[ Upstream commit d8e193f13b07e6c0ffaa1a999386f1989f2b4c5e ]
If the card has not been power cycled, it may still be using 1.8V
signaling. This situation is detected in mmc_sd_init_card function and
should be handled in mmci stm32 variant. The host->pwr_reg variable is
also correctly protected with spin locks.
Fixes: 94b94a93e3 ("mmc: mmci_sdmmc: Implement signal voltage callbacks")
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210701143353.13188-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f8203b4be1937c4939bb98623e67dcfd7da4d1 ]
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 10252bae863d09b9648bed2e035572d207200ca1 upstream.
There's a chance that the IDA allocated in mmc_alloc_host() is not freed
for some time because it's freed as part of a class' release function
(see mmc_host_classdev_release() where the IDA is freed). If another
thread is holding a reference to the class, then only once all balancing
device_put() calls (in turn calling kobject_put()) have been made will
the IDA be released and usable again.
Normally this isn't a problem because the kobject is released before
anything else that may want to use the same number tries to again, but
with CONFIG_DEBUG_KOBJECT_RELEASE=y and OF aliases it becomes pretty
easy to try to allocate an alias from the IDA twice while the first time
it was allocated is still pending a call to ida_simple_remove(). It's
also possible to trigger it by using CONFIG_DEBUG_KOBJECT_RELEASE and
probe defering a driver at boot that calls mmc_alloc_host() before
trying to get resources that may defer likes clks or regulators.
Instead of allocating from the IDA in this scenario, let's just skip it
if we know this is an OF alias. The number is already "claimed" and
devices that aren't using OF aliases won't try to use the claimed
numbers anyway (see mmc_first_nonreserved_index()). This should avoid
any issues with mmc_alloc_host() returning failures from the
ida_simple_get() in the case that we're using an OF alias.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Fixes: fa2d0aa969 ("mmc: core: Allow setting slot index via device tree alias")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-3-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09247e110b2efce3a104e57e887c373e0a57a412 upstream.
While initializing an UHS-I SD card, the mmc core first tries to switch to
1.8V I/O voltage, before it continues to change the settings for the bus
speed mode.
However, the current behaviour in the mmc core is inconsistent and doesn't
conform to the SD spec. More precisely, an SD card that supports UHS-I must
set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
response. When switching to 1.8V I/O the mmc core correctly checks both of
the bits, but only the SD_OCR_S18R bit when changing the settings for bus
speed mode.
Rather than actually fixing the code to confirm to the SD spec, let's
deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
parts. This enables us to support UHS-I for SDSC cards (outside spec),
which is actually being supported by some existing SDSC cards. Moreover,
this fixes the inconsistent behaviour.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
Cc: stable@vger.kernel.org
[Ulf: Rewrote commit message and comments to clarify the changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77347eda64ed5c9383961d1de9165f9d0b7d8df6 upstream.
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0244847f9fc5e20df8b7483c8a4717fe0432d38 upstream.
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c7 ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ee6782e045645abd9180ab9369b01293d862bd upstream.
On the Toshiba Encore 2 WT8-B the microSD slot always reports the card
being write-protected even though microSD cards do not have a write-protect
switch at all.
Add a new DMI_QUIRK_SD_NO_WRITE_PROTECT quirk entry to sdhci-acpi.c's
DMI quirk table for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210503092157.5689-1-hdegoede@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0bb3107703d2c58f7a0a7a2060bb57bc120326 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b52f09080565030a530a784f1c9948a7f48ca3 upstream.
According to the eMMC Spec:
"When command queuing is enabled (CMDQ Mode En bit in CMDQ_MODE_EN
field is set to ‘1’) class 11 commands are the only method through
which data transfer tasks can be issued. Existing data transfer
commands, namely CMD18/CMD17 and CMD25/CMD24, are not supported when
command queuing is enabled."
which means if CMDQ is enabled, the FFU commands will not be supported.
To fix this issue, just simply disable CMDQ on the ioctl path, and
re-enable CMDQ once ioctl request is completed.
Tested-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210504203209.361597-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f9ae69e5267f53e89e296fccee291975a85f0eb ]
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 961470820021e6f9d74db4837bd6831a1a30341b ]
The sdhci_sprd_writew() was defined by never used in sdhci_ops:
drivers/mmc/host/sdhci-sprd.c:134:20: warning: unused function 'sdhci_sprd_writew'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601095403.236007-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 103a5348c22c3fca8b96c735a9e353b8a0801842 upstream.
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
[1] 285133040e6c ("arm64: Import latest memcpy()/memmove() implementation")
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210609150230.9291-1-narmstrong@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6687cd72aa9112a454a4646986e0402dd1b07d0e upstream.
R-Car M3-W ES3.0 is marketed as R-Car M3-W+ (R8A77961), and has its own
compatible value "renesas,r8a77961".
Hence using soc_device_match() with soc_id = "r8a7796" and revision =
"ES3.*" does not actually match running on an R-Car M3-W+ SoC.
Fix this by matching with soc_id = "r8a77961" instead.
Fixes: a38c078fea ("mmc: renesas_sdhi: Avoid bad TAP in HS400")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/ee8af5d631f5331139ffea714539030d97352e93.1622811525.git.geert+renesas@glider.be
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c9017d0b5d3fbf17e69577a42d9e610ca122810 upstream.
We have to bring the eMMC from sending-data state back to transfer state
once we detected a CRC error (timeout) during tuning. So, send a stop
command via mmc_abort_tuning().
Fixes: 4f11997773 ("mmc: tmio: Add tuning support")
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210602073435.5955-1-wsa+renesas@sang-engineering.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1149a6c06ee094a6e62886b0c0e8e66967a728a upstream.
Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f0bdf98fab058efe7bf49732f70a0f26d1143154 ]
Remove the CQHCI_QUIRK_SHORT_TXFR_DESC_SZ quirk because the
latest chips have this fixed and earlier chips have other
CQE problems that prevent the feature from being enabled.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210325192834.42955-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f410ee0aa2df050a9505f5c261953e9b18e21206 ]
When imx_data->pinctrl is not a valid pointer, pinctrl_lookup_state
will trigger kernel panic.
When we boot Dual OS on Jailhouse hypervisor, we let the 1st Linux to
configure pinmux ready for the 2nd OS, so the 2nd OS not have pinctrl
settings.
Similar to this commit b62eee9f80 ("mmc: sdhci-esdhc-imx: no fail when no pinctrl available").
Reviewed-by: Bough Chen <haobo.chen@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1614222604-27066-6-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 17a17bf50612e6048a9975450cf1bd30f93815b5 upstream.
The mmc core uses a PM notifier to temporarily during system suspend, turn
off the card detection mechanism for removal/insertion of (e)MMC/SD/SDIO
cards. Additionally, the notifier may be used to remove an SDIO card
entirely, if a corresponding SDIO functional driver don't have the system
suspend/resume callbacks assigned. This behaviour has been around for a
very long time.
However, a recent bug report tells us there are problems with this
approach. More precisely, when receiving the PM_SUSPEND_PREPARE
notification, we may end up hanging on I/O to be completed, thus also
preventing the system from getting suspended.
In the end what happens, is that the cancel_delayed_work_sync() in
mmc_pm_notify() ends up waiting for mmc_rescan() to complete - and since
mmc_rescan() wants to claim the host, it needs to wait for the I/O to be
completed first.
Typically, this problem is triggered in Android, if there is ongoing I/O
while the user decides to suspend, resume and then suspend the system
again. This due to that after the resume, an mmc_rescan() work gets punted
to the workqueue, which job is to verify that the card remains inserted
after the system has resumed.
To fix this problem, userspace needs to become frozen to suspend the I/O,
prior to turning off the card detection mechanism. Therefore, let's drop
the PM notifiers for mmc subsystem altogether and rely on the card
detection to be turned off/on as a part of the system_freezable_wq, that we
are already using.
Moreover, to allow and SDIO card to be removed during system suspend, let's
manage this from a ->prepare() callback, assigned at the mmc_host_class
level. In this way, we can use the parent device (the mmc_host_class
device), to remove the card device that is the child, in the
device_prepare() phase.
Reported-by: Kiwoong Kim <kwmad.kim@samsung.com>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210310152900.149380-1-ulf.hansson@linaro.org
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 917a5336f2c27928be270226ab374ed0cbf3805d upstream.
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 147186f531ae49c18b7a9091a2c40e83b3d95649 upstream.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97fce126e279690105ee15be652b465fd96f9997 upstream.
In command queueing mode, the cache isn't flushed via the mmc_flush_cache()
function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a
FLUSH_CACHE opcode. In this path, we need to check if cache has been
enabled, before deciding to flush the cache, along the lines of what's
being done in mmc_flush_cache().
To fix this problem, let's add a new bus ops callback ->cache_enabled() and
implement it for the mmc bus type. In this way, the mmc block device driver
can call it to know whether cache flushing should be done.
Fixes: 1e8e55b670 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Reported-by: Brendan Peter <bpeter@lytx.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Brendan Peter <bpeter@lytx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com
Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com
[Ulf: Squashed the two patches and made some minor updates]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aea0440ad023ab0662299326f941214b0d7480bd upstream.
The cache function can be turned ON and OFF by writing to the CACHE_CTRL
byte (EXT_CSD byte [33]). However, card->ext_csd.cache_ctrl is only
set on init if cache size > 0.
Fix that by explicitly setting ext_csd.cache_ctrl on ext-csd write.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210420134641.57343-3-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2970134b927834e9249659a70aac48e62dff804a upstream.
Bus power may control card power, but the full reset done by SDHCI at
initialization still may not reset the power, whereas a direct write to
SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if
the card was left powered on previously.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21e35e898aa9ef7781632959db8613a5380f2eae upstream.
For data read commands, SDHC may initiate data transfers even before it
completely process the command response. In case command itself fails,
driver un-maps the memory associated with data transfer but this memory
can still be accessed by SDHC for the already initiated data transfer.
This scenario can lead to un-mapped memory access error.
To avoid this scenario, reset SDHC (when command fails) prior to
un-mapping memory. Resetting SDHC ensures that all in-flight data
transfers are either aborted or completed. So we don't run into this
scenario.
Swap the reset, un-map steps sequence in sdhci_request_done().
Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Pradeep P V K <pragalla@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e29c84857e2d51aa017ce04284b962742fb97d9e upstream.
A 'tmio_mmc_host_free()' call is missing in the remove function, in order
to balance a 'tmio_mmc_host_alloc()' call in the probe.
This is done in the error handling path of the probe, but not in the remove
function.
Add the missing call.
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142953.918608-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b03aec1c1f337dfdae44cdb0645ecac34208ae0a upstream.
A 'uniphier_sd_clk_enable()' call should be balanced by a corresponding
'uniphier_sd_clk_disable()' call.
This is done in the remove function, but not in the error handling path of
the probe.
Add the missing call.
Fixes: 3fd784f745 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142935.918554-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 774514bf977377c9137640a0310bd64eed0f7323 upstream.
An issue has been observed on STM32MP157C-EV1 board, with an erase command
with secure erase argument, ending up waiting for ~4 hours before timeout.
The requested busy timeout from the mmc core ends up with 14784000ms (~4
hours), but the supported host->max_busy_timeout is 86767ms, which leads to
that the core switch to use an R1 response in favor of the R1B and polls
for busy with the host->card_busy() ops. In this case the polling doesn't
work as expected, as we never detects that the card stops signaling busy,
which leads to the following message:
mmc1: Card stuck being busy! __mmc_poll_for_busy
The problem boils done to that the stm32 variants can't use R1 responses in
favor of R1B responses, as it leads to an internal state machine in the
controller to get stuck. To continue to process requests, it would need to
be reset.
To fix this problem, let's set MMC_CAP_NEED_RSP_BUSY for the stm32 variant,
which prevent the mmc core from switching to R1 responses. Additionally,
let's cap the cmd->busy_timeout to the host->max_busy_timeout, thus rely on
86767ms to be sufficient (~66 seconds was need for this test case).
Fixes: 94fe2580a2 ("mmc: core: Enable erase/discard/trim support for all mmc hosts")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20210225145454.12780-1-yann.gautier@foss.st.com
Cc: stable@vger.kernel.org
[Ulf: Simplified the code and extended the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5b1c6dc13daec60405ecd31eaa5379a9f798fa8 ]
The device_* calls were added a few years ago to abstract
DT/ACPI/fwnode firmware interfaces. Lets convert the two
sdhci caps fields to use the generic calls rather than the OF
specific ones. This has the side effect of allowing
ACPI based devices to quirk themselves when the caps field
is broken.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201120233831.447365-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f9833d3ec8da34861cd0680b00c73e653877eb9 ]
The RPi4 has an Arasan controller it carries over from the RPi3 and a newer
eMMC2 controller. Because of a couple of quirks, it seems wiser to bind
these controllers to the same driver that DT is using on this platform
rather than the generic sdhci_acpi driver with PNP0D40.
So, BCM2847 describes the older Arasan and BRCME88C describes the newer
eMMC2. The older Arasan is reusing an existing ACPI _HID used by other OSes
booting these tables on the RPi.
With this change, Linux is capable of utilizing the SD card slot, and the
Wi-Fi when booted with UEFI+ACPI on the RPi4.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120000406.1843400-2-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0354ca6edd464a2cf332f390581977b8699ed081 ]
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7dfda4f2cec580c135fd81d96a05006651c128 ]
The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so
set the quirk.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ]
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c256a8b0dc09c305c409d6264cc016af2ba38d ]
'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.
This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d15cbf63515c6183d2ed7c9dd0586b4db23ffb1 ]
'dma_request_chan()' calls should be balanced by a corresponding
'dma_release_channel()' call.
Add the missing call both in the error handling path of the probe function
and in the remove function.
Fixes: ff65ffe46d ("mmc: Add Actions Semi Owl SoCs SD/MMC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201209194202.54099-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f92e04f764b86e55e522988e6f4b6082d19a2721 upstream.
When analysing tuples fails we may loop indefinitely to retry. Let's avoid
this by using a 10s timeout and bail if not completed earlier.
Signed-off-by: Fengnan Chang <fengnanchang@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210123033230.36442-1-fengnanchang@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7fb9c24209556478e65211d7a1f056f2d43cceb upstream.
The implementation of sdhci_pltfm_suspend() is only available when
CONFIG_PM_SLEEP is set, which triggers a linking error:
"undefined symbol: sdhci_pltfm_suspend" when building sdhci-brcmstb.c.
Fix this by implementing the missing stubs when CONFIG_PM_SLEEP is unset.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 5b191dcba719 ("mmc: sdhci-brcmstb: Fix mmc timeout errors on S5 suspend")
Cc: stable@vger.kernel.org
Tested-By: Nicolas Schichan <nschichan@freeebox.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b191dcba719319148eeecf6ed409949fac55b39 upstream.
Commit e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
that added a shutdown callback to the diver, is causing "mmc timeout"
errors on S5 suspend. The problem was that the "remove" was queuing
additional MMC commands after the "shutdown" and these caused
timeouts as the MMC queues were cleaned up for "remove". The
shutdown callback will be changed to calling sdhci-pltfm_suspend
which should get better power savings because the clocks will be
shutdown.
Fixes: e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210107221509.6597-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3ed0dc3594d99ff341ec63865a40519ea24b8d upstream.
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1219c0a7432272324660fc9f61a9940f90c50b upstream.
Commit a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for
RPMB") began to use ACMD23 for RPMB if the host supports ACMD23. In
RPMB ACM23 case, we need to set bit 31 to CMD23 argument, otherwise
RPMB write operation will return general fail.
However, no matter V4 is enabled or not, the dwcmshc's ARGUMENT2
register is 32-bit block count register which doesn't support stuff
bits of CMD23 argument. So let's handle this specific ACMD23 case.
From another side, this patch also prepare for future v4 enabling
for dwcmshc, because from the 4.10 spec, the ARGUMENT2 register is
redefined as 32bit block count which doesn't support stuff bits of
CMD23 argument.
Fixes: a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for RPMB")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201229161625.38255233@xhacker.debian
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
