The following errors show up when booting the Nexus 5:
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_regulator_init: failed to init regulator, ret=-517
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_driver_probe: failed to init regulator
dsi_phy_regulator_init() already logs the error, so no need to log
the same error a second time in dsi_phy_driver_probe(). This patch
also changes dsi_phy_regulator_init() to not log the error if the
error code is -EPROBE_DEFER to reduce noise in dmesg.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[add some {}'s]
Signed-off-by: Rob Clark <robdclark@chromium.org>
For platforms that require the "zap shader" to take the GPU out of
secure mode at boot, we also need the zap fw to end up in the initrd.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add support for MDP5 version v3.0 found on msm8998.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
[silence unitialized variable warnings]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Unused and the extra rpm get/put interferes with handover from
bootloader (ie. happens before we have a chance to check if
things are already enabled).
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
If booting a device using EFI, efifb will likely come up and claim the
console. When the msm display stack finally comes up, we want the
console to move over to the msm fb, so add support to kick out any
firmware based framebuffers to accomplish the console transition.
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This switches the MSM HDMI code to use GPIO descriptors.
Normally we would fetch the GPIOs from the device with the
flags GPIOD_IN or GPIOD_OUT_[LOW|HIGH] to set up the lines
immediately, but since the code seems eager to actively
drive the lines high/low when turning HDMI on and off, we
just fetch the GPIOs as-is and keep the code explicitly
driving them.
The old code would try legacy bindings (GPIOs without any
"-gpios" suffix) but this has been moved to the gpiolib
as a quirk by the previous patch.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DPU has some kind of idea that it wants to be able to
bring up power using GPIO lines. The struct dss_gpio is however
completely unused and should this be done, it should be done
using the GPIO descriptor framework rather than this API
which relies on the global GPIO numberspace. Delete this
code before anyone hurt themselves.
The inclusion of <linux/gpio.h> was abused to get some OF
and IRQ headers implicitly included into the DPU utilities,
make these includes explicit and push them down into the actual
implementation.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This DSI driver uses the new descriptor API so these old
GPIO API includes are surplus.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This file is not using any symbols from <linux/gpio.h> so just
drop this include.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop the deprecated drmP.h header file, and trim msm_drv.h
to the relevant include files.
This resulted in a suprisingly many edits as many files relied
on headers included via msm_drv.h.
But msm_drv.h is not supposed to carry include files it do not need, so
the individual files have to include what extra they needs.
v2:
- Rebased on top of https://gitlab.freedesktop.org/drm/msm.git msm-next
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Bruce Wang <bzwang@chromium.org>
Cc: Shayenne Moura <shayenneluzmoura@gmail.com>
Cc: Mamta Shukla <mamtashukla555@gmail.com>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Carsten Behling <carsten.behling@googlemail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: Todor Tomov <todor.tomov@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190804065551.GA5211@ravnborg.org
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXVqvpwAKCRDj7w1vZxhR
xa3RAQDzAnt5zeesAxX4XhRJzHoCEwj2PJj9Re6xMJ9PlcfcvwD+OS+bcB6jfiXV
Ug9IBd/DqjlmD9G9MxFxfSV946rksAw=
=8uv4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixup dma_resv rename fallout]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190819141923.7l2adietcr2pioct@flea
Be more consistent with the naming of the other DMA-buf objects.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/323401/
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXUwPUAAKCRDj7w1vZxhR
xQ4lAQDK2ijx29YHeZspbOwP4Nwq95DFs1uQcSm5GvbRt1JSowD9EwkLeNfkPkel
Xv1Ts/Frgq7ckH2e2zkLPyCOFCHd0wA=
=rIUl
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-08-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
- HDCP: Add a Content protection type property
Cross-subsystem Changes:
Core Changes:
- Continue to rework the include dependencies
- fb: Remove the unused drm_gem_fbdev_fb_create function
- drm-dp-helper: Make the link rate calculation more tolerant to
non-explicitly defined, yet supported, rates
- fb-helper: Map DRM client buffer only when required, and instanciate a
shadow buffer when the device has a dirty function or says so
- connector: Add a helper to link the DDC adapter used by that connector to
the userspace
- vblank: Switch from DRM_WAIT_ON to wait_event_interruptible_timeout
- dma-buf: Fix a stack corruption
- ttm: Embed a drm_gem_object struct to make ttm_buffer_object a
superclass of GEM, and convert drivers to use it.
- hdcp: Improvements to report the content protection type to the
userspace
Driver Changes:
- Remove drm_gem_prime_import/export from being defined in the drivers
- Drop DRM_AUTH usage from drivers
- Continue to drop drmP.h
- Convert drivers to the connector ddc helper
- ingenic: Add support for more panel-related cases
- komeda: Support for dual-link
- lima: Reduce logging
- mpag200: Fix the cursor support
- panfrost: Export GPU features register to userspace through an ioctl
- pl111: Remove the CLD pads wiring support from the DT
- rockchip: Rework to use DRM PSR helpers, fix a bug in the VOP_WIN_GET
macro
- sun4i: Improve support for color encoding and range
- tinydrm: Rework SPI support, improve MIPI-DBI support, move to drm/tiny
- vkms: Rework of the CRC tracking
- bridges:
- sii902x: Add support for audio graph card
- tc358767: Rework AUX data handling code
- ti-sn65dsi86: Add Debugfs and proper DSI mode flags support
- panels
- Support for GiantPlus GPM940B0, Sharp LQ070Y3DG3B, Ortustech
COM37H3M, Novatek NT39016, Sharp LS020B1DD01D, Raydium RM67191,
Boe Himax8279d, Sharp LD-D5116Z01B
- Conversion of the device tree bindings to the YAML description
- jh057n00900: Rework the enable / disable path
- fbdev:
- ssd1307fb: Support more devices based on that controller
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808121423.xzpedzkpyecvsiy4@flea
The authentication can be circumvented, by design, by using the render
node.
From the driver POV there is no distinction between primary and render
nodes, thus we can drop the token.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: freedreno@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527081741.14235-7-emil.l.velikov@gmail.com
add_gpu_components() adds found GPU nodes from the DT to the match list,
regardless of the status of the nodes. This is a problem, because if the
nodes are disabled, they should not be on the match list because they will
not be matched. This prevents display from initing if a GPU node is
defined, but it's status is disabled.
Fix this by checking the node's status before adding it to the match list.
Fixes: dc3ea265b8 (drm/msm: Drop the gpu binding)
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626180015.45242-1-jeffrey.l.hugo@gmail.com
The mdp5 drm/kms driver currently does not work on command-mode DSI
panels due to 'vblank wait timed out' errors. This causes a latency
of seconds, or tens of seconds in some cases, before content is shown
on the panel. This hardware does not have the something that we can use
as a frame counter available when running in command mode, so we need to
fall back to using timestamps by setting the max_vblank_count to zero.
This can be done on a per-CRTC basis, so the convert mdp5 to use
drm_crtc_set_max_vblank_count().
This change was tested on a LG Nexus 5 (hammerhead) phone.
Suggested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190531094619.31704-3-masneyb@onstation.org
Since governor name is defined by DEVFREQ framework internally, use the
macro definition instead of using the name directly.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org> for the msm part.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725035239.1192-1-zbestahu@gmail.com
dpu encoder spinlock should be initialized during dpu encoder
init instead of dpu encoder setup which is part of modeset init.
Signed-off-by: Shubhashree Dhar <dhar@codeaurora.org>
[seanpaul resolved conflict in old init removal and revised the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1561357632-15361-1-git-send-email-dhar@codeaurora.org
Correct attempted NULL pointer dereference in context_init() when
running without an IOMMU.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Fixes: 295b22ae59 ("drm/msm: Pass the MMU domain index in struct msm_file_private")
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627020515.5660-1-masneyb@onstation.org
+ usual progress on cleanups
+ dsi vs EPROBE_DEFER fixes
+ msm8998 (snapdragon 835 support)
+ a540 gpu support (mesa support already landed)
+ dsi, dsi-phy support
+ mdp5 and dpu interconnect (bus/memory scaling) support
+ initial prep work for per-context pagetables (at least the parts that
don't have external dependencies like iommu/arm-smmu)
There is one more patch for fixing DSI cmd mode panels (part of a set of
patches to get things working on nexus5), but it would be conflicty with
1cff7440a8 in drm-next without rebasing or back-merge,
and since it doesn't conflict with anything in msm-next, I think it best
if Sean merges that through drm-mix-fixes instead.
(In other news, I've been making some progress w/ getting efifb working
properly on sdm850 laptop without horrible hacks, and drm/msm + clk stuff
not totally falling over when bootloader enables display and things are
already running when driver probes.. but not quite ready yet, hopefully
we can post some of that for 5.4.. should help for both the sdm835 and
sdm850 laptops.)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsj3N4XzDLSDoa+4RHZ9wXObYmhcep0M3LjnRg48BeLvg@mail.gmail.com
msm has switched over to drm_fb->obj[] a while ago already, so we can
just use the helper.
v2: Make it compile ... oops.
Cc: Eric Anholt <eric@anholt.net>
Cc: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Bruce Wang <bzwang@chromium.org>
Cc: Fritz Koenig <frkoenig@google.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190625204208.5614-3-daniel.vetter@ffwll.ch
The authentication can be circumvented, by design, by using the render
node.
From the driver POV there is no distinction between primary and render
nodes, thus we can drop the token.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: freedreno@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190527081741.14235-7-emil.l.velikov@gmail.com
Use drm_atomic_helper_dirtyfb() as the dirty callback in the
msm_framebuffer_funcs struct. Call drm_plane_enable_fb_damage_clips()
when the planes are initialized in mdp4, mdp5, and dpu1.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
These regs are write-only, and the hw throws a hissy-fit (ie. reboots)
when we try to read them for GPU state snapshot, in response to a GPU
hang. It is rather impolite when GPU recovery triggers an insta-
reboot, so lets remove the TPL1 registers from the snapshot.
Fixes: 7198e6b031 drm/msm: add a3xx gpu support
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
If bind fails, we can call msm_drm_uninit before kms elements have been
created. In this case, drm_atomic_helper_shutdown will fail since there
are no drm objects. Only call drm unregistration and shutdown if drm is
registered.
Also while we're in here move the workqueue destruction to below
component_unbind since components could be actively using the wq during
uninit or in their unbind routine.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190524202919.179289-1-sean@poorly.run
Now that the panel probe/setup is in the modeset path, we can call
dsi_manager_setup_encoder() in a common place for both internal and
external bridge setups.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-10-sean@poorly.run
Since deferred probe from the modeset init path now works, we can move
the panel initialization from detect() into connector init. This
avoids doing work in detect() and hopefully will result in a more
deterministic boot sequence between devices with a dsi panel, and those
with an external bridge.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-9-sean@poorly.run
It's a bit dangerous to store the flags in msm_dsi since there's no way to
tell when they're populated. Fortunately the only place that uses them
is the same place that fills them. So just use a local variable and
delete the struct member.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-5-sean@poorly.run
add_display_components() calls of_platform_populate, and we depopluate
on pdev remove, but not when probe fails. So if we get a probe deferral
in one of the components, we won't depopulate the platform. This causes
the core to keep references to devices which should be destroyed, which
causes issues when those same devices try to re-initialize on the next
probe attempt.
I think this is the reason we had issues with the gmu's device-managed
resources on deferral (worked around in commit 94e3a17f33a5).
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-3-sean@poorly.run
The 10nm pll driver didn't have any failure-path cleanup in register,
and the destroy function didn't unregister any of the hardware. This
patch adds both.
The reason things haven't been blowing up horribly is that msm_drv has a
reference count issue that keeps devices alive, so the destroy function
was never called. That will be fixed in a follow-up patch.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-1-sean@poorly.run
Fix the error paths in _dpu_kms_mmu_init() to properly
clean up the iommu domain and not call _dpu_kms_mmu_destroy() when
things are only partially setup.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617200405.131843-2-sean@poorly.run
The interconnect API provides an interface for consumer drivers to
express their bandwidth needs in the SoC. This data is aggregated
and the on-chip interconnect hardware is configured to the most
appropriate power/performance profile.
Use the API to configure the interconnects and request bandwidth
between DDR and the display hardware (MDP port(s) and rotator
downscaler).
v2: update the path names to be consistent with dpu, handle the NULL
path case, updated commit msg from Georgi.
v3: split out icc setup into it's own function, and rework logic
slightly so no interconnect paths is not fatal.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-By: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
dpu_mdss_destroy() can get called not just from
msm_drm_uninit() but also from msm_drm_bind() in case
of any failures.
dpu_mdss_destroy() removes the icc voting by calling
icc_put. This could accidentally remove the voting
done by pm_runtime_enable.
To make the voting balanced add a minimum vote in
dpu_mdss_init() to avoid any unclocked access.
This change depends on the following patch which
introduces interconnect binding to MDSS driver:
https://patchwork.codeaurora.org/patch/708155/
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The interconnect framework is designed to provide a
standard kernel interface to control the settings of
the interconnects on a SoC.
The interconnect API uses a consumer/provider-based model,
where the providers are the interconnect buses and the
consumers could be various drivers.
MDSS is one of the interconnect consumers which uses the
interconnect APIs to get the path between endpoints and
set its bandwidth requirement for the given interconnected
path.
Changes in v2:
- Remove error log and unnecessary check (Jordan Crouse)
Changes in v3:
- Code clean involving variable name change, removal
of extra paranthesis and variables (Matthias Kaehlcke)
Changes in v4:
- Add comments, spacings, tabs, proper port name
and icc macro (Georgi Djakov)
Changes in v5:
- Commit text and parenthesis alignment (Georgi Djakov)
Changes in v6:
- Change to new icc_set API's (Doug Anderson)
Changes in v7:
- Fixed a typo
Changes in v8:
- Handle the of_icc_get() returning NULL case. In practice
icc_set_bw() will gracefully handle the case of a NULL path,
but it's probably best for clarity to keep num_paths=0 in
this case.
Signed-off-by: Sravanthi Kollukuduru <skolluku@codeaurora.org>
Signed-off-by: Jayant Shekhar <jshekhar@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Sean Paul <sean@poorly.run>
