Report the number of successful and failed insertions, and also the
current count of filters, to aid in tuning e.g. rps_flow_cnt.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In high connection count usage, the NIC's filter table may be filled with
sufficiently many ARFS filters that further insertions fail. As this
does not represent a correctness issue, do not log the resulting MCDI
errors. Add a debug-level message under the (by default disabled)
rx_status category instead; and take the opportunity to do a little extra
expiry work.
Since there are now multiple workitems able to call __efx_filter_rfs_expire
on a given channel, it is possible for them to race and thus pass quotas
which, combined, exceed rfs_filter_count. Thus, don't WARN_ON if we loop
all the way around the table with quota left over.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: David Ahern <dahern@digitalocean.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The old rfs_filters_added method for determining the quota could potentially
allow the NIC to become filled with old filters, which never get tested for
expiry. Instead, explicitly make expiry check work depend on the number of
filters installed, and don't count checking slots without filters in as
doing work. This guarantees that each filter will be checked for expiry at
least once every thirty seconds (assuming the channel to which it belongs is
NAPI polling actively) regardless of fill level.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: David Ahern <dahern@digitalocean.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Jeff Kirsher says:
====================
This series contains updates to the ice driver only.
Bruce updates the driver to store the number of functions the device has
so that it won't have to compute it when setting safe mode capabilities.
Adds a check to adjust the reporting of capabilities for devices with
more than 4 ports, which differ for devices with less than 4 ports.
Brett adds a helper function to determine if the VF is allowed to do
VLAN operations based on the host's VF configuration. Also adds a new
function that initializes VLAN stripping (enabled/disabled) for the VF
based on the device supported capabilities. Adds a check if the vector
index is valid with the respect to the number of transmit and receive
queues configured when we set coalesce settings for DCB. Adds a check
if the promisc_mask contains ICE_PROMISC_VLAN_RX or ICE_PROMISC_VLAN_TX
so that VLAN 0 promiscuous rules to be removed. Add a helper macro for
a commonly used de-reference of a pointer to &pf->dev->pdev.
Jesse fixes an issue where if an invalid virtchnl request from the VF,
the driver would return uninitialized data to the VF from the PF stack,
so ensure the stack variable is initialized earlier. Add helpers to the
virtchnl interface make the reporting of strings consistent and help
reduce stack space. Implements VF statistics gathering via the kernel
ndo_get_vf_stats().
Akeem ensures we disable the state flag for each VF when its resources
are returned to the device.
Tony does additional cleanup in the driver to ensure the when we
allocate and free memory within the same function, we should not be
using devm_* variants; use regular alloc and free functions.
Henry implements code to query and set the number of channels on the
primary VSI for a PF via ethtool.
Jake cleans up needless NULL checks in ice_sched_cleanup_all().
Kevin updates the firmware API version to align with current NVM images.
v2: Added "Fixes:" tag to patch 5 commit description and added the use
of netif_is_rxfh_configured() in patch 13 to see if RSS has been
configured by the user, if so do not overwrite that configuration.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Implement and export UDP segmentation offload (USO) support for both
NIC and MQPRIO QoS offload Tx path. Update appropriate logic in Tx to
parse GSO info in skb and configure FW_ETH_TX_EO_WR request needed to
perform USO.
v2:
- Remove inline keyword from write_eo_udp_wr() in sge.c. Let the
compiler decide.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The FW_ETH_TX_EO_WR used for sending UDP Segmentation Offload (USO)
requests expects the headers to be part of the descriptor and the
payload to be part of the SGL containing the DMA mapped addresses.
Hence, the DMA address in the first entry of the SGL can start after
the packet headers. Currently, unmap_sgl() tries to unmap from this
wrong offset, instead of the originally mapped DMA address.
So, use existing unmap_skb() instead, which takes originally saved DMA
addresses as input. Update all necessary Tx paths to save the original
DMA addresses, so that unmap_skb() can unmap them properly.
v2:
- No change.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Update FW API minor version to align to current value advertised
by FW in new NVM images.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in ice_sched_cleanup_all checks whether the port info is NULL
prior to calling ice_sched_clear_port. However, ice_sched_clear_port
already checks whether port info is non-NULL.
More importantly, it also checks whether the port structure has been
initialized by checking its port_state field as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively. Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When code reaches the "out" label, n is guaranteed to be valid so we can
unconditionally call neigh_release.
Also change the label to release_neigh to better reflect the fact that
we unconditionally free the neighbour and also match other labels
convention.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Improve mlx5e_route_lookup_ipv6 function structure by avoiding #ifdef then
return -EOPNOTSUPP in the middle of the function code.
To do so, we stub out mlx5e_tc_tun_create_header_ipv6 which is the only
caller of this helper function to avoid calling it altogether
when ipv6 is compiled out, which should also cleanup some compiler
warnings of unused variables.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor flex parser tunnel code:
- Add definition for flex parser tunneling header for VXLAN-GPE
- Use macros for VXLAN-GPE SW steering when building STE
- Refactor the code to reflect that this is a VXLAN GPE
only code and not a general flex parser code.
This also significantly simplifies addition of more
flex parser protocols, such as Geneve.
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The MODIFY_HCA_VPORT_CONTEXT uses field_selector to mask fields needed
to be written, other fields are required to be zero according to the
HW specification. The supported fields are controlled by bitfield
and limited to vport state, node and port GUIDs.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the
ip -s link show dev <PF> command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtchannel interface was repeating a lot of strings
and wasting storage space in the kernel. There was also
inconsistent messages for the same thing. Consolidate all
those messages and bit checks into a couple of helper functions.
Also, reduce stack space usage by simplifying getting the pointer
to the pf using a helper.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.
Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_clear_vsi_promisc() detects if the VLAN ID sent is not 0
and sets the recipe_id to ICE_SW_LKUP_PROMISC_VLAN in that case and
ICE_SW_LKUP_PROMISC if the VLAN_ID is 0. However this doesn't allow VLAN
0 promiscuous rules to be removed, but they can be added. Fix this by
checking if the promisc_mask contains ICE_PROMISC_VLAN_RX or
ICE_PROMISC_VLAN_TX. This change was made to match what is being done
for ice_set_vsi_promisc().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug. Fix by initializing the stack variable
earlier in the function before any return paths can be taken.
Fixes: 1071a8358a ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when adding/deleting vlans in ice_vc_process_vlan_msg()
we are calling ice_vsi_manage_vlan_stripping() to enable/disable
when adding and deleting a VLAN respectively. This is wrong
because adding/deleting VLANs has nothing to do with configuring
VLAN stripping. VLAN stripping is configured through the
following VIRTCHNL operations:
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Unfortunately we can't just remove this because then stripping
will never be configured on VF initialization. Fix this by
adding a new function that initializes (disables/enables) VLAN
stripping for the VF based on the device supported capabilities.
This allows us to remove the call to
ice_vsi_manage_vlan_stripping() in ice_vc_process_vlan_msg().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the host disables VLAN offloads on the VF by
not setting the VIRTCHNL_VF_OFFLOAD_VLAN capability bit
we will still honor VF VLAN configuration messages over
VIRTCHNL. These messages (i.e. enable/disable VLAN stripping
and VLAN filtering) should be blocked when the feature
is not supported. Fix that by adding a helper function to
determine if the VF is allowed to do VLAN operations based
on the host's VF configuration.
Also, mirror the VF communicated capabilities in the host's
VF configuration.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Firmware always returns 8 as the max number of supported TCs. However on
devices with more than 4 ports, the maximum number of TCs per port is
limited to 4. Check and, if necessary, correct the reporting of
capabilities for devices with more than 4 ports.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the number of functions the device has and use this number when
setting safe mode capabilities instead of calculating it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Co-developed-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following sparse warnings:
drivers/net/dsa/ocelot/felix.c:351:6: warning: symbol 'felix_txtstamp' was not declared. Should it be static?
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 8481141246 ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function m_can_runtime_resume() is getting recursively called from
m_can_class_resume(). This results in a lock up.
We need not call m_can_class_resume() during m_can_runtime_resume().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When virt_wifi interface is created, virt_wifi_newlink() is called and
it calls register_netdevice().
if register_netdevice() fails, it internally would call
->priv_destructor(), which is virt_wifi_net_device_destructor() and
it frees netdev. but virt_wifi_newlink() still use netdev.
So, use-after-free would occur in virt_wifi_newlink().
Test commands:
ip link add dummy0 type dummy
modprobe bonding
ip link add bonding_masters link dummy0 type virt_wifi
Splat looks like:
[ 202.220554] BUG: KASAN: use-after-free in virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.221659] Read of size 8 at addr ffff888061629cb8 by task ip/852
[ 202.222896] CPU: 1 PID: 852 Comm: ip Not tainted 5.4.0-rc5 #3
[ 202.223765] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 202.225073] Call Trace:
[ 202.225532] dump_stack+0x7c/0xbb
[ 202.226869] print_address_description.constprop.5+0x1be/0x360
[ 202.229362] __kasan_report+0x12a/0x16f
[ 202.230714] kasan_report+0xe/0x20
[ 202.232595] virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.233370] __rtnl_newlink+0xb9f/0x11b0
[ 202.244909] rtnl_newlink+0x65/0x90
[ ... ]
Cc: stable@vger.kernel.org
Fixes: c7cdba31ed ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20191121122645.9355-1-ap420073@gmail.com
[trim stack dump a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If negotiated NVSP version <= NVSP_PROTOCOL_VERSION_6, the offset may
be wrong (too small) due to a host bug. This can cause missing the
end of the send indirection table, and add multiple zero entries from
leading zeros before the data region. This bug adds extra burden on
channel 0.
So fix the offset by computing it from the data structure sizes. This
will ensure netvsc driver runs normally on unfixed hosts, and future
fixed hosts.
Fixes: 5b54dac856 ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reach the data region, the existing code adds offset in struct
nvsp_5_send_indirect_table on the beginning of this struct. But the
offset should be based on the beginning of its container,
struct nvsp_message. This bug causes the first table entry missing,
and adds an extra zero from the zero pad after the data region.
This can put extra burden on the channel 0.
So, correct the offset usage. Also add a boundary check to ensure
not reading beyond data region.
Fixes: 5b54dac856 ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While using ARCH=mips CROSS_COMPILE=mips-linux-gnu- command to compile,
make C=2 drivers/net/ethernet/freescale/enetc/enetc.o
one warning can be found:
drivers/net/ethernet/freescale/enetc/enetc.c:1439:5:
warning: symbol 'enetc_setup_tc_mqprio' was not declared.
Should it be static?
This patch make symbol enetc_setup_tc_mqprio static.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing netvsc_detach() and netvsc_attach() APIs make it easy to
implement the suspend/resume callbacks.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to use ocelot_port_add_txtstamp_skb() for adding skbs which
require TX timestamp into list. Export it so that DSA Felix driver
could reuse it too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method getting TX timestamp by reading timestamp FIFO and
matching skbs list is common for DSA Felix driver too.
So move code out of ocelot_board.c, convert to use
ocelot_get_txtstamp() function and export it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export ocelot_hwstamp_get/set functions so that DSA driver
is able to reuse them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue only exists for the primary PF. For other functions
we hit a WARN_ON in kernel/workqueue.c.
Fixes: 7c236c43b8 ("sfc: Add support for IEEE-1588 PTP")
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rvu_get_blkaddr() fails, then this rvu_cgx_nix_cuml_stats() returns
zero and we write some uninitialized data into the debugfs output.
On the error paths, the use of the uninitialized "*stat" is harmless,
but it will lead to a Smatch warning (static analysis) and a UBSan
warning (runtime analysis) so we should prevent that as well.
Fixes: f967488d09 ("octeontx2-af: Add per CGX port level NIX Rx/Tx counters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ampdu locking code does not unlock its mutex in the early
return case. This patch fixes it.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when the board does not support GPIOs for these
signals.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM. It seems rather common that GPON modules
mis-report.
Let's fix these modules by adding some quirks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for applying module quirks to the list of supported
ethtool link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl3VowIACgkQSD+KveBX
+j7cZgf/aEWFOw6e9oaELHqsWYWaqBabAh/celXLIVx7in1JR5oCGSQHRAH/5JB2
HHfvXvN5Yk9YNga5HtT4mqZS6NsgYksG3pneuJApLcbY627pAzlw2i90yqIKz8In
svulz/BBv22msxk/F2ZyQ04zltiNplrHI1ESbxmMhLuhRA5M9AwRTjfa2Uk6kbLj
pmwmAEymNsxNfRfL4/sVMXgbUcTOkf38h4qAWKTnUZeCFCVk2pbIjBkNTQ6eG+kY
rbYYqMyhqusGhvkiP083rdnu9aKmVUG55jIyd00PhrrVow9HSTKwNqlcq/+qtYpE
H5dhgxJexrXJd02m+KK2h+DZxPsHDA==
=t0rV
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-11-20
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5e: Fix set vf link state error flow')
For -stable v4.14
('net/mlxfw: Verify FSM error code translation doesn't exceed array size')
For -stable v4.19
('net/mlx5: Fix auto group size calculation')
For -stable v5.3
('net/mlx5e: Fix error flow cleanup in mlx5e_tc_tun_create_header_ipv4/6')
('net/mlx5e: Do not use non-EXT link modes in EXT mode')
('net/mlx5: Update the list of the PCI supported devices')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only values 0 and 1 are currently defined as parameters for
PHY_MDIO_CHG. Instead of silently ignoring unknown values and
misinterpreting the firmware code let's explicitly check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using macro FIELD_SIZEOF makes this define easier understandable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're not in atomic context here, therefore switch to msleep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both rtl_work_func_t() and rtl8152_close() call napi_disable().
Since the two calls aren't protected by a lock, if the close
function starts executing before the work function, we can get into a
situation where the napi_disable() function is called twice in
succession (first by rtl8152_close(), then by set_carrier()).
In such a situation, the second call would loop indefinitely, since
rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED
bit.
The rtl8152_close() function in turn issues a
cancel_delayed_work_sync(), and so it would wait indefinitely for the
rtl_work_func_t() to complete. Since rtl8152_close() is called by a
process holding rtnl_lock() which is requested by other processes, this
eventually leads to a system deadlock and crash.
Re-order the napi_disable() call to occur after the work function
disabling and urb cancellation calls are issued.
Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e
Reported-by: http://crbug.com/1017928
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving many or larger packets, e.g. when doing a file download,
it was observed that the read buffer size register reports up to 4 bytes
more than the current define allows in the check.
If this is the case, then no data transfer is initiated to receive the
packets (and thus to empty the buffer) which results in a stall of the
interface.
These 4 bytes are a hardware generated frame length which is prepended
to the actual frame, thus we have to respect it during our check.
Fixes: 026b907d58 ("net: qca_spi: Add available buffer space verification")
Signed-off-by: Michael Heimpold <michael.heimpold@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reversion of commit 11d49ce9f7
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) leaves us
calling H_EOI even in XIVE mode. That will fail with H_FUNCTION
because H_EOI is not supported in that mode. That failure is
harmless. Ignore it so we can use common code for both XICS and
XIVE.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11d49ce9f7
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) since that
has the unintended effect of changing the interrupt priority
and emits warning when running in legacy XICS mode.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of costly dma_sync_single_for_device in mvneta_rx_refill
since now the driver can let page_pool API to manage needed DMA
sync with a proper size.
- XDP_DROP DMA sync managed by mvneta driver: ~420Kpps
- XDP_DROP DMA sync managed by page_pool API: ~585Kpps
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rely on page_pool_recycle_direct and not on xdp_return_buff in
mvneta_run_xdp. This is a preliminary patch to limit the dma sync len
to the one strictly necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array mlxfw_fsm_state_err_str contains value to string translation, when
values are provided by mlxfw_dev. If value is larger than
MLXFW_FSM_STATE_ERR_MAX, return "unknown error" as expected instead of
reading an address than exceed array size.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the upcoming ConnectX-6 LX device ID.
Fixes: 85327a9c41 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Shani Shapp <shanish@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Once all the large flow groups (defined by the user when the flow table
is created - max_num_groups) were created, then all the following new
flow groups will have only one flow table entry, even though the flow table
has place to larger groups.
Fix the condition to prefer large flow group.
Fixes: f0d22d1874 ("net/mlx5_core: Introduce flow steering autogrouped flow table")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Device that doesn't support IP-in-IP offloads has to filter csum and gso
offload support, otherwise kernel will conclude that device is capable of
offloading csum and gso for IP-in-IP tunnels and that might result in
IP-in-IP tunnel not functioning.
Fixes: 25948b87dd ("net/mlx5e: Support TSO and TX checksum offloads for IP-in-IP")
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On some old Firmwares, connector type value was not supported, and value
read from FW was 0. For those, driver used link mode in order to set
connector type in link_ksetting.
After FW exposed the connector type, driver translated the value to ethtool
definitions. However, as 0 is a valid value, before returning PORT_OTHER,
driver run the check of link mode in order to maintain backward
compatibility.
Cited patch added support to EXT mode. With both features (connector type
and EXT link modes) ,if connector_type read from FW is 0 and EXT mode is
set, driver mistakenly compare EXT link modes to non-EXT link mode.
Fixed that by skipping this comparison if we are in EXT mode, as connector
type value is valid in this scenario.
Fixes: 6a89737241 ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Before this commit the ndo always returned success.
Fix that.
Fixes: 1ab2068a4c ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an ste hash table has too many collision we enlarge it
to a bigger hash table (rehash). Rehashing collision improvement
depends on the bytemask value. The more 1 bits we have in bytemask
means better spreading in the table.
Without this fix tables can grow in size without providing any
improvement which can lead to memory depletion and failures.
This patch will limit table rehash to reduce memory and improve
the performance.
Fixes: 41d0707415 ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The byte mask fields affect on the hash index distribution,
when the byte mask is zero, the hash calculation will always
be equal to the same index.
To avoid unneeded rehash of hash tables mark the table to skip
rehash.
This is needed by the next patch which will limit table rehash
to reduce memory consumption.
Fixes: 41d0707415 ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When creating a CQ, the CPU id is used for the vector value.
This would fail in-case the CPU id was higher than the maximum
vector value.
Fixes: 297cccebdc ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mirred action parsing code in parse_tc_fdb_actions() first checks if
out_dev has same parent id, and only verifies that there is a pending encap
action that was parsed before. Recent change in vxlan module made function
netdev_port_same_parent_id() to return true when called for mlx5 eswitch
representor and vxlan device created explicitly on mlx5 representor
device (vxlan devices created with "external" flag without explicitly
specifying parent interface are not affected). With call to
netdev_port_same_parent_id() returning true, incorrect code path is chosen
and encap rules fail to offload because vxlan dev is not a valid eswitch
forwarding dev. Dmesg log of error:
[ 1784.389797] devices ens1f0_0 vxlan1 not on same switch HW, can't offload forwarding
In order to fix the issue, rearrange conditional in parse_tc_fdb_actions()
to check for pending encap action before checking if out_dev has the same
parent id.
Fixes: 0ce1822c2a ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current code uses the old method of prio encoding in
flow_cls_common_offload. Fix to follow the changes introduced in
commit ef01adae0e ("net: sched: use major priority number as hardware priority").
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Be sure to release the neighbour in case of failures after successful
route lookup.
Fixes: 101f4de9dd ("net/mlx5e: Move TC tunnel offloading code to separate source file")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add TC-MATCHALL classifier ingress offload support. The same actions
supported by existing TC-FLOWER offload can be applied to all incoming
traffic on the underlying interface.
Ensure the rule priority doesn't conflict with existing rules in the
TCAM. Only 1 ingress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually.
v3:
- No change.
v2:
- Removed logic to fetch free index from end of TCAM. Must maintain
same ordering as in kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only offload rule if it satisfies both of the following conditions:
1. The immediate previous rule has priority <= current rule's priority.
2. The immediate next rule has priority >= current rule's priority.
Also rework free entry fetch logic to search from end of TCAM, instead
of beginning, because higher indices have lower priority than lower
indices. This is similar to how TC auto generates priority values.
v5:
- Fixed commit message and comment to include comparison for equal
priority.
v4:
- Patch added in this version.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TC-MATCHALL classifier offload with TC-POLICE action applied for
all outgoing traffic on the underlying interface. Split flow block
offload to support both egress and ingress classification.
For example, to rate limit all outgoing traffic to 1 Gbps:
$ tc qdisc add dev enp2s0f4 clsact
$ tc filter add dev enp2s0f4 egress matchall skip_sw \
action police rate 1Gbit burst 8Kbit
Note that skip_sw is important. Otherwise, both stack and hardware
will end up doing policing. Policing can't be shared across flow
blocks. Only 1 egress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Removed check to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function.
v3:
- Added check to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK.
v2:
- Added check to reject flow block sharing for policers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once every napi poll cycle, check if numa node is different than
the page pool's numa id, and update it using page_pool_update_nid().
Alternatively, we could have registered an irq affinity change handler,
but page_pool_update_nid() must be called from napi context anyways, so
the handler won't actually help.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW switchdev based driver which is operating in dual-emac mode by
default, thus working as 2 individual network interfaces. The Switch mode
can be enabled by configuring devlink driver parameter "switch_mode" to 1:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdevs - UP/DOWN, but
Port's netdev devices have to be UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely
reloads its configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name ale_bypass type driver-specific
values:
cmode runtime value false
- "ale_bypass" devlink driver parameter allows to enable
ALE_CONTROL(4).BYPASS mode for debug purposes.
- updated DT bindings.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common functions to cpsw-priv.c so that they can be used across both
drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patches introduce new CPSW switchdev driver which uses common
code with legacy CPSW driver. This will introduce build dependency between
CPSW switchdev and CPSW legacy drivers related to for_each_slave() and
cpsw_slave_index() - they can be compiled both, but only one of them will
be not functional depending in Kconfig settings due to duffrences in Slave
Ports indexes calculation.
To fix this make for_each_slave() local (it's used now only by legacy CPSW
driver) and convert cpsw_slave_index() to be a function pointer which is
assigned in probe. Driver to probe is defined by DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patch introduces switchdev functionality, so modify
ALE engine VLANs/MDBs API:
- cpsw_ale_del_mcast(): update so it will remove only selected ports from
mcast port_mask or delete whole mcast record if !port_mask
- cpsw_ale_del_vlan(): update so it will remove only selected ports from
all VLAN record's masks or delete whole VLAN record if !port_mask
- add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's
masks
- add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now untagged vlan traffic is not support on Host P0 port. This patch adds
in ALE context bitmap of VLANs for which Host P0 port bit set in Force
Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding
check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete
or garbage entries from ALE table.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if they are not currently used fix BK/BE endpoint definition order.
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Parse configured {tx,rx} mask from eeprom data instead of just setting it
to four tx-rx streams
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_get_antenna in mac80211.c in order to be reused by all
drivers. Initialize .get_antenna function pointer for mt76x0, mt7603,
mt7615 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible out-of-bound access of status rates array in
mt7615_fill_txs/mt7603_fill_txs routines
Fixes: c5211e997e ("mt76: mt7603: rework and fix tx status reporting")
Fixes: 4af81f02b4 ("mt76: mt7615: sync with mt7603 rate control changes")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit 34b0e9b767.
Since commit 7bd0650be6 ("mt76: dma: fix buffer unmap with non-linear skbs")
is no longer necessary to disable HW encryption for MT7630E.
Disabling HW encryption helped previously because somehow fragmented
skb's are not created if mac80211 encrypt frames, so buffer unmap bug
of non-linear skbs was not triggered. Now since this bug is properly
fixed by commit 7bd0650be6 ("mt76: dma: fix buffer unmap with
non-linear skbs") , we can enable HW encryption back.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set switch_reason to CH_SWITCH_SCAN_BYPASS_DPD during frequency scanning
in order to disable radar pattern detector
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move interface modes declaration in common code since now mt76
chipsets support all modes (NL80211_IFTYPE_STATION, NL80211_IFTYPE_AP,
NL80211_IFTYPE_MESH_POINT and NL80211_IFTYPE_ADHOC)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable IFTYPE_ADHOC support on 7615 devices. The feature has been tested
using a mt76x2 device as wireless peer.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move SUPPORTS_REORDERING_BUFFER hw property configuration from chip
specific code to mt76_register_device since it is supported by all mt76
drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Convert mt76_is_mmio and mt76_is_usb to rely on mt76_dev instead of
mt76x02_dev since this is a property not strictly related to hw chipset
and it will be more reusable
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/dma.c: In function mt76_dma_rx_fill:
drivers/net/wireless/mediatek/mt76/dma.c:377:6: warning: variable idx set but not used [-Wunused-but-set-variable]
It is not used since commit 17f1de56df ("mt76:
add common code shared between multiple chipsets")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
rate controller and throughput are very sensitive to tx status timing.
In order to improve performances when the system is heavily loaded,
substitute stat_work delayed_work with a regular work_struct and create
a mt76u dedicated workqueue for tx status reporting
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
usb drivers are supposed to communicate using usb_interface instead
mt76x{0,2}u is now registering through usb_device. Fix it by passing
usb_intf device to mt76_alloc_device routine.
Fixes: 112f980ac8 ("mt76usb: use usb_dev private data")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-By: Zero_Chaos <sidhayn@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
remove unneeded semicolon.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since mt76x0 does not save the phy calibration data it is not necessary
to wait 350ms in mt76x0_phy_calibrate
Tested-by: Sid Hayn <sidhayn@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update ewma packet length in mt76x02u_tx_prepare_skb as it is
done for pci counterpart in order to properly estimate tx time on
current channel
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x0e driver only supports MAC addresses from
calibration data eeprom. Many routers however do not
have a valid stock address set in this field.
This patch makes it possible to take a MAC address
from OF (e.g. from mtd).
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[adjusted for kernel submission]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
if napi_complete() returns false, it means that polling is still pending.
Interrupts should not fire until the polling is no longer scheduled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cancel the workqueue after the tid has been cleaned up, in order to
avoid a possible rescheduling from within the work function.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A rcu read locked section is not allowed to sleep, and the rcu lock here
isn't actually necessary, because we're holding dev->mutex.
Fixes an issue when the tid work item is still running while freeing
a station or stopping the aggregation session
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With the devm API, the unregister happens after the device cleanup is done,
after which the struct mt76_dev which contains the led_cdev has already been
freed. This leads to a use-after-free bug that can crash the system.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Poll per-station hardware counters available in WTBL after tx/rx
status events in order to report tx/rx airtime to mac80211 layer
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_mac_wtbl_update utility routine in order to update
WTBL update register
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Like on mt7603, MIB status register 16 tracks CCA time, but does not
include tx time. Switch to status register 9 to includ NAV and tx
time as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Report tx time/rx time and obss time from hw mib counters to fill survey
info requested by mac80211
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Host time is used to calculate the channel active time on mt7603 and mt7615.
Use the same on mt76x02 and move the lock to core code to get rid of some
duplicated code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MT_MIB_STAT_PSCCA only counts rx CCA busy time, which does not include
tx time. MT_MIB_STAT_CCA counts full busy time, including Rx, Tx and NAV
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Report total rx airtime for valid stations as BSS rx time in survey
mt7615 is left out for now, it will be supported later by reading
hardware counters instead of calculating airtime in software
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_channel_state() from mt76.h to mac80211.c
Preparation for updating channel state from more places in the drivers/core
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce ampdu_stat entry in mt7603 debugfs in order to dump 802.11
aggr cumulative statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce ampdu_stat entry in mt7615 debugfs in order to dump 802.11
aggr cumulative statistics
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move aggr_stats array from mt76x02_dev to mt76_dev in order to be reused
adding aggregation stats for mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt7615_queues_read routine to dump hw queue related info.
Add hw ac queues statistics in mt7615 debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move queue debugfs entry to driver specific code since mt7615 devices
rely on a different queue layout
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify mt76x02u_mac_start between mt76x2u and mt76x0u since the
code is shared between both drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x02_mac_reset_counters from mt76x0_init_hardware since
it will be run starting the device
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_reset_counters in mt76x02_mac_start and get rid of
mt76x2_mac_start since it is just a wrapper for mt76x02_mac_start
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify mac_reset_counter routine and move it in mt76x02_lib module
since it is shared by all mt76x02 drivers (pci/usb)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable Smart Carrier Sense algorithm by default in order to improve
performances in a noisy environment
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't populate the array mt76x0_chan_map on the stack but instead make it
static const. Makes the object code smaller by 80 bytes.
Before:
text data bss dec hex filename
7685 1192 0 8877 22ad mediatek/mt76/mt76x0/eeprom.o
After:
text data bss dec hex filename
7541 1256 0 8797 225d mediatek/mt76/mt76x0/eeprom.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce lockdep_assert_held macro in __mt76u_vendor_request routine
and remove comments regarding usb_ctrl_mtx lock
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove empty flag in mt76_txq_schedule_list and mt76_txq_send_burst
since we just need retry_q length to notify mac80211 to reschedule the
current tx queue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
kasprintf() can fail, we should check the return value.
Fixes: 5ed540aecc ("iwlwifi: use mac80211 throughput trigger")
Fixes: 8ca151b568 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no multicast wake lock in the driver, remove the comment
that refers to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We trace the whole TFD with all TBs when in iwlwifi_dev_tx,
but sometimes we add TBs to it later and then we don't have
any of this data. Trace the I/O virtual address (IOVA) (it
can be the physical address, or as returned by the IOMMU)
here to aid debugging the DMA flows.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to check 'priv->bt_ant_couple_ok' twice in
rs_bt_update_lq(). The second check is always true. Thus, the
expression can be simplified.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes it easier for user-space to know how many antennas the
radio has. Seems to work with the AX200 radio, at least.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is a little less efficient now as it's known to be a
multiqueue device in this function, but a future patch will
have to use a variable here anyway, so use rxq->queue_size
now instead to make it clearer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This email alias (ilw@linux.intel.com) hasn't been functional
for probably closer to a decade than not, remove it. It's not
really clear to me how this ended up in new code though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
