it will reduce exution time from 14ms to 2ms on ar9271
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use REG_RMW in ath9k_hw_analog_shift_rmw.
It will double execution speed on usb bus.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
insted of reading each register separatly
and waste 4ms on each operation, we can
use one shot read.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
REG_READ generate most overhead on usb bus. It send and read micro packages
and reduce usb bandwidth. To reduce this overhead we should read in batches.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function uses mixed styles for register names/numbers which
is make harder reading and optimisation.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since usb bus add extra delay on each request, a command
with read + write requests is too expensive. We can dramtically
reduce usb load by moving this command to firmware.
In my tests, this patch will reduce channel scan time
for about 5-10 seconds.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I changed REG_CR+2 and (MSR) to MSR because MSR is defined as (REG_CR + 2).
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Seems H/W report correctly firmware Autorun value only at initialization
stage. When we close interface and open it again, Autorun value is 0 and
we try to load firmware what kills the device. To fix clear
REQUIRE_FIRMWARE firmware flag, to do not load firmware again, once we
discover Autorun mode.
Reported-and-tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC needs to be registered only when BTCOEX is enabled.
This fixes the error reported by kbuild:
>> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined!
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With patch '960d6d08e39 "mwifiex: delay skb allocation for RX
until cmd53 over"' we no more pass skb parameter to MP aggregation setup
helper function. We instead pass length to be aggregated.
This patch fixes an issue where we were passing length parameter of NULL
skb to aggregation routine resulting into crash. We should instead pass
rx_len received from mp_regs.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are no known BCM4354 PCIe devices released so removing
support from the driver until proven otherwise.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently support was added for the BCM4345 SDIO chipset by
commit 9c51026509 ("brcmfmac: Add support for BCM4345 SDIO chipset")
however this was verified using a BCM43455 device, which is
a more recent revision of the chip. This patch assure that
older revisions are not probed as they would fail.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Syed Asifful Dayyan <syedd@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch added support for the BCM43430 802.11n SDIO chipset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BCM4356 PCIe wireless device was added recently but overlooked
the fact that the MODULE_FIRMWARE() macros were missing for the
firmwares needed by this device.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO uses a thread to handle all communication with the device,
for this data is exchanged between threads. This data needs proper
memory barriers to make sure that data "exchange" is going correct.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several host controllers supporting runtime-pm are causing issues
with our sdio wireless cards because they disable the sdio interrupt
upon going into runtime suspend. This patch avoids that by doing
a pm_runtime_forbid() call during the probe. Tested with Sony Vaio
Duo 13 which uses sdhci-acpi host controller.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's clear from the indenting that curly braces were intended here.
Fixes: e35000ead4 ('mwifiex: preprocess packets from TX queue')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter
to the rt2830 driver.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Pieter Truter <ptruter@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast is not yet properly supported for all connection types;
actually, only non-secure AP is supported. For all other cases,
fall back to old "pseudo-DMS" approach. Namely, for:
- PBSS
- secure connection
When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin
of the frame
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dedicated vring for multicast frames; this vring allocated for
AP and PBSS (both P2P GO and client) configurations
For short frames, use MCS0; for long - MCS1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync with the wmi definitions from the firmware team
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.
To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.
Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"echo" used to be called when no firmware loaded to the NIC,
this causes error output.
Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use temporal variable for often used vring->swhead;
and use proper index in debug printing - vring->swhead
used before was modified in wil_vring_advance_head
and then increased value was used in debug print
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cw1200 driver implements suspend and resume callbacks and assigns them
to the suspend and resume fields of the device_driver struct. These
callbacks are never actually called by anything though.
Modify the driver to properly use dev_pm_ops so that the suspend function
is actually executed upon suspend and drop the empty resume function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I've been getting this error when building mainline kernels using
Fedora's config files:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c: In function ‘_rtl88ee_init_mac’:
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:853:2: error: implicit declaration of function ‘rtl_hal_pwrseqcmdparsing’ [-Werror=implicit-function-declaration]
if (!rtl_hal_pwrseqcmdparsing(rtlpriv, PWR_CUT_ALL_MSK,
^
cc1: some warnings being treated as errors
scripts/Makefile.build:258: recipe for target 'drivers/net/wireless/rtlwifi/rtl8188ee/hw.o' failed
I'm not sure if this is the correct fix, but it does seem to allow the
build to complete. I suspect that this was broken by commit 34ed780a6a
(rtlwifi: Fix problems with building an allyesconfig). Most of the files
that removed the include of pwrseqcmd.h, added one for ../pwrseqcmd.h.
The rtl8188ee driver had it removed it but didn't add the include of the
file in the parent directory.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a MCI reset is done, make sure that AIC
is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the main AIC calibration function to
handle MCI_STATE_AIC_CAL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds a function to handle the
MCI message MCI_STATE_AIC_START.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a routine to handle the MCI_STATE_AIC_CAL_RESET
message.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since various MCI messages need to be
handled, along with driver-level support
in upper layers, disable AIC for now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for post-processing
the AIC calibration results.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the appropriate bits in the HW after
AIC calibration is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds routines to handle the MCI
message AIC_CAL_SINGLE, starting the required
HW calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various registers to control and check AIC
status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AIC can be disabled or enabled on a per-card
basis using MCI configuration, so register a function
to check its status.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are necessary for implementing AIC,
supported by chips like WB222.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch moves SKB allocation for RX packets from current
place i.e. after reading MP regs to place where we already
have read data from SDIO bus ie after cmd53.
mp_rx_aggr_setup has been modified accordingly to set
skb_arr to NULL.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Reviewed-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
