Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DIV_ROUND_CLOSEST() when dealing with the calibration values to make the
calculations less error prone.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Shunt resistance values greater than the chip's calibration factor make no
sense since the actual value written to the register equals:
<calibration factor> / <shunt>
Bail-out from ina2xx_probe() if the configured value is greater than the
calibration factor.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Chips from the ina family don't like to be uninitialized. In case the power
is cut-off and restored again the calibration register will be reset
to 0 and both the power and current registers will remain at 0.
Check the calibration register in ina2xx_update_device() and reinitialize
the chip if needed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use module_pci_driver to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
On many motherboards, for an unknown reason, the thermal sensor seems
to be disabled and will return a constant temperature value of 36.5
degrees Celsius. Don't bind to the device in that case, so that we
don't report this bogus value to userspace.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code a
bit.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.
Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
TMP435 supports a range of I2C addresses, not just 0x4c.
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A chip returning 0x00 in all registers is erroneously detected
as LM75. Check hysteresis and temperature limit registers and
abort if both are 0 to reduce the likelyhood for this to happen.
Reviewed-by: Rob Coulson <rob.coulson@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Poweroff the fans when shutting down the system. Else,
echo '1' > /sys/class/hwmon/hwmon0/fan1_target; poweroff leaves the
fan running if the System power off does not drive the gpio expander
which might control the fan power supply.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Certain I2C based GPIO expanders could be used in sleepable context,
this results in:
[ 115.890569] ------------[ cut here ]------------
[ 115.895422] WARNING: CPU: 0 PID: 1115 at drivers/gpio/gpiolib.c:1370 gpiod_set_raw_value+0x40/0x4c()
[ 115.905024] Modules linked in:
[ 115.908229] CPU: 0 PID: 1115 Comm: sh Tainted: G W 3.18.0-rc7-next-20141203-dirty #1
[ 115.917461] Hardware name: Generic DRA74X (Flattened Device Tree)
[ 115.923876] [<c0015368>] (unwind_backtrace) from [<c00119f4>] (show_stack+0x10/0x14)
[ 115.932013] [<c00119f4>] (show_stack) from [<c05b78e8>] (dump_stack+0x78/0x94)
[ 115.939594] [<c05b78e8>] (dump_stack) from [<c003de28>] (warn_slowpath_common+0x7c/0xb4)
[ 115.948094] [<c003de28>] (warn_slowpath_common) from [<c003de7c>] (warn_slowpath_null+0x1c/0x24)
[ 115.957315] [<c003de7c>] (warn_slowpath_null) from [<c03461e8>] (gpiod_set_raw_value+0x40/0x4c)
[ 115.966457] [<c03461e8>] (gpiod_set_raw_value) from [<c04866f4>] (set_fan_speed+0x4c/0x64)
[ 115.975145] [<c04866f4>] (set_fan_speed) from [<c04868a8>] (set_rpm+0x98/0xac)
[ 115.982742] [<c04868a8>] (set_rpm) from [<c039fb4c>] (dev_attr_store+0x18/0x24)
[ 115.990426] [<c039fb4c>] (dev_attr_store) from [<c01b0a28>] (sysfs_kf_write+0x4c/0x50)
[ 115.998742] [<c01b0a28>] (sysfs_kf_write) from [<c01afe1c>] (kernfs_fop_write+0xbc/0x19c)
[ 116.007333] [<c01afe1c>] (kernfs_fop_write) from [<c0148cc4>] (vfs_write+0xb0/0x1a0)
[ 116.015461] [<c0148cc4>] (vfs_write) from [<c0148fbc>] (SyS_write+0x44/0x84)
[ 116.022881] [<c0148fbc>] (SyS_write) from [<c000e5c0>] (ret_fast_syscall+0x0/0x48)
[ 116.030833] ---[ end trace 3a0b636123acab82 ]---
So, switch over to sleepable GPIO operations as there is no mandatory
need for non-sleepable gpio operations in the fan driver.
This allows the fan driver to be used with i2c based gpio expanders such
as palmas_gpio.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of i2c_smbus_read_byte_data() is checked in
tmp401_init_client(), but only a warning is printed and the device is
registered anyway. This leads to devices being registered even if they
cannot be physically detected.
Bail out from probe in case of write errors and notify the user.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95233 is similar to LM95234, but it only supports two
instead of four external temperature sensors.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM95235 is register compatible to LM95245.
Also update link to LM95245 data sheet, and drop the link to the
datasheet from the driver source to simplify code maintenance.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of i2c_smbus_write_word_swapped() isn't checked in
ina2xx_probe(). This leads to devices being registered even if they cannot
be physically detected (e.g. device is not powered-up at boot-time).
Even after restoring power to such device, it is left unconfigured as the
configuration has never been actually written to the register.
Error out in case of write errors in probe and notify the user.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[Guenter Roeck: Fixed multi-line comment style]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
checkpatch complains about
WARNING: Missing a blank line after declarations
Add missing blank lines. Also reorder variables length-wise where appropriate
if a function header is touched anyway.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6792D is similar to NCT6791D. Only beep control and temperature
monitoring registers are different.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is basically a faster lm75 with improved (11 bit) resolution.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current driver probe() function assumes the sensor device to be
always present and gets executed every time if the driver is loaded,
but the appropriate hardware could not be present.
So, move the platform device creation as part of platform init code
and use the 'id_table' to check if the device is present or not.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The iio subsystem supports humidity sensors, so it makes sense
to support it in the iio-hwmon bridge as well.
Cc: Jonathan Cameron <jic23@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add simple on/off regulator support for ltc2978 and
other pmbus parts supported by the ltc2978 driver.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for simple on/off control of each channel.
To add regulator support, the pmbus part driver needs to add
regulator_desc information and number of regulators to its
pmbus_driver_info struct.
regulator_desc can be declared using default macro for a
regulator (PMBUS_REGULATOR) that is in pmbus.h
The regulator_init_data can be initialized from either
platform data or the device tree.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Different drivers request API extensions in of-thermal. For this reason,
additional callbacks are required to fit the new drivers needs.
The current API implementation expects the registering sensor driver
to provide a get_temp and get_trend callbacks as function parameters.
As the amount of callbacks is growing, this patch changes the existing
implementation to use a .ops field to hold all the of thermal callbacks
to sensor drivers.
This patch also changes the existing of-thermal users to fit the new
API design. No functional change is introduced in this patch.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: lm-sensors@lm-sensors.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
g762_remove() needs to first call hwmon_device_unregister() and then
g762_of_clock_disable(). For that reason, it is not possible to
convert it to devm_hwmon_device_register_with_groups() and the
the non device managed version must be used.
This is correctly stated in commit message for 398e16db62 ("hwmon:
(g762) Convert to hwmon_device_register_with_groups") but the
associated changes do in fact introduce a call to the device managed
version of the function.
This patch fixes that typo by switching to the non devm_ version.
Fixes: 398e16db62 ("hwmon: (g762) Convert to hwmon_device_register_with_groups")
Cc: stable@vger.kernel.org (3.17+)
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
F3 device ID is wrongly included in fam15h_power_id_table
for F16h M30h. It should be F4 device ID. Fix this.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The state of a PWM output is not clearly defined after resume. Some PWM
drivers do not restore the duty cycle upon resume, thus it is necessary to
manually restore the correct value.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Because we build kernels with drivers built in for many platforms, it's
normal for the ibmpowernv driver to be loaded on systems that don't have
the appropriate hardware.
Currently the driver spams the log with:
ibmpowernv ibmpowernv.0: Opal node 'sensors' not found
ibmpowernv: Platfrom driver probe failed
But there is no error, this machine is not a powernv and doesn't have
the hardware. So change the sensors message to dev_dbg(), and only print
an error about the probe failing if it's not ENODEV.
Also fix the spelling of "Platfrom" and print the actual error value.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Include linux/err.h to get the definitions for IS_ERR() PTR_ERR() and
ERR_PTR() used in the driver.
This fixes compilation on powerpc targets.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drivers should not call pm_power_off directly; it is not guaranteed
to be non-NULL. Call kernel_power_off instead.
Cc: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To get more comprehensive and integrated thermal management, it adds ntc
thermistor to thermal framework as a thermal sensor. It's governed thermal
susbsystem only if it is described in DT node. Otherwise, it just notifies
temperature to userspace via sysfs as it used to be.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ATTRIBUTE_GROUPS macro and devm_hwmon_device_register_with_groups() to
simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups() to simplify the code
and reduce code size.
Cc: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
