It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.
Fixes: a2965f12fd ("r8169: remove rtl8169_set_speed_xmii")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Neil MacLeod <neil@nmacleod.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses the ndlp to get the local rport which is then used
to get the nvme transport remoteport pointer. There can be cases where a stale
remoteport pointer is obtained as synchronization isn't done through the
different dereferences.
Correct by using locks to synchronize the dereferences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk-mq does not support runtime pm, so disable blk-mq support for now.
Fixes: d5038a13ec ("scsi: core: switch to scsi-mq by default")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We met a kernel panic when enabling earlycon, which is due to the fixmap
address of earlycon is not statically setup.
Currently the static fixmap setup in head_64.S only covers 2M virtual
address space, while it actually could be in 4M space with different
kernel configurations, e.g. when VSYSCALL emulation is disabled.
So increase the static space to 4M for now by defining FIXMAP_PMD_NUM to 2,
and add a build time check to ensure that the fixmap is covered by the
initial static page tables.
Fixes: 1ad83c858c ("x86_64,vsyscall: Make vsyscall emulation configurable")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com> (Xen parts)
Cc: H Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180920025828.23699-1-feng.tang@intel.com
9092c71bb7 ("mm: use sc->priority for slab shrink targets") changed the
way that the target slab pressure is calculated and made it
priority-based:
delta = freeable >> priority;
delta *= 4;
do_div(delta, shrinker->seeks);
The problem is that on a default priority (which is 12) no pressure is
applied at all, if the number of potentially reclaimable objects is less
than 4096 (1<<12).
This causes the last objects on slab caches of no longer used cgroups to
(almost) never get reclaimed. It's obviously a waste of memory.
It can be especially painful, if these stale objects are holding a
reference to a dying cgroup. Slab LRU lists are reparented on memcg
offlining, but corresponding objects are still holding a reference to the
dying cgroup. If we don't scan these objects, the dying cgroup can't go
away. Most likely, the parent cgroup hasn't any directly charged objects,
only remaining objects from dying children cgroups. So it can easily hold
a reference to hundreds of dying cgroups.
If there are no big spikes in memory pressure, and new memory cgroups are
created and destroyed periodically, this causes the number of dying
cgroups grow steadily, causing a slow-ish and hard-to-detect memory
"leak". It's not a real leak, as the memory can be eventually reclaimed,
but it could not happen in a real life at all. I've seen hosts with a
steadily climbing number of dying cgroups, which doesn't show any signs of
a decline in months, despite the host is loaded with a production
workload.
It is an obvious waste of memory, and to prevent it, let's apply a minimal
pressure even on small shrinker lists. E.g. if there are freeable
objects, let's scan at least min(freeable, scan_batch) objects.
This fix significantly improves a chance of a dying cgroup to be
reclaimed, and together with some previous patches stops the steady growth
of the dying cgroups number on some of our hosts.
Link: http://lkml.kernel.org/r/20180905230759.12236-1-guro@fb.com
Fixes: 9092c71bb7 ("mm: use sc->priority for slab shrink targets")
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Rik van Riel <riel@surriel.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'm' kcore_list item could point to kclist_head, and it is incorrect to
look at m->addr / m->size in this case.
There is no choice but to run through the list of entries for every
address if we did not find any entry in the previous iteration
Reset 'm' to NULL in that case at Omar Sandoval's suggestion.
[akpm@linux-foundation.org: add comment]
Link: http://lkml.kernel.org/r/1536100702-28706-1-git-send-email-asmadeus@codewreck.org
Fixes: bf991c2231 ("proc/kcore: optimize multiple page reads")
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Omar Sandoval <osandov@osandov.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: James Morse <james.morse@arm.com>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the clone and fork syscalls return EAGAIN when the limit on the
number of pids /proc/sys/kernel/pid_max is exceeded.
Currently, when the pid_max limit is exceeded, the kernel will return
ENOSPC from the fork and clone syscalls. This is contrary to the
documented behaviour, which explicitly calls out the pid_max case as one
where EAGAIN should be returned. It also leads to really confusing error
messages in userspace programs which will complain about a lack of disk
space when they fail to create processes/threads for this reason.
This error is being returned because alloc_pid() uses the idr api to find
a new pid; when there are none available, idr_alloc_cyclic() returns
-ENOSPC, and this is being propagated back to userspace.
This behaviour has been broken before, and was explicitly fixed in
commit 35f71bc0a0 ("fork: report pid reservation failure properly"),
so I think -EAGAIN is definitely the right thing to return in this case.
The current behaviour change dates from commit 95846ecf9d ("pid:
replace pid bitmap implementation with IDR AIP") and was I believe
unintentional.
This patch has no impact on the case where allocating a pid fails because
the child reaper for the namespace is dead; that case will still return
-ENOMEM.
Link: http://lkml.kernel.org/r/20180903111016.46461-1-ktsanaktsidis@zendesk.com
Fixes: 95846ecf9d ("pid: replace pid bitmap implementation with IDR AIP")
Signed-off-by: KJ Tsanaktsidis <ktsanaktsidis@zendesk.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Gargi Sharma <gs051095@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave, Andy and Peter are de facto overseing the mm parts of X86. Add an
explicit maintainers entry.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reinette Chatre is doing great job on enabling pseudo-locking and other
features in RDT. Add her as co-maintainer for RDT.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/1537472228-221799-1-git-send-email-fenghua.yu@intel.com
This reverts commit 11a6fc3dc7.
UBIFS wants to assert that xattr operations are only issued on files
with positive link count. The said patch made this operations return
-ENOENT for unlinked files such that the asserts will no longer trigger.
This was wrong since xattr operations are perfectly fine on unlinked
files.
Instead the assertions need to be fixed/removed.
Cc: <stable@vger.kernel.org>
Fixes: 11a6fc3dc7 ("ubifs: xattr: Don't operate on deleted inodes")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Richard Weinberger <richard@nod.at>
The following sequence triggers
ubifs_assert(c, c->lst.taken_empty_lebs > 0);
at the end of ubifs_remount_fs():
mount -t ubifs /dev/ubi0_0 /mnt
echo 1 > /sys/kernel/debug/ubifs/ubi0_0/ro_error
umount /mnt
mount -t ubifs -o ro /dev/ubix_y /mnt
mount -o remount,ro /mnt
The resulting
UBIFS assert failed in ubifs_remount_fs at 1878 (pid 161)
is a false positive. In the case above c->lst.taken_empty_lebs has
never been changed from its initial zero value. This will only happen
when the deferred recovery is done.
Fix this by doing the assertion only when recovery has been done
already.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The requested device name can be NULL or an empty string.
Check for that and refuse to continue. UBIFS has to do this manually
since we cannot use mount_bdev(), which checks for this condition.
Fixes: 1e51764a3c ("UBIFS: add new flash file system")
Reported-by: syzbot+38bd0f7865e5c6379280@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.
However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.
So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.
The issue has existed since route exceptions introduction.
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Reported-by: ian.periam@dialogic.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header ocelot_dev_gmii.h is unused since the inclusion of the driver.
It is unused, lets just remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handlers of IOCTLs in kvm_arch_vcpu_ioctl() are expected to set
their return value in "r" local var and break out of switch block
when they encounter some error.
This is because vcpu_load() is called before the switch block which
have a proper cleanup of vcpu_put() afterwards.
However, KVM_{GET,SET}_NESTED_STATE IOCTLs handlers just return
immediately on error without performing above mentioned cleanup.
Thus, change these handlers to behave as expected.
Fixes: 8fcc4b5923 ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because CRAT_CU_FLAGS_IOMMU_PRESENT was not set in some BIOS crat, we
need to workaround this.
For future compatibility, we also overwrite the bit in capability according
to the value of needs_iommu_device.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CWSR fails on Raven if the control stack is MTYPE_UC, which is used
for regular GART mappings. As a workaround we map it using MTYPE_NC.
The MEC firmware expects the control stack at one page offset from the
start of the MQD so it is part of the MQD allocation on GFXv9. AMDGPU
added a memory allocation flag just for this purpose.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yong Zhao <yong.zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A wrong register bit was examinated for checking SDMA status so it reports
false failures. This typo only appears on gfx_v7. gfx_v8 checks the correct
bit.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory. The kernel pointer should not be copied to
user memory. The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field. This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.
Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there. As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.
Based on an initial patch by Brian Belleville.
CVE-2018-7755
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Broke up long line.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The generic netlink family is only initialized during module init,
so it should be __ro_after_init like all other generic netlink
families.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was introduced to mlxsw in commit 7b81953066 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd36 ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Further MC-awareness configuration
Petr says:
Due to an issue in Spectrum chips, when unicast traffic shares the same
queue as BUM traffic, and there is congestion, the BUM traffic is
admitted to the queue anyway, thus pushing out all UC traffic. In order
to give unicast traffic precedence over BUM traffic, multicast-aware
mode is now configured on all ports. Under MC-aware mode, egress TCs
8..15 are used for BUM traffic, which has its own dedicated pool.
This patch set improves the way that the MC pool and the higher-order
TCs are integrated into the system.
In patch #1, shaper at the higher TCs is configured to the same value
that it has by default. It's better to have the corresponding artifact
in the code explicitly.
The 8 following patches gradually extend the devlink handling in mlxsw
to support the extra TCs and the new MC pool.
Patch #2 changes the way that pools are indexed in mlxsw. Instead of
using (FW index, direction) tuple to identify the pool and the
associated cache, mlxsw now uses devlink index. This change is necessary
because the new pool 15 is not contiguously adjacent to the
currently-used pools 0..3, and because it's only relevant on egress.
Using devlink index relaxes the requirement for symmetry and adjacency
imposed by using FW indexing.
In patch #3, the assumption that number of ingress TCs matches that of
egress TCs is relaxed to allow exposition of egress TCs 8..15.
In patches #4, #5 and #6, support for infinite quotas is introduced.
Infinite quotas are reported as taking all the memory in the system, but
actually use a mechanism where the infinity is configured explicitly.
In patches #7 and #8, support for configuring static pool sizes in
introduced. Statically-sized pools have been supported for a while now,
but during initialization, all pools have dynamic size. The patches
allow there to be a mix of by-default static and dynamic pools.
In patches #9 and #10, pool 15 resp. per-priority MC quotas are
explicitly configured to be in sync with the current recommendation for
handling BUM traffic in Spectrum chips.
In the following 3 patches, an mlxsw-specific selftest is added to test
the MC-awareness configuration.
First in patches #11 and #12, lib.sh is extended with functions to
collect ethtool stats, and to manage port MTU.
Then in patch #13 the selftest itself is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A so-called "MC-aware" mode has recently been enabled in mlxsw. In
MC-aware mode, BUM traffic is handled in a special way so that when a
switch is flooded with BUM, UC performance isn't unduly impacted.
Without enablement of this mode, a stream of BUM traffic can cause
sustained UC throughput drop in excess of 99 %.
Add a test for this behavior. Compare how much UC throughput degrades as
a stream of broadcast frames floods the switch. A minimal degradation is
tolerated to cover for glitches in traffic injection performance.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some selftests need to tweak MTU of an interface, and naturally should
at teardown restore the MTU back to the original value. Add two
functions to facilitate this MTU handling: mtu_set() to change MTU
value, and mtu_reset() to change it back to what it was before.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new service function to obtain ethtool counters.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBMM register configures shared buffer allocation and settings for
MC packets according to switch priority. The recommended values are no
reserved buffer and alpha of 1/4, which corresponds to buf_max of 6.
Update mlxsw_sp_sb_mms accordingly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pool 15 (indexed as 8) is dedicated to MC traffic. Its configuration has
been kept at default, because the table-based configuration wasn't
expressive enough to allow the explicit configuration.
Now that the configuration of pool 15 can be described, do so. The MC
pool should have infinite size, infinite per-TC quota, and per-port
limit of 90K.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some pools configured through the sb_pm entries may have by default
static size. The MC pool is now not explicitly configured, however it
gets configured as static implicitly by 0-initializing sb->prs, and a
follow-up patch adds an explicit configuration to the same effect.
To support this, pass max_buff taken from sb_pm and sb_cm entries
through cell conversion before handing it to mlxsw_sp_sb_pm_write(), if
the pool that the sb_pm entry configures is statically-sized.
To keep current behavior, update mlxsw_sp_sb_cms_egress[] to denote
buffer sizes in bytes (assuming Spectrum 1 cell sizes, which the
original code assumed as well) instead of cells. Note that a follow-up
patch changes this to infinite size.
Also tweak a comment at SBMM configuration to remain true now that
statically-sized pools exist.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBPM register configures the shared buffer allocation and
configuration per port and pool. The min_buff value is the buffer size
dedicated to this single function, and is configured in cells.
Currently, all sb_pm entries have 0 for min_buff, and therefore the
actual unit is immaterial. However, in a follow-up patch we want to add
entries with non-zero minimum.
Therefore pass the min_buff from the sb_pm table through the cell
conversion before handing it over to mlxsw_sp_sb_pm_write().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBCM register configures the shared buffer configuration according
to port and TC. So far all pools have had a dynamic size, where the
infinite size is easy to express by using max_buff of 0xff. However the
MC pool should be configured with static size, and the infinite size
thus needs to be set using the field SBCM.infi_max.
Therefore add the field infi_max to the SBCM register and to
mlxsw_reg_sbcm_pack(). Extend mlxsw_sp_sb_cm_write() to handle infinite
sizes as well. Report infinite pool limits as if the limit actually were
the total shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC pool should have an infinite size (i.e. no quota).
To that end, add infi_size to the SBPR register and extend
mlxsw_reg_sbpr_pack(). Also add MLXSW_SP_SB_INFI to denote
buffers that should have an infinite size.
Change mlxsw_sp_sb_pr_write() to take as parameter byte size,
instead of cell size, and add the special handling of infinite
buffers. Report pools with infinite size as if they actually
take the full shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Entities of infinite size will be reported as if they had the maximum
size allowed by the chip. To that end, keep track of maximum shared
buffer size in mlxsw_sp->sb.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code assumes that ingress and egress has the same number of
traffic classes. Since the introduction of MC-aware mode that assumption
hasn't held anymore, and there have been 16 TCs on the egress as opposed
to 8 on ingress.
Break the assumption of symmetry by splitting the artifacts related to
shared-buffer TC counting to ingress and egress parts.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw assumes that each ingress pool has its egress
counterpart, and that pool index for purposes of caching matches the
index with which the hardware should be configured. As we want to expose
the MC pool, both of these assumptions break.
Instead, maintain the pool index as long as possible. Unify ingress and
egress caches and use the pool index as cache index as well. Only
translate to FW pool numbering when actually packing the registers. This
simplifies things considerably, as the pool index is the only quantity
necessary to uniquely identify a pool, and the pool/direction split is
not necessary until firmware is talked to.
To support the mapping between pool indices and pool numbers and
directions, which is not neatly mathematical anymore, introduce a pool
descriptor table, indexed by pool index, to facilitate the translation.
Include the MC pool in the descriptor table as well, so that it can be
referenced from mlxsw_sp_sb_cms_egress.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.
By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hen we're comparing the hardware completion mask passed in from the
driver with the internal tag pending mask, we need to account for the
fact that the internal tag is different from the hardware tag. If not,
then we can end up either prematurely completing the internal tag (since
it's not set in the hw mask), or simply flag an error:
ata2: illegal qc_active transition (100000000->00000001)
If the internal tag is set, then swap that with the hardware tag in this
case before comparing with what the hardware reports.
Fixes: 28361c4036 ("libata: add extra internal command")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201151
Cc: stable@vger.kernel.org
Reported-by: Paul Sbarra <sbarra.paul@gmail.com>
Tested-by: Paul Sbarra <sbarra.paul@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The naked attribute is supported by at least gcc >= 4.6 (for ARM,
which is the only current user), gcc >= 8 (for x86), clang >= 3.1
and icc >= 13. See https://godbolt.org/z/350Dyc
Therefore, move it out of compiler-gcc.h so that the definition
is shared by all compilers.
This also fixes Clang support for ARM32 --- 815f0ddb34
("include/linux/compiler*.h: make compiler-*.h mutually exclusive").
Fixes: 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Eli Friedman <efriedma@codeaurora.org>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-sparse@vger.kernel.org
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9c695203a7 ("compiler-gcc.h: gcc-4.5 needs noclone
and noinline on __naked functions") added noinline and noclone
as a workaround for a gcc 4.5 bug, which was resolved in 4.6.0.
Since now the minimum gcc supported version is 4.6,
we can clean it up.
See https://gcc.gnu.org/bugzilla/show_bug.cgi?id=44290
and https://godbolt.org/z/h6NMIL
Fixes: 815f0ddb34 ("include/linux/compiler*.h: make compiler-*.h mutually exclusive")
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Eli Friedman <efriedma@codeaurora.org>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-sparse@vger.kernel.org
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6 ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions typec_mux_get() and typec_switch_get() already
make sure that the mux device reference count is
incremented, but the same must be done to the driver module
as well to prevent the drivers from being unloaded in the
middle of operation.
This fixes a potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: 93dd2112c7 ("usb: typec: mux: Get the mux identifier from function parameter")
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applying dynamic usbcore quirks in early booting when the slab is
not yet ready would cause kernel panic of null pointer dereference
because the quirk_count has been counted as 1 while the quirk_list
was failed to allocate.
i.e.,
[ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
[ 1.045016] PGD 0
[ 1.045026] Oops: 0000 [#1] PREEMPT SMP
[ 1.046986] gsmi: Log Shutdown Reason 0x03
[ 1.046995] Modules linked in:
[ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28
[ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017
[ 1.047028] Workqueue: usb_hub_wq hub_event
[ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000
[ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
To tackle this odd, let's balance the quirk_count to 0 when the kcalloc
call fails, and defer the quirk setting into a lower level callback
which ensures that the kernel memory management has been initialized.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
