To optimize the current consumption we use pm_runtime autosuspend
functions which execute the pm_runtime_suspend after a delay of
inactivity on the other hand we use pm_runtime_resume every time
we receive an interruption to wake up the pm2301.
Signed-off-by: M BenZoubeir <mustapha.ben.zoubeir-xsig@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: M BenZoubeir <mustapha.ben.zoubeir-xsig@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
When the state of USB Charge detection is changed then the calls
use a define for another register in other bank. This change
creates a new define for the correct register and removes the
magic numbers that are present.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Timers used for charging safety and maintenance must work even when
CPU power has collapsed. By using hrtimers with the realtime clock
the system is able to trigger an alarm that wakes-up the CPU and makes
it possible to handle events.
Allow a little slack time of 5 minutes for the hrtimers to allow CPU
to be woken-up in a more optimal power saving way. A 5 minute delay
to time-out timers relative to hours does not impact on safety.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Charging watchdog kicker work-thread gets started twice causing
'failed to kick watchdog' message after removing charger and
when re-inserting charger. This patch removes the superfluous
start of watchdog kicker-thread.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newer AB's such as the AB8505, AB9540 etc include a
USBLink1 Status register which detects a larger range of
external devices. This should be used instead of the
USBLine Status register.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Yang QU <yang.qu@stericsson.com>
Provide AB8540 platform specific information required to run the
Battery Management subsystem on AB8540 based devices. For this to
happen we see the introduction of separate platform specific data
structures and a means in which to process them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Due to btemp filtering enabled during init, temp values reported
to charge algorithm driver started from 0. As a result,charge
algorithm was going into wrong state and charging was stopped.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Martin SJOBLOM <martin.w.sjoblom@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
AB8540 supports power path function in USB charging mode for fast
power up with dead and weak battery, and it could extend
the battery age.
When USB charging starts, if the Vbattrue is below than SW cut off
voltage, power path and pre-charge should be enabled. If Vbattrue
is higher than SW cut off voltage, power path and pre-charge should
be disabled. This is to make sure full current to battery charge.
At the end of charge, power path should be enable again to reduce
charging the battery again.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PM2301 Charger should always be available when using the AB8500
Battery Management system, we're ensuring this will be the case.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
The AB8505 does not have the same address for USB link-status
as has ab8500. Add AB8505_USB_LINK_STATUS and code to switch
to correct constant.
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
When battery capacity was going below 1% fg is not supposed
to report 0% unless we've got the LOW_BAT IRQ, no matter
what the FG-algorithm says. This made fg get stuck at 1% if
charger is connected when capacity is 1%.
Signed-off-by: Hakan BERG <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Battery tempreature readings sometimes fail and results in
a value far from recent values. This patch adds a software
filter that disposes such readings, by allowing direct
updates on temperature only if two samples result in the
same temperature. Else only allow 1 degree change from previous
reported value in the direction of the new measurement.
Signed-off-by: Hakan Berg <hakan.berg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Martin SJOBLOM <martin.w.sjoblom@stericsson.com>
Reviewed-by: Rabin VINCENT <rabin.vincent@stericsson.com>
When in suspend state, upon plug-in of external AC charger the
device needs to wake-up and charging operation started.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
This patch adds support for die temperature thermal protection
in pm2301 driver.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Hakan BERG <hakan.berg@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Do not set higher current in stepping functionality if VBUS is dropping.
After VBUS has dropped try to set current once again. If dropping again
then we have found the maximum capability of the charger.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mustapha Ben Zoubeir <mustapha.ben.zoubeir-nonst@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Olivier CLERGEAUD <olivier.clergeaud@stericsson.com>
Force main charger detect in turn on status.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Added support for main charger over voltage protection.
Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Due to a bug in some AB8500 ASICs charger removal cannot always
be detected if the removal and reinsertion is done to close in time.
This patch detects above described case and handles the situation
so that charging will be kept turned on.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add 2.7v, 2.9v, 3.0v, 3.2v and 3.3v charging voltages for backup
battery. Before that only 2.5v, 2.6v, 2.8v, 3.1v were available.
Signed-off-by: Yang QU <yang.qu@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Xiao Mei ZHANG <xiaomei.zhang@stericsson.com>
Unscaled capacity should be reported for POWER_SUPPLY_PROP_CAPACITY.
Signed-off-by: Martin Bergstrom <martin.bergstrom@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Add support for a power cut feature which allows user to
configure when ab8505 and ab8540 based platforms should shut
down system due to low battery.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Any platform can be dynamically probed for model and version number
provided the AB8500 MFD parent device pointer is available. This
patch obtains that pointer and stores it in a locally controlled
struct for later use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
End of charging is managed by SW.
Signed-off-by: Rajkumar Kasirajan <rajkumar.kasirajan@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Tested-by: Jonas ABERG <jonas.aberg@stericsson.com>
Just lots of white space corrections, changing some of the 4 space
tabs to 8 and pulling back some of the double tabbing back into
singles, such as the remaining of the driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Make use of the hierarchical interrupt rergister called
ITLatchHier1 - 3 also for the 8500 platform (currently the
hierarchical interrupt registers are used only for the 8540
and 9540 platforms). This will make the interrupt routing
go faster since fewer i2c reads need to made in the most
common cases.
Signed-off-by: Dariusz Szymczak <dariusz.xd.szymczak@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mian Yousaf KAUKAB <mian.yousaf.kaukab@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Use kstrtoul_from_user for getting an unsigned long from userspace
which is less error prone.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
As I am working on SPARSE_IRQ a number of implicit resource
grabs in the kernel become evident. For example, some includes
like <linux/irqs.h> would implicitly include <mach/irqs.h>
and then from there <mach/db8500-regs.h>.
In many cases it is masking the fact that drivers do not
properly use resources to pass their dependencies, base
addresses etc. So write explicit #include statements with
TODO items to have this fixed the proper way to all drivers
doing this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Hierarchically, the abx500-clk shall be considered as a child of the
ab8500 core. The abx500-clk is intiated at arch init and thus the clks
will be available when clients needs them.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Reviewed-by: Patrice CHOTARD <patrice.chotard@stericsson.com>
Reviewed-by: Gabriel FERNANDEZ <gabriel.fernandez@stericsson.com>
Reviewed-by: Philippe BEGNIC <philippe.begnic@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Required to read out correct debug information from the AB chip.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Enable group write permissions for ab8500 debug MFD driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Several states can be detected when a device is initially turned on.
This patch displays these states in the log. If none of the states
are true, then we report that too.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Yang QU <yang.qu@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Alexandre BOURDIOL <alexandre.bourdiol@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to dump the SIM registers from debugfs. It will
temporary change the config to allow APE side to read the SIM registers.
Note that this read can cause problem on modem side since the modem
can't read these registers while the operation is ongoing.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
So we're removing support for it.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add VBUS_DET_R, VBUS_DET_F IRQ, ID_DET_PLUGR and ID_DET_PLUGF IRQ
information to ab8505_iddet_resources. These are required to get
interrupts for AB8505 cut-2.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Optimise GPADC driver:
* for code readability and maintenance by grouping similar cheking
* for performance by grouping several writing to control register
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Allow GPADC debug information to be shown when executing on an AB8540
based platform.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@stericsson.com>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This patch enables the GPADC to work on AB8540 based platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add a new reset function which uses the AB WD with 0 timeout.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Make it possible to dump all registers in ab8505 and ab9540.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add error checks to see if sysctrl was probed as it should.
If the sysctrl_dev is not set the return value is -EINVAL.
Signed-off-by: Marcus Danielsson <marcus.danielsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Tested-by: Per FORLIN <per.forlin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add information regarding what ab interrupt that caused
a wake-up from suspend in <debugfs>/ab8500/interrupts.
Also print the name of the interrupts, not just the numbers.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Per FORLIN <per.forlin@stericsson.com>
Tested-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Stop trying to read i2c registers if one fail.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
ITSource/ITLatch 7, 8, 9 and 10 don't exist on AB8540. This patch
replaces them with '-1' in the interrupt list, and handles the '-1'
in the code accordingly.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
