Setting memdump state to idle prior to setting of callback function
pointer for command timeout to NULL,causing the issue.Now moved the
initialisation of memdump state to qca_setup().
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1.During SSR for command time out if BT SoC goes to inresponsive
state, power cycling of BT SoC was not happening. Given the fix by
sending hw error event to reset the BT SoC.
2.If SSR is triggered then ignore the transmit data requests to
BT SoC until SSR is completed.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tx pending flag is set to true when HOST IBS state is AWAKE or
AWAKEING. If IBS state is ASLEEP, then Tx clock is already voted
off. To optimize further directly calling serial_clock_vote()
instead of qca_wq_serial_tx_clock_vote_off(), at this point of
qca_suspend() already data is sent out. No need to wake up hci to
send data.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some version of WCN399x, SoC idle timeout is configured
as 80ms instead of 20ms or 40ms. To honor all the SoC's
supported in the driver increasing SoC idle timeout to 200ms.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Due to race conditions between qca_hw_error and qca_controller_memdump
during SSR timeout,the same pointer is freed twice. This results in a
double free. Now a lock is acquired before checking the stauts of SSR
state.
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If waiting for IBS sleep times out jump to the error handler, this is
easier to read than multiple 'if' branches and a fall through to the
error handler.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_suspend() calls serdev_device_wait_until_sent() regardless of
whether a transfer is pending. While it does no active harm since
the function should return immediately it makes the code more
confusing. Add a flag to track whether a transfer is pending and
only call serdev_device_wait_until_sent() is needed.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_suspend() removes the vote for the UART TX clock after
writing an IBS sleep request to the serial buffer. This is
not a good idea since there is no guarantee that the request
has been sent at this point. Instead remove the vote after
successfully entering IBS sleep. This also fixes the issue
of the vote being removed in case of an aborted suspend due
to a failure of entering IBS sleep.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The serial clocks should be on when there is a vote for at least one
of the clocks (RX or TX), and off when there is no 'on' vote. The
current logic to determine the combined state is a bit redundant
in the code paths for different types of votes, use a single
statement in the common path instead.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a function like devm_clk_get_optional() function returns both error
pointers on error and NULL then the NULL return means that the optional
feature is deliberately disabled. It is a special sort of success and
should not trigger an error message. The surrounding code should be
written to check for NULL and not crash.
On the other hand, if we encounter an error, then the probe from should
clean up and return a failure.
In this code, if devm_clk_get_optional() returns an error pointer then
the kernel will crash inside the call to:
clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ);
The error handling must be updated to prevent that.
Fixes: 77131dfec6 ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA6390 memdump VSE sometimes come to bluetooth driver
with wrong sequence number as illustrated as follows:
frame # in dec: frame data in hex
1396: ff fd 01 08 74 05 00 37 8f 14
1397: ff fd 01 08 75 05 00 ff bf 38
1414: ff fd 01 08 86 05 00 fb 5e 4b
1399: ff fd 01 08 77 05 00 f3 44 0a
1400: ff fd 01 08 78 05 00 ca f7 41
it is mistook for controller missing packets, so results
in page fault after overwriting memdump buffer allocated.
Fixed by ignoring QCA6390 sequence number check and
checking buffer space before writing.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Warm reboot can not reset controller qca6390 due to
lack of controllable power supply, so causes firmware
download failure during enable.
Fixed by sending VSC EDL_SOC_RESET to reset qca6390
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
@dev parameter of qca_suspend()/qca_resume() represents
serdev_device, but it is mistook for hci_dev and causes
succedent unexpected memory access.
Fix by taking @dev as serdev_device.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hdev is always allocated and not only when power control is required.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN3991 supports transparent WBS (host encoded mSBC). Add a flag to the
device match data to show WBS is supported.
This requires the matching firmware for WCN3991 in linux-firmware:
1a8b0dc00f77 (qca: Enable transparent WBS for WCN3991)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move the read of max-speed from device-tree out of the qca_is_wcn399x
if block so oper_speed can be set for QCA9377 devices as well.
Suggested-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a compatible so QCA9377 devices can be defined in device-tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for QCA6390, including the devicetree and acpi
compatible hwid matching, and patch/nvm downloading.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces devm_gpiod_get() with devm_gpiod_get_optional() to get
bt_en and replaces devm_clk_get() with devm_clk_get_optional() to get
susclk. It also uses NULL check to determine whether the resource is
available or not.
Fixes: 8a208b24d7 ("Bluetooth: hci_qca: Make bt_en and susclk not mandatory for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some platforms the bt_en pin and susclk are default on and there
is no exposed resource to control them. This patch makes the bt_en
and susclk not mandatory to have BT work. It also will not set the
HCI_QUIRK_NON_PERSISTENT_SETUP and shutdown() callback if bt_en is
not available.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA Rome doesn't support the pre-shutdown vendor hci command, this patch
will check the soc type in qca_power_off() and only send this command
for wcn399x.
Fixes: ae563183b6 ("Bluetooth: hci_qca: Enable power off/on support during hci down/up for QCA Rome")
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will fix the below issues
1. Discarding memory dump events if memdump state is moved to
MEMDUMP_TIMEOUT.
2. Fixed race conditions between qca_hw_error() and qca_controller_memdump
while free memory dump buffers using mutex lock
3. Moved timeout timer to delayed work queue
4. Injecting HW error event in a case when dumps failed to receive and HW
error event is not yet received.
5. Clearing hw error and command timeout function callbacks before
sending pre shutdown command.
Collecting memory dump will follow any of the below sequence.
Sequence 1:
Receiving Memory dump events from the controller
Received entire dump in stipulated time
Received HW error event from the controller
Controller Reset from HOST
Sequence 2:
Receiving Memory dump events from the controller
Failed to Receive entire dump in stipulated time
A Timeout schedules and if no HW error event received a fake HW
error event will be injected.
Controller Reset from HOST.
Sequence 3:
Received HW error event
HOST trigger SSR by sending crash packet to controller.
Received entire dump in stipulated time
Controller Reset from HOST
Fixes: d841502c79 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Reported-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Directly passing clock pointer to clock code without checking for NULL
as clock code takes care of it
* Removed the comment which was not necessary
* Updated code for return in qca_regulator_enable()
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of relying on other subsytem to turn ON clocks
required for BT SoC to operate, voting them from the driver.
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch registers hdev->shutdown() callback and also sets
HCI_QUIRK_NON_PERSISTENT_SETUP for QCA Rome. It will power-off the BT chip
during hci down and power-on/initialize the chip again during hci up. As
wcn399x already enabled this, this patch also removed the callback register
and QUIRK setting in qca_setup() for wcn399x and uniformly do this in the
probe() routine.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the retry of btsoc initialization when it fails. There are
reports that the btsoc initialization may fail on some platforms but the
repro ratio is very low. The symptoms is the firmware downloading failed
due to the UART write timed out. The failure may be caused by UART,
platform HW or the btsoc itself but it's very difficlut to root cause,
given the repro ratio is very low. Add a retry for the btsoc initialization
can work around most of the failures and make Bluetooth finally works.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Current qca_power_shutdown() only supports wcn399x, this patch adds Rome
power off support to it. For Rome it just needs to pull down the bt_en
GPIO to power off it. This patch also replaces all the power off operation
in qca_close() with the unified qca_power_shutdown() call.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a unified API qca_power_on() to support both wcn399x and
Rome power on. For wcn399x it calls the qca_wcn3990_init() to init the
regulators, and for Rome it pulls up the bt_en GPIO to power up the btsoc.
It also moves all the power up operation from hdev->open() to
hdev->setup().
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/bluetooth/hci_qca.c: In function 'qca_controller_memdump':
drivers/bluetooth/hci_qca.c:980:6: warning:
variable 'opcode' set but not used [-Wunused-but-set-variable]
It is never used since commit d841502c79 ("Bluetooth: hci_qca: Collect
controller memory dump during SSR"), so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We will collect the ramdump of BT controller when hardware error event
received before rebooting the HCI layer. Before restarting a subsystem
or a process running on a subsystem, it is often required to request
either a subsystem or a process to perform proper cache dump and
software failure reason into a memory buffer which application
processor can retrieve afterwards. SW developers can often provide
initial investigation by looking into that debugging information.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace of_device_get_match_data with device_get_match_data to make driver
work across platforms.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add support for WCN3991 i.e. current values and fw download
support.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add PM suspend/resume callbacks for hci_qca driver.
BT host will make sure both Rx and Tx go into sleep state in
qca_suspend. Without this, Tx may still remain in awake state, which
prevents BTSOC from entering deep sleep. For example, BlueZ will send
Set Event Mask to device when suspending and this will wake the device
Rx up. However, the Tx idle timeout on the host side is 2000 ms. If the
host is suspended before its Tx idle times out, it won't send
HCI_IBS_SLEEP_IND to the device and the device Rx will remain awake.
We implement this by canceling relevant work in workqueue, sending
HCI_IBS_SLEEP_IND to the device and then waiting HCI_IBS_SLEEP_IND sent
by the device.
In order to prevent the device from being awaken again after qca_suspend
is called, we introduce QCA_SUSPEND flag. QCA_SUSPEND is set in the
beginning of qca_suspend to indicate system is suspending and that we'd
like to ignore any further wake events.
With QCA_SUSPEND and spinlock, we can avoid race condition, e.g. if
qca_enqueue acquires qca->hci_ibs_lock before qca_suspend calls
cancel_work_sync and then qca_enqueue adds a new qca->ws_awake_device
work after the previous one is cancelled.
If BTSOC wants to wake the whole system up after qca_suspend is called,
it will keep sending HCI_IBS_WAKE_IND and uart driver will take care of
waking the system. For example, uart driver will reconfigure its Rx pin
to a normal GPIO pin and enable irq wake on that pin when suspending.
Once host detects Rx falling, the system will begin resuming. Then, the
BT host clears QCA_SUSPEND flag in qca_resume and begins dealing with
normal HCI packets. By doing so, only a few HCI_IBS_WAKE_IND packets are
lost and there is no data packet loss.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit cde9dde6e1.
The frame reassembly errors were root caused to a transient gpio issue.
The missing response was root caused to an issue with properly managing
RFR in the uart driver. Addressing those root causes occurs outside of
hci_qca and eliminates the need for the 50ms delay, so remove it.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Split and rename qca_power_setup() in order to simplify each code path
and to clarify that it is unrelated to qca_power_off() and
qca_power_setup().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the regulator_set_load() and regulator_set_voltage() out of the
enable/disable code paths the code can now use the standard
regulator bulk enable/disable API.
By cloning num_vregs into struct qca_power there's no need to lug around
a reference to the struct qca_vreg_data, which further simplifies
qca_power_setup().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices with specific voltage requirements should not request voltage
from the driver, but instead rely on the system configuration to define
appropriate voltages for each rail.
This ensures that PMIC and board variations are accounted for, something
that the 0.1V range in the hci_qca driver currently tries to address.
But on the Lenovo Yoga C630 (with wcn3990) vddch0 is 3.1V, which means
the driver will fail to set the voltage.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the introduction of '5451781dadf8 ("regulator: core: Only count
load for enabled consumers")' in v5.0, the requested load of a regulator
consumer is only accounted for when said consumer is voted enabled.
So there's no need to vote for load ever time the regulator is
enabled or disabled.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On the msm8998 mtp, the response to the baudrate change command is never
received. On the Lenovo Miix 630, the response to the baudrate change
command is corrupted - "Frame reassembly failed (-84)".
Adding a 50ms delay before re-enabling flow to receive the baudrate change
command response from the wcn3990 addesses both issues, and allows
bluetooth to become functional.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When SoC receives pre shut down command, it share the same
with other COEX shared clients. So SoC needs a short time
after sending VS pre shutdown command before turning off
the regulators and sending the power off pulse. Along with
short delay, needs to wait for command complete event for
Pre shutdown VS command
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA UART Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Static structure qca_proto, of type hci_uart_proto, is used four times:
as the last argument in function hci_uart_register_device(), and as the
only argument to functions hci_uart_register_proto() and
hci_uart_unregister_proto(). In all three of these functions, the
parameter corresponding to qca_proto is declared as constant. Therefore,
make qca_proto itself constant as well in order to protect it from
unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The qca_data structure is allocated with kzalloc() and hence
zero-initialized. Remove a bunch of unnecessary explicit
initializations of struct members to zero.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Looks like Deadlock is observed in hci_qca while performing
stress and stability tests. Since same lock is getting
acquired from qca_wq_awake_rx and hci_ibs_tx_idle_timeout
seeing spinlock recursion, irqs should be disable while
acquiring the spinlock always.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't fall through to print error message when receive sleep indication
in HCI_IBS_RX_ASLEEP state, this is allowed behavior.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN399x chips are coex chips, it needs a VS pre shutdown
command while turning off the BT. So that chip can inform
BT is OFF to other active clients.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
