Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
Due to a confusion I thought that eth_type_trans() was called by the
network stack whereas it can actually be called by network drivers to
figure out the skb protocol and next packet_type handlers.
In light of the above, it is not safe to store the frame type from the
DSA tagger's .filter callback (first entry point on RX path), since GRO
is yet to be invoked on the received traffic. Hence it is very likely
that the skb->cb will actually get overwritten between eth_type_trans()
and the actual DSA packet_type handler.
Of course, what this patch fixes is the actual overwriting of the
SJA1105_SKB_CB(skb)->type field from the GRO layer, which made all
frames be seen as SJA1105_FRAME_TYPE_NORMAL (0).
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
In case a call to dsa_tree_setup() fails, an attempt to cleanup is made
by calling dsa_tree_remove_switch(), which should take care of
removing/unregistering any resources previously allocated. This does not
happen because it is conditioned by dst->setup being true, which is set
only after _all_ setup steps were performed successfully.
This is especially interesting when the internal MDIO bus is registered
but afterwards, a port setup fails and the mdiobus_unregister() is never
called. This leads to a BUG_ON() complaining about the fact that it's
trying to free an MDIO bus that's still registered.
Add proper error handling in all functions branching from
dsa_tree_setup().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tools like tcpdump need to be able to decode the significance of fake
VLAN headers that DSA uses to separate switch ports.
But currently these have no global significance - they are simply an
ordered list of DSA_MAX_SWITCHES x DSA_MAX_PORTS numbers ending at 4095.
The reason why this is submitted as a fix is that the existing mapping
of VIDs should not enter into a stable kernel, so we can pretend that
only the new format exists. This way tcpdump won't need to try to make
something out of the VLAN tags on 5.2 kernels.
Fixes: f9bbe4477c ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.1Q tagging performs an unbalanced setup in terms of RX VIDs on
the CPU port. For the ingress path of a 802.1Q switch to work, the RX
VID of a port needs to be seen as tagged egress on the CPU port.
While configuring the other front-panel ports to be part of this VID,
for bridge scenarios, the untagged flag is applied even on the CPU port
in dsa_switch_vlan_add. This happens because DSA applies the same flags
on the CPU port as on the (bridge-controlled) slave ports, and the
effect in this case is that the CPU port tagged settings get deleted.
Instead of fixing DSA by introducing a way to control VLAN flags on the
CPU port (and hence stop inheriting from the slave ports) - a hard,
perhaps intractable problem - avoid this situation by moving the setup
part of the RX VID on the CPU port after all the other front-panel ports
have been added to the VID.
Fixes: f9bbe4477c ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For DSA switches that do not have an .adjust_link callback, aka those
who transitioned totally to the PHYLINK-compliant API, use PHYLINK to
drive the CPU/DSA ports.
The PHYLIB usage and .adjust_link are kept but deprecated, and users are
asked to transition from it. The reason why we can't do anything for
them is because PHYLINK does not wrap the fixed-link state behind a
phydev object, so we cannot wrap .phylink_mac_config into .adjust_link
unless we fabricate a phy_device structure.
For these ports, the newly introduced PHYLINK_DEV operation type is
used and the dsa_switch device structure is passed to PHYLINK for
printing purposes. The handling of the PHYLINK_NETDEV and PHYLINK_DEV
PHYLINK instances is common from the perspective of the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.
These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sk_buff control block can have any contents on xmit put there by the
stack, so initialization is mandatory, since we are checking its value
after the actual DSA xmit (the tagger may have changed it).
The DSA_SKB_ZERO() macro could have been used for this purpose, but:
- Zeroizing a 48-byte memory region in the hotpath is best avoided.
- It would have triggered a warning with newer compilers since
__dsa_skb_cb contains a structure within a structure, and the {0}
initializer was incorrect for that purpose.
So simply remove the DSA_SKB_ZERO() macro and initialize the
deferred_xmit variable by hand (which should be done for all further
dsa_skb_cb variables which need initialization - currently none - to
avoid the performance penalty).
Fixes: 97a69a0dea ("net: dsa: Add support for deferred xmit")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix gcc build error:
net/dsa/tag_brcm.c:211:16: error: brcm_prepend_netdev_ops undeclared here (not in a function); did you mean brcm_netdev_ops?
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
^
./include/net/dsa.h:708:10: note: in definition of macro DSA_TAG_DRIVER
.ops = &__ops, \
^~~~~
./include/net/dsa.h:701:36: warning: dsa_tag_driver_brcm_prepend_netdev_ops defined but not used [-Wunused-variable]
#define DSA_TAG_DRIVER_NAME(__ops) dsa_tag_driver ## _ ## __ops
^
./include/net/dsa.h:707:30: note: in expansion of macro DSA_TAG_DRIVER_NAME
static struct dsa_tag_driver DSA_TAG_DRIVER_NAME(__ops) = { \
^~~~~~~~~~~~~~~~~~~
net/dsa/tag_brcm.c:211:1: note: in expansion of macro DSA_TAG_DRIVER
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
Like the CONFIG_NET_DSA_TAG_BRCM case,
brcm_prepend_netdev_ops and DSA_TAG_PROTO_BRCM_PREPEND
should be wrappeed by CONFIG_NET_DSA_TAG_BRCM_PREPEND.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b74b70c449 ("net: dsa: Support prepended Broadcom tag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().
The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.
However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.
Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.
This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.
The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).
One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.
There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).
Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>-
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if VLAN filtering is global, DSA will call this callback once per
each port. Drivers should not have to compare the global state with the
requested change. So let DSA do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are standalone (after they left the bridge), they should have
no VLAN filtering semantics (they should pass all traffic to the CPU).
Currently this is not true for switchdev drivers, because the bridge
"forgets" to unset that.
Normally one would think that doing this at the bridge layer would be a
better idea, i.e. call br_vlan_filter_toggle() from br_del_if(), similar
to how nbp_vlan_init() is called from br_add_if().
However what complicates that approach, and makes this one preferable,
is the fact that for the bridge core, vlan_filtering is a per-bridge
setting, whereas for switchdev/DSA it is per-port. Also there are
switches where the setting is per the entire device, and unsetting
vlan_filtering one by one, for each leaving port, would not be possible
from the bridge core without a certain level of awareness. So do this in
DSA and let drivers be unaware of it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the CONFIG symbols tristate and add help text.
The broadcom and Microchip KSZ tag drivers support two different
tagging protocols in one driver. Add a configuration option for the
drivers, and then options to select the protocol.
Create a submenu for the tagging drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
tab/space cleanup
Help text wording
NET_DSA_TAG_BRCM_COMMON and NET_DSA_TAG_KZS_COMMON hidden
v3:
More tabification
Punctuation
v4:
trailler->trailer
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the driver is compiled with both
CONFIG_NET_DSA_TAG_BRCM and CONFIG_NET_DSA_TAG_BRCM_PREPEND disabled.
This results in warnings about unused symbols. Add some conditional
compilation to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Reorder patch to before tag drivers can be modules
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the _get and _put functions to make use of the list of tag
drivers. Also, trigger the loading of the module, based on the alias
information. The _get function takes a reference on the tag driver, so
it cannot be unloaded, and the _put function releases the reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Make tag_driver_register void
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver is unloaded, the lock on the tag driver
should be released so the module can be unloaded. Add the needed calls,
but leave the actual release code as a stub.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_resolve_tag_protocol() is used to find the tagging driver needed
by a switch driver. When the tagging drivers become modules, it will
be necassary to take a reference on the module to prevent it being
unloaded. So rename this function to _get() to indicate it has some
locking properties.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The none tagger is special in that it does not live in a tag_*.c file,
but is within the core. Register/unregister when DSA is
loaded/unloaded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the tag drivers register themselves with the DSA core, keeping
them in a linked list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the tag drivers are some variant of GPL. Add a MODULE_LICENSE()
indicating this, so the drivers can later be compiled as modules.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tag drivers become modules, we will need to dynamically load
them based on what the switch drivers need. Add aliases to map between
the TAG protocol and the driver.
In order to do this, we need the tag protocol number as something
which the C pre-processor can stringinfy. Only the compiler knows the
value of an enum, CPP cannot use them. So add #defines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an SPDX header, and remove the license boilerplate text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get(). Leave
ndo_get_port_parent_id implementation only for legacy.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flow_dissect for qca tagged packet to get the right hash.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since each non-legacy slave has its own devlink port instance
correctly set, rely on devlink core to generate correct phys port name.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for devlink compat functions to work, implement
ndo_get_devlink_port. Legacy slaves does not have devlink port instances
created for themselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phylink_of_phy_connect fails, dsa_slave_phy_setup tries to save the
day by connecting to an alternative PHY, none other than a PHY on the
switch's internal MDIO bus, at an address equal to the port's index.
However this does not take into consideration the scenario when the
switch that failed to probe an external PHY does not have an internal
MDIO bus at all.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since attrs are static during the existence of devlink port, set the
before registration of the port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink functions are in use, so include the related header file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were skipping the prepare phase which causes some problems with at
least a couple of drivers:
- mv88e6xxx chooses to skip programming VID = 0 with -EOPNOTSUPP in
the prepare phase, but we would still try to force this VID since we
would only call the commit phase and so we would get the driver to
return -EINVAL instead
- qca8k does not currently have a port_vlan_add() callback implemented,
yet we would try to call that unconditionally leading to a NPD
Fix both issues by conforming to the current model doing a
prepare/commit phase, this makes us consistent throughout the code and
assumptions.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Michal Vokáč <michal.vokac@ysoft.com>
Fixes: 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes. The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted all possible callers to using a switchdev
notifier for attributes we do not have a need for implementing
switchdev_ops anymore, and this can be removed from all drivers the
net_device structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.
Prepare DSA to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
dsa_slave_port_attr_set() can process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being able to build devlink as a module causes growing pains.
First all drivers had to add a meta dependency to make sure
they are not built in when devlink is built as a module. Now
we are struggling to invoke ethtool compat code reliably.
Make devlink code built-in, users can still not build it at
all but the dynamically loadable module option is removed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support VLAN filtering being enabled/disabled on a
bridge, while having other ports being non bridge port members, we need
to support the ndo_vlan_rx_{add,kill}_vid callbacks in order to make
sure the non-bridge ports can continue receiving VLAN tags, even when
the switch is globally configured to do ingress/egress VID checking.
Since we can call dsa_port_vlan_{add,del} with a bridge_dev pointer
NULL, we now need to check that in these two functions.
We specifically deal with two possibly problematic cases:
- creating a bridge VLAN entry while there is an existing VLAN device
claiming that same VID
- creating a VLAN device while there is an existing bridge VLAN entry
with that VID
Those are both resolved with returning -EBUSY back to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN devices on top of a DSA network device which is already part of a
bridge and with said bridge being VLAN aware should not be allowed to be
enslaved into that bridge. For one, this duplicates functionality
offered by the VLAN aware bridge which supports tagged and untagged VLAN
frames processing and it would make things needlessly complex to e.g.:
propagate FDB/MDB accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the bridge no longer calling switchdev_port_attr_get() to obtain
the supported bridge port flags from a driver but instead trying to set
the bridge port flags directly and relying on driver to reject
unsupported configurations, we can effectively get rid of
switchdev_port_attr_get() entirely since this was the only place where
it was called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bridge code and the drivers to check for
bridge port(s) flags at the time we try to set them, there is no need
for a get() -> set() sequence anymore and
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for removing SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT,
add support for a function that processes the
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS and
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attributes and returns not
supported for any flag set, since DSA does not currently support
toggling those bridge port attributes (yet).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches work by learning the MAC address for each attached station by
monitoring traffic from each station. When a station sends a packet,
the switch records which port the MAC address is connected to.
With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4. The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.
With IPv6 networking, the situation is rather different. Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted. This multicast needs to reach the intended
station in order for the neighbour to be discovered.
Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale. This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.
Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports. As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network. However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.
The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.
This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge. This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed. However, the Linux bridge code believes that
the port is in disabled mode.
If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode. If it is brought up and then added to the bridge,
it will be in disabled mode.
This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge. Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.
Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA. See
e47172ab7e ("rocker: put port in FORWADING state after leaving bridge")
Fixes: b73adef677 ("net: dsa: integrate with SWITCHDEV for HW bridging")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPS not work for DSA devices since the 'skb_get_hash'
will always get the invalid hash for dsa tagged packets.
"[PATCH] tag_mtk: add flow_dissect callback to the ops struct"
introduced the flow_dissect callback to get the right hash for
MTK tagged packet. Tag_dsa and tag_edsa also need to implement
the callback.
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unbalance of master's promiscuity or allmulti will happen after ifdown
and ifup a slave interface which is in a bridge.
When we ifdown a slave interface , both the 'dsa_slave_close' and
'dsa_slave_change_rx_flags' will clear the master's flags. The flags
of master will be decrease twice.
In the other hand, if we ifup the slave interface again, since the
slave's flags were cleared the 'dsa_slave_open' won't set the master's
flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if'
will set the master's flags. The flags of master is increase once.
Only propagating flag changes when a slave interface is up makes
sure this does not happen. The 'vlan_dev_change_rx_flags' had the
same problem and was fixed, and changes here follows that fix.
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous change tries to set the MTU on the master device to take
into account the DSA overheads. This patch tries to reset the master
device back to the default MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA tagging of frames sent over the master interface to the switch
increases the size of the frame. Such frames can then be bigger than
the normal MTU of the master interface, and it may drop them. Use the
overhead information from the tagger to set the MTU of the master
device to include this overhead.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each DSA tag protocol needs to add additional headers to the Ethernet
frame in order to direct it towards a specific switch egress port. It
must also remove the head from a frame received from a
switch. Indicate the maximum size of these headers in the tag protocol
ops structure, so the core can take these overheads into account.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While introducing the DSA tagging protocol attribute, it was added to the DSA
slave network devices, but those actually see untagged traffic (that is their
whole purpose). Correct this mistake by putting the tagging sysfs attribute
under the DSA master network device where this is the information that we need.
While at it, also correct the sysfs documentation mistake that missed the
"dsa/" directory component of the attribute.
Fixes: 98cdb48071 ("net: dsa: Expose tagging protocol to user-space")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an explicit check in rocker_world_port_obj_vlan_add(),
dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects
that are added to a device that is not a front-panel port device are
ignored. Therefore this check is immaterial.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of
this field from all clients, which were migrated to use switchdev
notification in the previous patches.
Add a new function switchdev_port_obj_notify() that sends the switchdev
notifications SWITCHDEV_PORT_OBJ_ADD and _DEL.
Update switchdev_port_obj_del_now() to dispatch to this new function.
Drop __switchdev_port_obj_add() and update switchdev_port_obj_add()
likewise.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
DSA currently doesn't support any other uppers than bridge.
SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on
the bridge port device. Thus the only case that a stacked device could
be validly referenced by port object notifications are bridge
notifications for VLAN objects added to the bridge itself. But the
driver explicitly rejects such notifications in dsa_port_vlan_add(). It
is therefore safe to assume that the only interesting case is that the
notification is on a front-panel port netdevice. Therefore keep the
filtering by dsa_slave_dev_check() in place.
To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to rocker_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
