This patch adds GB speed support for QSFP+ modules.
Autonegotiation is not supported with QSFP+. The user will have to set
the desired speed on both link partners using ethtool advertise setting.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the possible use of uninitialized memory by checking the
return value on eeprom reads. These issues were identified by static
analysis. In many cases error messages will be produced so that corrupted
eeprom issues will be more visible.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue with the 82599 adapter where it can potentially keep
link lights up when the adapter has gone down. The patch adds a function which
ensures link is disabled, and calls this function when the adapter transitions
to a down state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a x520 based quad-port (4x10Gbps) NIC with a single QSFP+
connector. Changes were required to our identify functions due to
different eeprom address which is also included here.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for a new media type fiber_fixed. This is useful
to avoid all the SFP+ hot plug support path on devices who's fix fiber need
not worry about such things. This patch is needed for a following patch
that adds support for "fiber_fixed" devices.
v2: cleaned up logging message based on feedback from David Miller
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for disabling link during boot time. This
feature was requested by customers and is configurable through the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes majority of the AUTOC register reads by using a cached
value instead.
The reason for this change is to avoid writing corrupted values to AUTOC
due to bad FW.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds LX support to 82599 devices. This is an alternate patch to
the one suggested by Stefan Behte <s.behte@babiel.com>
In addition this patch includes some cleanups such as:
- removed parenthesis around "x == y ||" lines inside an if statement for
consistency.
- grouped the sx/lx sfp types along with srlr in ixgbe_get_settings() since
they all have the same supported, advertised and port values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Stefan Behte <s.behte@babiel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The variable wol_supported really is just checking whether it is enabled, rather
than whether it is supported. If it is enabled it will be supported, but this
does not necessarily hold true the other way around. This patch renames the
variable to avoid confusion.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We reset during the shutdown path which will reset AUTOC register. This
would change LMS to 10G. If we were currently linked at 1G we will lose
link, which is a bad thing if we wanted WoL to work. For the fix I needed
to know if WoL is supported so I created a new bool in the ixgbe_hw struct.
If this is set we will not allow the reset to change the current LMS value
in AUTOC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were only turning the laser on when the adapter was up. This
causes issues for those who wanted to access the MNG FW while the
port was in a down state. This patch makes sure the laser is turned
on in probe and remain up even after the port is brought down.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.
Based on original patch from Aurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the autoneg parameter from the setup_link functions.
Adds local variable autoneg to setup_link functions to be passed
to get_link_capabilities functions if needed.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Removes the autoneg parameter from the setup_link_speed functions. These
functions do nothing with this parameter.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the normal kernel test instead of a module specific one.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline
reset on all 82599 devices. This is necessary to avoid possible link issues.
Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap
all AUTOC writes when LESM is enabled.
v2- fix LMS behaviour based on feedback by Martin Josefsson
CC: Martin Josefsson <gandalf@mjufs.se>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function that forces a full pipeline reset. This
function will be used in following patches to completely reset the PHY
during resets.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The loop in ixgbe_reinit_fdir_tables_82599() only polls for up to 100us
resulting in failures to update the FDIR filter table at 1Gbps and 10Gbps
when under load.
The poll times for FDIRCTRL.INIT_DONE are 55us, 550us and 5.5ms for 10Gbps,
1Gbps and 100Mbps respectively.
This patch sets the wait time to be the same as in ixgbe_fdir_enable_82599()
Reported-by: Bhushan <shashi-sm@users.sf.net>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Sascha Wildner <saw@online.de>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue in which an FCoE enabled adapter was always
setting the FCoE SAN MAC MPSAR register to 0x1. This results in the first
VF being assigned the SAN MAC address in the case of SR-IOV and as such is
incorrect. To resolve this I am adding a new function that will update the
SAN MAC pool address after reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 1G Fiber PHY modules (SFP+ modules). This support
comes along side support for 1G Copper PHY modules, but uses a different PHY
type (ixgbe_sfp_type_1g_sx_core).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have thermal data available, this patch exports
this data via hwmon sysfs interface.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a race condition in the reset path where the RX buffer
could become corrupted during Fdir configuration.This is due to
a HW bug.The fix right now is to lock the buffer while we do the
fdir configuration.Since we were using similar workaround for another bug,
I moved the existing code to a function and reused it.HW team also recommended
that IXGBE_MAX_SECRX_POLL value be changed from 30 to 40.The erratum for this
bug will be published in the next release 82599 Spec Update
Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is clearly a typeo where we are not checking the return value from
get_link_capabilities but should. This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New year so bump the copyright date.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support for new 82599 based quad port adapter.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
82598 and 82599 do not ship with this type of PHY
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for new device ID.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to avoid a hardware lockup when Tx work is still
pending and we request a reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The reset paths are overly complicated and are either missing steps or
contain extra unnecessary steps such as reading MAC address twice. This
change is meant to help clean up the reset paths an get things functioning
correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The packet buffer is correctly allocated by generic pb allocation
path in ixgbe_configure() there is no need to do the allocation
here as well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
