this patch add m45pe10 [1] chip support to the m25p80 driver.
[1] http://www.numonyx.com/Documents/Datasheets/M45PE10.pdf
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Extend erase timeout in M25P80 SPI Flash driver.
The M25P80 drivers fails erasing sectors on a M25P128 because the ready
wait timeout is too short. Change the timeout from a simple loop count to a
suitable number of seconds.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a logic error in "whole chip erase" for the m25p80 family. If
the whole device is successfully erased, erase_chip() will return 0, and
the code will fall through to the "else" clause, and do sector-by-sector
erase in addition to the whole-chip erase. This patch corrects that.
Also, the MAX_READY_WAIT_COUNT is insufficient for an m25p16 connected
to a 400 MHz powerpc. Increasing it allows me to successfully program
the device on my board.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Follow-on patch to the previous driver model patch for the MTD
framework. This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.
Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a
DaVinci-specific driver to the <linux/mtd/partitions.h> header.
Use those to eliminate #ifdefs in two drivers which had their own
definitions of mtd_has_partitions().
Quite a lot of other MTD drivers could benefit from using use one or both
of these to remove #ifdeffery. Maybe some Janitors would like to help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD has recently been upgraded for 64-bit support, see commit
number 69423d99fc in the
mtd-2.6.git tree (git://git.infradead.org/mtd-2.6.git)
or see this URL:
http://git.infradead.org/mtd-2.6.git?a=commit;h=69423d99fc182a81f3c5db3eb5c140acc6fc64be
Some variables in MTD data structures which were 32-bit
became 64-bit. Namely, the 'size' field in 'struct mtd_info'
and the 'addr'/'len' fields in 'struct erase_info'. This
means we have to use 'do_div' to divide them.
This patch fixes the following linking error:
ERROR: "__umoddi3" [drivers/mtd/devices/m25p80.ko] undefined!
This patch changes divisions of 64-bit variable so that they use
'do_div'. This patch also change some print placeholders to
get rid of gcc warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes broken terminology added in the "m25p80.c erase enhance" patch,
which added a chip erase command but called it "block erase". There are
already two block erase commands; blocks are 4KiB or 32KiB. There's also
a sector erase (usually 64 KiB). Chip erase typically covers Megabytes.
OPCODE_BE ==> OPCODE_CHIP_ERASE
erase_block ==> erase_chip
[dbrownell@users.sourceforge.net: update sector erase comments too ]
Signed-off-by: Chen Gong <clumsycg@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but seems to break on flashes
which don't have an extended id defined. If the table does not have an
extid defined, then we should ignore it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but in the process managed to
break detection of all flashes.
The ext jedec id check was inserted into an if statement that lacked
braces, and it did not add the required braces. As such, the detection
routine always returns the first entry in the SPI flash list.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This reverts commit 75d0ee2202.
Although it seems ObviouslyCorrect™, the spi_write() call uses DMA,
while spi_write_then_read() does not. Since our buffer is on the stack,
we must use the latter even though we don't actually want to read
anything back.
Pointed out by David Brownell <david-b@pacbell.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- add extended device information support
- add s25sl128 device support
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds an erase_block command to enhance erase operation
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Atmel serial flash tends to power up with the protection status bits set.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=4089
[michael.hennerich@analog.com: remove duplicate code]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Update chip ID tables in m25p80 to handle more SPI flash chips, matching
datasheets. All of these can use the same core operations and are newer
chips that support the JEDEC "read id" instruction:
- Atmel AT25 and AT26 (seven chips)
- Spansion S25SL (five chips)
- SST 25VF (four chips)
- ST M25, M45 (five more chips)
- Winbond W25X series (seven chips)
That JEDEC instruction is now used, either to support a sanity check on the
platform data holding board configuration data, or to determine chip type
when it's not included in platform data. In fact, boards that don't need a
standard partition table may not need that platform data any more.
For chips that support 4KiB erase units, use that smaller block size instead
of the larger size (usually 64KiB); it's less wasteful. (Tested on W25X80.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Convert semaphore usage in m25p80 driver to mutex; mention another kind of
SPI flash chip that should be able to use this driver (given minor tweaks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix build issues that show up with the m25p80 SPI flash driver when
building with MTD debug enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The flash_info structure has a bunch of missing fields which causes problems
when actually tryin to use some ST parts as it gets detected incorrectly.
Signed-off-by: Aubrey L1 <aubreylee@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Fix printk format warning:
drivers/mtd/devices/m25p80.c:189: warning: format '%zd' expects type
'signed size_t', but argument 6 has type 'u_int32_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/devices/m25p80.c: In function `m25p80_erase':
drivers/mtd/devices/m25p80.c:189: warning: signed size_t format, different type arg (arg 6)
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This collects some small SPI patches that seem to be missing from the MM tree:
- spi_butterfly kbuild hooks got dropped somehow; this restores them
- quick fix for a (theoretical?) m25p80_write() oops noted by Andrew
- quick fix for a potential config-specific oops for mtd_dataflash()
- minor doc tweaks
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.
From: David Brownell <dbrownell@users.sourceforge.net>
Updates including doc, bugfixes to the list code, add
spi_message_add_tail(). Plus, initialize things _before_ grabbing the
locks in some cases (in case it grows more expensive). This also merges
some bitbang updates of mine that didn't yet make it into the mm tree.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was originally a driver for the ST M25P80 SPI flash. It's been
updated slightly to handle other M25P series chips.
For many of these chips, the specific type could be probed, but for now
this just requires static setup with flash_platform_data that lists the
chip type (size, format) and any default partitioning to use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mike Lavender <mike@steroidmicros.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
