Aside from accelerated RFS, there is almost nothing that can be shared
between the filter table implementations for the Falcon architecture
and EF10.
Move the few shared functions into efx.c and rx.c and the rest into
farch.c. Introduce efx_nic_type operations for the implementation and
inline wrapper functions that call these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently efx_stop_datapath() will try to flush our DMA queues (if DMA
is enabled), then finalise software and hardware state for each queue.
However, for EF10 we must ask the MC to finalise each queue, which
implicitly starts flushing it, and then wait for the flush events.
We therefore need to delegate more of this to the NIC type.
Combine all the hardware operations into a new NIC-type operation
efx_nic_type::fini_dmaq, and call this before tearing down the
software state and buffers for all the DMA queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_process_channel_now() is unneeded since self-tests can rely on
normal NAPI polling. Remove it and all calls to it.
efx_channel::work_pending and efx_channel_processed() are also
unneeded (the latter being the same as efx_nic_eventq_read_ack()).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
PCI legacy interrupts are level-triggered, and we cannot mask them up
on an isolated device. Instead, disable the IRQ at the controller
until we have recovered.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Allocating 2 buffers per page is insanely inefficient when MTU is 1500
and PAGE_SIZE is 64K (as it usually is on POWER). Allocate as many as
we can fit, and choose the refill batch size at run-time so that we
still always use a whole page at once.
[bwh: Fix loop condition to allow for compound pages; rebase]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Enable RX DMA scattering iff an RX buffer large enough for the current
MTU will not fit into a single page and the NIC supports DMA
scattering for kernel-mode RX queues.
On Falcon and Siena, the RX_USR_BUF_SIZE field is used as the DMA
limit for both all RX queues with scatter enabled. Set it to 1824,
matching what Onload uses now.
Maintain a statistic for frames truncated due to lack of descriptors
(rx_nodesc_trunc). This is distinct from rx_frm_trunc which may be
incremented when scattering is disabled and implies an over-length
frame.
Whenever an MTU change causes scattering to be turned on or off,
update filters that point to the PF queues, but leave others
unchanged, as VF drivers assume scattering is off.
Add n_frags parameters to various functions, and make them iterate:
- efx_rx_packet()
- efx_recycle_rx_buffers()
- efx_rx_mk_skb()
- efx_rx_deliver()
Make efx_handle_rx_event() responsible for updating
efx_rx_queue::removed_count.
Change the RX pipeline state to a starting ring index and number of
fragments, and make __efx_rx_packet() responsible for clearing it.
Based on earlier versions by David Riddoch and Jon Cooper.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The pipeline mechanism will need to change a bit for scattered
packets. Add a wrapper to insulate efx_process_channel() from this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
[bwh: Remove more dead code, and make efx_ptp_rx() pull the data it
needs into the header area.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling. But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context. This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.
To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The assertion of netif_device_present() at the top of
efx_hard_start_xmit() may fail if we don't do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Allows an extra channel to override the standard receive_skb handler
and also for extra non generic operations to be performed on remove.
Also set default rx strategy so only skbs can be delivered to the
PTP receive function.
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently an skb requiring TSO may not fit within a minimum-size TX
queue. The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset). This issue is designated as CVE-2012-3412.
Set the maximum number of TSO segments for our devices to 100. This
should make no difference to behaviour unless the actual MSS is less
than about 700. Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.
To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Abstract some of the channel operations to allow for 'extra'
channels that do not have RX or TX queues.
- Try to assign a channel to each extra channel type that is enabled
for the NIC, but gracefully degrade if we can't allocate sufficient
MSI-X vectors
- Allow each extra channel type to generate its own channel name
- Allow channel types to disable reallocation and reinitialisation
of their channels
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Replace checksummed and discard booleans from efx_handle_rx_event()
with a bitmask, added to the flags field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Interrupts are normally generated by the event queues, moderated by
timers. However, they may also be triggered by detection of a 'fatal'
error condition (e.g. memory parity error) or by the host writing to
certain CSR fields as part of a self-test.
The IRQ level/index used for these on Falcon rev B0 and Siena is set
by the KER_INT_LEVE_SEL field and cached by the driver in
efx_nic::fatal_irq_level. Since this value is also relevant to
self-tests rename the field to just 'irq_level'.
Avoid unnecessary cache traffic by using a per-channel 'last_irq_cpu'
field and only writing to the per-controller field when the interrupt
matches efx_nic::irq_level. Remove the volatile qualifier and use
ACCESS_ONCE in the places we read these fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
These new functions will support an implementation of the ethtool
RX NFC rules API.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filter IDs are u32 (but never very large) so an ID/error return
value should have type s32.
Filter indices and search depths are never negative, so should
have type unsigned int.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC9020/SFL9021 device IDs are only used in the device ID table,
where we can just as well use comments.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reported TX IRQ moderation is generated in a completely crazy way.
Make it simple and correct.
When channels are shared between RX and TX, TX IRQ moderation must be
the same as RX IRQ moderation, but must be specified as 0! Allow it
to be either specified as the same, or left at its previous value
in which case it will be quietly overridden.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
