Trying to make au0828 to suspend can do very bad things, as
the polling Kthread is not handled. We should disable it
during suspend, only re-enabling it at resume.
Still, analog and digital TV won't work, as we don't reinit
the settings at resume, but at least it won't hang.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define au0828_rc_*() stubs to avoid compile errors when
VIDEO_AU0828_RC is disabled and avoid the need to enclose
au0828_rc_*() in ifdef CONFIG_VIDEO_AU0828_RC in .c files.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't make sense to handle an IR code given before
suspending after the device resume. So, turn off IR
int while suspending.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the RC kthread can re-enable IR int, we should first
cancel the kthread and then disable IR int.
While here, remove a temporary debug printk.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the DVB code sets the frontend, it disables the IR
INT, probably due to some hardware bug, as there's no code
there at au8522 frontend that writes on register 0xe0.
Fixing it at au8522 code is hard, as it doesn't know if the
IR is enabled or disabled, and just restoring the value of
register 0xe0 could cause other nasty effects. So, better
to add a hack at au0828-input polling interval to enable int,
if disabled.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The IR code increases the power consumption of the device.
Allow to disable it via modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This sleep was doing some debouncing on the original driver.
This is not needed on Linux, because the RC core and the input
layer already takes care of it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HVR-950Q uses an I2C remote controller at address 0x47 (7-bits
notation). Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commits 21dc61d3c0 and 7a1dd50b89 reduced the board I2C
speed to 20 MHz by default, due to a I2C stretch issue:
while xc5000 uses i2c stretch when a command is sent to it,
au0828 doesn't support this feature.
However, this is needed only for Xceive tuners. The other
I2C devices can work at the max speed.
So, revert the workarounds at board level, handling it at
I2C level, only when talking with xc5000.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While this device doesn't have a scaler (or have it disabled),
the screen dimentions are a function of the standard. Ok, right
now, only 480 lines standards are implemented, although it
supports other ones. Yet, let's calculate the size, to make
easier to add more standards latter.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It seems that there's a bug at au0828 hardware/firmware
related to alternate setting: when the device is already at
alt 5, a further call causes the URBs to receive -ESHUTDOWN.
I found two different encarnations of this issue:
1) at qv4l2, it fails the second time we try to open the
video screen;
2) at xawtv, when audio underrun occurs, with is very
frequent, at least on my test machine.
The fix is simple: just check if alt=5 before calling
set_usb_interface().
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The analog part of au0828 is missing the tuner Kconfig dependency.
That makes the device to not work while in analog mode.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Trevor, doing several opening/streaming/closing
operations to the demux causes it to fail.
I was able to simulate this bug too. I also noticed that,
sometimes, changing channels with au0828, the same thing
happens.
Most of the issues seem to be due to some hardware bug, that
causes the device to not fill all the URBs allocated. When
the bug happens, the only known fix is to either replug the
device, or to send an USB reset to it.
There's also a hack a the au0828 driver that starts a thread
that tries to reset the device when a package doesn't start
with a sync.
One of the culpits for this bad hardware behavior seem to be
caused by the lack of stopping and restarting the stream every
time a new channel is set.
This patch warrants that the stream will be properly reset
every time the set_frontend callback is called, partially
solving the problem.
A complete fix, however, would also need to check the PM
conditions for the tuner and demux.
Reported-by: Trevor Graffa <tlgraffa@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sometimes, it helps to know how much data was received by
urb_completion. Add that information to the optional debug
log.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the tuner is already disconnected, It is meaningless to go on doing the
stream-restart operation, It is better to cancel this operation.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.
Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Restructure the way we bring the various GPIOs out of reset. In particular:
1. we only need to setup the GPIOs as outputs once
2. there's no point in writing 0x40 to register 0x00 since that's the EEPROM
write protect and already it's configured as an input
3. Separate out the act of enabling the power supply and bringing the tuner
and demod out of reset. If you don't then the chip may not be properly
enabled (as the power supply is still ramping up when the chip comes
out of reset). This can result in probing failures.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following sparse warning:
drivers/media/usb/au0828/au0828-dvb.c:36:5: warning:
symbol 'preallocate_big_buffers' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added command line parameter preallocate_big_buffers so that the digital
transfer buffers can be allocated when the driver is registered. They
do not have to be allocated every time a feed is started.
Signed-off-by: Tim Mester <tmester@ieee.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Free what was allocated if there is a failure allocating
transfer buffers.
Stop the feed on a start feed error. The stop feed is not always called
if start feed fails. If the feed is not stopped on error, then the driver
will be stuck so that it can never start feeding again.
[m.chehab@samsung.com: CodingStyle cleanup]
Signed-off-by: Tim Mester <tmester@ieee.org>
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDIOC_DBG_G_CHIP_IDENT has been replaced by VIDIOC_DBG_G_CHIP_INFO. Remove
g_chip_ident support from bridge drivers since it is no longer needed.
This patch takes care of all the trivial cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- open/close/read and poll need to take the core lock as well.
- when the tuner goes to sleep we should set std_set_in_tuner_core
to 0 since the tuner loses the firmware at that time.
- initialize the tuner if std_set_in_tuner_core == 0 whenever:
1) g/s_tuner, s_std or s_frequency is called
2) read or poll is called
3) streamon is called
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After loading the module the initial video routing is not setup.
Explicitly call s_input to get this right.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just opening a device shouldn't have any side-effects.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Turn it into a simple function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver crashed when the device was disconnected while an application
still had a device node open. Fixed by using the release() callback of struct
v4l2_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also get rid of unnecessary format type check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- V4L2_CAP_AUDIO was set, but enumaudio was not implemented.
- audioset was never filled by enum_input
- ctrl_ainput was never updated when switching the video input
- g_audio was broken due to faulty logic: g_audio should set the
index, it doesn't receive it from the user.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- define an initial frequency
- return an error if g_frequency is called for an invalid tuner index
- get the clamped frequency value after setting it: i.e. the tuner driver
may clamp the given frequency to a valid frequency range and ctrl_freq
should get that actual clamped frequency.
- remove obsolete tuner type checks (done by the core).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers using wall clock time (CLOCK_REALTIME) to timestamp from the
monotonic timer (CLOCK_MONOTONIC).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull the analog frontend setup code out of au0828_card_setup into its
own seperate function, au0828_card_analog_fe_setup().
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the dependendency of VIDEO_AU0828 on VIDEO_V4L2 by
creating a new Kconfig option, VIDEO_AU0828_V4L2, which enables analog
video capture support and depends on VIDEO_V4L2 itself.
With VIDEO_AU0828_V4L2 disabled, the driver will only support digital
television and will not depend on the v4l2-core. With VIDEO_AU0828_V4L2
enabled, the driver will be built with the analog v4l2 support included.
By default, the VIDEO_AU0828_V4L2 option will be set to Y, so as to
preserve the original behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
