NPIV re-enable code was blocked after FW had been initialized. The
blocking check was too broad. Reduce the check to make sure if FW is
initialized or not.
Link: https://lore.kernel.org/r/20200226224022.24518-14-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
RPD information failed to display by switch cli command. This is
caused by driver failure to properly format RDP response data with
data descriptor to allow switch to parse it correctly.
Link: https://lore.kernel.org/r/20200226224022.24518-13-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For single port 28XX adapter, the second core can still run in the
background. The flash semaphore can be held by the non-active core.
This patch tell MPI FW to check for this case and clear the semaphore
from the non-active core.
Link: https://lore.kernel.org/r/20200226224022.24518-12-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per FW request, MB 1-7 should be logged for 8002 error.
Link: https://lore.kernel.org/r/20200226224022.24518-11-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit e4e3a2ce95 ("scsi: qla2xxx: Add ability to autodetect SFP
type") takes a heavy handed approach to BPM (Buffer Plus Management)
enablement:
1) During hardware initialization, if an LR-capable transceiver is
recognized, the driver schedules a disruptive post-initialization
chip-reset (ISP-ABORT) to allow the BPM settings to be sent to the
firmware. This chip-reset will result in (short-term) path-loss to
all fc-rports and their attached SCSI devices.
2) LR-detection is triggered during any link-up event, resulting in a
refresh and potential chip-reset
Based on firmware-team guidance, upon LR-capable transceiver
recognition, the driver's hardware initialization code will now
re-execute firmware with the new BPM settings, then continue on with
driver initialization. To address the second issue, the driver
performs LR-capable detection upon the driver receiving a
transceiver-insertion asynchronous event from firmware. No short-term
path loss is needed with this new semantic.
Link: https://lore.kernel.org/r/20200226224022.24518-10-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue where current and original exchanges count
were swapped for intiator and targets.
Also fix IOCB count for current and original which were swapped.
Link: https://lore.kernel.org/r/20200226224022.24518-9-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There's no point checking flags.disable_msix_handshake in the
interrupt handler hot-path. Instead perform the check during
queue-pair instantiation and use the proper interrupt handler.
Link: https://lore.kernel.org/r/20200226224022.24518-8-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Andrew Vasquez <andrewv@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch ensures flash updates API calls return possible failure
status through BSG interface to the application.
Link: https://lore.kernel.org/r/20200226224022.24518-7-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improved message for Secure Flash support. No
functionality has been changed.
Link: https://lore.kernel.org/r/20200226224022.24518-6-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue where incorrect flag was used for sending
switch commands.
Link: https://lore.kernel.org/r/20200226224022.24518-5-hmadhani@marvell.com
Fixes: e8c72ba51a ("[SCSI] qla2xxx: Use GFF_ID to check FCP-SCSI FC4 type before logging into Nx_Ports")
Fixes: a4239945b8 ("scsi: qla2xxx: Add switch command to simplify fabric discovery")
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch uses generic firmware update options for FCoE based
adapters as well to reduce code duplication.
Link: https://lore.kernel.org/r/20200226224022.24518-4-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch moves ql2xrdpenable check earlier to avoids setting
fw_option once again before exiting qla24xx_update_fw_options.
Link: https://lore.kernel.org/r/20200226224022.24518-3-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allows sparse to verify the endianness of the arguments passed
to make_handle().
Link: https://lore.kernel.org/r/20200220043441.20504-5-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following sparse warnings:
drivers/scsi/qla2xxx/qla_mbx.c:120:21: warning: restricted pci_channel_state_t degrades to integer
drivers/scsi/qla2xxx/qla_mbx.c:120:37: warning: restricted pci_channel_state_t degrades to integer
>From include/linux/pci.h:
enum pci_channel_state {
/* I/O channel is in normal state */
pci_channel_io_normal = (__force pci_channel_state_t) 1,
/* I/O to channel is blocked */
pci_channel_io_frozen = (__force pci_channel_state_t) 2,
/* PCI card is dead */
pci_channel_io_perm_failure = (__force pci_channel_state_t) 3,
};
Link: https://lore.kernel.org/r/20200220043441.20504-4-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of changing endianness in-place, write the data in CPU endian
format in another buffer and copy that buffer back. This patch does not
change any functionality but silences some sparse endianness warnings.
Link: https://lore.kernel.org/r/20200220043441.20504-3-bvanassche@acm.org
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the SCSI core does not reuse the tag of the SCSI command that is
being aborted by .eh_abort() before .eh_abort() has finished it is not
necessary to check from inside that callback whether or not the SCSI
command has already completed. Instead, rely on the firmware to return an
error code when attempting to abort a command that has already
completed. Additionally, rely on the firmware to return an error code when
attempting to abort an already aborted command.
In qla2x00_abort_srb(), use blk_mq_request_started() instead of
sp->completed and sp->aborted.
Link: https://lore.kernel.org/r/20200220043441.20504-2-bvanassche@acm.org
Cc: Martin Wilck <mwilck@suse.com>
Cc: Quinn Tran <qutran@marvell.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes:
- qla2x00_issue_iocb_timeout will now return if chip is down
- only check for sp->qpair in abort handling
Link: https://lore.kernel.org/r/20200212214436.25532-24-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ISP28xx, use 28xx call to retrieve active FW region.
Link: https://lore.kernel.org/r/20200212214436.25532-21-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add port name in the messages file to help debugging of Login/Logout IOCBs
Link: https://lore.kernel.org/r/20200212214436.25532-20-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ths patch fixes MBX in-direction for setting right bits for
qla2x00_echo_test()
Link: https://lore.kernel.org/r/20200212214436.25532-19-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fixes loopback and echo test options.
Link: https://lore.kernel.org/r/20200212214436.25532-18-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This takes care of big endian architectures.
Link: https://lore.kernel.org/r/20200212214436.25532-17-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes RDP length in case when driver needs to reduce length of
RDP response
Link: https://lore.kernel.org/r/20200212214436.25532-16-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch reduces RDP response payload length, if requesting port is a
domain controller (sid 0xfffc01) and fw is earlier than 8.09.00 and fw is
not 8.05.65 then limit the RDP response payload length to maximum of 256
bytes by terminating the response just before the optical element
descriptor.
Link: https://lore.kernel.org/r/20200212214436.25532-15-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds deferred queue for processing aborts and RDP in the driver.
Link: https://lore.kernel.org/r/20200212214436.25532-14-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does the following to improve RDP processing:
- Rename field port_id to d_id in ELS and PUREX iocb structs to match FW
spec.
- Remove redundant comments from ELS and PUREX iocb structs.
- Refactor fields in ELS iocb struct for error subcode common access.
- Properly use error subcode fields in rdp processing routine.
- Add print logs for alloc failure in purex rdp processing routine.
Link: https://lore.kernel.org/r/20200212214436.25532-13-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch correctly displays port speed capability and current speed for
RDP command.
Link: https://lore.kernel.org/r/20200212214436.25532-12-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During Link up phase and Data rate MBX command response, print message
indicating FCE is enabled.
Link: https://lore.kernel.org/r/20200212214436.25532-11-hmadhani@marvell.com
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for extended FDMI commands and cleans up code to
reduce duplication.
Link: https://lore.kernel.org/r/20200212214436.25532-10-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides separate module parameter ql2xrdpenable to turn on/off
RDP capability in the driver. However, if ql2xsmartsan parameter is
enabled, it will also turn on ql2xfdmienable parameter since it is required
for RDP to work.
Link: https://lore.kernel.org/r/20200212214436.25532-9-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds RDP command support in the driver. With the help of new
ql2xsmartsan parameter, driver will use PUREX IOCB mode to send RDP command
to switch and will be able to receive various diagnostic data.
Link: https://lore.kernel.org/r/20200212214436.25532-8-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prepares code for implementing Vendor specific extended FDMI/RDP
commands. It also addes support for MBC_GET_PORT_DATABASE and
MBC_GET_RNID_PARAMS commands.
Link: https://lore.kernel.org/r/20200212214436.25532-7-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes endian warning for fc_host_stats.
Link: https://lore.kernel.org/r/20200212214436.25532-6-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds sysfs node to show D-Port diag data.
Link: https://lore.kernel.org/r/20200212214436.25532-4-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch moves freeing of fcport out of interrupt context.
Link: https://lore.kernel.org/r/20200212214436.25532-3-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides an interface to do the following (using MBC 0x3B):
- Displays (in hex) the LED config words for all three LEDs.
- Programs the config words for one LED or for all three LEDs.
The sysfs node defined is named beacon_config.
First, to allow driver to gain LED control, do this:
# echo 1 > /sys/class/scsi_host/host#/beacon
Then, to display config words for all three LEDs do this:
# cat /sys/class/scsi_host/host#/beacon_config
To set config words for all three LEDs do this:
# echo 3 xxxx yyyy zzzz > /sys/class/scsi_host/host#/beacon_config
Or, to set config word for a specific single LED n do this:
# echo n xxxx > /sys/class/scsi_host/host#/beacon_config
where n is the LED number (0, 1, 2)
Finally, to restore LED control back to firmware, do this:
# echo 0 > /sys/class/scsi_host/host#/beacon
Link: https://lore.kernel.org/r/20200212214436.25532-2-hmadhani@marvell.com
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Document the locking assumptions this function relies on and also verify
these locking assumptions at runtime.
Cc: Quinn Tran <qutran@marvell.com>
Cc: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/r/20200123042345.23886-2-bvanassche@acm.org
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce code duplication by introducing the tcm_qla2xxx_{get,rel}_cmd()
functions. Introduce these functions in the tcm_qla2xxx.c source files such
that the qla_target.c source file becomes independent of the SCSI target
core header files. This patch fixes a bug, namely by ensuring that
qlt_alloc_qfull_cmd() sets cmd->se_cmd.map_tag.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Link: https://lore.kernel.org/r/20200103192719.205158-1-bvanassche@acm.org
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Five small patches, all in drivers or doc, which missed the initial
pull request. The qla2xxx and megaraid_sas are actual fixes and the
rest are spelling and doc changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXj8MoCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUjlAQChB8+I
pBKVOfU+38vndu+YW6IRb11HhxKzY9LlHVf04wD+LxKsxuYKpZjivytfuYJGsxMD
C5EWLUxB7GYUQItEBjQ=
=7xJj
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI fixes from James Bottomley:
"Five small patches, all in drivers or doc, which missed the initial
pull request.
The qla2xxx and megaraid_sas are actual fixes and the rest are
spelling and doc changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: fix spelling mistake "initilized" -> "initialized"
scsi: pm80xx: fix spelling mistake "to" -> "too"
scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
scsi: megaraid_sas: fixup MSIx interrupt setup during resume
scsi: qla2xxx: Fix unbound NVME response length
On certain cases when response length is less than 32, NVME response data
is supplied inline in IOCB. This is indicated by some combination of state
flags. There was an instance when a high, and incorrect, response length
was indicated causing driver to overrun buffers. Fix this by checking and
limiting the response payload length.
Fixes: 7401bc18d1 ("scsi: qla2xxx: Add FC-NVMe command handling")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200124045014.23554-1-hmadhani@marvell.com
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2d Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas. There
are a couple of core and base updates around error propagation and
atomicity in the attribute container base we use for the SCSI
transport classes. The rest is minor changes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXjHQJyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZZ8AQC02N+v
iUnTl1YxGPjIWBbnHuUxN2Qbb9D3C6gAT1LkigEArlk163K3A1XEQHF/VNCdAz/f
01XYTd3p1VHuegIBHlk=
=Cn52
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2d Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas.
There are a couple of core and base updates around error propagation
and atomicity in the attribute container base we use for the SCSI
transport classes.
The rest is minor changes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (149 commits)
scsi: hisi_sas: Rename hisi_sas_cq.pci_irq_mask
scsi: hisi_sas: Add prints for v3 hw interrupt converge and automatic affinity
scsi: hisi_sas: Modify the file permissions of trigger_dump to write only
scsi: hisi_sas: Replace magic number when handle channel interrupt
scsi: hisi_sas: replace spin_lock_irqsave/spin_unlock_restore with spin_lock/spin_unlock
scsi: hisi_sas: use threaded irq to process CQ interrupts
scsi: ufs: Use UFS device indicated maximum LU number
scsi: ufs: Add max_lu_supported in struct ufs_dev_info
scsi: ufs: Delete is_init_prefetch from struct ufs_hba
scsi: ufs: Inline two functions into their callers
scsi: ufs: Move ufshcd_get_max_pwr_mode() to ufshcd_device_params_init()
scsi: ufs: Split ufshcd_probe_hba() based on its called flow
scsi: ufs: Delete struct ufs_dev_desc
scsi: ufs: Fix ufshcd_probe_hba() reture value in case ufshcd_scsi_add_wlus() fails
scsi: ufs-mediatek: enable low-power mode for hibern8 state
scsi: ufs: export some functions for vendor usage
scsi: ufs-mediatek: add dbg_register_dump implementation
scsi: qla2xxx: Fix a NULL pointer dereference in an error path
scsi: qla1280: Make checking for 64bit support consistent
scsi: megaraid_sas: Update driver version to 07.713.01.00-rc1
...
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This patch improves readability and does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Link: https://lore.kernel.org/r/20191219005050.40193-1-bvanassche@acm.org
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
