There are different revisions of the same chipset. For example S2MPS13 has
more than 2 revisions. They differ slightly in regulator constraints.
Print the revision number to easily find which PMIC is used on the board.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the case of a device tree config the code uses the device ID
from the DT entry to check which codec is required but when storing
the ID into struct arizona it was always using the non-DT SPI device
table to get an ID.
This patch changes the code to store the correct ID into struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the use of #ifdefs around each case statement of the chip ID
and type validation switches.
We must ensure that the contained code still compiles to nothing if
support for that codec was not built into the kernel, to prevent
creation of link references to missing functions. So the ifdefs are
replaced with a use of the IS_ENABLED() macro.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The code was using a switch on the code type to execute
one of several mfd_add_devices() calls. We're already
switching on the code type earlier in the function to
select the correct patch function so we can roll selection
of the mfd device table into the same switch.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the declared codec type doesn't match the detected type
we issue a log message but carry on registering the device,
so a dev_warn() is appropriate rather than a dev_err()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently runtime_suspend will fully power off the codec if
the jack detection is not enabled. Not all future codecs will
have jack detection so to prepare for these codecs this patch
factors out the check so that it be called as needed in the
existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently DCVDD isolation is enabled and disabled for
runtime_suspend and runtime_resume. Future codecs will not
have the isolation control so to prepare for these codecs
this patch factors out the isolation control allowing it to
be called as needed in the existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is required since
commit 7e50711993 ("mfd: tps6105x: Use i2c regmap to access registers").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We were getting build warning about unused variable 'ret'.
The commit c749db571dcf has removed the use of ret but missed removing
the variable which is unused now.
Fixes: c749db571dcf ("mfd: lm3533: Simplify function return logic")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename get_device_type() to da9062_get_device_type().
This function is only used in this file so make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver depends on ARCH_NOMADIK but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Definitions for GPIO registers 8, 9, 10, 11, 12 and 13 are added into
the register header file.
- DA9052_GPIO_8_9_REG 25
- DA9052_GPIO_10_11_REG 26
- DA9052_GPIO_12_13_REG 27
A modification is also made to the MFD core code to define these registers
as readable and writable. The functions for da9052_reg_readable() and
da9052_reg_writeable() have had their case statements altered to include
these new registers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The call to kstrtoul() will corrupt memory on 64 bit systems because an
int is 4 bytes and a long is 8.
Also it's not a good idea to let users trigger a dev_err() because it
just ends up flooding /var/log/messages so I removed the printk.
Fixes: 2ddd2086ea9c ('mfd: add Intel Broxton Whiskey Cove PMIC driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
tps6105 driver provides two cells. One is for GPIO and another one is
for selected mode depending on platform data. When tps6105x is used in
GPIO-only mode, this driver calls mfd_add_devices() with mfd_cell
.name == NULL. This value causes an oops in platform_device_register()
later.
The following patch adds a mfd_cell for each possible mode thereby
excluding .name assignment in runtime.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver handles wakeup irq correctly using irq_set_irq_wake. There's
no need to use IRQF_NO_SUSPEND while registering the interrupt.
This patch removes the use of IRQF_NO_SUSPEND flag.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The lpc_ich_cells array gives the wrong impression about the
relationship between the watchdog and GPIO devices. They are
completely distinct devices, so this patch separates the
array into distinct mfd_cell structs per device.
A side effect of removing the array, is that the lpc_cells enum
is no longer needed.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver for Intel Broxton Whiskey Cove PMIC,
which is specially accessed by hardware IPC, not a generic
I2C device
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has a I2C device id table that is used to create the module
aliases which already contains a "rt5033". So the alias is not needed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver has a I2C device id table that is used to create the module
aliases and also "bcm590xx" isn't a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add tps65217 battery charger subdevice.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove defaults for a bunch of volatile registers and remove
ARIZONA_CTRL_IF_SPI_CFG_1 from the readable list since it doesn't exist
on wm8998 which is I2C only.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some Arizona devices have a hardware ANC block present. This patch adds
the registers necessary to configure this hardware block.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The type of the data for the main Arizona IRQ chip should be struct
arizona not struct regmap_irq_chip_data. The bug is harmless but should
probably be corrected anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver always checks for pdata being NULL except in one place.
Add a check to prevent a possible NULL pointer deference error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduced by:
commit 8019ff6cfc ("regmap: Use reg_sequence for multi_reg_write / register_patch")
Interacting with:
commit 561629755a21 ("mfd: arizona: Add support for WM8998 and WM1814")
commit 81207880ce ("mfd: wm5110: Add register patch for rev E and above")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the
PWM channels. This oneliner was missing in the case-switch, making
it impossible to enable the PWM channel output.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
added clock handling for the 32k clock from palmas-clk. However, that
patch did not consider a typical situation where twl6040 is built-in,
and palmas-clk is a loadable module like we have in omap2plus_defconfig.
If palmas-clk is not loaded before twl6040 probes, we will get a
"clk32k is not handled" warning during booting. This means that any
drivers relying on this clock will mysteriously fail, including
omap5-uevm WLAN and audio.
Note that for WLAN, we probably should also eventually get
the clk32kgaudio for MMC3 directly as that's shared between
audio and WLAN SDIO at least for omap5-uevm. It seems the
WLAN chip cannot get it as otherwise MMC3 won't get properly
probed.
Fixes: 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip identification support for 88PM860 device
to the pm80x_chip_mapping table.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Documentation/devicetree/bindings/mfd/cros-ec.txt DT binding doc lists
"google,cros-ec-i2c" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the I2C
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Intel Galileo Gen2 the GPIO expanders are connected to the i2c bus. For
those devices the ACPI table has specific parameters that refer to an actual
i2c host controller. Since MFD now copes with that specific configuration we
have to provide a necessary information how to distinguish devices in ACPI
namespace. Here the _ADR values are provided.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo boards the GPIO expander is connected to i2c bus. Moreover it
is able to generate interrupt, but interrupt line is connected to GPIO. That's
why we have to have GPIO driver in place when we will probe i2c host with
device connected to it.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is at least one board on the market, i.e. Intel Galileo Gen2, that uses
_ADR to distinguish the devices under one actual device. Due to this we have to
improve the quirk in the MFD core to handle that board.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch modifies tps6105x and associated function driver to use regmap
instead of operating directly on i2c.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If i2c_new_dummy() fails in max77843_chg_init(), an PTR_ERR(NULL) is
returned which is 0. So the function was wrongly returning a success
value instead of an error code.
Cc: stable@vger.kernel.org # 4.1
Fixes: c7f585fe46 ("mfd: max77843: Add max77843 MFD driver core driver")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jim Davis reported the compilation error with a random configuration which
apparently has CONFIG_PM=y and CONFIG_PM_SLEEP=n. With that conditions we have
missed definition of INTEL_LPSS_SLEEP_PM_OPS macro. Add it here.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On wm5110/8280 some additional settings are required to get accurate
measurements at the top end of the headphone detection range. This patch
adds the bits required for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The switch is typically used in conjunction with the MICDET clamp in
order to suppress pops and clicks associated with jack insertion.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The newer devices support using a software comparison to determine
whether a 3/4 pole jack is present. Add the registers necessary for
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-
related changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition
is for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It
was initiated by lockdep warning, but resulted in a good cleanup in
the end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/sXs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-related
changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition is
for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It was
initiated by lockdep warning, but resulted in a good cleanup in the
end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier"
* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
drm/i915: Add locks around audio component bind/unbind
drm/i915: Drop port_mst_index parameter from pin/eld callback
ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
ALSA: hda - Wake the codec up on pin/ELD notify events
ALSA: hda - allow codecs to access the i915 pin/ELD callback
drm/i915: Call audio pin/ELD notify function
drm/i915: Add audio pin sense / ELD callback
ASoC: zx296702-i2s: Fix resource leak when unload module
ASoC: sti_uniperif: Ensure component is unregistered when unload module
ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
ASoC: Clean up docbook warnings
ASoC: txx9: Convert to devm_snd_soc_register_platform
ASoC: pxa: Convert to devm_snd_soc_register_platform
ASoC: nuc900: Convert to devm_snd_soc_register_platform
ASoC: blackfin: Convert to devm_snd_soc_register_platform
ASoC: au1x: Convert to devm_snd_soc_register_platform
ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
...
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
* acpi-pm:
ACPI / bus: Move duplicate code to a separate new function
mfd: Add support for Intel Sunrisepoint LPSS devices
dmaengine: add a driver for Intel integrated DMA 64-bit
mfd: make mfd_remove_devices() iterate in reverse order
driver core: implement device_for_each_child_reverse()
klist: implement klist_prev()
Driver core: wakeup the parent device before trying probe
ACPI / PM: Attach ACPI power domain only once
PM / QoS: Make it possible to expose device latency tolerance to userspace
ACPI / PM: Update the copyright notice and description of power.c
The biggest changes in the core this time around have been some
refactorings that move us towards being able to drop the list of
regulators maintained by the core and instead just use the driver model
list maintained for the class devices for regulators which will make the
code smaller and avoid some potential bugs. Otherwise another fairly
quiet release for the regulator API, highlights include:
- A new API for setting voltages based on a minimum, target, maximum
triplet.
- Support for continuous voltage ranges rather than tables of explicit
steps in the PWM regulator, requiring less explicit configuration.
- New driver support for Dialog DA9215, Maxim 77843, Mediatek MT6311
and Qualcomm RPM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV5DCWAAoJECTWi3JdVIfQDgYH/3mNwtRcwslt8M1L8lzRVyf1
gRrJY5r4EUOcqqsLnQvDHdjgO2yowEolEd3Hd/GElZqzeFgwXaQ62kHwgqnvOt9k
O0l99FbU6ECpB56tSENrV1lfvBTlld9bEhq9NhxvNiWAdpGPqIcjvXfSH28GssJ0
NGr4Yt/A1DG6GsOWxKSODX56WJXJn4emKx3vHH+leUClNWwQVK6JunTmj5IPKLxW
K94Ke41L3JgAy18TLqvFNlTAC22QaHFaM8ul9v7gnPW+S8Bx15MCQz16rMkGViZV
c/DyCu69qCVFLI1svRrvB5oq700QT0GT6jANCVmw+CrkIkESwjS39kX861H6hk8=
=vrVx
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The biggest changes in the core this time around have been some
refactorings that move us towards being able to drop the list of
regulators maintained by the core and instead just use the driver
model list maintained for the class devices for regulators which will
make the code smaller and avoid some potential bugs.
Otherwise another fairly quiet release for the regulator API,
highlights include:
- a new API for setting voltages based on a minimum, target, maximum
triplet
- support for continuous voltage ranges rather than tables of
explicit steps in the PWM regulator, requiring less explicit
configuration
- new driver support for Dialog DA9215, Maxim 77843, Mediatek MT6311
and Qualcomm RPM"
* tag 'regulator-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (70 commits)
regulator: mt6311: fix platform_no_drv_owner.cocci warnings
regulator: ltc3589: Remove unnecessary MODULE_ALIAS()
regulator: ad5398: Remove unnecessary MODULE_ALIAS()
regulator: pfuze100: Remove unnecessary MODULE_ALIAS()
regulator: core: use debug level print in regulator_check_drms
regulator: lp872x: handle error case
regulator: lp872x: use the private data instead of updating I2C device platform data
regulator: isl9305: Export OF module alias information
regulators: max77693: register driver earlier to avoid deferred probe
regulator: qcom_smd: Set n_voltages for pm8941_lnldo
regulator: core: Use IS_ERR_OR_NULL()
regulator: core: Define regulator_set_voltage_triplet()
regulator: Regulator driver for the Qualcomm RPM
regulator: pbias: Fix broken pbias disable functionality
regulator: core: Spelling fix
regulator: core: Use class device list for regulator_list in late init
regulator: core: Move more deallocation into class unregister
regulator: core: Reduce rdev locking region when releasing regulator
Input: Remove the max77843 haptic driver
Input: max77693: Add support for Maxim 77843
...
* new reset driver for ZTE SoCs
* add support for sama5d3 reset handling
* overhaul of twl4030 charger driver
* misc. fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ENTy
-----END PGP SIGNATURE-----
Merge tag 'for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
- new reset driver for ZTE SoCs
- add support for sama5d3 reset handling
- overhaul of twl4030 charger driver
- misc fixes and cleanups
* tag 'for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (35 commits)
bq2415x_charger: Allow to load and use driver even if notify device is not registered yet
twl4030_charger: fix compile error when TWL4030_MADC not available.
power: bq24190_charger: Fix charge type sysfs property
power: Allow compile test of GPIO consumers if !GPIOLIB
power: Export I2C module alias information in missing drivers
twl4030_charger: Increase current carefully while watching voltage.
twl4030_charger: add ac/mode to match usb/mode
twl4030_charger: add software controlled linear charging mode.
twl4030_charger: enable manual enable/disable of usb charging.
twl4030_charger: allow max_current to be managed via sysfs.
twl4030_charger: distinguish between USB current and 'AC' current
twl4030_charger: allow fine control of charger current.
twl4030_charger: split uA calculation into a function.
twl4030_charger: trust phy to determine when USB power is available.
twl4030_charger: correctly handle -EPROBE_DEFER from devm_usb_get_phy_by_node
twl4030_charger: convert to module_platform_driver instead of ..._probe.
twl4030_charger: use runtime_pm to keep usb phy active while charging.
rx51-battery: Set name to rx51-battery
MAINTAINERS: AVS is not maintained via power supply tree
power: olpc_battery: clean up eeprom read function
...
The mask cache must be initialised in the generic IRQ chip,
otherwise enabling one channel will actually enable all
channels when the empty mask cache is written.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Documentation/devicetree/bindings/mfd/cros-ec.txt DT binding doc lists
"google,cros-ec-spi" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the SPI
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Documentation/devicetree/bindings/mfd/stmpe.txt DT binding doc lists
"st,stmpe[610|801|811|1601|2401|2403]" as valid compatible strings but
the corresponding driver does not have an OF match table. Add the table
to the driver so the SPI core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD_CROS_EC symbol select CHROME_PLATFORMS and CROS_EC_PROTO but
that caused a Kconfig unmet direct dependencies warning since these
symbols could only be selected for X86 || ARM.
The fix it, the CHROME_PLATFORMS dependencies were relexed on commit
d12bbcd3ea ("platform/chrome: Don't make CHROME_PLATFORMS depends
on X86 || ARM") but that was found to be wrong and the correct fix
is to add the needed dependencies to the MFD_CROS_EC config symbol.
There are only x86 and ARM based Chromebooks so to avoid showing up
the config option on unsupported platforms, make the symbol depend on
these architectures. Also add a || COMPILE_TEST so it can have build
coverage on other platforms.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC SPI and I2C transport drivers depends on CROS_EC_PROTO
but MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since these drivers already depend on MFD_CROS_EC and that config option
already selects CROS_EC_PROTO, there is no need to make them explicitly
depend on CROS_EC_PROTO since that dependency is already met.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a cell for the usb power_supply part of the axp20x PMICs.
Note that this cell is only for the usb power_supply part and not the
ac-power / battery-charger / rtc-backup-bat-charger bits.
Depending on the board each of those must be enabled / disabled separately
in devicetree as most boards do not use all 4. So in dt each one needs its
own child-node of the axp20x node. Another reason for using separate child
nodes for each is so that other devicetree nodes can have a power-supply
property with a phandle referencing a node representing a single
power-supply.
The decision to use a separate devicetree node for each is reflected on
the kernel side by each getting its own mfd-cell / platform_device and
platform-driver.
Note this commit also makes some whitespace changes to the intialization
of existing cells in axp20x_cells, these are pure whitespace changes,
functionally nothing changes.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add an extra set of registers which is necessary tu support the PMICs
battery charger function, and mark registers which contain status bits,
gpio status, and adc readings as volatile.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Clear out a few checkpatch warnings and white space errors.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we use the dev_get_platdata, pdata can be NULL in DT environments.
Actually, NULL pointer exception is occurs with error messages like this:
[ 1.226583] Unable to handle kernel NULL pointer dereference at virtual address 00000044
[ 1.467910] [<c02f1e38>] (wm8994_irq_init) from [<c02f1bd4>] (wm8994_i2c_probe+0x684/0x858)
[ 1.476241] [<c02f1bd4>] (wm8994_i2c_probe) from [<c0371c78>] (i2c_device_probe+0x11c/0x17c)
In wm8994-core, we already checked whether platform data is NULL and set the
wm8994->pdata to platform data if platform data is not NULL.
So, we can use wm8994->pdata instead of platform data.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Implement .irq_set_wake() to get who is wakeup source and setup on suspend/reumse. Enable
mt6393_irq as wake up source properly to pinctrl by enable_irq_wake()/enable_irq_wake().
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the compatible strings for the at91sam9x5, at91sam9n12, sama5d4 and
sama5d2 SoCs.
Update the documentation accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver support for a OnKey component
- MFD core adds the resource da9062_onkey_resources[] for the OnKey
- An appropriate value has been added into mfd_cell da9062_devs[] to
support component .name = "da9062-onkey" and
.of_compatible = "dlg,da9062-onkey"
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's pretty silly to do
irq_data *d = irq_get_irq_data(irq_data->irq);
because that results in d = irq_data, but goes through a lookup of the
irq_data. Use irq_data directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
irq is incremented for no value in the for loop. Remove it.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Do the same change to avoid the pattern "irq_get_chip_data(data->irq)".
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signal that this is a built-in driver and call its probe function
immediately on init. Suppress binding attributes and delete the
.remove() function since it is never unloaded. Tag probe() and
functions only called from probe() with __init. Delete all module
macros since this is a pure built-in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a special function for debug prints rather than the
usual hexdump function, let's use it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Clean out a misspelled "HW" (MW) and remove commented-out
codeline.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver support for a RTC component
- MFD core adds the RTC resources da9062_rtc_resources[] for the RTC
alarm and tick timer IRQ
- An appropriate mfd_cell has been added into da9062_devs[] to support
a component .name = "da9062-rtc" and .of_compatible = "dlg,da9062-rtc"
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Explicitly set the regmap endianness instead of relying on
the default being correct.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Implement irq_chip->irq_get_irqchip_state to make it possible for PMIC
block drivers to access the IRQ real time status bits. The status bits
are used for various kinds of input signals, e.g. GPIO.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some HLCDC registers cannot be written until the hardware has finished
applying the previous configuration request. If they are written while
an action is still in progress, the new configuration might be silently
ignored, resulting in unpredictable behavior.
Hide the config synchronization stuff in a regmap implementation and use
this implementation instead of the generic mmio one.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a missing DVC_RDY interrupt mask in struct regmap_irq definition.
The original submission of this driver did not contain all interrupt
masking definitions in the struct regmap_irq contained in the file
da9063-irq.c
The solution is to add a DA9063_IRQ_DVC_RDY entry to enum da9063_irqs
list and to add the corresponding values to compensate for the missing
mask bit in the static const struct regmap_irq da9063_irqs[] table.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp152 is a stripped down version of the axp202 pmic with the battery
charging function removed as it is intended for top-set boxes.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-bBL6 and COME-cBW6
boards to the Kontron PLD driver. The list of supported products in the
module description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Qualcomm Debug Subsystem clock is used by CoreSight components.
Add required definitions for it. qcom_rpm_resource::status_id is
not used by driver, so just mark it as ~0.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap register definitions have been a source of many small fixes
as issues are discovered. As such I made a small automated tool to
check these definitions. This patch fixes the issues (mostly harmless)
located by that tool, the issues fall into three catagories:
1) Volatile registers that have a default in the defaults table (default
has been removed from the table since it is redundant)
2) Registers that are marked as volatile but unreadable (register has
been removed from the volatile list since it is obviously not being
used)
3) Registers that arn't readable but have an entry in the defaults
table (again removed since it is redundant)
4) Readable non-volatile registers that are missing a default, these are
dangerous as they won't get synced during a cache sync. Fortunately,
most of them seem to be registers that shouldn't be there (for example
wm5102 had readable registers for DRC2 and ISRC3 which is doesn't have)
Hopefully another tool will be produced to check the actual default
values themselves but that is outside the scope of this patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
o Making pdata NULL check to (!pdata) as coding standard
and all other checks in file.
o Removing redundant check of pdata, because we already
check for pdata, and also derefernced before this check.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.
Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function arizona_irq_thread (the threaded handler for the arizona
IRQs) calls pm_runtime_get_sync at the start to ensure that the chip is
active as we handle the IRQ. If the chip is part way through a runtime
suspend when an IRQ arrives the PM core will wait for the suspend to
complete, before resuming. However, since commit 4f0216409f7c
("mfd: arizona: Add better support for system suspend") the runtime
suspend function may call disable_irq, if the chip is going to fully
power off, which will try to wait for any outstanding IRQs to complete.
This results in deadlock as the IRQ thread is waiting for the PM
operation to complete and the PM thread is waiting for the IRQ to
complete.
To avoid this situation we use disable_irq_nosync, which allows the
suspending thread to finish the suspend without waiting for the IRQ to
complete. This is safe because if an IRQ is being processed it can only
be blocked at the pm_runtime_get_sync at the start of the handler
otherwise it wouldn't be possible to suspend.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Sunrisepoint (Skylake PCH) has the iTCO watchdog accessible across
the SMBus, unlike previous generations of PCH/ICH where it was on the
LPC bus. Because it's on the SMBus, it doesn't make sense to pass around
a 'struct lpc_ich_info', and leaking the type of bus into the iTCO
watchdog driver is kind of backwards anyway.
This change introduces a new 'struct itco_wdt_platform_data' for use
inside the iTCO watchdog driver and by the upcoming Intel Sunrisepoint
code, which neatly avoids having to include lpc_ich headers in the i801
i2c driver.
This change is overdue because lpc_ich_info has already found its way
into other TCO watchdog users, notably the intel_pmc_ipc driver where
the watchdog actually isn't on the LPC bus as far as I can see.
A simple translation layer is provided for converting from the existing
'struct lpc_ich_info' inside the lpc_ich mfd driver.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com> [drivers/x86 refactoring]
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Fix runtime PM issues on Arizona
- Fix IRQ/Suspend race on Arizona
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/Rnq
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- fix dependency issues on ChromeOS platforms
- fix runtime PM issues on Arizona
- fix IRQ/suspend race on Arizona
* tag 'mfd-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: Remove MFD_CROS_EC_SPI depends on OF
platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM
mfd: arizona: Fix initialisation of the PM runtime
mfd: arizona: Fix race between runtime suspend and IRQs
The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.
commit ab37813f40
twl4030_charger: Allow charger to control the regulator that feeds it
gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.
Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.
So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The new coming Intel platforms such as Skylake will contain Sunrisepoint PCH.
The main difference to the previous platforms is that the LPSS devices are
compound devices where usually main (SPI, HSUART, or I2C) and DMA IPs are
present.
This patch brings the driver for such devices found on Sunrisepoint PCH.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newly introduced device_for_each_child_reverse() would be used when MFD
core removes the device.
After this patch applied the devices will be removed in a reversed order. This
behaviour is useful when devices have implicit dependency on order, i.e.
consider MFD device with serial bus controller, such as SPI, and DMA IP that is
attached to serial bus controller: before remove the DMA driver we have to be
ensured that no DMA transfers is ongoing and the requested channel are unused.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC SPI transport driver has a dependency on OF because it
uses some OF helpers from the <linux/of.h> header. But there isn't a
need for an explicit dependency since the header has stub functions if
CONFIG_OF is not defined.
Also, MFD_CROS_EC_SPI already depends on MFD_CROS_EC which in turn has
a dependency on OF so in practice can't be selected without CONFIG_OF.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PM runtime core by default assumes a chip is suspended when runtime
PM is enabled. Currently the arizona driver enables runtime PM when the
chip is fully active and then disables the DCVDD regulator at the end of
arizona_dev_init. This however has several problems, firstly the if we
reach the end of arizona_dev_init, we did not properly follow all the
proceedures for shutting down the chip, and most notably we never marked
the chip as cache only so any writes occurring between then and the next
PM runtime resume will be lost. Secondly, if we are already resumed when
we reach the end of dev_init, then at best we get unbalanced regulator
enable/disables at work we lose DCVDD whilst we need it.
Additionally, since the commit 4f0216409f7c ("mfd: arizona: Add better
support for system suspend"), the PM runtime operations may
disable/enable the IRQ, so the IRQs must now be enabled before we call
any PM operations.
This patch adds a call to pm_runtime_set_active to inform the PM core
that the device is starting up active and moves the PM enabling to
around the IRQ initialisation to avoid any PM callbacks happening until
the IRQs are initialised.
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The function arizona_irq_thread (the threaded handler for the arizona
IRQs) calls pm_runtime_get_sync at the start to ensure that the chip is
active as we handle the IRQ. If the chip is part way through a runtime
suspend when an IRQ arrives the PM core will wait for the suspend to
complete, before resuming. However, since commit 4f0216409f7c
("mfd: arizona: Add better support for system suspend") the runtime
suspend function may call disable_irq, if the chip is going to fully
power off, which will try to wait for any outstanding IRQs to complete.
This results in deadlock as the IRQ thread is waiting for the PM
operation to complete and the PM thread is waiting for the IRQ to
complete.
To avoid this situation we use disable_irq_nosync, which allows the
suspending thread to finish the suspend without waiting for the IRQ to
complete. This is safe because if an IRQ is being processed it can only
be blocked at the pm_runtime_get_sync at the start of the handler
otherwise it wouldn't be possible to suspend.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is needed as the CRC PMIC has support for Panel
enable/diable as gpio which needs 'gpiod_add_lookup_table'
and 'gpiod_remove_lookup_table' from gpiolib. This patch
can be squashed with below commit in topic/crc-pmic branch
commit 61dd2ca2d4
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Fri Jun 26 14:32:05 2015 +0530
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO
signal
On some Intel SoC platforms, the panel enable/disable signals
are controlled by CRC PMIC. Add those control as a new GPIO in a
lookup table for gpio-crystalcove chip during CRC driver load
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On some BYT PLatform the PWM is controlled using CRC PMIC. Add a lookup
entry for the same to be used by the consumer (Intel GFX)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed for PWM control suuported by the PMIC
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On some Intel SoC platforms, the panel enable/disable signals are
controlled by CRC PMIC. Add those control as a new GPIO in a lookup
table for gpio-crystalcove chip during CRC driver load
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJVqUFGAAoJECTWi3JdVIfQ3YUH+LWLxVerlyUj/uug4vhRLlp2
KkKLInX1r9Al8cRWo6ln3kdB8jTmOxFxm1XUkpz+IQLiF0yV5kGtVm7uBup/X4DA
5oi7313rPs4maS/jqwyuOUi8X+ZMkKxp1Pgf4dJAzRJPN5tlks3drYdqY2c7JdT0
q5IqUR1KIsouK1/wCBy17BEe9PLpjV6U/yN2E/b1tsW1utjtAgY5pPjv/MZpPJ8C
NI6WXHjdykIi6Peg1mHqczgGEkyRlKBllZVsOvFhX1yjy0ITvao5/Mpv8NK5BwwU
cOWPVLlXOwa4m+kVXePPgA4GlB2q1Xupw5k6TDPip5aCGUgS+ryKQmOVcNaJnA==
=C5/o
-----END PGP SIGNATURE-----
Merge tag 'regmap-seq-delay-api' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-wm5110
regmap: Create a new struct reg_sequence for register sequences
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the same definition of state container as in MAX77693 drivers.
This will allow usage of one regulator driver in both devices: MAX77693
and MAX77843.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a register patch for rev E and above that configures the location of
some write sequences to assist with the headphone enables.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This register will be needed as part of some additional support for the
headphone path on wm5110, so this patch adds the register and sets up
its regmap config.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Provide MT6397 RTC interrupt, base address, and register in
MT6397 MFD.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- plug a potential race related to chained interrupt handlers
- core updates which address the needs of the x86 irqdomain conversion
- new irqchip callback to support affinity settings for VCPUs
- the usual pile of updates to interrupt chip drivers
- a few helper functions to allow further cleanups and
simplifications
I have a largish pile of coccinelle scripted/verified cleanups and
simplifications pending on top of that, but I prefer to send that
towards the end of the merge window when the arch/driver changes have
hit your tree to avoid API change wreckage as far as possible"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
genirq: Remove bogus restriction in irq_move_mask_irq()
irqchip: atmel-aic5: Add sama5d2 support
irq: spear-shirq: Fix race in installing chained IRQ handler
irq: irq-keystone: Fix race in installing chained IRQ handler
gpio: gpio-tegra: Fix race in installing chained IRQ handler
gpio: gpio-mxs: Fix race in installing chained IRQ handler
gpio: gpio-mxc: Fix race in installing chained IRQ handler
ARM: gemini: Fix race in installing GPIO chained IRQ handler
GPU: ipu: Fix race in installing IPU chained IRQ handler
ARM: sa1100: convert SA11x0 related code to use new chained handler helper
irq: Add irq_set_chained_handler_and_data()
irqchip: exynos-combiner: Save IRQ enable set on suspend
genirq: Introduce helper function irq_data_get_affinity_mask()
genirq: Introduce helper function irq_data_get_node()
genirq: Introduce struct irq_common_data to host shared irq data
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
irqchip: gic: Simplify gic_configure_irq by using IRQCHIP_SET_TYPE_MASKED
irqchip: renesas: intc-irqpin: Improve binding documentation
genirq: Set IRQCHIP_SKIP_SET_WAKE for no_irq_chip
...
Using -1 as platform device id means that the platform driver core will not
assign any id to the device (the device name will not have id at all). This
results problems on systems that have multiple PCHs (Platform Controller
HUBs) because all of them also include their own copy of LPC device.
All the subsequent device creations will fail because there already exists
platform device with the same name.
Fix this by passing PLATFORM_DEVID_AUTO as platform device id. This makes
the platform device core to allocate new ids automatically.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD support for the DA9063 OnKey driver
The function da9063_clear_fault_log() is added to mitigate the case of a
hardware power-cut after a long-long OnKey press. Although there is no
software intervention in this case (by definition) such a shutdown would
cause persistent information within the DA9063 FAULT_LOG that would be
available during the next device restart.
Clearance of this persistent register must be completed after such a
hardware power-cut operation has happened so that the FAULT_LOG does not
continue with previous values. The clearance function has been added here
in the kernel driver because wiping the fault-log cannot be counted on
outside the Linux kernel.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
[Lee: Removed 'key_power' for Dmitry to take through the Input Tree]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The use of ifneq against 'n' to conditionally compile codec-specific
parts is wrong and was resulting in all the codec tables being built
even for deselected codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Current code in mfd-core calls into ACPI to check resources even
on a system that booted with a DT (on kernels with both DT and ACPI
support compiled in). This triggers ACPI exceptions since we may
end up calling the ACPI interpreter when it has not been initialized:
"ACPI Exception: AE_BAD_PARAMETER, Thread 2064154624 could not acquire
Mutex [0x1] (20150410/utmutex-285)"
This patch fixes the issues by adding a check for an ACPI companion
device before carrying out ACPI resources checks to avoid calling
the ACPI interpreter if the fwnode representing the device is an OF one.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Later arizona silicon has the single/differential selector
in a different register, and IN1_MODE only selects between
analogue or digital. Prepare for this by splitting the
INx_MODE definition into two fields.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the wm5110 it is important the reset line is held for slightly longer
to ensure the device starts up well. This patch adds a 5mS delay for
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The low power sleep mode on wm5110 requires that the LDO1 regulator be
set to 1.175V prior to entering sleep, then returned to 1.2V after
exiting sleep mode. This patch apply these regulator settings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some register settings must be applied before the first time low power
sleep mode is entered on the wm5110 to ensure optimium performance.
These settings require SYSCLK to be enabled whilst they are being
applied. This patch applies the settings using the recently factored out
boot time SYSCLK functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
wm5102 applies a custom hardware boot sequence, for this the SYSCLK
needs to be enabled. This patch factors out the code that enables
SYSCLK for this sequence such that it can be used for other boot time
operations that require SYSCLK.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation for some refactoring fixup some minor style, formating
and code clarity issues.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The wm5102 uses a custom boot sequence and the standard boot sequence is
disabled. However, the standard boot sequence must be run at least once
after a cold boot (caused by either a hard reset or removal of AVDD).
Unfortunately the register WRITE_SEQUENCER_CTRL_3 is not affected by the
hardware reset. This means if the device has been previously booted but
the AVDD supply has never been removed, arizona_dev_init will reset the
chip but the boot sequence will not run, which can cause numerous
problems. The solution is to manually clear this register and then boot
the chip again, which is what this patch does.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds functions for enabling and disabling the physical reset
line. This will be helpful in future refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This also handily fixes a leak of the GPIO in arizona_dev_exit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I noticed the PMIC configuration on 37xx-evm won't actually shut down
the voltages during off-idle. Turns out 37xx-evm needs the AC charger
state transitions disabled like we are doing for SDP and LDP in the
legacy booting case.
Let's fix this for device tree based booting by setting up the quirk
flag based on the compatible flag. And let's also use the existing
define for STARTON_CHG.
Note that SDP and EVM do not have the PMIC clken wired to gate the
the oscillator while LDP has.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This soft reset used to be located after the register patch had been
applied, but has since moved to before the patch is applied. At the new
location there is no requirement to do a register sync as no register
writes will have happened yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify in various drivers configuration data which is not modified:
- regmap_irq_chip,
- individual regmap_irq's in array,
- regmap_config,
- irq_domain_ops,
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert SA11x0 (Neponset, SA1111, and UCB1x00 code) to use the new
irq_set_chained_handler_and_data() helper.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4yzx-0002S6-7p@rmk-PC.arm.linux.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some ECs need a little time for waking up before they can accept
SPI data at a high speed. This is configurable via a DT property
"google,cros-ec-spi-pre-delay".
This patch makes the cros_ec_spi driver to cause a delay before
the beginning of a SPI transaction, to make sure that the EC has
already woken up, if the property has been defined in the DTS.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.
Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.
Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add proto v3 support to the SPI, I2C, and LPC.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support in cros_ec.c to handle EC host command protocol v3.
For v3+, probe for maximum shared protocol version and max
request, response, and passthrough sizes. For now, this will
always fall back to v2, since there is no bus-specific code
for handling proto v3 packets.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the EC device tree node has sub-nodes, try to instantiate them as
MFD sub-devices. We can configure the EC features provided by the board.
Signed-off-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Parent and device were pointing to the same device structure.
Parent is unused, removed.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix broken probe of da9052 regulators, which since commit b3f6c73db7
("mfd: da9052-core: Fix platform-device id collision") use a
non-deterministic platform-device id to retrieve static regulator
information. Fortunately, adequate error handling was in place so probe
would simply fail with an error message.
Update the mfd-cell ids to be zero-based and use those to identify the
cells when probing the regulator devices.
Fixes: b3f6c73db7 ("mfd: da9052-core: Fix platform-device id collision")
Cc: stable <stable@vger.kernel.org> # v3.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now that the axp20x-regulators driver supports different variants of the
AXP family, we can enable regulator support for AXP22X without the risk
of incorrectly configuring regulators.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the AXP22x PMIC devices to the existing AXP20x driver.
This includes the AXP221 and AXP223, which are identical except for
the external data bus. Only AXP221 is added for now. AXP223 will be
added after it's Reduced Serial Bus (RSB) interface is supported.
AXP22x defines a new set of registers, power supplies and regulators,
but most of the API is similar to the AXP20x ones.
A new irq chip definition is used, even though the available interrupts
on AXP22x is a subset of those on AXP20x. This is done so the interrupt
numbers match those on the datasheet.
This patch only enables the interrupts, system power-off function, and PEK
sub-device. The regulator driver must first support different variants
before we enable it from the mfd driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[wens@csie.org: fix interrupts and move regulators to separate patch]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
* new API for safe access of power supply function attrs
* devres support for power supply (un)registration
* new drivers / chips
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
* twl4030-madc-battery: convert to iio consumer
* misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbZu
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1' of git://git.infradead.org/battery-2.6
Pull power supply and reset changes from Sebastian Reichel:
- new API for safe access of power supply function attrs
- devres support for power supply (un)registration
- new drivers / chips:
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
- twl4030-madc-battery: convert to iio consumer
- misc fixes
* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
power: twl4030_madc_battery: Add missing MODULE_ALIAS
power: twl4030-madc-battery: Convert to iio consumer.
dt: power: Add docs for generic SYSCON poweroff driver.
power: reset: Add generic SYSCON register mapped poweroff.
power: max17042_battery: add missed blank
power: max17042_battery: Use reg type instead of chip type
power/reset: at91: big endian fixes for atsama5d3x
power_supply: charger-manager: Fix dereferencing of ERR_PTR
HID: input: Fix NULL pointer dereference when power_supply_register fails
power: constify of_device_id array
power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
arm: mach-pxa: Decrement the power supply's device reference counter
mfd: ab8500: Decrement the power supply's device reference counter
power_supply: bq2415x_charger: Decrement the power supply's device reference counter
power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
x86/olpc/xo15/sci: Use newly added power_supply_put API
x86/olpc/xo1/sci: Use newly added power_supply_put API
power_supply: charger-manager: Decrement the power supply's device reference counter
power_supply: Increment power supply use counter when obtaining references
...
The RTC on S2MPS11 is the same as S2MPS14. However interrupt numbers of
RTC alarms 0 and 1 were inversed between these two devices. So when
rtc-s5m driver requested S2MPS14_IRQ_RTCA0 interrupt, it matched to
S2MPS11_IRQ_RTCA1, not RTCA0.
Fix this by using consistent RTC alarm interrupt numbers and adding a
BUILD_BUG_ON for future generations.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The earpiece on 5102 is mono, thus there is no output 3R. Remove the
registers associated with the unused right channel from the readable
registers list.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the mfd cell info for axp288 extcon device.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The patch sorts IDs in the table for easier maintenance. There is no
functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded "platform:twl6040" modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some of the PMIC's could have specific regmap configuration
tables in future, so add specific compatible strings for known
PMIC's. Also print runtime detected chip revision information.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace duplicated const keyword for 'axp20x_model_names' with proper
array of const pointers to const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Drop support for SW controlled VCORE, nobody uses it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch just sorts IDs in the table for better maintenance. There is no
functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The IPQ8064 also includes an RPM following the same message structure as
other chips. In addition, it supports a few new resource types to
support the NSS fabric clocks and the SMB208/SMB209 regulators found on
the reference boards.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 6e3f62f079 ("mfd: core: Fix platform-device id
generation") we honour PLATFORM_DEVID_AUTO and PLATFORM_DEVID_NONE when
registering mfd-devices.
Unfortunately, some mfd-drivers rely on the old behaviour of generating
platform-device ids by adding the cell id also to the special value of
PLATFORM_DEVID_NONE. The resulting platform ids are not only used to
generate device-unique names, but are also used instead of the cell id
to identify cells when probing subdevices.
These drivers should be updated to use PLATFORM_DEVID_AUTO, which would
also allow more than one device to be registered without resorting to
hacks (see for example wm831x), but lets fix the regression first by
partially reverting the above mentioned commit with respect to
PLATFORM_DEVID_NONE.
Fixes: 6e3f62f079 ("mfd: core: Fix platform-device id generation")
Cc: stable <stable@vger.kernel.org> # v3.19
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
dmi_get_system_info() may return NULL either when CONFIG_DMI is not set or when
board has an old firmware. The patch prevents a crash and changes the default
frequency to be in align with older board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Lee: Removed overt "sentinel" comment and extra lines]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS11 PMIC (present on Arndale Octa board) has the same RTC module
as S2MPS14 device. Add respective mfd cell to enable it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API consolidation only and
should make things more readable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use %pS for actual addresses, otherwise you'll get bad output
on arches like ppc64 where %pF expects a function descriptor.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use power_supply_put() to decrement the power supply's device reference
counter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Replace direct calls to power supply function attributes with wrappers.
Wrappers provide safe access in case of unregistering the power
supply (e.g. by removing the driver). Replace:
- get_property -> power_supply_get_property
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On success, callback function returns 0. So invert the if condition
check so that we can break out of loop.
Cc: stable@vger.kernel.org
Signed-off-by: Ameya Palande <2ameya@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a DT binding that lets the DMIC reference voltage source be
specified for each input.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change flash cell identifiers from max77693-flash to max77693-led
to avoid confusion with NOR/NAND Flash.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In Quark X1000, there's a single PCI device that provides both
an I2C controller and a GPIO controller. This MFD driver will
split the 2 devices for their respective drivers.
This patch is based on Josef Ahmad's initial work for Quark enabling.
Acked-by: Michael Turquette <mturquette@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rk808 has a under voltage detect function, when the voltage of buck is
under 85% the target voltage, the buck output will reset. But if the
power load is too heavy, this function maybe err, when current over
4.2A, although the voltage is normal, but RK808 mistakenly think it is
under 85%, and reset the buck. So let's disable this function.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 0b2712585(linux-next.git) this driver uses regmap_irq and so needs
to select REGMAP_IRQ.
This fixes the following compilation errors:
ERROR: "regmap_irq_get_domain" [drivers/mfd/rt5033.ko] undefined!
ERROR: "regmap_add_irq_chip" [drivers/mfd/rt5033.ko] undefined!
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The range of registers used by this driver exceeds that available
via SPI with no paging (127), so we have to override the values
from the default config which is set-up for I2C access.
Also change SPI settings to match device's recommended OTP values.
Signed-off-by: Adam Ward <adam.ward.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds MAX77843 core/irq driver to support PMIC,
MUIC(Micro USB Interface Controller), Charger, Fuel Gauge,
LED and Haptic device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds support for the MediaTek MT6397 PMIC. This is a
multifunction device with the following sub modules:
- Regulator
- RTC
- Audio codec
- GPIO
- Clock
It is interfaced to the host controller using SPI interface by a proprietary
hardware called PMIC wrapper or pwrap. MT6397 MFD is a child device of the
pwrap.
Signed-off-by: Flora Fu, MediaTek
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is no need to print additional ENOMEM message for
sec_platform_data allocation failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The WTSR (Watchdog Timer Software Reset) and SMPL (Sudden Momentary
Power Loss) were removed from rtc-s5m driver because they were not used.
Remove them (and on/off interrupt) from main MFD driver and header.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
pcr_dbg is a wrapper of dev_dbg, which can save some code,
and help to enable/disable debug message static.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To enable/disable ASPM we should find LINK CONTROL register
in PCI config space. All old chip use 0x80 address, but new
chip may use another address, so we using pci_find_capability()
to get LINK CONTROL address.
rtsx_gops.c was removed, we consider to put some common operations
to this file, but the actual thing is, only a group of chips
are in common ops1, and another group of chips in common ops2,
it is hard to decide put which ops into generic ops file.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update some phy register name and value for rts5249,
the updated value makes chip more stable on some platform.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
update card drive settings, This setting can be used for rts5249
rts524A and rts525A.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
PETXCFG is defined at 0xFF03, the old 0xFE49 not used any more.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In one shot mode, sequencer automatically disables all enabled steps at
the end of each cycle. (both ADC steps and TSC steps) Hence these steps
need not be saved in reg_se_cache for clearing these steps at a later
stage.
Also, when ADC wakes up Sequencer should not be busy executing any of the
config steps except for the charge step. Previously charge step was 1 ADC
clock cycle and hence it was ignored.
TSC steps are always disabled at the end of each conversion cycle, hence
there is no need to explicitly disable TSC steps by writing 0 to REG_SE.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now, as all VE platforms have to be booted with DT,
the code handling non-DT case can be removed.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-cBL6 board to
the Kontron PLD driver. The list of supported products in the module
description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Name changes to the battery cell structure to a
more generic cell type: fuel gauge.
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Surely GPIO irq will be used as an input pin so make sure its direction is
set after requesting.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is usually better to pass actual error code from a function call than
mangling it to another.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
intel_soc_pmic_find_gpio_irq() tries to find a GPIO interrupt but doesn't
select between it or I2C interrupt so it makes more sense to move this
comment to intel_soc_pmic_i2c_probe() with minor edits.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ChromeOS EC character device is an user-space interface to
allow applications to access the Embedded Controller.
Add a cell for this device so it's spawned from the mfd driver.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The struct cros_ec_command will be used as an ioctl() argument for the
API to control the ChromeOS EC from user-space. So the data structure
has to be 64-bit safe to make it compatible between 32 and 64 avoiding
the need for a compat ioctl interface. Since pointers are self-aligned
to different byte boundaries, use fixed size arrays instead of pointers
for transferring ingoing and outgoing data with the Embedded Controller.
Also, re-arrange struct members by decreasing alignment requirements to
reduce the needing padding size.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the Wolfson Microelectronics WM8280 and WM8281
codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
[Lee: Minor fixup to remove potentially uninitialised variable. ]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch add a missing check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A card insertion happens after the lastest polling before reader is
suspended may never have a chance to be detected. Under current 1-HZ
polling interval setting in mmc_core, the worst case of such
undetectablility is about 1 second.
To further reduce the undetectability, detect card slot again in suspend
method and defer the autosuspend if the slot is loaded. The default 2
second autosuspend delay of USB subsystem should let the next polling
detects the card.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add device tree support for DA9063 regulators; Real-Time Clock
and Watchdog.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver for the Resource Power Manager (RPM) found in Qualcomm 8660, 8960
and 8064 based devices. The driver exposes resources that child drivers
can operate on; to implementing regulator, clock and bus frequency
drivers.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver is used only on Exynos based boards with DTS support.
After removal of board file support from max77686 and max77802 regulator
drivers, the MFD driver can be converted to DTS-only version. This
simplifies a little the code:
1. No dead (unused) entries in platform_data structure.
2. More code removed.
3. Regulator driver does not depend on allocated memory
from MFD driver.
4. It makes also easier extending the regulator driver.
Add to the max77686 MFD driver dependency on CONFIG_OF because without
DTS the regulator drivers (max77686 and max77802) won't bind.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Removes some functions that are not used anywhere:
usbhs_readb() usbhs_writeb()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make array of
struct reg_default const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make array of
struct reg_default const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
After commit: 6e3f62f079 ("mfd: core: Fix platform-device id generation")
We must set the id base when register a duplicate name of mfd_cell.
If not, duplicate filename error was reported.
- sysfs: cannot create duplicate filename '/devices/.../wm8994-ldo'
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Without suspend/resume functionality in the USB driver the USB core
will disconnect and reconnect the DLN2 port and because the GPIO
framework does not yet support removal of an in-use controller a
suspend/resume operation will result in a crash.
This patch provides suspend and resume functions for the DLN2 driver
so that the above scenario is avoided, if the host controller does not
drop VBUS during suspend, since in this case the device state is
preserved.
We chose not implemented reset_resume so that if the host controller
does drop VBUS the resume path will go through above the
disconnect/reconnect process since it is probably better to fix the
GPIO framework disconnect issue then to save and restore the device
state for every driver.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is in preparation for adding suspend / resume support.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Quark X1000 uses ie6xx_wdt driver for WDT. To enable WDT, we declare WDT IO
resource size for Quark X1000.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DA9150 is a combined Charger and Fuel-Gauge IC, with additional
GPIO and GPADC functionality.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the function prcmu_get_boot_status() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the ir-clk which is part of the sun6i SoC prcm module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a new driver for Richtek RT5033 driver.
RT5033 is a Multifunction device which includes battery charger, fuel gauge,
flash LED current source, LDO and synchronous Buck converter. It is interfaced
to host controller using I2C interface.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Skip caching volatile registers in tps65218
- Use correct address base in tps65218
- Repair deadlock on suspend in rtsx_usb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Afdx
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- Avoid platform ID collision in da9052
- Skip caching volatile registers in tps65218
- Use correct address base in tps65218
- Repair deadlock on suspend in rtsx_usb
* tag 'mfd-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: rtsx_usb: Fix runtime PM deadlock
mfd: tps65218: Make INT1 our status_base register
mfd: tps65218: Make INT[12] and STATUS registers volatile
mfd: da9052-core: Fix platform-device id collision
sd_set_power_mode() in derived module drivers/mmc/host/rtsx_usb_sdmmc.c
acquires dev_mutex and then calls pm_runtime_get_sync() to make sure the
device is awake while initializing a newly inserted card. Once it is
called during suspending state and explicitly before rtsx_usb_suspend()
acquires the same dev_mutex, both routine deadlock and further hang the
driver because pm_runtime_get_sync() waits the pending PM operations.
Fix this by using an empty suspend method. mmc_core always turns the
LED off after a request is done and thus it is ok to remove the only
rtsx_usb_turn_off_led() here.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: 730876be25 ("mfd: Add realtek USB card reader driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
[Lee: Removed newly unused variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we don't tell regmap-irq that our first status
register is at offset 1, it will try to read offset
zero, which is the chipid register.
Fixes: 44b4dc6 mfd: tps65218: Add driver for the TPS65218 PMIC
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STATUS register can be modified by the HW, so we
should bypass cache because of that.
In the case of INT[12] registers, they are the ones
that actually clear the IRQ source at the time they
are read. If we rely on the cache for them, we will
never be able to clear the interrupt, which will cause
our IRQ line to be disabled due to IRQ throttling.
Fixes: 44b4dc6 mfd: tps65218: Add driver for the TPS65218 PMIC
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow multiple DA9052 regulators be registered by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.
The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when multiple regulators
are registered:
[ 0.128855] da9052-regulator da9052-regulator: invalid regulator ID specified
[ 0.128973] da9052-regulator: probe of da9052-regulator failed with error -22
[ 0.129148] ------------[ cut here ]------------
[ 0.129200] WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x5c/0x7c()
[ 0.129233] sysfs: cannot create duplicate filename '/devices/platform/soc/60000000.aips/63fc8000.i2c/i2c-0/0-0048/da9052-regulator
...
[ 0.132891] ------------[ cut here ]------------
[ 0.132924] WARNING: CPU: 0 PID: 1 at lib/kobject.c:240 kobject_add_internal+0x24c/0x2cc()
[ 0.132957] kobject_add_internal failed for da9052-regulator with -EEXIST, don't try to register things with the same name in the same directory.
...
[ 0.137000] da9052 0-0048: mfd_add_devices failed: -17
[ 0.138486] da9052: probe of 0-0048 failed with error -17
Based on the fix done by Johan Hovold at commit b668422872 ("mfd:
viperboard: Fix platform-device id collision").
Tested on a imx53-qsb board, where multiple DA9053 regulators can be
successfully probed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mfd/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
The MFD_ATMEL_HLCDC was first intended to be selected by its sub-devices
but these sub-devices now depends on this option, we thus need to add
a name and a description so that users can see it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Baytrail-T-CR platform firmware has defined two customized operation
regions for PMIC chip Dollar Cove XPower - one is for power resource
handling and one is for thermal just like the CrystalCove one. This patch
adds support for them on top of the common PMIC opregion region code.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Baytrail-T platform firmware has defined two customized operation
regions for PMIC chip Crystal Cove - one is for power resource handling
and one is for thermal: sensor temperature reporting, trip point setting,
etc. This patch adds support for them on top of the existing Crystal Cove
PMIC driver.
The reason to split code into a separate file intel_pmic.c is that there
are more PMIC drivers with ACPI operation region support coming and we can
re-use those code. The intel_pmic_opregion_data structure is created also
for this purpose: when we need to support a new PMIC's operation region,
we just need to fill those callbacks and the two register mapping tables.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After registering mfd device with proper irq_base
platform_get_irq_byname() calls will return VIRQ instead of local IRQ.
This fixes da9063 rtc registration issue:
da9063-rtc da9063-rtc: Failed to request ALARM IRQ 1: -22
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix a typo in name of company in copyright comment.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the extra 4 channels were added to AIF2 the necessary frame control
registers were not given defaults and marked readable. This patch fixes
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
