HT TDLS traffic should be protected in a non-HT BSS to avoid
collisions. Therefore, when TDLS peers join/leave, check if
protection is (now) needed and set the ht_operation_mode of
the virtual interface according to the HT capabilities of the
TDLS peer(s).
This works because a non-HT BSS connection never sets (or
otherwise uses) the ht_operation_mode; it just means that
drivers must be aware that this field applies to all HT
traffic for this virtual interface, not just the traffic
within the BSS. Document that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlwifi driver was the only driver that used this, but as
it turns out it never needed it, so we can remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may need to store data per key, for example for PN
validation. Allow this by adding a pointer to the struct that
the driver can assign.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow a device to specify support for the TDLS wider-bandwidth feature.
Indicate this support during TDLS setup in the ext-capab IE and set an
appropriate station flag when our TDLS peer supports it.
This feature gives TDLS peers the ability to use a wider channel than
the base width of the BSS. For instance VHT capable TDLS peers connected
on a 20MHz channel can extend the channel to 80MHz, if regulatory
considerations allow it.
Do not cap the bandwidth of such stations by the current BSS channel width
in mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are multiple RX queues, the PN checks in mac80211 cannot be
used since packets might be processed out of order on different CPUs.
Allow the driver to report that the PN has been checked, drivers that
will use multi-queue RX will have to set this flag.
For now, the flag is only valid when the frame has been decrypted, in
theory that restriction doesn't have to be there, but in practice the
hardware will have decrypted the frame already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As there's no driver using this capability and reporting zero-length
A-MPDU subframes for radiotap monitoring, remove the capability to
free up two RX flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FIF_PROMISC_IN_BSS was removed in commit df1404650c
("mac80211: remove support for IFF_PROMISC").
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the pointers are really only accessible to root and used
pretty much only by wpa_supplicant, this is still not great; even
for debugging it'd be easier to have something that's easier to
read and guaranteed to never get reused.
With the recent change to make mac80211 create an ack_skb for the
mgmt-tx path this becomes possible, only the client probe method
needs to also allocate an ack_skb, and we can store the cookie in
that skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers supporting TSO or similar features, but that still have
PN assignment in software, there's a need to have some memory to
store the current PN value. As mac80211 already stores this and it's
somewhat complicated to add a per-driver area to the key struct (due
to the dynamic sizing thereof) it makes sense to just move the TX PN
to the keyconf, i.e. the public part of the key struct.
As TKIP is more complicated and we won't able to offload it in this
way right now (fast-xmit is skipped for TKIP unless the HW does it
all, and our hardware needs MMIC calculation in software) I've not
moved that for now - it's possible but requires exposing a lot of
the internal TKIP state.
As an bonus side effect, we can remove a lot of code by assuming the
keyseq struct has a certain layout - with BUILD_BUG_ON to verify it.
This might also improve performance, since now TX and RX no longer
share a cacheline.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The kernel-doc description for the drv_priv member of
struct ieee80211_txq was missing, leading to errors.
Add a suitable description to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is just a code cleanup, make the LED trigger names const
as they're not expected to be modified by drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When frames time out in the reordering buffer, it is a
good indication that something went wrong and the driver
may want to know about that to take action or trigger
debug flows.
It is pointless to notify the driver about each frame that
is released. Notify each time the timer fires.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we receive a BAR, this typically means that our peer
doesn't hear our Block-Acks or that we can't hear its
frames. Either way, it is a good indication that the link
is in a bad condition. This is why it can serve as a probe
to the driver.
Use the event_callback callback for this.
Since more events with the same data will be added in the
feature, the structure that describes the data attached to
the event is called in a generic name: ieee80211_ba_event.
This also means that from now on, the event_callback can't
sleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drivers want to support S/G (really just gather DMA on TX) then
we can now easily support this on the fast-xmit path since it just
needs to write to the ethernet header (and already has a check for
that being possible.)
However, disallow this on the regular TX path (which has to handle
fragmentation, software crypto, etc.) by calling skb_linearize().
Also allow the related HIGHDMA since that's not interesting to the
code in mac80211 at all anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to speed up mac80211's TX path, add the "fast-xmit" cache
that will cache the data frame 802.11 header and other data to be
able to build the frame more quickly. This cache is rebuilt when
external triggers imply changes, but a lot of the checks done per
packet today are simplified away to the check for the cache.
There's also a more detailed description in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A couple of enums in mac80211.h became structures recently, but the
comments didn't follow suit, leading to errors like:
Error(.//include/net/mac80211.h:367): Cannot parse enum!
Documentation/DocBook/Makefile:93: recipe for target 'Documentation/DocBook/80211.xml' failed
make[1]: *** [Documentation/DocBook/80211.xml] Error 1
Makefile:1361: recipe for target 'mandocs' failed
make: *** [mandocs] Error 2
Fix the comments comments accordingly. Added a couple of other small
comment fixes while I was there to silence other recently-added docbook
warnings.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the reason
of the deauth.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the authentication.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow mac80211 drivers to call cfg80211 APIs with
the right handle.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some device drivers offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
[fix commit log, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes the driver might want to modify private data in interfaces
that are down. One possible use-case is cleaning up interface state
after HW recovery. Some interfaces that were up before the recovery took
place might be down now, but they might still be "dirty".
Introduce a new iterate_interfaces() API and a new ACTIVE iterator flag.
This way the internal implementation of the both active and inactive
APIs remains the same.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon's timestamp, device system time associated with this beacon and
DTIM count parameters are not updated in the associated vif context
if the latest beacon's content is identical to the previously received.
It make sense to update these changing parameters on every beacon so the
driver can get most updated values. This may be necessary, for example,
to avoid either beacons' drift effect or device time stamp overrun.
IMPORTANT: Three sync_* parameters - sync_ts, sync_device_ts and
sync_dtim_count would possibly be out of sync by the time the driver will
use them. The synchronized view is currently guaranteed only in certain
callbacks.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure BIP-GMAC-128 and BIP-GMAC-256 to the
driver and also use software-implementation within mac80211 when the
driver does not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure GCMP and GCMP-256 to the driver and
also use software-implementation within mac80211 when the driver does
not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[remove a spurious newline]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Control per packet Transmit Power Control (TPC) in lower drivers
according to TX power settings configured by the user. In particular TPC is
enabled if value passed in enum nl80211_tx_power_setting is
NL80211_TX_POWER_LIMITED (allow using less than specified from userspace),
whereas TPC is disabled if nl80211_tx_power_setting is set to
NL80211_TX_POWER_FIXED (use value configured from userspace)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers unfortunately cannot support software crypto, but
mac80211 currently assumes that they do.
This has the issue that if the hardware enabling fails for some
reason, the software fallback is used, which won't work. This
clearly isn't desirable, the error should be reported and the
key setting refused.
Support this in mac80211 by allowing drivers to set a new HW
flag IEEE80211_HW_SW_CRYPTO_CONTROL, in which case mac80211 will
only allow software fallback if the set_key() method returns 1.
The driver will also need to advertise supported cipher suites
so that mac80211 doesn't advertise any (future) software ciphers
that the driver can't actually do.
While at it, to make it easier to support this, refactor the
ieee80211_init_cipher_suites() code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are treated the same as 160 MHz in the spec,
so it makes no sense to distinguish them. As no driver
uses them yet, this is also not a problem, just remove
them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.
Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.
This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
only require headroom space. Therefore, the tailroom-needed counter can
safely be decremented for most drivers.
The older incarnation of this patch (ca34e3b5) assumed that the above
holds true for all drivers. As reported by Christopher Chavez and
researched by Christian Lamparter and Larry Finger, this isn't a valid
assumption for p54 and cw1200.
Drivers that still require tailroom for ICV/MIC even when HW encryption
is enabled can use IEEE80211_KEY_FLAG_RESERVE_TAILROOM to indicate it.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Cc: Christopher Chavez <chrischavez@gmx.us>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211.git to get some changes that would otherwise
cause conflicts with new changes coming here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit ca34e3b5c8.
It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.
Cc: stable@vger.kernel.org
Fixes: ca34e3b5c8 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: Christopher Chavez <chrischavez@gmx.us>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Debugged-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since multicast frames are marked as no-ack, using
IEEE80211_TX_STAT_ACK to check if they have been
successfully transmitted by the driver is incorrect
since a driver can choose to ignore transmission status
for no-ack frames. This results in incorrect accounting
for such frames.
To fix this issue, this patch introduces a new flag
that can be used by drivers to indicate error-free
transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[add a note about not setting the flag for non-no-ack frames]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move IEEE80211_TX_CTL_PS_RESPONSE to info->control.flags since
this is used only in the TX path (by ath9k). This frees up
a bit which can be used for other purposes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used by drivers that cannot reliably map tx status
information onto specific skbs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This op works like .tx_status, except it does not need access to the
skb. This will be used by drivers that cannot match tx status
information to specific packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
