
.dma_configure method earlier, is at best a bad idea and at worst
actively harmful. If drivers really need virtual devices to own
dma-coherent memory, they should explicitly configure those devices
based on the appropriate firmware node as they create them.
It looks like the only driver not passing in a proper OF platform device
is s5p-mfc, so move the rogue of_dma_configure() call into that driver
where it logically belongs.
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add an of_node_put when the result of of_graph_get_remote_port_parent is
not available.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@r exists@
local idexpression e;
expression x;
@@
e = of_graph_get_remote_port_parent(...);
... when != x = e
when != true e == NULL
when != of_node_put(e)
when != of_fwnode_handle(e)
(
return e;
|
*return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Now that all users of device_node.type pointer have been removed in
favor of accessor functions, we can remove it.
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull Devicetree updates from Rob Herring:
"The biggest highlight here is the start of using json-schema for DT
bindings. Being able to validate bindings has been discussed for years
with little progress.
- Initial support for DT bindings using json-schema language. This is
the start of converting DT bindings from free-form text to a
structured format.
- Reworking of initrd address initialization. This moves to using the
phys address instead of virt addr in the DT parsing code. This
rework was motivated by CONFIG_DEV_BLK_INITRD causing unnecessary
rebuilding of lots of files.
- Fix stale phandle entries in phandle cache
- DT overlay validation improvements. This exposed several memory
leak bugs which have been fixed.
- Use node name and device_type helper functions in DT code
- Last remaining conversions to using %pOFn printk specifier instead
of device_node.name directly
- Create new common RTC binding doc and move all trivial RTC devices
out of trivial-devices.txt.
- New bindings for Freescale MAG3110 magnetometer, Cadence Sierra
PHY, and Xen shared memory
- Update dtc to upstream version v1.4.7-57-gf267e674d145"
* tag 'devicetree-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (68 commits)
of: __of_detach_node() - remove node from phandle cache
of: of_node_get()/of_node_put() nodes held in phandle cache
gpio-omap.txt: add reg and interrupts properties
dt-bindings: mrvl,intc: fix a trivial typo
dt-bindings: iio: magnetometer: add dt-bindings for freescale mag3110
dt-bindings: Convert trivial-devices.txt to json-schema
dt-bindings: arm: mrvl: amend Browstone compatible string
dt-bindings: arm: Convert Tegra board/soc bindings to json-schema
dt-bindings: arm: Convert ZTE board/soc bindings to json-schema
dt-bindings: arm: Add missing Xilinx boards
dt-bindings: arm: Convert Xilinx board/soc bindings to json-schema
dt-bindings: arm: Convert VIA board/soc bindings to json-schema
dt-bindings: arm: Convert ST STi board/soc bindings to json-schema
dt-bindings: arm: Convert SPEAr board/soc bindings to json-schema
dt-bindings: arm: Convert CSR SiRF board/soc bindings to json-schema
dt-bindings: arm: Convert QCom board/soc bindings to json-schema
dt-bindings: arm: Convert TI nspire board/soc bindings to json-schema
dt-bindings: arm: Convert TI davinci board/soc bindings to json-schema
dt-bindings: arm: Convert Calxeda board/soc bindings to json-schema
dt-bindings: arm: Convert Altera board/soc bindings to json-schema
...
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Non-overlay dynamic devicetree node removal may leave the node in
the phandle cache. Subsequent calls to of_find_node_by_phandle()
will incorrectly find the stale entry. Remove the node from the
cache.
Add paranoia checks in of_find_node_by_phandle() as a second level
of defense (do not return cached node if detached, do not add node
to cache if detached).
Fixes: 0b3ce78e90 ("of: cache phandle nodes to reduce cost of of_find_node_by_phandle()")
Reported-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The phandle cache contains struct device_node pointers. The refcount
of the pointers was not incremented while in the cache, allowing use
after free error after kfree() of the node. Add the proper increment
and decrement of the use count.
Fixes: 0b3ce78e90 ("of: cache phandle nodes to reduce cost of of_find_node_by_phandle()")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
On architectures that only get their bootargs through devicetree's
chosen node (such as RISC-V), that node is mandatory. After a
discussion with Rob [1] I'm adding a warning in case chosen node
is not present, to let users know about it.
[1]: https://patchwork.ozlabs.org/patch/984224/#2016136
Signed-off-by: Nick Kossifidis <mick@ics.forth.gr>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
We've switched all users to nvmem_get_mac_address(). Remove the now
dead code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove directly accessing device_node.type pointer and use the accessors
instead. This will eventually allow removing the type pointer.
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Now that ARM64 uses phys_initrd_start/phys_initrd_size, we can get rid
of its custom __early_init_dt_declare_initrd() which causes a fair
amount of objects rebuild when changing CONFIG_BLK_DEV_INITRD. In order
to make sure ARM64 does not produce a BUG() when VM debugging is turned
on though, we must avoid early calls to __va() which is what
__early_init_dt_declare_initrd() does and wrap this around to avoid
running that code on ARM64.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that we have central and global variables holding the physical
address and size of the initrd, we can have
early_init_dt_check_for_initrd() populate
phys_initrd_start/phys_initrd_size for us.
This allows us to remove a chunk of code from arch/arm/mm/init.c
introduced with commit 65939301ac ("arm: set initrd_start/initrd_end
for fdt scan").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Now that there are no more users of path_component_name for Sparc
outside of the PDT code and all users of device_node.full_name are
converted to use "%pOF" printf specifier, we can align Sparc with FDT
and store just the base node name and unit address in full_name. This
makes path_component_name redundant, so it can be removed.
As full_name is used by printf specifiers, set it as early as possible.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add validation of NUMA distance map to prevent crashes with bad map
- Fix setting of dma_mask
-----BEGIN PGP SIGNATURE-----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=FThV
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- Add validation of NUMA distance map to prevent crashes with bad map
- Fix setting of dma_mask
* tag 'devicetree-fixes-for-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of, numa: Validate some distance map rules
of/device: Really only set bus DMA mask when appropriate
triggered by overlay release. The checks are intended to detect
possible memory leaks and invalid overlays.
The checks revealed bugs in existing code. Fixed the bugs.
While fixing bugs, noted other issues, which are fixed in
separate patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SQXe
-----END PGP SIGNATURE-----
Merge tag 'kfree_validate_v7-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/frowand/linux into dt/next
Pull overlay validation checks from Frank Rowand:
"Add checks to (1) overlay apply process and (2) memory freeing
triggered by overlay release. The checks are intended to detect
possible memory leaks and invalid overlays.
The checks revealed bugs in existing code. Fixed the bugs.
While fixing bugs, noted other issues, which are fixed in
separate patches."
Signed-off-by: Rob Herring <robh@kernel.org>
There are no users of of_pdt_build_more since 2012, so remove it.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Callers of of_irq_parse_one() blindly use the pointer args.np
without checking whether of_irq_parse_one() had an error and
thus did not set the value of args.np. Initialize args to
zero so that using the format "%pOF" to show the value of
args.np will show "(null)" when of_irq_parse_one() has an
error. This prevents the dereference of a random value.
Make the same fix for callers of of_parse_phandle_with_args()
and of_parse_phandle_with_args_map().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
One accessor of overlays[] was using a hard coded index value to
find the correct array entry instead of searching for the entry
containing the correct name.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
The overlay metadata nodes in the FDT created from testcases.dts
are not handled properly.
The __fixups__ and __local_fixups__ node were added to the live
devicetree, but should not be.
Only the first property in the /__symbols__ node was added to the
live devicetree if the live devicetree already contained a
/__symbols node. All of the node's properties must be added.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Overlay nodes added by add_changeset_node() do not have the node
fields name, phandle, and type set.
The node passed to __of_attach_node() when the add node changeset
entry is processed does not contain any properties. The node's
properties are located in add property changeset entries that will
be processed after the add node changeset is applied.
Set the node's fields in the node contained in the add node
changeset entry and do not set them to incorrect values in
add_changeset_node().
A visible symptom that is fixed by this patch is the names of nodes
added by overlays that have an entry in /sys/bus/platform/drivers/*/
will contain the unit-address but the node-name will be <NULL>, for
example, "fc4ab000.<NULL>". After applying the patch the name, in
this example, for node restart@fc4ab000 is "fc4ab000.restart".
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Argument unittest_nr is not used in of_unittest_apply_overlay(),
remove it.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Add test case of two fragments updating the same property. After
adding the test case, the system hangs at end of boot, after
after slub stack dumps from kfree() in crypto modprobe code.
Multiple overlay fragments adding, modifying, or deleting the same
property is not supported. Add check to detect the attempt and fail
the overlay apply.
Before this patch, the first fragment error would terminate
processing. Allow fragment checking to proceed and report all
of the fragment errors before terminating the overlay apply. This
is not a hot path, thus not a performance issue (the error is not
transient and requires fixing the overlay before attempting to
apply it again).
After applying this patch, the devicetree unittest messages will
include:
OF: overlay: ERROR: multiple fragments add, update, and/or delete property /testcase-data-2/substation@100/motor-1/rpm_avail
...
### dt-test ### end of unittest - 212 passed, 0 failed
The check to detect two fragments updating the same property is
folded into the patch that created the test case to maintain
bisectability.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Multiple overlay fragments adding or deleting the same node is not
supported. Replace code comment of such, with check to detect the
attempt and fail the overlay apply.
Devicetree unittest where multiple fragments added the same node was
added in the previous patch in the series. After applying this patch
the unittest messages will no longer include:
Duplicate name in motor-1, renamed to "controller#1"
OF: overlay: of_overlay_apply() err=0
### dt-test ### of_overlay_fdt_apply() expected -22, ret=0, overlay_bad_add_dup_node
### dt-test ### FAIL of_unittest_overlay_high_level():2419 Adding overlay 'overlay_bad_add_dup_node' failed
...
### dt-test ### end of unittest - 210 passed, 1 failed
but will instead include:
OF: overlay: ERROR: multiple overlay fragments add and/or delete node /testcase-data-2/substation@100/motor-1/controller
...
### dt-test ### end of unittest - 211 passed, 0 failed
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Multiple overlay fragments adding or deleting the same node is not
supported. An attempt to do so results in an incorrect devicetree.
The node name will be munged for the second add.
After adding this patch, the unittest messages will show:
Duplicate name in motor-1, renamed to "controller#1"
OF: overlay: of_overlay_apply() err=0
### dt-test ### of_overlay_fdt_apply() expected -22, ret=0, overlay_bad_add_dup_node
### dt-test ### FAIL of_unittest_overlay_high_level():2419 Adding overlay 'overlay_bad_add_dup_node' failed
...
### dt-test ### end of unittest - 210 passed, 1 failed
The incorrect (munged) node name "controller#1" can be seen in the
/proc filesystem:
$ pwd
/proc/device-tree/testcase-data-2/substation@100/motor-1
$ ls
compatible controller controller#1 name phandle spin
$ ls controller
power_bus
$ ls controller#1
power_bus_emergency
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Make overlay.c debug and error messages unique so that they can be
unambiguously found by grep.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
If overlay properties #address-cells or #size-cells are already in
the live devicetree for any given node, then the values in the
overlay must match the values in the live tree.
If the properties are already in the live tree then there is no
need to create a changeset entry to add them since they must
have the same value. This reduces the memory used by the
changeset and eliminates a possible memory leak.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Order the fields of struct fragment in the same order as
struct of_overlay_notify_data. The order in struct fragment is
not significant. If both structs are ordered the same then when
examining the data in a debugger or dump the human involved does
not have to remember which context they are examining.
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
When allocating a new node, add_changeset_node() was duplicating the
properties from the respective node in the overlay instead of
allocating a node with no properties.
When this patch is applied the errors reported by the devictree
unittest from patch "of: overlay: add tests to validate kfrees from
overlay removal" will no longer occur. These error messages are of
the form:
"OF: ERROR: ..."
and the unittest results will change from:
### dt-test ### end of unittest - 203 passed, 7 failed
to
### dt-test ### end of unittest - 210 passed, 0 failed
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
The changeset entry 'update property' was used for new properties in
an overlay instead of 'add property'.
The decision of whether to use 'update property' was based on whether
the property already exists in the subtree where the node is being
spliced into. At the top level of creating a changeset describing the
overlay, the target node is in the live devicetree, so checking whether
the property exists in the target node returns the correct result.
As soon as the changeset creation algorithm recurses into a new node,
the target is no longer in the live devicetree, but is instead in the
detached overlay tree, thus all properties are incorrectly found to
already exist in the target.
This fix will expose another devicetree bug that will be fixed
in the following patch in the series.
When this patch is applied the errors reported by the devictree
unittest will change, and the unittest results will change from:
### dt-test ### end of unittest - 210 passed, 0 failed
to
### dt-test ### end of unittest - 203 passed, 7 failed
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
There is a matching of_node_put() in __of_detach_node_sysfs()
Remove misleading comment from function header comment for
of_detach_node().
This patch may result in memory leaks from code that directly calls
the dynamic node add and delete functions directly instead of
using changesets.
This commit should result in powerpc systems that dynamically
allocate a node, then later deallocate the node to have a
memory leak when the node is deallocated.
The next commit will fix the leak.
Tested-by: Alan Tull <atull@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
The refcount of a newly added overlay node decrements to one
(instead of zero) when the overlay changeset is destroyed. This
change will cause the final decrement be to zero.
After applying this patch, new validation warnings will be
reported from the devicetree unittest during boot due to
a pre-existing devicetree bug. The warnings will be similar to:
OF: ERROR: memory leak before free overlay changeset, /testcase-data/overlay-node/test-bus/test-unittest4
This pre-existing devicetree bug will also trigger a WARN_ONCE() from
refcount_sub_and_test_checked() when an overlay changeset is
destroyed without having first been applied. This scenario occurs
when an error in the overlay is detected during the overlay changeset
creation:
WARNING: CPU: 0 PID: 1 at lib/refcount.c:187 refcount_sub_and_test_checked+0xa8/0xbc
refcount_t: underflow; use-after-free.
(unwind_backtrace) from (show_stack+0x10/0x14)
(show_stack) from (dump_stack+0x6c/0x8c)
(dump_stack) from (__warn+0xdc/0x104)
(__warn) from (warn_slowpath_fmt+0x44/0x6c)
(warn_slowpath_fmt) from (refcount_sub_and_test_checked+0xa8/0xbc)
(refcount_sub_and_test_checked) from (kobject_put+0x24/0x208)
(kobject_put) from (of_changeset_destroy+0x2c/0xb4)
(of_changeset_destroy) from (free_overlay_changeset+0x1c/0x9c)
(free_overlay_changeset) from (of_overlay_remove+0x284/0x2cc)
(of_overlay_remove) from (of_unittest_apply_revert_overlay_check.constprop.4+0xf8/0x1e8)
(of_unittest_apply_revert_overlay_check.constprop.4) from (of_unittest_overlay+0x960/0xed8)
(of_unittest_overlay) from (of_unittest+0x1cc4/0x2138)
(of_unittest) from (do_one_initcall+0x4c/0x28c)
(do_one_initcall) from (kernel_init_freeable+0x29c/0x378)
(kernel_init_freeable) from (kernel_init+0x8/0x110)
(kernel_init) from (ret_from_fork+0x14/0x2c)
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
