Add warning message to rsnd_kctrl_accept_runtime(), when kctrl
update is rejected due to corresponding dai-link is idle.
So that user can notice the reason of kctrl update failure.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[kuninori: adjust to upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clocking operations clk_get/set_rate, are non-atomic,
they shouldn't be called in soc_pcm_trigger() which is atomic.
Following issue was found due to execution of clk_get_rate() causes
sleep in soc_pcm_trigger(), which shouldn't be blocked.
We can reproduce this issue by following
> enable CONFIG_DEBUG_ATOMIC_SLEEP=y
> compile, and boot
> mount -t debugfs none /sys/kernel/debug
> while true; do cat /sys/kernel/debug/clk/clk_summary > /dev/null; done &
> while true; do aplay xxx; done
This patch adds support to .prepare callback, and moves non-atomic
clocking operations to it. As .prepare is non-atomic, it is always
called before trigger_start/trigger_stop.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
in_atomic(): 1, irqs_disabled(): 128, pid: 2242, name: aplay
INFO: lockdep is turned off.
irq event stamp: 5964
hardirqs last enabled at (5963): [<ffff200008e59e40>] mutex_lock_nested+0x6e8/0x6f0
hardirqs last disabled at (5964): [<ffff200008e623f0>] _raw_spin_lock_irqsave+0x24/0x68
softirqs last enabled at (5502): [<ffff200008081838>] __do_softirq+0x560/0x10c0
softirqs last disabled at (5495): [<ffff2000080c2e78>] irq_exit+0x160/0x25c
Preemption disabled at:[ 62.904063] [<ffff200008be4d48>] snd_pcm_stream_lock+0xb4/0xc0
CPU: 2 PID: 2242 Comm: aplay Tainted: G B C 4.9.54+ #186
Hardware name: Renesas Salvator-X board based on r8a7795 (DT)
Call trace:
[<ffff20000808fe48>] dump_backtrace+0x0/0x37c
[<ffff2000080901d8>] show_stack+0x14/0x1c
[<ffff2000086f4458>] dump_stack+0xfc/0x154
[<ffff2000081134a0>] ___might_sleep+0x57c/0x58c
[<ffff2000081136b8>] __might_sleep+0x208/0x21c
[<ffff200008e5980c>] mutex_lock_nested+0xb4/0x6f0
[<ffff2000087cac74>] clk_prepare_lock+0xb0/0x184
[<ffff2000087cb094>] clk_core_get_rate+0x14/0x54
[<ffff2000087cb0f4>] clk_get_rate+0x20/0x34
[<ffff20000113aa00>] rsnd_adg_ssi_clk_try_start+0x158/0x4f8 [snd_soc_rcar]
[<ffff20000113da00>] rsnd_ssi_init+0x668/0x7a0 [snd_soc_rcar]
[<ffff200001133ff4>] rsnd_soc_dai_trigger+0x4bc/0xcf8 [snd_soc_rcar]
[<ffff200008c1af24>] soc_pcm_trigger+0x2a4/0x2d4
Fixes: e7d850dd10 ("ASoC: rsnd: use mod base common method on SSI-parent")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To comply with the style of all kernel messages, add newline
to the end of every message.
Fixes: 70fb10529f ("ASoC: rsnd: add MIX (Mixer) support")
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd priv has many parameters. On __rsnd_dai_probe() it uses
rsnd_rdai_get() to get rdai pointer, but is using priv->daidrv
directly to get daidrvhv, but it is confusable for reader.
This patch adds rsnd_daidrv_get() to get daidrv from priv.
Now reader can understand that rdai and daidrv are related.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSICR has SWSP bit (= Serial WS Polarity) which decides WS pin 1st
channel polarity (low or hi). This bit shouldn't exchange after running.
Current SSI "parent" doesn't care SSICR, just controls clock only.
Because of this behavior, if platform uses SSI0 as playback,
SSI1 as capture, and if user starts capture -> playback order,
SSI0 SSICR::SWSP bit exchanged 0 -> 1 during captureing, and it makes
capture noise.
This patch cares SSICR on SSI parent, too.
Special thanks to Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If SSIs are sharing WS pin, it should has .symmetric_rates.
This patch sets it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidyup incoherence between MODULE_LICENSE and header license, too
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidyup incoherence between MODULE_LICENSE and header license, too
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidyup incoherence between MODULE_LICENSE and header license, too
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidyup incoherence between MODULE_LICENSE and header license, too
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tidyup incoherence between MODULE_LICENSE and header license, too
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the menu title to refer to "Renesas SoCs" instead of "SuperH", as
both SuperH and ARM SoCs are supported.
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is ARCH_RENESAS a more appropriate platform dependency for Renesas ARM
SoCs than the legacy ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the SUPERH
dependency.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SIU sound peripheral is used only on SuperH SH-Mobile platforms.
As both SUPERH and ARCH_SHMOBILE are set for these platforms, the SUPERH
dependency can be dropped.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is waiting udelay(50) x 1024 (= 50ms) for status check
in worst case, but it is overkill.
And we shouldn't use udelay() for 50us
(linux/Documentation/timers/timers-howto.txt)
Waiting maximum udelay(5) x 1024 (= 5ms) is very enough
for status check.
This patch fixes these issue.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4821d914fe ("ASoC: rsnd: use dma_sync_single_for_xxx() for
IOMMU") (= v1) which have been already reverted had supported IPMMU
support on rsnd driver.
Because memory allocating timing and DMAEngine access timing were
different, it used continuous memory and called dma map function by
itself.
OTOH, it is using DMA descriptor mode (= DMA cyclic mode), thus, there
was timing conflict between DMA sync/unsync and DMA transfer starting,
and it maked sound noise.
This patch supports IPMMU with coherent memory, and, it uses Audio DMAC
dev for allocating memory by snd_pcm_lib_preallocate_pages_for_all() to
indicate memory area to IPMMU.
One note is that Playback/Capture need each paired Audio DMAC dev.
Because of this, we need to keep each paired Audio DMAC dev when probing,
and use it when allocating each memory for IPMMU.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ssi.c is assuming below 2 things to probing HDMI node.
1) remote node is including "hdmi0" or "hdmi1" in node name
2) remote_ep->full_name is including full path name
But, these assumptions are broken by below
1) Node names should not use numerical suffixes
commit 6b5ac2f1cb ("arm64: dts: renesas: r8a7795: Drop bogus HDMI
node names suffixes")
2) node full_name no longer include full path name
commit a7e4cfb0a7 ("of/fdt: only store the device node basename
in full_name")
Because of these reasons, ssi.c can't probe HDMI on current kernel.
This patch probes HDMI0/1 by using its address.
Note is that we need to keep updating for this address for future
generation chip.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver is supporting Gen3. The difference between Gen1 and Gen2
were very big, but, between Gen2 and Gen3 are not so much.
Thus, it is assuming Gen2 and Gen3 have compatible, therefore,
there is no RSND_GEN3 and rsnd_is_gen3() macro.
But in the future, it will need Gen2 and Gen3 different operation,
and for Gen4.
This patch adds missing RSND_GEN3 and rsnd_is_gen3() macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_cmd_mod_get() is used from cmd.c only.
Let's makes it static function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The suspend/resume callbacks are now optional, leading to a warning
when they are unused:
sound/soc/sh/rcar/core.c:1548:12: error: 'rsnd_resume' defined but not used [-Werror=unused-function]
static int rsnd_resume(struct device *dev)
^~~~~~~~~~~
sound/soc/sh/rcar/core.c:1539:12: error: 'rsnd_suspend' defined but not used [-Werror=unused-function]
static int rsnd_suspend(struct device *dev)
This marks the as __maybe_unused to avoid the warning.
Fixes: f8a9a29c4f ("ASoC: rsnd: set pm_ops in hibernate-compatible way")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SET_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.suspend and .resume fields.
This makes driver working after restore from hibernation.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() is using dev_dbg(), but its message is sometimes
blocks nessesary other messages. If RSND_DEBUG_NO_DAI_CALL was
defined it will be suppressed by this patch.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC have under/over flow error handling, and its status is useful
for debuging. But sometimes it might be too much message,
and it might blocks necessity other information.
To avoid such situation, basically this patch indicates interrupt
status debug message if DEBUG was defined, but it will be suppressed
if RSND_DEBUG_NO_IRQ_STATUS was defined.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BRGCKR should use 0x80770000, instead of 0x80FF0000.
R-Car Gen2 xxx_TIMSEL should use 0x0F1F,
R-Car Gen3 xxx_TIMSEL should use 0x1F1F.
Here, Gen3 doesn't support AVD, thus, both case can use 0x0F1F.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI had shared counting pointer position method between PIO/DMA mode
before. But now DMA mode is using DMAEngine feature to get it.
Thus, this counting pointer position method is needed for only PIO mode.
We don't need to share code anymore.
This patch names PIO related functions as rsnd_ssi_pio_xxx(), and
merged/cleanuped each feature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is judging 16bit/24bit data by using
runtime->sample_bits, but it is indicating physical size,
not format size. This is confusable code.
This patch uses snd_pcm_format_width() to be more correct code.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Renesas sound device, DALIGN which exchanges channel position
is needed because SW and HW are using defferent data order if
16bit data. It is not needed when 24bit data.
rsnd_get_dalign() returns necessary value, but it was confusable
code. This patch makes it more simple.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
period_pos can always be calculated by byte_pos and
byte_per_period, there is no reason to maintain this
variable in rsnd_dai_stream.
This patch removes period_pos from rsnd_ssi and calculates
next_period_byte with consideration of actual byte_pos value.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there is race condition between set of byte_pos and wrap
it around when new buffer starts. If .pointer is called in-between
it will result in inconsistent pointer position be returned
from .pointer callback.
This patch increments buffer pointer atomically to avoid this issue.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Takashi Sakamoto <takashi.sakamoto@miraclelinux.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA handler had needed to calculate pointer before, but it doesn't
need now. Thus, we can remove unnecessary spin lock from DMAC handler.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs 8ch clock if TDM 6ch mode, and needs 2ch clock for
6ch or 8ch sound if Multi SSI mode. And these are related to before/after
CTU (= Channel Transfer Unit).
To calculate these we already has rsnd_runtime_channel_for_ssi() which
returns runtime necessary channels.
But, it based on runtime->channels which is not yet set when hw refine.
We need to use hw_params instead of runtime->xxx when hw refine,
and it is not needed after runtime was set.
This patch adds new hw_params on rsnd_dai_stream, and it will be removed
on rsnd_hw_params().
This is very temporary durty code, but it seems no choice at this point.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound driver should be stopped if unbinded during
playbacking/capturing. Otherwise clock open/close counter mismatch
happen.
One note is that we can't skip from remove function (= return -Exxx)
in such case if user used unbind. Because unbind function doesn't
check return value from each driver's remove function.
This means we must to stop and remove driver in remove function.
Now ASoC has snd_soc_disconnect_sync() for this purpose.
Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
register SSI_MODE is set when SSI works in TDM Extended,
but it isn't reset when SSI starts to work in other modes,
thus causes issues.
This patch clearss SSI_MODE register when SSI works in modes
other than TDM Extended.
Fixes: 186fadc132 ("ASoC: rsnd: add TDM Extend Mode support")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4821d914fe ("ASoC: rsnd: use dma_sync_single_for_xxx() for
IOMMU") had supported IOMMU, but it breaks normal sound "recorde"
and both PulseAudio's "playback/recorde". The sound will be noisy.
That commit was using dma_sync_single_for_xxx(), and driver should
make sure memory is protected during CPU or Device are using it.
But if driver returns current "residue" data size correctly on pointer
function, player/recorder will access to protected memory.
IOMMU feature should be supported, but I don't know how to handle it
without memory cache problem at this point.
Thus, this patch simply revert it to avoid current noisy sound.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlnx7QsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H6gB/9Kg6nfaNQDH3ScDO/0KXJevvc9DZUG
1Mgb6o866WQKVKwHL4/7PeUnwpaAh/Dr5KN7bFS7nImrZlHiJfv64Cmrrca+VMwa
O9SnAxbzMDN1MXV3uLDlmd5jJ2EETGnSSo31gjyOuFAmvWRYhtvN4QtoLRBQYYJ9
A32JAKYXKpdjYlIq8sssf1Ey9OcReho3klAc578Yw5qsuHTsB8yJ5SNy0YgmobCm
rNs+LcY9fBPQxY1nVW5iJ3L8oR9RXlUOdZy1I220i0q6+ku1nynbh64V8m7fFGmp
KQLIVvH8JGlqaGBidU47C3vwEnUN88y0+98i9dF4Hc26E+Ml3YNyL/z6
=TVgt
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloGGn8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BAsB/9tbgkbKpUVsWEQOTXDtz1VARb5+zxJ
zMRmYGdcfV+au4pmo07NwcxwFDqeLxmsd7dRM+eoPJGbxklD9rr9eL9tZiO1TI0B
jla9eyKO1aRjCD8dEDsQJEUjDGWWbrpYRvFjlTmYW5cf1vgE9Ta7QtwBN+mK+Ssn
1PtwfHg5lDffoCMGOgu/5Kah4QhzAIU1mM4Vg77VgsuScZEw5qMYJUncfkdsH6M5
JiQJpOQR/wNL4/IETodjhFzqhi9vlUvDEfmATNMpHMdHA//erUbphUt2bAjqVauM
zKTFTSN1vvW1GirJyxz4NiHXQ6upbpZPMDcPsfOzJhHw82OAwx/pp1QT
=bBtM
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.14-rc6' into asoc-linus
ASoC: Fixes for v4.14
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
# gpg: Signature made Thu 26 Oct 2017 15:11:23 BST
# gpg: using RSA key ADE668AA675718B59FE29FEA24D68B725D5487D0
# gpg: issuer "broonie@kernel.org"
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@debian.org>" [unknown]
# gpg: aka "Mark Brown <broonie@kernel.org>" [unknown]
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@linaro.org>" [unknown]
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
PTR_ERR(NULL) is success. Normally when a function returns both NULL
and error pointers, it means that NULL is not a error.
But, rsnd_dmaen_request_channel() returns NULL if requested resource
was failed.
Let's return -EIO if rsnd_dmaen_request_channel() was failed on
rsnd_dmaen_nolock_start().
This patch fixes commit edce5c496c ("ASoC: rsnd: Request/Release DMA
channel eachtime")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current rsnd driver has rsnd_mod_id() which returns mod ID,
and it returns -1 if mod was NULL.
In the same time, this driver has rsnd_mod_name() which returns mod
name, and it returns "unknown" if mod or mod->ops was NULL.
Basically these "mod" never be NULL, but the reason why rsnd driver
has such behavior is that DMA path finder is assuming memory as
"mod == NULL".
Thus, current DMA path debug code prints like below.
Here "unknown[-1]" means it was memory.
...
rcar_sound ec500000.sound: unknown[-1] from
rcar_sound ec500000.sound: src[0] to
rcar_sound ec500000.sound: ctu[2]
rcar_sound ec500000.sound: mix[0]
rcar_sound ec500000.sound: dvc[0]
rcar_sound ec500000.sound: ssi[0]
rcar_sound ec500000.sound: audmac[0] unknown[-1] -> src[0]
...
1st issue is that it is confusable for user.
2nd issue is rsnd driver has something like below code.
mask |= 1 << rsnd_mod_id(mod);
Because of this kind of code, some statically code checker will
reports "Shifting by a negative value is undefined behaviour".
But this "mod" never be NULL, thus negative shift never happen.
To avoid these issues, this patch adds new dummy "mem" to
indicate memory, and use it to indicate debug information,
and, remove unneeded "NULL mod" behavior from rsnd_mod_id() and
rsnd_mod_name().
The debug information will be like below by this patch
...
rcar_sound ec500000.sound: mem[0] from
rcar_sound ec500000.sound: src[0] to
rcar_sound ec500000.sound: ctu[2]
rcar_sound ec500000.sound: mix[0]
rcar_sound ec500000.sound: dvc[0]
rcar_sound ec500000.sound: ssi[0]
rcar_sound ec500000.sound: audmac[0] mem[0] -> src[0]
...
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI parent mod might be NULL. ssi_parent_mod() needs to care
about it. Otherwise, it uses negative shift.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When stop case, it was Playback, it need to check all data were
completely sent. But in Capture case, it might not receive data
anymore. SSISR::DIRQ check is not need for Capture case.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's use more common style to checking running/working
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_unprepare() is checking parameter by IS_ERR_OR_NULL().
clk NULL check is not needed on rsnd_mod_quit()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have rsnd_io_to_mod() macro. Let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG inputs clock from CLK{A,B,C,I} and outputs clock from
CLKOUT{0,1,2,3} which is selected by BRG{A,B}.
Now, ADG is assuming BRGA is for 44100Hz related clocks,
BRGB is for 48000Hz related clocks.
Clock related debug is very difficult/confusable.
This patch cleanups clock related debug info.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU/MIX/DVC are directly using rsnd_kctrl_cfg_m/s to control
val etc, but it is difficult to read/understand.
And there was no uniformity in access method.
This patch adds new rsnd_kctrl_xxx() and implements uniformed access
method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that when used with DT, there's always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both DVC/MIX have Volume Ramp Control. This patch supprts MIX
Volume Ramp. One note is that main purpose of MIX Volume Ramp
is to reduce noise, thus, MIX Ramp range is very few if you
compare to DVC Volume Ramp (DVC = 5bit, MIX = 4bit).
You can use MIX Volume Ranp like below
amixer set "MIX Ramp Up Rate" "0.125 dB/1 step"
amixer set "MIX Ramp Down Rate" "0.125 dB/1 step"
amixer set "MIX Ramp" on
aplay xxx.wav &
amixer set "MIX",0 80% // DAI0 Volume Down
amixer set "MIX",1 100% // DAI1 Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC is supporting Volume Ramp Rate, and MIX has Volume Ramp
but not yet supported. To support MIX Volume Ramp, we want to
share Rate List since DVC/MIX are using almost same list.
This patch move DVC specific Volume Ramp Rate List to core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same CTU might be used few times if system/platform is using MIX.
For example below case.
DAI0 playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
DAI1 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
This case, ALSA will have CTU,0 and CTU,1 kcontrol interfaces,
but these are same CTU. This is confusing.
This patch adds new flags and avoid such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same DVC might be used few times if system/platform is using MIX.
For example below case.
DAI0 playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
DAI1 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
This case, ALSA will have DVC,0 and DVC,1 kcontrol interfaces,
but these are same DVC. This is confusing.
This patch adds new flags and avoid such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI is using rsnd_ssi_flags_xxx() macro to control flags.
But it is useful macro not only for SSI. This patch replace it
to more generic rsnd_flags_xxx().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current device tree representation of the R-Car SSI assumes that they
are numbered consecutively, starting from 0. Alas, this is not the case
with the R8A77995 (D3) SoC which SSI1/SSI2 aren't present. In order to
keep the existing device trees working, I'm suggesting to use a disabled
node for SSI0/SSI1. Teach the SSI probe to just skip disabled nodes.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car sound DMA will be used from SSI/SRC.
dma.c doesn't alloc DMA handler in .probe timing, because we don't
know what kind of DMA transfer will be used then.
Thus, SSI/SRC have *rsnd_mod for DMA. rsnd_dma_attach() will allocate
it and attach it to system.
It will be PIO mode if it can't alloc DMA handler.
In case of MIX is used, rsnd_dma_attach() will be called twice from SSI.
To avoid duplicate allocation, current rsnd_dma_attach() is checking
allocated DMA handler. This DMA related operation is a little bit
difficult to understand.
This patch adds new rsnd_dma_alloc() and separates allocation and attach
for readable code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG driver is over-writing flags. This patch fixes it.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make this const as it is only stored in the ops field of a
snd_soc_dai_link structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only passed as the 2nd argument to the
function snd_soc_set_runtime_hwparams, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/soc.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are either passed as the 2nd argument to
the function devm_snd_soc_register_platform or snd_soc_register_platform,
and the arguments are of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each module's dai callback function availability is controlled
by mod->status. For example "always called", "call once".
In .probe/.remove case, it needs to be called always, because
.probe will call xxx_attach() function on .probe, especially
if platform is using MIXer.
For example, below case, MIX0/DVC0/SSI0 needs to be called twice.
playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
But in this case, SSI0 will call request_irq() twice.
This patch add new RSND_SSI_PROBED flag and control it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_ssi_mode_flags() is not useful. This patch adds
new rsnd_ssi_flags_has/add() macro for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 701172dca1 ("ASoC: rsnd: don't use devm_request_irq() for SSI")
exchanged devm_request_irq() to request_irq() for SSI, because SSI will
fallback into PIO mode if DMA doesn't work.
But, because of it, PIO mode needed to call free_irq() when removing,
not only DMA mode.
This patch call free_irq() both PIO/DMA. Otherwise, rsnd IRQ handler
will be increased if user tried many unbind/bind.
Fixes: 701172dca1 ("ASoC: rsnd: don't use devm_request_irq() for SSI")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1f8754d4da ("ASoC: rsnd: don't call free_irq() on
Parent SSI") fixed Parent SSI duplicate free_irq().
But on Renesas Sound, not only Parent SSI but also Multi SSI
have same issue.
This patch avoid duplicate free_irq() if it was not pure SSI.
Fixes: 1f8754d4da ("ASoC: rsnd: don't call free_irq() on Parent SSI")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen3 sound device can use TDM 16ch, but its usage is very
limited. It is not yet supported.
Let's remove unexpected/unsupported channel settings for now.
This patch makes xx_ADINR register settings sanity without
runtime check.
R-Car Gen3 datasheet
40.4.7 Note on Usage of the SSIU Module
When an SSIU module is used in "TDM-16ch mode",
only the transfer with the external memory is available.
Reported-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of SSI0 playback, SSI1 capture, SSI0 might be shared for
clock output if clock master mode.
Current rsnd driver had been assumed that SSI clock contiguous
output which is needed for SSI parent needs SSICR::EN (SSI module
enable) bit.
But, this bit controls data input/output, not for clock.
Clock contiguous output needs SSICR : FORCE, SCKD, SWSD,
and SSIWSR : CONT. Not SSICR : EN.
Because of this wrong assumption, and insufficient control, on current
code, for example, if it starts SSI0(playback) -> SSI1(capture) order,
SSI0 SSICR::EN bit will temporarily be 0.
It causes playback side underrun error. This is bug.
We can reproduce this issue with SSI+SRC (without DVC), and capture
during playback operation.
This patch fixup current (wrong) assumption, and control SSICR::EN bit
correctly.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For example SSI0/SSI1 case, SSI1 can share pin with SSI0.
And then, SSI1 needs SSI0's clock.
This clock controlling is very picky and difficult to understand
in current code.
This patch adds new rsnd_ssi_can_output_clk() macro,
the code will be more understandable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it the same style as other functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG is registering fixed rate clock for audio_clkout, but it had not
been unregister clock when removing.
Salvator-X board is using ak4613 driver now, and it supports
hw_constraints from commit 907cd8809e ("ASoC: ak4613: add
hw_constraint rule for Sampling Rate").
And this calculation is using input clk. This ak4613 input clock is
ADG clkout on Salvator-X.
Because ADG had not been unregister clkout when unbinding, it receives
fixed rate clk register error when re-binding.
Thus, ak4613 can't get correct input clock, and hw_constraints will be
failed after re-binding.
This means Salvator-X board can't use sound after unbind/bind.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has snd_pcm_ops::open and snd_soc_dai_ops::startup,
but, these are called from soc_pcm_open in same time.
This patch merge these into rsnd_soc_dai_startup()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd kctrl is using both .private_value (for rsnd_kctrl_cfg)
and .private_data (for rsnd_mod) on snd_kcontrol.
But only 1 private data (= rsnd_kctrl_cfg) can be enough if it has
rsnd_mod pointer.
This patch doesn't use private_value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b047e1cce8 ("ASoC: ac97: Support multi-platform AC'97")
modified hac_soc_platform_probe(), but "int ret" was missed.
This patch adds missing "int ret", otherwise, we will get
linux/sound/soc/sh/hac.c: In function 'hac_soc_platform_probe':
linux/sound/soc/sh/hac.c:318: error: 'ret' undeclared (first use in this function)
linux/sound/soc/sh/hac.c:318: error: (Each undeclared identifier is reported only once
linux/sound/soc/sh/hac.c:318: error: for each function it appears in.)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unnecessary static on local variable ops.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
3211 680 64 3955 f73 sound/soc/sh/rcar/ssiu.o
after:
text data bss dec hex filename
3207 592 0 3799 ed7 sound/soc/sh/rcar/ssiu.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
for_each_child_of_node performs an of_node_get on each iteration, so a
jump out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1;
identifier l;
@@
for_each_child_of_node(e1,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? goto l;
)
...
}
...
l: ... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This dev_pm_ops structure is only stored in the pm field of a
device_driver structure. This field is declared const, so
dev_pm_ops structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
Don't populate the arrays path and cmd_case on the stack but make
them static const. Makes the object code smaller:
Before:
text data bss dec hex filename
2673 624 0 3297 ce1 sound/soc/sh/rcar/cmd.o
After:
text data bss dec hex filename
2398 768 0 3166 c5e sound/soc/sh/rcar/cmd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
8172 920 0 9092 2384 sound/soc/sh/rcar/core.o
File size After adding 'const':
text data bss dec hex filename
8364 728 0 9092 2384 sound/soc/sh/rcar/core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes this WARNING
sound/soc/sh/rcar/ssi.c:285:5-14: WARNING: Unsigned expression\
compared with zero: main_rate < 0
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.
To support such feature, this patch adds new
rsnd_soc_hw_rule/constraint() which adds hw rule of Channel and
Sampling Rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.
To support such feature, this patch adds new rsnd_ssi_clk_query().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.
To support such feature, it needs SSI clock query feature, and it needs
ADG clock query feature. Current ADG has rsnd_adg_ssi_clk_try_start()
and it is doing similar things, but it try to setup ADG register in
same time. This is not needed.
This patch adds new rsnd_adg_clk_query() and separates query feature
and register setting feature in adg.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver has slots and slots_num in
struct rsnd_dai, but these are very un-understandable naming
(It had named from TDM slots).
In this driver, the "slots" means total usable channels, and
"stot_num" means SSI lane number if Multi SSI was used.
To more understandable code, this patch renames "slots" to
"max_channels", and "slots_num" to "ssi_lane", and replaces related
functions name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() macro is using "priv" inside.
Thus, if caller function doesn't have "priv" related operation, strange
phenomenon occur which code is using "priv", but compiler indicates
"unused variable 'priv'".
>From code point of view, it is not problem, but it is very confusable.
This patch removes "priv" from rsnd_dai_call() macro, and adds "priv"
on caller function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC/DVC/CTU adds kctrl for each device,
and SRC can adjust its sampling rate during playback,
thus, this feature should be enabled only *during* playback.
This patch controls it more clearly
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas Sound device *Hardware* L/R and Linux *Software* L/R are
inverted. Because of this background, it needs to convert L/R.
Then, DVC needs *Hardware* L/R, and Linux needs *Software* L/R.
Because Playback/Capture needs different timing, and there is no
explanation about it on source code / git log, this patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is sharing pointer related code between
PIO / DMA. But, it is used only PIO mode now, no longer needed.
This patch cleanup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver updates pointer when DMA transfer was finished
in DMA transfer mode. But PulseAudio requests more accurate
pointer update when timer mode.
This patch consider about DMA transfer residue and update more
accurate pointer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi_non_ops is never used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_kcontrol_new structures as const as they are only passed an
argument to the function snd_ctl_new1. This argument is of type const,
so snd_kcontrol_new structures having this property can be made const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct snd_kcontrol_new x@p={...};
@ok@
identifier r.x;
position p;
@@
snd_ctl_new1(&x@p,...)
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct snd_kcontrol_new x;
Cross compiled these files:
sound/aoa/codecs/tas.c - powerpc
sound/mips/{hal2.c/sgio2audio.c} - mips
sound/ppc/{awacs.c/beep.c/tumbler.c} - powerpc
sound/soc/sh/siu_dai.c - sh
Could not find an architecture to compile sound/sh/aica.c.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 25165f79ad ("ASoC: rsnd: enable clock-frequency for both
44.1kHz/48kHz") supported both 44.1kHz/48kHz for AUDIO_CLKOUTx,
but it didn't care its parent clock name.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 90431eb49b ("ASoC: rsnd: don't use PDTA bit for 24bit on SSI")
fixups 24bit mode data alignment, but PIO was not cared.
This patch fixes PIO mode 24bit data alignment
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car Gen3 can output HDMI sound if SSIU/SSI are connected to
R-Car built-in HDMI device (R-Car Gen3 built-in HDMI device will be
controlled by DRM/KMS driver).
If SSIx was connected to HDMI0/1 on DT, SSI driver will detect it
automatically by this patch.
Note is that now Renesas R-Car sound driver is assuming that it is
using OF-graph base simple card for HDMI sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable OF-graph base DT on rsnd driver, and to keep compatible
previous normal sound card style, it need to support both
"rcar_sound,dai" and "ports" (or "port") on DT.
This patch parses both style.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable OF-graph base DT on rsnd driver, and to keep compatible
previous normal sound card style, it need to support both
"rcar_sound,dai" and "ports" (or "port") on DT.
This patch modify rsnd_dai_of_node() to parse
"rcar_sound,dai" and "ports" (or "port") as phase 1. It can detect
graph base style, but do nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If SSI uses shared pin, some SSI will be used as parent SSI.
Then, normal SSI's remove and Parent SSI's remove
(these are same SSI) will be called when unbind or remove timing.
In this case, free_irq() will be called twice.
This patch solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI uses PDTA bit which indicates data that Input/Output
data are Right-Aligned. But, 24bit sound should be Left-Aligned
in this HW. Because Linux is using Right-Aligned data, and HW uses
Left-Aligned data, current 24bit data is missing lower 8bit.
To fix this issue, this patch removes PDTA bit, and shift 8bit
in necessary module
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc 4.1.2:
sound/soc/sh/fsi.c:304: warning: ‘fsi_stream_is_play’ declared inline after being called
sound/soc/sh/fsi.c:304: warning: previous declaration of ‘fsi_stream_is_play’ was here
Move fsi_stream_is_play() up to fix this, removing the need for a
forward declaration as well.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without this patch, gcc 4.9.x says
sound/soc/sh/rcar/cmd.c: In function 'rsnd_cmd_init':
sound/soc/sh/rcar/cmd.c:85:14: warning: array subscript is below array\
bounds [-Warray-bounds]
data = path[rsnd_mod_id(src)] |
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() is counting the called number of start/stop functions.
nolock_stop should be called if nolock_start was failed.
Otherwise, nolock_start doesn't called in 2nd play.
This patch solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit d7f298197a
("ASoC: rcar: fixup of_clk_add_provider() usage for multi clkout")
added adg->clkout[i] = ERR_PTR(-ENOENT),
but, adg->clkout[i] are assumed NULL or clk pointer.
This patch fix it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clkout-lr-asynchronous is AUDIO_CLKOUT related property, thus, it
should be handled by rsnd_adg_get_clkout().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before, src.c cares SRC and SSIU, but now SSIU is cared by ssiu.c by
commit c7f69ab536 ("ASoC: rsnd: use mod base common method on SSIU").
This patch removes mismatched explanation for SRC/SSIU from src.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
25165f79ad
("ASoC: rsnd: enable clock-frequency for both 44.1kHz/48kHz")
supports both 44.1kHz/48kHz clock-frequency settings for ADG
which will be used for AUDIO_OLKOUTn.
But some board doesn't need it, thus, it is not mandatory.
But, above patch didn't care about the case of "clock-frequency" DT
property was not present.
This patch ignores ADG settings if AUDIO_OLKOUTn was not used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[Kuninori: tidyup not to break non AUDIO_OLKOUTn case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current clock-frequency allows only 1 clock, but ADG can
handle both 44.1kHz/48kHz base clocks. This patch enables these.
On Salvator-X board, AUDIO_CLKOUT which is generated by ADG
is connected to ak4613 MCKI, and it should be synchronized with
LRCK. Thus, we need both 44.1kHz/48kHz base clock-frequency.
Otherwise, either one sounds strange in high frequency sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_make_sure() will be used any situation,
thus, under DEBUG is not realistic.
This patch move it to non DEBUG area
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using rsnd_kctrl_new_m/s/e function,
but the differences are very few.
This patch merge these rsnd_kctrl_new_m/s/e into rsnd_kctrl_new
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current src->convert_rate will be set on .hw_param, and
be reset on .quit timing.
But, .hw_param will not be called again if user did Ctrl-Z + fg.
It should be reset on initial of .hw_param to keep its value.
Here, ctu.c already do this.
This patch solves this issue, other wise, MIXed sound will be
strange if user did like below.
> aplay -D plughw:0,0 sound_44100.wav &
> aplay -D plughw:0,1 sound_96000.wav
> Ctrl-Z
> fg # 96kHz will be played as 44.1kHz
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adg is calling of_clk_add_provider() when probe time,
thus, remove should call of_clk_del_provider(), it doesn't now.
This patch fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg is calling of_clk_add_povider() multiple times,
but it is not correct usage. This patch fixup its parameter
and call it once.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rcar driver is trying to remove kctrl when remove time.
But, 1) rcar driver can't/shouldn't remove before removing sound
card driver, 2) sound card driver will call snd_ctl_dev_free()
and removes all kctrls by snd_ctl_remove().
Thus, rsnd_kctrl_remove() is not necessary. Current implementation
will get Oops when removing rcar driver after sound card.
This patch fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Datasheet is indicating "SSICR.CKDV = 000 is invalid when
SSIWSR.WS_MODE = 1 or SSIWSR.CONT = 1".
Current driver will set CONT, thus, we shouldn't use CKDV = 000.
This patch fixup it.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2a3af642eb20("ASoC: rcar: clear DE bit only in PDMACHCR...")
added rsnd_dmapp_bset(), but it used copy-paste. Thus, it had
unnecessary "volatile", and had below warning on x86.
This patch fix it.
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_bset':
>> sound/soc/sh/rcar/dma.c:463:21: warning: passing argument 1 of \
'ioread32' discards 'volatile' qualifier from pointer target \
type [-Wdiscarded-qualifiers]
u32 val = ioread32(addr);
^~~~
In file included from arch/x86/include/asm/io.h:203:0,
from arch/x86/include/asm/realmode.h:5,
from arch/x86/include/asm/acpi.h:33,
from arch/x86/include/asm/fixmap.h:19,
from arch/x86/include/asm/apic.h:10,
from arch/x86/include/asm/smp.h:12,
from include/linux/smp.h:59,
from include/linux/topology.h:33,
from include/linux/gfp.h:8,
from include/linux/idr.h:16,
from include/linux/kernfs.h:14,
from include/linux/sysfs.h:15,
from include/linux/kobject.h:21,
from include/linux/of.h:21,
from include/linux/of_dma.h:16,
from sound/soc/sh/rcar/dma.c:12:
include/asm-generic/iomap.h:31:21: note: expected 'void *' \
but argument is of type 'volatile void *'
extern unsigned int ioread32(void __iomem *);
^~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car datasheet indicates "Clear DE in PDMACHCR" for transfer stop,
but current code clears all bits in PDMACHCR.
Because of this, DE bit might never been cleared,
and it causes CMD overflow. This patch fixes this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the problem that the missing value of the route path
setting table and incorrect values are set in the CMD_ROUTE_SELECT
register.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
[Kuninori: shared data on MIX and non-MIX case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI8 is is sharing pin with SSI7, and nothing to do for SSI_MODEx.
It is special pin and it needs special settings whole system,
but we can't confirm it, because we never have SSI8 available board.
This patch fixup SSI_MODEx settings error for SSI8 on connection test,
but should be confirmed behavior on real board in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, this function cannot fail for the ADG case. Still, let's
apply defensive programming techniques to make sure we fail gracefully
whenever rsnd_mod_init() gets extended with another failure case.
Reported by Coverity (CID 1397893).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
