This adds and enable the operating points that have been tested and are
currently supported by the SoC. This also adds clocks for ARMCLKL and
ARMCLKB.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently we are assigning mic irq to rt5514 i2c driver, which is wrong.
Assign it to rt5514 spi driver instead.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We need to init vop aclk and hclk incase the U-Boot does not do
the initialize.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms".
Fixes: 48f4d9796d (arm64: dts: rockchip: add Gru/Kevin DTS)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.
This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.
Fixes: 8164a84cca ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch updates the dynamic-power-coefficient for big cluster on
rk3399 SoCs.
The dynamic power consumption of the CPU is proportional to the square of
the Voltage (V) and the clock frequency (f). The coefficient is used to
calculate the dynamic power as below -
Pdyn = dynamic-power-coefficient * V^2 * f
Where Voltage is in uV, frequency is in MHz.
As the following is the tested data on rk3399's big cluster.
frequency(MHz) Voltage(V) Current(mA) Dynamic-power-coefficient
24 0.8 15
48 0.8 23 ~417
96 0.8 40 ~443
216 0.8 82 ~438
312 0.8 115 ~430
408 0.8 150 ~455
So the dynamic-power-coefficient average value is about 436.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This allows basic support for SD highspeed cards but no UHS-I mode
got ready due to the propagated defer-probe error from RK805.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the core grf subnode for the io-domain controller.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Kill these two pinctrl reference totally from rk3399 as it
never work indeed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables the gpu and adds the mali-supply power for RK3399-GRU
devices.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add Mali GPU device tree node for the RK3399 SoCs, with devfreq
opp table.
RK3399 and RK3399-OP1 SoCs have a different recommendation table with
gpu opp. Also, the ARM's mali driver found on
https://developer.arm.com/products/software/mali-drivers/midgard-kernel.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
keep-power-in-suspend was invented for SDIO only, so it should
not be used for eMMC node.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We deprecated the "num-slots" property now and plan to get
rid of it finally. Just move a step to cleanup it from DT.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie_clkreqn actually doesn't work at all, so replace it with
pcie_clkreqn_cpm.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SdioAudio power domain includes the i2s/spdif/spi5/sdio.
So this patch adds the pd control for rk3399 i2s/spdif/spi5/sdio, in order
to save more power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip's RK3328 evaluation board has one usb2 otg controller
and one usb2 host controller which consist of EHCI and OHCI.
Each usb controller connects with one usb2 phy port through
UTMI+ interface. Let's enable them to support usb2 on RK3328
evaluation board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
[restructured enablement of u2phy subnodes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Provide the dynamic power coefficient of the big and little CPU
clusters. These numbers are currently in use on the Samsung Chromebook
Plus ("Kevin").
The power allocator thermal governor doesn't know how to do anything if
it doesn't get power parameters from its cooling devices (in this case,
CPUfreq). So this effectively enables the power-allocator governor.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[set the property in each core node]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Gru device tree currently contains entries for the regulators
ppvar_bigcpu, ppvar_litcpu, ppvar_gpu and ppvar_centerlogic; however,
the regulators have not been enabled, due to the lack of binding and driver
support for keeping the over-voltage protection (OVP) at bay and
preventing unintended regulator shutdowns on voltage downshifts.
Now, the vctrl regulator driver has been merged, along with new bindings
for asymmetric settling time. The driver is OVP aware, it splits larger
voltage decreases in multiple steps when necessary and adds required
delays.
This change renames each of the aforementioned regulators to
<orig_name>_pwm and adds a new vctrl regulator named <orig_name>.
The vctrl regulators use the voltage of their corresponding PWM regulator
as control voltage. The OVP related values are empirical and stem from
the Chrome OS kernel tree.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
[fixed node names and parent supplies of gpu and centerlogic]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Gru derivatives besides Kevin have slightly different voltage ranges for
their CPU regulators. Let's keep the base Gru file accurate and let
Kevin override.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
replace all occurrences of sdmcc with sdmmc in the arm64 rockchip
devicetree files.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
make usage of pci switches possible; some more qos and pinctrl nodes on
rk3399; updates for the rk3399 cpu operating points including separate
opps for the higher rates OP1 variant of the chip and mmc-nodes for
the rk3328.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlk5yQ4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgU7rCACdo8/RlAH58lR+35ZkJ3hAFHAlJJ9l2GFW
pobp2PYjtSCLaHz2o9yU7tT0peNph3YoeL9rFS44U/NUwtE4eloPbPea/FaGJ0nW
LUP6Y5bnM8sJMmO3YrG6Y3ryjTFD9GGe9IzSDgQhai+rXPfo/FZ+a1krpNN3HrJN
dd6PIozaa5aJpDkpET7NyvTRePMiDmuJAoj/9atDr8MLDKuuKNqQtnKcXGJ+3gUb
Zc4Ltxy2uTtc9bFi05Bi19AnZIqDXAGQdU+u+lqUGps3f8Q63iWYU/OEiCw3Oozs
3RJ7KXSZ58JN1CXwxMUE1OFplF5fVvPsv4Vzg8ddJ+vOK4E4t8Pd
=UMmB
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Support for the new rk3399 firefly board; extending the pcie ranges to
make usage of pci switches possible; some more qos and pinctrl nodes on
rk3399; updates for the rk3399 cpu operating points including separate
opps for the higher rates OP1 variant of the chip and mmc-nodes for
the rk3328.
* tag 'v4.13-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: update common rk3399 operating points
arm64: dts: rockchip: introduce rk3399-op1 operating points
arm64: dts: rockchip: enable usb3 controllers on rk3399-firefly
arm64: dts: rockchip: add ethernet0 alias on rk3399
arm64: dts: rockchip: bring rk3399-firefly power-tree in line
arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs
arm64: dts: rockchip: extent IORESOURCE_MEM_64 of PCIe for rk3399
arm64: dts: rockchip: extent bus-ranges of PCIe for rk3399
arm64: dts: rockchip: add pinctrl settings for some rk3399 peripherals
arm64: dts: rockchip: add some missing qos nodes on rk3399
arm64: dts: rockchip: add support for firefly-rk3399 board
dt-bindings: add firefly-rk3399 board support
Signed-off-by: Olof Johansson <olof@lixom.net>
The rk3399 has multiple variants with different frequency ratings.
The operating points currently in the kernel stem from the op1 variant
used in Gru ChromeOS devices and may not be suitable for general rk3399
chips. Therefore bring it back to the official general operating points.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The OP1 is a rk3399 variant used in ChromeOS devices with a slightly
higher frequency rating compared to the regular rk3399, but right now
the only available operating points don't match either variant
with both needing adjustments to actually fit their specs.
Therefore introduce separate operting points, from the ChromeOS kernel,
for the OP1 and use it on Gru devices.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The power-tree on the rk3399-firefly did not completely match the
documentation and vendor devicetree. It was also missing some
supply-hirarchy information and some regulator-gpio names did not
match the schematics. Fix this for the existing regulators before
introducing new things.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
