On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts 5829210483 ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 5829210483 ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes: edacb098ea ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry_from_reverse() iterates backwards over the list from
the current position, but in the error path we should start from the
previous position.
Fix this by using list_for_each_entry_continue_reverse() instead.
This suppresses the following error from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//spectrum_mr.c:655:34-38: ERROR:
invalid reference to the index variable of the iterator on line 636
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qlcnic_83xx_get_reset_instruction_template, the variable
of null test is bad, so correct it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
00:05.0 Ethernet controller [0200]: Amazon.com, Inc. Elastic Network
Adapter (ENA) [1d0f:ec20]
Suggested-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl56fu0ACgkQSD+KveBX
+j4g1Qf/edWPTCMGK4eb0jBPUvnxkoGPYj4cq0tfeUaY7Q4r95RzNjuW3gTotzGV
JZymoC2OoWQxUR2Ye0FkM1C/RQFIAHinEX/KFOMJ6PL+k4+micXeIGNfVo3aflO0
kaTcBdgZKqFS5hpRtWZc/DVRWckqJYtaAJEFliQbYGwmfiZNoNr0/ZeU+/DX2dHn
bQkRHQZ3Zq43P4FhVBSyrfmsxUI71k7GtCdJ5G4i80e8qCCARKZDx7q1FRC0k6fh
a84+7NxpFRkl+kT+se/bxcQaFht49YSJVauGMKK8Ae+pz0XEaNrYsFz9zQY/s7W6
4a62hzlHuVmUwteZfH+secZzCnOkUw==
=rO1d
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-24
This series introduces some fixes to mlx5 driver.
From Aya, Fixes to the RX error recovery flows
From Leon, Fix IB capability mask
Please pull and let me know if there is any problem.
For -stable v5.5
('net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure')
For -stable v5.4
('net/mlx5e: Fix ICOSQ recovery flow with Striding RQ')
('net/mlx5e: Do not recover from a non-fatal syndrome')
('net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset')
('net/mlx5e: Enhance ICOSQ WQE info fields')
The above patch ('net/mlx5e: Enhance ICOSQ WQE info fields')
will fail to apply cleanly on v5.4 due to a trivial contextual conflict,
but it is an important fix, do I need to do something about it or just
assume Greg will know how to handle this ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
[0] https://bugzilla.redhat.com/show_bug.cgi?id=1792839
Fixes: 003bd5b4a7 ("r8169: don't use MSI before RTL8168d")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4_ptp_fineadjtime() doesn't pass the signedness of offset delta
in FW_PTP_CMD. Fix it by passing correct sign.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-fatal syndromes like LOCAL_LENGTH_ERR, recovery shouldn't be
triggered. In these scenarios, the RQ is not actually in ERR state.
This misleads the recovery flow which assumes that the RQ is really in
error state and no more completions arrive, causing crashes on bad page
state.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cap_mask1 isn't protected by field_select and not listed among RW
fields, but it is required to be written to properly initialize ports
in IB virtualization mode.
Link: https://lore.kernel.org/linux-rdma/88bab94d2fd72f3145835b4518bc63dda587add6.camel@redhat.com
Fixes: ab118da4c1 ("net/mlx5: Don't write read-only fields in MODIFY_HCA_VPORT_CONTEXT command")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed7903 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl5hh6wACgkQSD+KveBX
+j6qvQf9HQsiQ+cE1UIbM/IzyTWXeBMzjljCWFgQfvyKQjSFnoATeVl6GMQJNk7M
ovQ7XHOlN36E/tQW/ypnwbX+btjl/mDEJsxEcvVf4gnw/QH1AwUjo291vPfrE5md
DcWWe9Jrq2MkHeZAgIt/Tnw4GYIwQOBVmYgky3A0+azzuvxK+nXX6JJG5JqRR8Wd
tBsN9UKok1nOt73d+TyHjGnzQHWzGBdS0vlxl0MYcD1QD66UzA0Atgz5aUQLGvTK
Nk/IcHr3SF+0kvbtpjRxlrpi4ywD2gBNHXMJX1DDnCkqg9nWjJ5DByYDASo+I6uL
0fMNsimp/gZG8HD0oFEVTFgaqPACUA==
=DEqe
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v5.4
('net/mlx5: DR, Fix postsend actions write length')
For -stable v5.5
('net/mlx5e: kTLS, Fix TCP seq off-by-1 issue in TX resync flow')
('net/mlx5e: Fix endianness handling in pedit mask')
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware offloading of the NETIF_F_HW_CSUM and NETIF_F_RXCSUM
features requires the use of Transmit Status Blocks before transmit
frame data and Receive Status Blocks before receive frame data to
carry the checksum information.
Unfortunately, these status blocks are currently only enabled when
the NETIF_F_HW_CSUM feature is enabled. As a result NETIF_F_RXCSUM
will not actually be offloaded to the hardware unless both it and
NETIF_F_HW_CSUM are enabled. Fortunately, that is the default
configuration.
This commit addresses this issue by always enabling the use of
status blocks on both transmit and receive frames. Further, it
replaces the use of a dedicated flag within the driver private
data structure with direct use of the netdev features flags.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we clean up devicetree related configuration
also when clock init fails.
Fixes: fecd4d7eef ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Headers ionic_if.h and ionic_regs.h are licensed under three alternative
licenses and the used SPDX-License-Identifier expression makes
./scripts/spdxcheck.py complain:
drivers/net/ethernet/pensando/ionic/ionic_if.h: 1:52 Syntax error: OR
drivers/net/ethernet/pensando/ionic/ionic_regs.h: 1:52 Syntax error: OR
As OR is associative, it is irrelevant if the parentheses are put around
the first or the second OR-expression.
Simply add parentheses to make spdxcheck.py happy.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
the minimum value of skb len that hw supports is 32 rather than 17
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the second input parameter of wait_for_completion_timeout should
be jiffies instead of millisecond
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add read barrier in driver code to keep from reading other fileds
in dma memory which is writable for hw until we have verified the
memory is valid for driver
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
should disable eq irq before freeing it, must clear event queue
depth in hw before freeing relevant memory to avoid illegal
memory access and update consumer idx to avoid invalid interrupt
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it's unreliable for fw to check whether IO is stopped, so driver
wait for enough time to ensure IO process is done in hw before
freeing resources
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit d429005fdf ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization the driver issues a software reset command and
then waits for the system status to change back to "ready" state.
However, before issuing the reset command the driver does not check that
the system is actually in "ready" state. On Spectrum-{1,2} systems this
was always the case as the hardware initialization time is very short.
On Spectrum-3 systems this is no longer the case. This results in the
software reset command timing-out and the driver failing to load:
[ 6.347591] mlxsw_spectrum3 0000:06:00.0: Cmd exec timed-out (opcode=40(ACCESS_REG),opcode_mod=0,in_mod=0)
[ 6.358382] mlxsw_spectrum3 0000:06:00.0: Reg cmd access failed (reg_id=9023(mrsr),type=write)
[ 6.368028] mlxsw_spectrum3 0000:06:00.0: cannot register bus device
[ 6.375274] mlxsw_spectrum3: probe of 0000:06:00.0 failed with error -110
Fix this by waiting for the system to become ready both before issuing
the reset command and afterwards. In case of failure, print the last
system status to aid in debugging.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
last_keep_alive_jiffies is updated in probe and when a keep-alive
event is received. In case the driver times-out on a keep-alive event,
it has high chances of continuously timing-out on keep-alive events.
This is because when the driver recovers from the keep-alive-timeout reset
the value of last_keep_alive_jiffies is very old, and if a keep-alive
event is not received before the next timer expires, the value of
last_keep_alive_jiffies will cause another keep-alive-timeout reset
and so forth in a loop.
Solution:
Update last_keep_alive_jiffies whenever the device is restored after
reset.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx req_id is an index in struct ena_eth_io_rx_cdesc_base.
The driver should validate that the Rx req_id it received from
the device is in range [0, ring_size -1]. Failure to do so could
yield to potential memory access violoation.
The validation was mistakenly done when refilling
the Rx submission queue and not in Rx completion queue.
Fixes: ad974baef2 ("net: ena: add support for out of order rx buffers refill")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug:
In short the main issue is caused by the fact that the number of queues
is changed using ethtool after ena_probe() has been called and before
ena_up() was executed. Here is the full scenario in detail:
* ena_probe() is called when the driver is loaded, the driver is not up
yet at the end of ena_probe().
* The number of queues is changed -> io_queue_count is changed as well -
ena_up() is not called since the "dev_was_up" boolean in
ena_update_queue_count() is false.
* ena_up() is called by the kernel (it's called asynchronously some
time after ena_probe()). ena_setup_io_intr() is called by ena_up() and
it uses io_queue_count to get the suitable irq lines for each msix
vector. The function ena_request_io_irq() is called right after that
and it uses msix_vecs - This value only changes during ena_probe() and
ena_restore() - to request the irq vectors. This results in "Failed to
request I/O IRQ" error for i > io_queue_count.
Numeric example:
* After ena_probe() io_queue_count = 8, msix_vecs = 9.
* The number of queues changes to 4 -> io_queue_count = 4, msix_vecs = 9.
* ena_up() is executed for the first time:
** ena_setup_io_intr() inits the vectors only up to io_queue_count.
** ena_request_io_irq() calls request_irq() and fails for i = 5.
How to reproduce:
simply run the following commands:
sudo rmmod ena && sudo insmod ena.ko;
sudo ethtool -L eth1 combined 3;
Fix:
Use ENA_MAX_MSIX_VEC(adapter->num_io_queues + adapter->xdp_num_queues)
instead of adapter->msix_vecs. We need to take XDP queues into
consideration as they need to have msix vectors assigned to them as well.
Note that the XDP cannot be attached before the driver is up and running
but in XDP mode the issue might occur when the number of queues changes
right after a reset trigger.
The ENA_MAX_MSIX_VEC simply adds one to the argument since the first msix
vector is reserved for management queue.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overview:
We don't frequently change the msix vectors throughout the life cycle of
the driver. We do so in two functions: ena_probe() and ena_restore().
ena_probe() is only called when the driver is loaded. ena_restore() on the
other hand is called during device reset / resume operations.
We use num_io_queues for calculating and allocating the number of msix
vectors. At ena_probe() this value is equal to max_num_io_queues and thus
this is not an issue, however ena_restore() might be called after the
number of io queues has changed.
A possible bug scenario is as follows:
* Change number of queues from 8 to 4.
(num_io_queues = 4, max_num_io_queues = 8, msix_vecs = 9,)
* Trigger reset occurs -> ena_restore is called.
(num_io_queues = 4, max_num_io_queues =8 , msix_vecs = 5)
* Change number of queues from 4 to 6.
(num_io_queues = 6, max_num_io_queues = 8, msix_vecs = 5)
* The driver will reset due to failure of check_for_rx_interrupt_queue()
Fix:
This can be easily fixed by always using max_num_io_queues to init the
msix_vecs, since this number won't change as opposed to num_io_queues.
Fixes: 4d19266022 ("net: ena: multiple queue creation related cleanups")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked at least 5
cycles while the sw_reset is asserted to ensure a clean reset.
That commit enabled local loopback to provide an Rx clock from the
GENET sourced Tx clk. However, when connected in MII mode the Tx
clk is sourced by the PHY so if an EPHY is not supplying clocks
(e.g. when the link is down) the UniMAC does not receive the
necessary clocks.
This commit extends the sw_reset window until the PHY reports that
the link is up thereby ensuring that the clocks are being provided
to the MAC to produce a clean reset.
One consequence is that if the system attempts to enter a Wake on
LAN suspend state when the PHY link has not been active the MAC
may not have had a chance to initialize cleanly. In this case, we
remove the sw_reset and enable the WoL reception path as normal
with the hope that the PHY will provide the necessary clocks to
drive the WoL blocks if the link becomes active after the system
has entered suspend.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a55402c93.
This is not a good solution when connecting to an external switch
that may not support the isolation of the TXC signal resulting in
output driver contention on the pin.
A different solution is necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1f550dc44.
platform_get_irq_optional() will still return -ENXIO when no interrupt
is provided so the additional error handling caused the driver prone to
fail when no interrupt was specified. Revert the change so we can apply
the correct minimal fix.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat all internal delay variants the same as RGMII.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit set a value of 2^31-1 in order to "disable" the shaper
on a given a port. However, the length of the maximum shaper rate field
was not updated from 28 bits to 31 bits, which means ports are still
limited to ~268Gbps despite supporting speeds of 400Gbps.
Fix this by increasing the field's length.
Fixes: 92afbfedb7 ("mlxsw: reg: Increase MLXSW_REG_QEEC_MAS_DIS")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c219399988 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in remove filters entry
failure for cxgb4 unload path. This patch fix that.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bounds check on index is off by one and can lead to
an out of bounds access on array priv->filters_loc when index is
RXCHK_BRCM_TAG_MAX.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177 ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
