If CONFIG_GPIOLIB is disabled, fwnode_get_named_gpiod() becomes a stub
function, which return -ENOSYS. Handle this in the same way as
-ENOENT, i.e. assume there is no GPIO used to reset the PHYs.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet switch on the MDIO bus have historically performed their own
handling of the GPIO reset line. The resent patch to have the MDIO
core handle the reset has broken the switch drivers, in that they
cannot claim the GPIO. Some switch drivers need more control over the
GPIO line than what the MDIO core provides. So restore the historical
behaviour by only performing a reset of PHYs, not switches.
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that all mdio devices populate the struct device fwnode pointer
as well as the of_node pointer to allow drivers that wish to use
fwnode APIs to work.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY devices sometimes do have their reset signal (maybe even power
supply?) tied to some GPIO and sometimes it also does happen that a boot
loader does not leave it deasserted. So far this issue has been attacked
from (as I believe) a wrong angle: by teaching the MAC driver to manipulate
the GPIO in question; that solution, when applied to the device trees, led
to adding the PHY reset GPIO properties to the MAC device node, with one
exception: Cadence MACB driver which could handle the "reset-gpios" prop
in a PHY device subnode. I believe that the correct approach is to teach
the 'phylib' to get the MDIO device reset GPIO from the device tree node
corresponding to this device -- which this patch is doing...
Note that I had to modify the AT803x PHY driver as it would stop working
otherwise -- it made use of the reset GPIO for its own purposes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Propagate actual errors from fwnode_get_named_gpiod()]
[geert: Avoid destroying initial setup]
[geert: Consolidate GPIO descriptor acquiring code]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 95b80bf3db ("mdio_bus:
Remove unneeded gpiod NULL check"), this commit assumed that GPIOLIB
checks for NULL descriptors, so it's safe to drop them, but it is not
when CONFIG_GPIOLIB is disabled in the kernel. If we do call
gpiod_set_value_cansleep() on a GPIO descriptor we will issue warnings
coming from the inline stubs declared in include/linux/gpio/consumer.h.
Fixes: 95b80bf3db ("mdio_bus: Remove unneeded gpiod NULL check")
Reported-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO reset GPIO is really a classical optional GPIO property case,
so devm_gpiod_get_optional() should have been used, not devm_gpiod_get().
Doing this saves several LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact, still
burdening the kernel with now apparently useless loops -- get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use of_mdio_parse_addr() in place of an OF read of reg and a bounds
check (which is litterally the exact same thing that
of_mdio_parse_addr() does)
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-loading of the Marvell DSA driver has stopped working with recent
kernels. This seems to be due to the change of binding for DSA devices,
moving them from the platform bus to the MDIO bus.
In order for module auto-loading to work, we need to provide a MODALIAS
string in the uevent file for the device. However, the device core does
not automatically provide this, and needs each bus_type to implement a
uevent method to generate these strings. The MDIO bus does not provide
such a method, so no MODALIAS string is provided:
.# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
In the case of OF-based devices, the solution is easy -
of_device_uevent_modalias() does the work for us. After this is done,
the uevent file looks like this:
.# cat /sys/bus/mdio_bus/devices/f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
MODALIAS=of:NswitchT<NULL>Cmarvell,mv88e6085
which results in auto-loading of the Marvell DSA driver on Clearfog
platforms.
Fixes: c0405563a6 ("ARM: dts: armada-388-clearfog: Utilize new DSA binding")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API convention makes it that a given MDIO bus reset should be able
to access PHY devices in its reset() callback and perform additional
MDIO accesses in order to bring the bus and PHYs in a working state.
Commit 69226896ad ("mdio_bus: Issue GPIO RESET to PHYs.") broke that
contract by first calling bus->reset() and then release all PHYs from
reset using their shared GPIO line, so restore the expected
functionality here.
Fixes: 69226896ad ("mdio_bus: Issue GPIO RESET to PHYs.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:
- descend into drivers/net/phy/ unconditionally
- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
which allows us not to expose the internal MDIO board info list and
mutex, yet maintain the logic within the same file
- relocate the code that creates a MDIO device into
drivers/net/phy/mdio_bus.c
- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
defined (y or m)
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea01340 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new configuration symbol: MDIO_DEVICE which allows building
the MDIO devices and bus code, without pulling in the entire Ethernet
PHY library and devices code.
PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are
updated to reflect that.
When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we
have mdio-bus.ko as a loadable module, and it does not have a
module_exit() function because the safety of removing a bus class is
unclear.
When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble
everything into a common loadable module: libphy.ko because of nasty
circular dependencies between phy.c, phy_device.c and mdio_bus.c which
are really tough to untangle.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've finally noticed that mdiobus_scan() also returns either NULL or error
value on failure. Return ERR_PTR(-ENODEV) instead of NULL since this is
the error value already filtered out by the callers that want to ignore
the MDIO address scan failure...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b74766a0a0 ("phylib: don't return NULL
from get_phy_device()") in linux-next, phy_get_device() will return
ERR_PTR(-ENODEV) instead of NULL if the PHY device ID is all ones.
This causes problem with stmmac driver and likely some other drivers
which call mdiobus_register(). I triggered this bug on SoCFPGA MCVEVK
board with linux-next 20160427 and 20160428. In case of the stmmac, if
there is no PHY node specified in the DT for the stmmac block, the stmmac
driver ( drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c function
stmmac_mdio_register() ) will call mdiobus_register() , which will
register the MDIO bus and probe for the PHY.
The mdiobus_register() resp. __mdiobus_register() iterates over all of
the addresses on the MDIO bus and calls mdiobus_scan() for each of them,
which invokes get_phy_device(). Before the aforementioned patch, the
mdiobus_scan() would return NULL if no PHY was found on a given address
and mdiobus_register() would continue and try the next PHY address. Now,
mdiobus_scan() returns ERR_PTR(-ENODEV), which is caught by the
'if (IS_ERR(phydev))' condition and the loop exits immediately if the
PHY address does not contain PHY.
Repair this by explicitly checking for the ERR_PTR(-ENODEV) and if this
error comes around, continue with the next PHY address.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO devices can be stacked upon each other. The current code supports
two levels, which until recently has been enough for a DSA mdio bus on
top of another bus. Now we have hardware which has an MDIO mux in the
middle.
Define an MDIO MUTEX class with three levels.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bus = kzalloc() fails then we end up dereferencing bus when we do
"bus->irq[i] = PHY_POLL;". The code is a little simpler if we reverse
the NULL check and return directly on failure.
Fixes: e7f4dc3536 ('mdio: Move allocation of interrupts into core')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make device_free and device_remove operations in the mdio device
structure, so the core code does not need to differentiate between
phy devices and generic mdio devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that mdiobus_scan () will only find devices which have a
vendor/product ID in registers 2 and 3. These are typically PHY
devices. Other sort of MDIO devices, such as switches, are not
expected to be found during the scan.
Similarly, __mdiobus_register(), which calls mdiobus_scan() will only
find PHY devices, and other sorts of MDIO devices are expected to be
instantiated from device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should work with any sort of MDIO device which can be
probed on the bus, not just PHY devices. So generalise it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching a driver to a device has both generic parts, and parts which
are specific to PHY devices. Move the PHY specific parts into
phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO PM operations are really PHY device PM operations. So move
them into phy_device. This will be needed when we support devices on
the mdio bus which are not PHYs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio_bus exports three attributes:
- PHY ID is the unique 32-bits identifier for a MDIO device implementing
standard MII registers MII_PHYSID1/2, which is not guaranteed to be the
case for non-standard compliant devices (e.g: Ethernet switches)
- PHY interface describes the data-path of the PHY/MDIO device, which is
not strictly a PHY thing, but is required and needed for PHY devices to
function, a MDIO device could be a control device exclusively
- PHY has fixups describes what the PHY driver may have done, so
completely PHY specific
These are all phy attributes, not generic mdio attributes. So move the
attributes into the phy device code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nested variants of mdiobus_read/write are used in multiple
drivers, add nested variants in the mdiobus core.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the docbook comment for __mdiobus_register() to include the new
module owner argument. This resolves a warning found by the 0-day
builder.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdio_find_bus() leaks a struct device refcount, caused by using
class_find_device() and not realising that the device reference has
its refcount incremented:
* Note, you will need to drop the reference with put_device() after use.
...
while ((dev = class_dev_iter_next(&iter))) {
if (match(dev, data)) {
get_device(dev);
break;
}
Update the comment, and arrange for the phy code to drop this refcount
when disposing of a reference to it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not
the bus' parent.") uncovered a problem in mdiobus_unregister() which
leads to this warning when I reboot an APM Mustang (arm64) platform:
WARNING: CPU: 7 PID: 4239 at fs/sysfs/group.c:224 sysfs_remove_group+0xa0/0xa4()
sysfs group fffffe0000e07a10 not found for kobject 'xgene-mii-eth0:03'
...
CPU: 7 PID: 4239 Comm: reboot Tainted: G E 4.2.0-0.18.el7.test15.aarch64 #1
Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0 Aug 26 2015
Call Trace:
[<fffffe000009739c>] dump_backtrace+0x0/0x170
[<fffffe000009752c>] show_stack+0x20/0x2c
[<fffffe00007436f0>] dump_stack+0x78/0x9c
[<fffffe00000c2cb4>] warn_slowpath_common+0xa0/0xd8
[<fffffe00000c2d60>] warn_slowpath_fmt+0x74/0x88
[<fffffe0000293d3c>] sysfs_remove_group+0x9c/0xa4
[<fffffe00004a8bac>] dpm_sysfs_remove+0x5c/0x70
[<fffffe000049b388>] device_del+0x44/0x208
[<fffffe000049b578>] device_unregister+0x2c/0x7c
[<fffffe000050dc68>] mdiobus_unregister+0x48/0x94
[<fffffe000052afd0>] xgene_enet_mdio_remove+0x28/0x44
[<fffffe000052d3f0>] xgene_enet_remove+0xd0/0xd8
[<fffffe000052d424>] xgene_enet_shutdown+0x2c/0x3c
[<fffffe00004a204c>] platform_drv_shutdown+0x24/0x40
[<fffffe000049d4f4>] device_shutdown+0xf0/0x1b4
[<fffffe00000e31ec>] kernel_restart_prepare+0x40/0x4c
[<fffffe00000e32f8>] kernel_restart+0x1c/0x80
[<fffffe00000e3670>] SyS_reboot+0x17c/0x250
The problem is that mdiobus_unregister() deletes the bus device before
unregistering the phy devices on the bus. This wasn't a problem before
because the phys were not children of the bus:
/sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0:03
/sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0
But now that they are:
/sys/devices/platform/APMC0D05:00/net/eth0/xgene-mii-eth0/xgene-mii-eth0:03
when mdiobus_unregister deletes the bus device, the phy subdirs are
removed from sysfs also. So when the phys are unregistered afterward,
we get the warning. This patch changes the order so that phys are
unregistered before the bus device is deleted.
Fixes: 8b63ec1837 ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.")
Signed-off-by: Mark Salter <msalter@redhat.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We store c45 PHY's id information in c45_ids, so it should be used to
check the matching between PHY driver and PHY device for c45 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a call to ndo_close() a netdevice driver may call
phy_disconnect() -> phy_detach() -> phy_suspend(), such that the PHY is
suspsended at this point and a netdevice driver may clock gate the
backing peripheral providing MDIO bus accessses as well.
Update mdio_bus_phy_may_suspend() to return whether a PHY is allowed to
be suspended and conversely resumed if and only if it was not previously
suspended before while it is currently in detached (netdev pointer is
NULL) state.
This fixes bus errors seen during S2/S3 suspend/resume cycles for
netdevice drivers such as GENET which clock gates the entire Ethernet
MAC, including the MDIO bus block.
Acked-by: Fugang Duan <B38611@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are an abstraction on top of the PHY device
driver suspend and resume callbacks, utilize those since they are the
proper interface to suspending and resuming a PHY device.
Acked-by: Fugang Duan <B38611@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal PHYs may not have a valid PHY interface defined, which will
show up in sysfs as "". Add an explicit check of internal PHYs to report
their interface correctly.
Fixes: 3d055d8d1c ("net: phy: expose PHY device interface mode")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a71e3c3796 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:
root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>] lr : [<80361f44>] psr: 600f0013
sp : bceb7d70 ip : bceb7d88 fp : bceb7d84
r10: 8091523c r9 : 00000000 r8 : bd88f478
r7 : 803f8a88 r6 : 81165988 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : bd88f478 r0 : bd88f478
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 4cd1404a DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....
The problem with the original commit is explained by Russell King:
"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.
Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."
This reverts commit a71e3c3796.
Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdiobus_register() registers a device which is already bound to a driver.
Hence, the driver pointer should be set properly in order to track down
the driver associated to the MDIO bus.
This will be used to allow ethernet driver to pin down a MDIO bus driver,
preventing it from being unloaded while the PHY device is running.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to walk the list of subnodes of a mdio bus and look for
a node that matches the phy's address with its 'reg' property. If found,
set the of_node pointer for the phy. This allows auto-probed pyh
devices to be augmented by information passed in via DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 6d48f44b7b "mdio_bus: implement devm_mdiobus_alloc/devm_mdiobus_free"
introduced a new function devm_mdiobus_alloc_size() but added an export
for a different function devm_mdiobus_alloc(), which was obviously
a simple mistake that leads to build error whenever this function is
used from a loadable module:
ERROR: "devm_mdiobus_alloc_size" [drivers/net/ethernet/ti/davinci_mdio.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a resource managed devm_mdiobus_alloc[_size]()/devm_mdiobus_free()
to automatically clean up MDIO bus alocations made by MDIO drivers,
thus leading to simplified MDIO drivers code.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
