According to patch "drm/i915/aml: Introducing Amber Lake platform"
(e364672477). Add a new marco for AML ULX GT2 devices.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538034499-31256-1-git-send-email-shawn.c.lee@intel.com
Sprite enable on ILK-IVB may take two frames to complete
when the hardware is in big FIFO mode (LP1+). That is
not entirely great as it means the sprite enable may
actually happen one frame after we've already signalled
flip completion. At the very least crc checks may fail
due to the sprite not yet being visible when we expect it.
We already have code to deal with big FIFO mode when it
comes to the sprite scaling on IVB
(WaCxSRDisabledForSpriteScaling:ivb). Let's extend that
workaround to kick in whenever the sprite is in the process
of being enabled. Also ILK/SNB bspec has some notes to
indicate that we should most likely also do the sprite
scaling w/a on all three platforms, so let's do that as well.
Pretty easy to reproduce on SNB/IVB. ILK has proved more
elusive, but let's trust the spec and include it as well.
v2: Make sure the pipe is active before the vblank wait
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Testcase: igt/kms_plane/pixel-format-pipe-*-planes
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107749
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20181004121527.30249-1-ville.syrjala@linux.intel.com
Fixing chv_set_phy_signal_level() still requires too many levels of
indirection to pass crtc_state along, but chv_data_lane_soft_reset()
already has a crtc_state we can use.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-13-maarten.lankhorst@linux.intel.com
fbdev init shouldn't race with userspace since it's called from
intel_modeset_init, so it's safe to dereference crtc->state and
assume nothing changed yet.
At least not more harmful than crtc->config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-11-maarten.lankhorst@linux.intel.com
Do not rely on crtc->config any more. Remove the assertion from
ibx_pch_dpll_disable, because we the dpll state tracking should
already handle this case correctly.
Changes since v1:
- Fixup accidental early return in intel_prepare_shared_dpll, oops!
Changes since v2:
- Don't use the freed crtc_state in intel_crtc_disable_noatomic()
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005095244.1324-1-maarten.lankhorst@linux.intel.com
Instead of passing crtc and dereferencing crtc->config,
passs the correct crtc_state and obtain the crtc pointer from there.
Changes since v1:
- Move vlv/chv changes and i9xx_set_pll_dividers changes
from crtc_enable/disable patches to here.
- Add commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-7-maarten.lankhorst@linux.intel.com
One more user of crtc->config down. :)
Changes since v1:
- Constify crtc_state
- int pipe -> enum pipe pipe
- Move i9xx_set_pipeconf declaration to the other pipeconf declarations.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004094604.2646-2-maarten.lankhorst@linux.intel.com
Earlier, we reasoned that having idled the gpu under mempressure, that
would be a good time to trim our request slabs in order to perform the
next request allocation. We have stopped performing the global operation
on the device (no idling) and wish to make the allocation failure
handling more local, so out with the global barrier that may take a long
time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005080300.9908-2-chris@chris-wilson.co.uk
Before we can reset the seqno, we have to be sure the engines are idle.
In debugfs/i915_drop_caches_set, we do wait_for_idle but allow ourselves
to be interrupted. We should only proceed to reset the seqno then if we
were not interrupted, and so also avoid overwriting the error status.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108133
Fixes: 6b048706f4 ("drm/i915: Forcibly flush unwanted requests in drop-caches")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004082119.24970-1-chris@chris-wilson.co.uk
Print the plane hw state readout results in the common format
we already use for pipes and encoders. Also print some clearer
debug messages when we disable planes during the early phases
of state readout/sanitization.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003145052.4633-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we decide that a plane is attached to the wrong pipe we try
to turn off said plane. However we are passing around the crtc we
think that the plane is supposed to be using rather than the crtc
it is currently using. That doesn't work all that well because
we may have to do vblank waits etc. and the other pipe might
not even be enabled here. So let's pass the plane's current crtc to
intel_plane_disable_noatomic() so that it can its job correctly.
To do that semi-cleanly we also have to change the plane readout
to record the plane's visibility into the bitmasks of the crtc
where the plane is currently enabled rather than to the crtc
we want to use for the plane.
One caveat here is that our active_planes bitmask will get confused
if both planes are enabled on the same pipe. Fortunately we can use
plane_mask to reconstruct active_planes sufficiently since
plane_mask still has the same meaning (is the plane visible?)
during readout. We also have to do the same during the initial
plane readout as the second plane could clear the active_planes
bit the first plane had already set.
v2: Rely on fixup_active_planes() to populate active_planes fully (Daniel)
Add Daniel's proposed comment to better document why we do this
Drop the redundant intel_set_plane_visible() call
Cc: stable@vger.kernel.org # fcba862e8428 drm/i915: Have plane->get_hw_state() return the current pipe
Cc: stable@vger.kernel.org
Cc: Dennis <dennis.nezic@utoronto.ca>
Cc: Daniel Vetter <daniel@ffwll.ch>
Tested-by: Dennis <dennis.nezic@utoronto.ca>
Tested-by: Peter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637
Fixes: b1e01595a6 ("drm/i915: Redo plane sanitation during readout")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003145017.4527-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print out the information whether the port and sink can each
do MST. And let's include the modparam in the debug output as well.
Makes life a little less confusing when you don't have to wonder
why MST isn't kicking in.
This does cause a slight change in our behaviour towards the sink.
Previously we only read the MSTM_CAP register after passing all
the other checks. Now we will read that register regardless. Hopefully
some crazy sink doesn't get confused by a simple register read.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003184210.1306-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
If the HW has not processed the db invalidation request yet, clearing
the cookie can generate a db ring. We clear the cookie when we
(re-)allocate the doorbell so no need to do it on destroy as well as no
one is going to look at it while the doorbell is inactive
v2: fix typo in patch title (Michal)
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002215430.15049-2-daniele.ceraolospurio@intel.com
GuC stores some data in there, which might be stale after a reset.
We already reset the WQ head and tail, but more things are being moved
to the descriptor with the interface updates. Instead of trying to track
them one by one, always memset and init the descriptors from scratch
after GuC is loaded.
The code is also reorganized so that the above operations and the
doorbell creation are grouped as "client enabling"
v2: add proc_desc_fini for symmetry (Daniele), remove unneeded var init,
add guc_is_alive() (Michal)
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002215430.15049-1-daniele.ceraolospurio@intel.com
Inside the execlists submission tasklet, we often make the mistake of
assuming that everything beneath the request is available for use.
However, the submission and the request live on two separate timelines,
and the request contents may be freed from an early retirement before we
have had a chance to run the submission tasklet (think ksoftirqd). To
safeguard ourselves against any mistakes, flush the tasklet before we
unpin the context if execlists still has a reference to this context.
v2: Pull hw_context->active tracking into schedule_in and schedule_out.
References: 60367132a2 ("drm/i915: Avoid use-after-free of ctx in request tracepoints")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003110941.27886-1-chris@chris-wilson.co.uk
We do not need to continually clear our dedicated PTE for error capture
as it will be updated and invalidated to the next object. Only at the
end do we wish to be sure that the PTE doesn't point back to any buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001194447.29910-3-chris@chris-wilson.co.uk
The final call to zlib_deflate(Z_FINISH) may require more output
space to be allocated and so needs to re-invoked. Failure to do so in
the current code leads to incomplete zlib streams (albeit intact due to
the use of Z_SYNC_FLUSH) resulting in the occasional short object
capture.
v2: Check against overrunning our pre-allocated page array
v3: Drop Z_SYNC_FLUSH entirely
Testcase: igt/i915-error-capture.js
Fixes: 0a97015d45 ("drm/i915: Compress GPU objects in error state")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003082422.23214-1-chris@chris-wilson.co.uk
We have new tests and fixes in place since the feature was last
disabled. Try again for gen-9+ hardware and enable only PSR1 by default as
a first step.
v2: Remove typo fix and comment improvements (Rodrigo)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
References: commit 2ee7dc497e ("drm/i915: disable PSR by default on HSW/BDW")
References: commit dcb2e993f3 ("Revert "drm/i915: Enable PSR by default on Valleyview and Cherryview."")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180928061117.12394-1-dhinakaran.pandiyan@intel.com
During driver load it's considered that the i915_driver_create()
function fails only in case of insufficient memory. Indeed, in
case of failure of i915_driver_create(), the load function
returns indiscriminately -ENOMEM ignoring the real cause of
failure.
In i915_driver_create() get the consistent error value from
drm_dev_init() and embed it in the pointer return value.
Signed-off-by: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002092047.14705-1-andi.shyti@intel.com
Previously we hesitated in adding the hw probe for the actual GPU
frequency for rps_boost as it is quite cumbersome, but given some
surprising HW behaviour it would be useful to know both the RPS boost
state and the actual HW state in one location.
v2: vlv/chv needs more tlc
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002113221.29208-1-chris@chris-wilson.co.uk
Add plane alpha blending support with the different blend modes.
This has been tested on a icl to show the correct results,
on earlier platforms small rounding errors cause issues. But this
already happens case with fully transparant or fully opaque RGB8888
fb's.
The recommended HW workaround is to disable alpha blending when the
plane alpha is 0 (transparant, hide plane) or 0xff (opaque, disable blending).
This is easy to implement on any platform, so just do that.
The tests for userspace are also available, and pass on gen11.
Changes since v1:
- Change mistaken < 0xff0 to 0xff00.
- Only set PLANE_KEYMSK_ALPHA_ENABLE when plane alpha < 0xff00, ignore blend mode.
- Rework disabling FBC when per pixel alpha is used.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Change MISSING_CASE default to explicit alpha disable (mattrope)]
Link: https://patchwork.freedesktop.org/patch/msgid/20180815103405.22679-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
As DMC Package contain DMC FW for multiple steppings including default
stepping. This patch will help to load FW for that particular stepping,
if FW for that stepping is available, instead of loading default FW.
v2 : Fix formatting issue.
Signed-off-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1536169347-31326-1-git-send-email-jyoti.r.yadav@intel.com
Latency is in the eye of the beholder. In the case where a client stops
and waits for the gpu, give that request chain a small priority boost
(not so that it overtakes higher priority clients, to preserve the
external ordering) so that ideally the wait completes earlier.
v2: Tvrtko recommends to keep the boost-from-user-stall as small as
possible and to allow new client flows to be preferred for interactivity
over stalls.
Testcase: igt/gem_sync/switch-default
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001144755.7978-3-chris@chris-wilson.co.uk
Currently, the backend scheduling code abuses struct_mutex into order to
have a global lock to manipulate a temporary list (without widespread
allocation) and to protect against list modifications. This is an
extraneous coupling to struct_mutex and further can not extend beyond
the local device.
Pull all the code that needs to be under the one true lock into
i915_scheduler.c, and make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001144755.7978-2-chris@chris-wilson.co.uk
Taken from an idea used for FQ_CODEL, we give the first request of a
new request flows a small priority boost. These flows are likely to
correspond with short, interactive tasks and so be more latency sensitive
than the longer free running queues. As soon as the client has more than
one request in the queue, further requests are not boosted and it settles
down into ordinary steady state behaviour. Such small kicks dramatically
help combat the starvation issue, by allowing each client the opportunity
to run even when the system is under heavy throughput load (within the
constraints of the user selected priority).
v2: Mark the preempted request as the start of a new flow, to prevent a
single client being continually gazumped by its peers.
Testcase: igt/benchmarks/rrul
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001144755.7978-1-chris@chris-wilson.co.uk
As we are about to allow ourselves to slightly bump the user priority
into a few different sublevels, packthose internal priority lists
into the same i915_priolist to keep the rbtree compact and avoid having
to allocate the default user priority even after the internal bumping.
The downside to having an requests[] rather than a node per active list,
is that we then have to walk over the empty higher priority lists. To
compensate, we track the active buckets and use a small bitmap to skip
over any inactive ones.
v2: Use MASK of internal levels to simplify our usage.
v3: Prevent overflow when SHIFT is zero.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123204.23982-4-chris@chris-wilson.co.uk
In the next few patches, we will want to give a small priority boost to
some requests/queues but not so much that we perturb the user controlled
order. As such we will shift the user priority bits higher leaving
ourselves a few low priority bits for our internal bumping.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123204.23982-3-chris@chris-wilson.co.uk
We've opted to use the maximum link rate and lane count for eDP panels,
because typically the maximum supported configuration reported by the
panel has matched the native resolution requirements of the panel, and
optimizing the link has lead to problems.
With eDP 1.4 rate select method and DSC features, this is decreasingly
the case. There's a need to optimize the link parameters. Moreover,
already eDP 1.3 states fast link with fewer lanes is preferred over the
wide and slow. (Wide and slow should still be more reliable for longer
cable lengths.)
Additionally, there have been reports of panels failing on arbitrary
link configurations, although arguably all configurations they claim to
support should work.
Optimize eDP 1.4+ link config fast and narrow.
Side note: The implementation has a near duplicate of the link config
function, with just the two inner for loops turned inside out. Perhaps
there'd be a way to make this, say, more table driven to reduce the
duplication, but seems like that would lead to duplication in the table
generation. We'll also have to see how the link config optimization for
DSC turns out.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105267
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905095321.13843-1-jani.nikula@intel.com
There are two copies of the same code called from long and short
pulse handlers.
v2: Rebase due to s/int status/enum drm_connector_status in
intel_dp_detect()
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-6-dhinakaran.pandiyan@intel.com
The intel_dp->detect_done flag is no more useful. Pull
intel_dp_long_pulse() into the lone caller,
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-5-dhinakaran.pandiyan@intel.com
A crtc modeset lock was added for link retraining but
intel_dp_retrain_link() knows to take the necessary locks since
commit c85d200e83 ("drm/i915: Move SST DP link retraining into the
->post_hotplug() hook")
v2: Drop AUX power domain reference in the early return path
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-4-dhinakaran.pandiyan@intel.com
We have two cases of intel_dp to intel_encoder conversions, use a
local variable to store the conversion.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-3-dhinakaran.pandiyan@intel.com
Commit '3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check,
unconditionally during long pulse"")' applies a work around for sinks
that don't signal link loss. The work around does not need to have to be
that broad as the issue was seen with only one particular monitor; limit
this only for external displays as eDP features like PSR turn off the link
and the driver ends up retraining the link seeeing that link is not
synchronized.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-2-dhinakaran.pandiyan@intel.com
Comment claims link needs to be retrained because the connected sink raised
a long pulse to indicate link loss. If the sink did so,
intel_dp_hotplug() would have handled link retraining. Looking at the
logs in Bugzilla referenced in commit '3cf71bc9904d ("drm/i915: Re-apply
Perform link quality check, unconditionally during long pulse"")', the
issue is that the sink does not trigger an interrupt. What we want is
->detect() from user space to check link status and retrain. Ville's
review for the original patch also indicates the same root cause. So,
rewrite the comment.
v2: Patch split and rewrote comment.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-1-dhinakaran.pandiyan@intel.com
If the request is currently on the HW (in port 0), then we do not need
to kick the submission tasklet to evaluate whether we should be
preempting itself in order to execute it again.
In the case that was annoying me:
execlists_schedule: rq(18:211173).prio=0 -> 2
need_preempt: last(18:211174).prio=0, queue.prio=2
We are bumping the priority of the first of a pair of requests running
in the current context. Then when evaluating preempt, we would see that
that our priority request is higher than the last executing request in
ELSP0 and so trigger preemption, not realising that our intended request
was already executing.
v2: As we assume state of the execlists->port[] that is only valid while
we hold the timeline lock we have to repeat some earlier tests that on
the validity of the node.
v3: Wrap guc submission under the timeline.lock as is now the way of all
things.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180925083205.2229-2-chris@chris-wilson.co.uk
