Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string, which describes the parallel
LCD.
Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6sx-sdb has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 1006ed7e1b ("serial: imx: Use generic uart-has-rtscts
DT property"), the Freescale IMX UART driver recognizes the generic
"uart-has-rtscts" DT property, deprecating the vendor-specific
"fsl,uart-has-rtscts" DT property. Hence replace the latter by the
former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds node i2c bus 3 to get the appropriate userland device
file. So for prototyping it's possible to experiment within userland.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx6sx sdb board has two revisions, the current mainline one
is reva which is experimental and mainly for internal use. In
this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and
move the reva dedicated contents to imx6sx-sdb-reva.dts.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
